Conductivity,structure, and thermal properties of chitosan‐based polymer electrolytes with nanofillers

This paper focus on the effect of nanosize (<50 nm BET) inorganic alumina (Al₂O₃) filler on the structural, conductivity, and thermal properties of chitosan‐based polymer electrolytes. Films of chitosan and its complexes were prepared using solution‐casting technique. Different amounts of Al₂O₃ viz., 3, 4.5, 6, 7.5, 9, 12, and 15 wt% were added to the highest room temperature conducting sample in the chitosan–salt system, i.e. sample containing 60 wt% chitosan–40 wt% NH₄SCN. The conductivity value of the sample is 1.29 × 10^?4 S cm^?1. On addition of 6 wt% Al₂O₃ filler the ionic conductivity increased to 5.86 × 10^?4 S cm^?1. The amide and amino peaks in the spectrum of chitosan at 1636 and 1551 cm^?1, respectively, shift to lower wavenumbers on addition of salt. The glass transition temperature T_g for the highest conducting composite is 190°C. The increase in T_g with increase in more than 6 wt% filler content is attributed to the increase in degree of crystallinity as proven from X‐ray diffraction studies. Copyright © 2009 John Wiley & Sons, Ltd.     

Natural and synthetic solid polymer hybrid dual network membranes as electrolytes for direct methanol fuel cells

Hybrid dual-network membranes comprising chitosan (CS)–polyvinyl alcohol (PVA) networks crosslinked with sulfosuccinic acid (SSA) and glutaraldehyde (GA) and modified with stabilized silicotungstic acid (SWA) are reported for their application in direct methanol fuel cells (DMFCs). Physico-chemical properties of these membranes are evaluated using thermo-gravimetric analysis and scanning electron microscopy in conjunction with their mechanical properties. Based on water sorption and proton conductivity measurements for the membranes, the optimum content of 10 wt.% SWA in the membrane is established. The methanol crossover for these membranes are studied by measuring the mass balance of methanol using density meter and are found to be lower compared to Nafion-117 membrane. The membrane–electrode assembly with 10 wt.% stabilized SWA–CS–PVA hybrid membrane with SSA and GA as crosslinking agent delivers a peak power density of 156 mW cm⁻² at a load current density of 400 mA cm⁻² and 88 mW cm⁻² at a load current density of 300 mA cm⁻², respectively, in DMFC at 70 °C.     

Novel sulfonated polyimide/ZrO2 composite membrane as a separator of vanadium redox flow battery

Sulfonated polyimide (SPI) and ZrO₂ are blended to prepare a series of novel SPI/ZrO₂ composite membranes for vanadium redox flow battery (VRFB) application. Results of atomic force microscopy and X‐ray diffraction reveal that ZrO₂ is successfully composited with SPI. All SPI/ZrO₂ membranes possess high proton conductivity (2.96–3.72 × 10^?2 S cm^?1) and low VO²⁺ permeability (2.18–4.04 × 10^?7 cm² min^?1). SPI/ZrO₂‐15% membrane is determined as the optimum one on account of its higher proton selectivity and improved chemical stability. The VRFB with SPI/ZrO₂‐15% membrane presents higher coulombic efficiency and energy efficiency than that with Nafion 117 membrane at the current density, which ranged from 20 to 80 mA cm^?2. Cycling tests indicate that the SPI/ZrO₂‐15% membrane has good operation stability in the VRFB system. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Synthesis and Characterization of Phenolphthalein‐Containing Sulfonated Poly(arylene ether phosphine oxide)s by Direct Polycondensation for Proton Exchange Membrane

A series of novel phenolphthalein‐containing sulfonated poly(arylene ether phosphine oxide)s (sPAEPP) with various sulfonation degrees were synthesized by direct polycondensation. The structure of sPAEPP was confirmed by ¹H‐NMR, ¹³C‐NMR, and IR spectroscopy. The high‐molecular weight of these polymers was determined by gel permeation chromatography (GPC). The transparent, tough, and flexible membranes could be achieved by solution casting. The macroscopic properties and microstructure of the obtained membranes were investigated in detail. The results showed that these sPAEPP membranes displayed excellent properties in terms of swelling, proton conductivity, and methanol permeability. For example, sPAEPP‐100 membrane exhibited an appropriate water uptake of 33.1%, a swelling ratio of only 11.7% (lower than 20.1% of Nafion 117), a proton conductivity of 0.11 S cm^?1 (similar to that of Nafion 117) at 80 °C, and a methanol permeability of 4.82 × 10^?7 cm² s^?1. Meanwhile, it also presented outstanding oxidative stability. Atomic force microscope (AFM) micrographs showed that the hydrophilic domains of the sPAEPP‐100 membrane formed connected and narrow ionic channels, which contributed to its high proton conductivity and good dimensional stability. As a result, sPAEPP‐100 membrane displays excellent application prospect for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1097–1104     

