Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Sulfonated and crosslinked polyphosphazene-based proton-exchange membranes

Proton-exchange membranes, for possible use in H₂/O₂ and direct methanol fuel cells have been fabricated from poly[bis(3-methylphenoxy)phosphazene] by first sulfonating the base polymer with SO₃ and then solution-casting thin films. The ion-exchange capacity of the membrane was 1.4 mmol/g. Polymer crosslinking was carried out by dissolving benzophenone photoinitiator in the membrane casting solution and then exposing the resulting films after solvent evaporation to UV light. The crosslinked membranes look particularly promising for possible proton exchange membrane (PEM) fuel cell applications. A sulfonated and crosslinked polyphosphazene membrane swelled less than Nafion 117 in both water and methanol. Proton conductivities in crosslinked and non-crosslinked 200 μm thick water-equilibrated polyphosphazene films at temperatures between 25°C and 65°C were essentially the same and only 30% lower than those for Nafion 117. Additionally, water and methanol diffusivities in the crosslinked polyphosphazene membrane were very low (≤1.2×10⁻⁷ cm²/s). Sulfonated/crosslinked polyphosphazene films showed no signs of mechanical failure (softening) up to 173°C and a pressure of 800 kPa and did not degrade chemically when soaked in a hot hydrogen peroxide/ferrous ion solution.     

Optimal method for preparing sulfonated polyaryletherketones with high ion exchange capacity by acid-catalyzed crosslinking for proton exchange membrane fuel cells

Sulfonated polyaryletherketones (SPAEK) bearing four sulfonic acid groups on the phenyl side groups were synthesized. The benzophenone moiety of polymer backbone was further reduced to benzydrol group with sodium borohydride. The membranes were crosslinked by acid-catalyzed Friedel-Crafts reaction without sacrifice of sulfonic acid groups and ion exchange capacity (IEC) values. Crosslinked membranes with the same IEC value but different water uptake could be prepared. The optimal crosslinking condition was investigated to achieve lower water uptake, better chemical stability (Fenton's test), and higher proton conductivity. In addition, the hydrophilic ionic channels from originally course and disordered could be modified to be narrow and continuous by this crosslinking method. The crosslinked membranes, CS4PH-40-PEKOH (IEC = 2.4 meq./g), reduced water uptake from 200 to 88% and the weight loss was reduced from 11 to 5% during the Fenton test compared to uncrosslinked one (S4PH-40-PEK). The membrane showed comparable proton conductivity (0.01–0.19 S/cm) to Nafion 212 at 80°C from low to high relative humidity (RH). Single H₂/O₂ fuel cell based on the crosslinked SPAEK with catalyst loading of 0.25 mg/cm² (Pd/C) exhibited a peak power density of 220.3 mW/cm², which was close to that of Nafion 212 (214.0 mW/cm²) at 80°C under 53% RH. These membranes provide a good option as proton exchange membrane with high ion exchange capacity for fuel cells.     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Polymeric proton conducting membranes for medium temperature fuel cells (110–160°C)

The availability of stable polymeric membranes with good proton conductivity at medium temperatures is very important for the development of methanol PEM fuel cells. In view of this application, a systematic investigation of the conductivity of Nafion 117 and sulfonated polyether ether ketone (S-PEEK) membranes was performed as a function of relative humidity (r.h.) in a wide range of temperature (80–160°C). The occurrence of swelling/softening phenomena at high r.h. values prevented conductivity determinations above certain temperatures. Nevertheless, when r.h. was maintained at values lower than 80%, measurements were possible up to 160°C. The results showed that Nafion is a better proton conductor than S-PEEK at low r.h. values, especially at temperatures lower than 120°C. The differences in conductivity were, however, leveled out with the increasing r.h. and temperature. While at 100°C and 35% r.h. the conductivity of S-PEEK 2.48 was about 30 times lower than the conductivity of Nafion, both membranes reached a comparable conductivity (4×10⁻² S cm⁻¹) at 160°C and 75% r.h. The effect of superacidity and crystallization of the polymers on the conductivity, as well as the possibility of using Nafion and S-PEEK membranes in medium temperature fuel cells, are discussed.     