Effect of molecular weight and degree of deacetylation on controlled release of isoniazid from chitosan microspheres

Glutaraldehyde cross‐linked chitosan microspheres for controlled release of isoniazid were prepared using chitosan of different molecular weights (MWs) and degrees of deacetylation (DDAs). Chitosan microspheres were characterized for their size, hydrophobocity, degree of swelling and loading of isoniazid. Hydrophobicity of chitosan microspheres increased on increasing the degree of cross‐linking and MW of chitosan. Chitosan microspheres with high degree of deacetylation (DDA) (75 wt%), high MW chitosan (2227 kg mol^?1), and with 12 wt% concentration of glutaraldehyde showed optimum loading and release of isoniazid. The isoniazid from chitosan microspheres was released in two steps, i.e. burst (%R_B) and controlled (%R_C) steps. The microspheres with low MW chitosan (260 kg mol^?1) and low DDA (48 wt%) showed prominent burst release of isoniazid, but microspheres with high MW chitosan (2227 kg mol^?1) and high DDA (75 wt%) have released more isoniazid in a controlled manner (60 wt%) at 37°C in a solution of pH 5.0 ± 0.1. The burst step of drug release (%R_B) has followed first order kinetics, whereas controlled step of drug release (%R_C) followed zero order kinetics. The burst step of drug release was Fickian and controlled step was non‐Fickian in nature. The diffusion constant (D) for isoniazid release was influenced by the properties of chitosan and degree of cross‐linking. Copyright © 2007 John Wiley & Sons, Ltd.     

Polyaniline decorated graphene oxide on sulfonated poly(ether ether ketone) membrane for direct methanol fuel cells application

In direct methanol fuel cells (DMFC), methanol crossover is a major issue which has reduced the performance of polymer electrolyte membrane (PEM) for energy generation. In this study, graphene oxide (GO) and conductive polyaniline decorated GO (PANI-GO) were used as additives in fabrication of sulfonated poly(ether ether ketone) (SPEEK) nanocomposite PEM membrane to reduce methanol crossover. PANI-GO was synthesized by in situ polymerization method and the formation of PANI coated GO nanostructures was confirmed by surface morphology and crystallinity analysis. The membrane morphology and topography analysis confirmed that GO and PANI-GO were well dispersed on the surface of SPEEK membrane. 0.1 wt% PANI-GO modified SPEEK nanocomposite membrane exhibited the highest water uptake and ion exchange capacity of 40% and 1.74 meq g^?1, respectively. The oxidative stability of the nanocomposite membranes also improved. Lower methanol permeability of 4.33 × 10^?7 cm^?2S^?1 was noticed for 0.1 wt% PANI-GO modified SPEEK membrane. PANI-GO modified SPEEK membrane enhanced the proton conductivity, which was due to the existence of acidic and hydrophilic group present in PANI and GO. PANI-GO modified SPEEK membrane held higher selectivity of 1.94 × 10⁴ S cm^?3 s^?1. Overall, these studies revealed that PANI-GO modified SPEEK membrane is a potential material for DMFC applications.     

Novel sulfonated poly (ether ether ketone)/silica coated carbon nanotubes high‐performance composite membranes for direct methanol fuel cell

The major risk of using carbon nanotubes (CNTs) to modify proton exchange membranes (PEMs) in fuel cells is possible short‐circuiting due to the excellent electrical conductivity of CNTs. In this article, silica‐coated CNTs (SiO₂@CNTs) were successfully prepared by a simple sol–gel process and then used as a new additive in the preparation of sulfonated poly (ether ether ketone) (SPEEK)‐based composite membranes. The insulated and hydrophilic silica coated on the surface of CNTs not only eliminated the risk of short‐circuiting, but also enhanced the interfacial interaction between CNTs and SPEEK, and hence promoted the homogeneous dispersion of CNTs in the SPEEK matrix. Moreover, compared to the methanol permeability of the pure SPEEK membrane (3.42 × 10^?7 cm² s^?1), the SPEEK/SiO₂@CNT composite membrane with a SiO₂@CNT loading of 5 wt% exhibits almost one order of magnitude decrease of methanol crossover, while the proton conductivity still remained above 10^?2 S cm^?1 at room temperature. The obtained results expose the possibility of SPEEK/SiO₂@CNT membranes to be served as high‐performance PEMs in direct methanol fuel cells. Copyright © 2015 John Wiley & Sons, Ltd.     

Enhancing proton conductivity of proton exchange membrane with SPES nanofibers containing porous organic cage

Effective proton conducting sites and establishing proton channels are two critical factors in developing high‐performance proton exchange membranes. This study first establishes a strategy in designing effective proton conducting channels for Nafion by using solution blowing of sulfonated polyethersulfone (SPES) nanofibers containing CC3, which is an emerging porous organic cage that possesses the advantages of dissolvable organic solvents and high proton conduction from its interconnected three‐dimensional pore structure. Our strategy results in SPES nanofiber networks with CC3 uniformly involved in and composite membranes with Nafion‐filled interfiber voids. Benefiting from such structural features, the composite membrane exhibits high proton conductivity (0.315 S cm^?1 at 80°C and 100% RH), low methanol permeability (0.69 × 10^?7 cm² S^?1), excellent water absorption, thermal and dimensional stability, and single‐cell performance. This study provides not only a valuable reference for the application of CC3 but also a new idea for establishment of proton transfer channels.     

Composite polymer electrolyte membranes comprising P(VDF‐co‐CTFE)‐g‐PSSA graft copolymer and zeolite for fuel cell applications

Hybrid organic/inorganic composite polymer electrolyte membranes based on a poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) grafted membrane and varying concentrations of zeolite were investigated for application in proton exchange membrane fuel cells (PEMFC). A proton conducting comb copolymer consisting of poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(styrene sulfonic acid) (PSSA) side chains, i.e. P(VDF‐co‐CTFE)‐g‐PSSA (graft copolymer) with 47 wt% of PSSA was synthesized using atom transfer radical polymerization (ATRP) and solution blended with zeolite. Upon incorporation of zeolite, the symmetric stretching band of both SO group (1169 cm^?1) and the ? OH group (3426 cm^?1) shifted to lower wavenumbers. The shift in these FT‐IR spectra suggests that the zeolite particles strongly interact with the sulfonic acid groups of PSSA chains. When the weight percent of zeolite 5A is above 7%, the proton conductivity at room temperature was reduced to 0.011 S/cm. The water uptake of the composite membranes decreased from 234 to 125% with an increase of the zeolite 5A weight percent to 10 wt%. The decrease in water uptake is likely a result of the decrease in the number of available water absorption sites because of the hydrogen bonding interactions between the zeolite particles and the graft copolymer matrix. This behavior is successfully investigated by scanning electron microscopy (SEM). The results of thermal gravimetric analysis (TGA) also showed that all the membranes were stable up to 300°C. Copyright © 2009 John Wiley & Sons, Ltd.     

Modification of hydrophilic channels in Nafion membranes by DMBA: Mechanism and effects on proton conductivity

Modification of proton conductive channels (PCCs) in Nafion has been achieved with the assistance of 3, 4‐dimethylbenzaldehyde (DMBA). During annealing, ionic clusters develop from small isolated spheres (1.72 nm) to wide continuous channels (5.15 nm), and the crystallinity of Nafion/DMBA membranes is also improved from 17% to 32% as shown by X‐ray diffraction. Molecular dynamic simulation reveals that hydrogen bonding and hydrophobic interaction between DMBA and Nafion work synergistically to achieve better phase separation. The morphology–property relationship shows that, versus various PCCs width, the corresponding proton conductivities vary greatly from 0.079 to 0.139 S/cm at 80 °C. By carefully tuning the width of PCCs, the proton conductivity shows an improvement of 22–34% as compared with pristine Nafion. A significant enhancement on the maximum power density is achieved for the membrane electrode assembly on Nafion/DMBA‐8h (as high as 1018 mW/cm^?2), yielding an enhancement of 39% on pristine Nafion‐8h (730 mW/cm^?2). © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 52, 1107–1117     

Dual‐Mode Antibacterial Conjugated Polymer Nanoparticles for Photothermal and Photodynamic Therapy