The effect of crosslinked networks with poly(ethylene glycol) on sulfonated polyimide for polymer electrolyte membrane fuel cell

To investigate the effect of crosslinking by a hydrophilic group on a sulfonated polyimide electrolyte membrane, sulfonated polyimide end‐capped with maleic anhydride was synthesized using 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl, 2,2′‐disulfonic acid, 2‐bis [4‐(4‐aminophenoxy)phenyl] hexafluropropane and maleic anhydride. The sulfonated polyimides end‐capped with maleic anhydride were self‐crosslinked or crosslinked with poly(ethylene glycol) diacrylate. A series of the crosslinked sulfonated polyimides having various ratios of sulfonated polyimide and poly(ethylene glycol) diacrylate were prepared and compared with uncrosslinked and self‐crosslinked sulfonated polyimides. The synthesized sulfonated polyimide films were characterized for FTIR spectrum, thermal stability, ion exchange capacity, water uptake, hydrolytic stability, morphological structure, and proton conductivity. The formation of sulfonated polyimide was confirmed in FTIR spectrum. Thermal stability was good for all the sulfonated polyimides that exhibited a three‐step degradation pattern. Ion exchange capacity was the same for both the uncrosslinked and the self‐crosslinked sulfonated polyimides (1.30 mEq/g). When the crosslinked sulfonated polyimides with poly(ethylene glycol) were compared, the ion exchange capacity was decreased as 1.27 > 1.25 > 1.23 mEq/g and water uptake was increased as 23.8 < 24.0 < 24.3% with the increase in poly(ethylene glycol) diacrylate content. All the crosslinked sulfonated polyimides with poly(ethylene glycol) diacrylate were stable for over 200 h at 80 °C in deionized water. Morphological structure and mean intermolecular distance were obtained by WAXD. Proton conductivities were measured at 30, 50, 70, and 90 °C. The proton conductivity of the crosslinked sulfonated polyimides with poly(ethylene glycol) diacrylate increased with the increase in poly(ethylene glycol) diacrylate content despite the fact that the ion exchange capacity was decreased. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1455–1464, 2005     

Energy material - the role of silicotungstic acid and fly ash in sulfonated poly (ether sulfone) composites for PEMFC applications

The composite polymer electrolyte membranes were prepared from sulfonated poly (ether sulfone) (SPES), silicotungstic acid (STA) and fly ash (FA). Post sulfonation process was adopted to synthesize SPES using sulphuric and chlorosulfonic acid. The prepared electrolyte membranes were examined by water uptake capacity, swelling ratio, ion-exchange ability, proton conductivity, thermal stability and electrochemical performance for evaluating the pertinence of these membranes in fuel cell applications. As such the pristine membrane restricts with the proton conductivity of 0.042?S cm^?1 at 30?°C and 0.060?S cm^?1 at 90?°C while the polymer composite membrane, SP-STA-FA-10 reveals the maximum conductivity of 0.054?S cm^?1 at 30?°C and 0.073?S cm^?1 at 90?°C. It also exhibits good thermal stability than that of the pure membrane. The membrane electrode assemblies (MEAs) have been successfully developed from SPES as well as SP-STA-FA-10 membranes and their electrochemical performance were studied the wide range of current density. Herein, the composite membranes derived from SPES, STA and FA can be viable candidates for fuel cell applications.     