In this work, dual‐mode antibacterial conjugated polymer nanoparticles (DMCPNs) combined with photothermal therapy (PTT) and photodynamic therapy (PDT) are designed and explored for efficient killing of ampicillin‐resistant Escherichia coli (Amp^r E. coli). The DMCPNs are self‐assembled into nanoparticles with a size of 50.4 ± 0.6 nm by co‐precipitation method using the photothermal agent poly(diketopyrrolopyrrole‐thienothiophene) (PDPPTT) and the photosensitizer poly[2‐methoxy‐5‐((2‐ethylhexyl)oxy)‐p‐phenylenevinylene] (MEH‐PPV) in the presence of poly(styrene‐co‐maleic anhydride) which makes nanoparticles disperse well in water via hydrophobic interactions. Thus, DMCPNs simultaneously possess photothermal effect and the ability of sensitizing oxygen in the surrounding to generate reactive oxygen species upon the illumination of light, which could easily damage resistant bacteria. Under combined irradiation of near‐infrared light (550 mW cm^?2, 5 min) and white light (65 mW cm^?2, 5 min), DMCPNs with a concentration of 9.6 × 10^?4 µm could reach a 93% inhibition rate against Amp^r E. coli, which is higher than the efficiency treated by PTT or PDT alone. The dual‐mode nanoparticles provide potential for treating pathogenic infections induced by resistant microorganisms in clinic.     

Preparation and characterization of branched and linear sulfonated poly(ether ketone sulfone) proton exchange membranes for fuel cell applications

Branched sulfonated poly(ether ketone sulfone)s (Br‐SPEKS) were prepared with bisphenol A, bis(4‐fluorophenyl)sulfone, 3,3′‐disodiumsulfonyl‐4,4′‐difluorobenzophenone, and THPE (1,1,1‐tris‐p‐hydroxyphenylethane), respectively, at 180 °C using potassium carbonate in NMP (N‐methylpyrrolidinone). THPE, as a branching agent, was used with 0.4 mol % of bisphenol A to synthesize branched copolymers. Copolymers containing 10–50 mol % disulfonated units were cast from dimethylsulfoxide solutions to form films. Linear sulfonated poly(ether ketone sulfone)s (SPEKS) were also synthesized without THPE. The films were converted from the salt to acid forms with dilute hydrochloric acid. A series of copolymers were studied by Fourier transform infrared, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water and methanol. The ion‐exchange capacity (IEC), a measure of proton conductivity, was evaluated. The synthesized Br‐SPEKS and SPEKS membranes exhibit conductivities (25 °C) from 1.04 × 10^?3 to 4.32 × 10^?3 S/cm, water swell from 20.18 to 62.35%, IEC from 0.24 to 0.83 mequiv/g, and methanol diffusion coefficients from 3.2 × 10^?7 to 4.7 × 10^?7 cm²/S at 25 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1792–1799, 2008     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Comparison of Electrochemical Synthesis of Ammonia by Using Sulfonated Polysulfone and Nafion Membrane with Sm1.5Sr0.5NiO4

Polysulfone (PSF) and sulfonated polysulfone (SPSF) were synthesized and characterized by IR spectrum. Sm_1.5Sr_0.5NiO₄ (SSN) and Ni‐Ce_0.8Sm_0.2O_2?δ (Ni‐SDC, Ni‐samarium doped ceria) were prepared and characterized by X‐ray diffraction (XRD) and scanning electron microscopy (SEM). Ammonia was synthesized from wet hydrogen and dry nitrogen with applied voltage, using SSN as cathode, Ni‐SDC as anode, Nafion and SPSF as proton membrane respectively. The performances of Nafion and SPSF membranes in ammonia synthesis were investigated and compared at atmospheric pressure and low temperature (25–100°C). The results demonstrated that the proton conducting performances of Nafion and SPSF membranes were similar and the highest rates of evolution of ammonia were up to 1.05×10^?8 and 1.03×10^?8 mol·cm^?2·s^?1 respectively at 80°C and 2.5 V.     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Amide and Acyl‐Hydrazine Functionalized Calix[4]arenes as Carriers for Hydrogen Phosphate Selective Electrodes

Anion‐selective solvent polymeric membrane based on hydrogen bond‐forming, neutral ionophores with amide or acyl‐hydrazine groups are described. The use of the two calix[4]arenes results in anion‐selective electrodes with a selectivity for phosphate. The electrodes of the optimum characteristic have the composition of 1 wt% ionophore, 66 wt% o‐NPOE, 33 wt% poly (vinyl chloride) (PVC) and TDMACl (15 or 30 mol% relative to the ionophore 1 and 2 , respectively). The optimized membrane electrodes show Nernstian responses towards monohydrogen phosphate (?29.1 and ?29.3 mV/decade) based on ionophore 1 and 2 , respectively, in a wide concentration range (1.0×10^?5 to 1.0×10^?2 or 1.0×10^?5 to 1.0×10^?1 M). The selectivity coefficients are determined with the fixed interference method and the activity ratio method. The electrodes display an anti‐Hofmeister series selectivity pattern and highly selective for HPO₄^2? over Cl^?, Br^?, CH₃COO^?, NO₃^? and SO₄^2?. The lifetime of the electrodes is at least 1 month and their response time is found to be 25 s. The proposed sensors could be put to analytical use both by direct potentiometry as well as potentiometric titration.     

Preliminary evaluation of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid composite membranes for direct methanol fuel cell applications

A series of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid (SPEEK/MEA/AA) composite membranes are prepared and investigated to assess their possibility as proton exchange membranes in direct methanol fuel cells (DMFCs). A preliminary evaluation shows that introducing MEA and AA into SPEEK matrix decreases the thermal stability of membrane. However, the degradation temperatures are still above 260 °C, satisfying the requirement for fuel cell operation. Compared with the pure SPEEK membrane, the composite membranes exhibit not only lower water uptake and swelling ratios but also better mechanical property and oxidative stability. Noticeably, the methanol diffusion coefficient of the composite membranes decrease significantly from 3.15 × 10^?6 to 0.76 × 10^?6 cm²/s with increasing MEA and AA content, accompanied by only a small sacrifice in proton conductivity. Although both the methanol diffusion coefficient and the proton conductivity of composite membranes are lower than those of pure SPEEK and Nafion® 117 membranes, their selectivity (conductivity/methanol diffusion coefficient) are higher. In addition, the composite membranes show excellent stability in aqueous methanol solution. The good thermal and chemical stability, low swelling ratio, excellent mechanical property, low methanol diffusion coefficient, and high selectivity make the use of these composite membranes in DMFCs quite attractive. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2871–2879, 2007     

Microporous 3D aluminum MOF doped into chitosan‐based mixed matrix membranes for ethanol/water separation

An aluminum metal–organic framework (Al‐MOF), [Al(OH)(BPDC)] (DUT‐5; BPDC = Biphenyl‐4,4′‐dicarboxylate), was synthesized using solvothermal reactions. The high surface area and micropores (approximately 1.2 nm) of DUT‐5 were characterized using N₂ gas sorption measurements. The thermal stability of DUT‐5 and its phase purity were also investigated. The different amounts of DUT‐5 (0.1, 0.15, and 0.2 wt%) were successfully incorporated into the chitosan (CS) polymer to prepare a mixed matrix membrane (MMM) for the pervaporation of water/ethanol at 25°C. In particular, when 0.15 wt% of DUT‐5 was loaded, the DUT‐5@CS MMMs displayed excellent permeability and selectivity in ethanol/water separation. The results indicated that compared with pristine chitosan membranes, the flux of DUT‐5@CS membranes with 0.15 wt% loading significantly increased from 315 to 378 (g/m² h^?1) and the separation factor from 347 to 3,429. These promising results of the microporous Al‐MOF doped into chitosan MMMs reveal its good application potential for the bio‐ethanol separation processes.     

Guest‐Assisted Proton Conduction in the Sulfonic Mesoporous MIL‐101 MOF

Post‐synthesis modification of MIL‐101(Cr)‐NO₂ was explored in order to decorate the organic backbone by propyl‐sulfonic groups, with the aim to incorporate mobile and acidic protons for solid‐state proton electrolyte applications. The resulting solid switched from insulating towards proton superconductive behavior under humidity, while the conductivity recorded at 363 K and 95 % relative humidity reached 4.8×10^?3 S cm^?1. Propitiously, the impregnation of the material by strong acidic molecules (H₂SO₄) further boosted the proton conductivity performances up to the remarkable σ value of 1.3×10^?1 S cm^?1 at 363 K/95 % RH, which reaches the performances of the best proton conductive MOF reported so far.