The stability of semi-interpenetrating polymer networks based on sulfonated polyimide and poly(ethylene glycol) diacrylate for fuel cell applications

A series of the semi-interpenetrating polymer network (semi-IPN) membranes based on sulfonated polyimide and poly(ethylene glycol) diacrylate were prepared and characterized comparing with pure sulfonated polyimide membrane and commercially available membrane, Nafion^® 117. The proton conductivity increased with the increase of poly(ethylene glycol) diacrylate contents in spite of the decrease in ion exchange capacity which is a key factor to improve the proton conductivity. The water stability of semi-IPN membranes containing poly(ethylene glycol) diacrylate is higher than the pure sulfonated polyimide membrane. Morphological structure showed that amorphous nature of the films also increased with the poly(ethylene glycol) diacrylate contents, which could make a crosslink, so that the crystallinity of polyimide could disappear. Semi-IPN membranes based on sulfonated polyimide and poly(ethylene glycol) diacrylate, which show good conductivity comparable to Nafion^® 117 in the range of 20-50% content of poly(ethylene glycol) diacrylate, could be promising proton conducting membranes in fuel cell application.     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Characterizations and stability of polyimide-phosphotungstic acid composite electrolyte membranes for fuel cell

Organic-inorganic composite membranes from partially aliphatic sulfonated polyimides and heteropolyacids (HPAs) were synthesized. A series of composite membranes with varying amounts of heteropolyacid were prepared by altering the weight ratio of polyimide and HPA. The partially aliphatic sulfonated polyimides are synthesized from 1,4,5,8-naphthalenetetracarboxylic dianhydride, 4,4′-diaminobiphenyl 2,2′-disulfonic acid as the sulfonated diamine, and decamethylenediamine as the aliphatic diamine. The incorporation of HPA is confirmed by FT-IR analyses. When appropriately embedded in a hydrophilic polymer matrix, the hydrated HPAs are expected to endow the composite membrane with their high proton conductivity, while retaining the desirable mechanical properties of the polymer film. These composite membranes were evaluated for thermal stability, ion exchange capacity, water uptake and proton conductivity. Also the extraction of HPA from the polyimide membranes and their stability in water were determined. Though water uptake and IEC decreased with increase in HPA content, the proton conductivity of the composite membranes increased with increase in HPA weight content. This study shows that partially aliphatic sulfonated polyimide composite membranes with HPA can be a viable substitute for Nafion^® for fuel cells which show good conductivity comparable to Nafion^®117 at temperatures nearing 100 °C, keeping in mind that polyimides have good thermal stability and low cost.     

Synthesis and characterization of anhydrous conducting polyimide/ionic liquid complex membranes via a new route for high‐temperature fuel cells

The paper deals with the synthesis and characterization of a new series of anhydrous conducting acid‐doped complex membranes based on polyimide (PI) and ionic liquid (IL) for high‐temperature fuel cells via a new route. For this purpose, three imidazolium‐based ILs (RIm⁺BF₄^?) with different alkyl chain lengths (R=methyl, ethyl, and butyl) are added into polyamic acid (PAA) intermediate prepared from the reaction of benzophenonetetracarboxylic dianhydride and diaminodiphenylsulfone in different –COOH/imidazolium molar ratios (n = 0.5, 1, and 2). Then, the thermally imidized complex membrane was doped with H₂SO₄. The conductivities of acid‐doped PI/IL complex membranes prepared by taking n of 1 are found to be in the range of 10^?4?10^?5 S cm^?1 at 180°C, whereas the acid‐free PI/IL complex membranes show the conductivity at around 10^?9?10^?10 S cm^?1. Thermogravimetric analysis results reveal that the acid‐doped PI/IL complex membranes are thermally stable up to 250°C. Dynamic mechanical analysis results of the acid‐doped ionically interacted complex membrane show that the mechanical strengths of the PI/IL complex membranes including 1‐methyl imidazolium tetrafluoroborate (MeIm‐BF₄) and 1‐ethyl 3‐methyl imidazolium tetrafluoroborate (EtIm‐BF₄) are comparable with those of pristine PI until 200°C. Furthermore, it can be clearly emphasized that the ionic interaction between carboxylic acid groups of PAA's and IL's cations offers a positive role in long‐term conductivity stability by preventing the IL migration at high temperatures. On the other hand, preliminary methanol permeability tests of the acid‐doped membranes show that they can also be considered as an alternative for direct methanol fuel cells. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis of ionic polybenzimidazoles with broad ion exchange capacity range for anion exchange membrane fuel cell application

In this study, new anion exchange membranes (AEM) based on crosslinked polybenzimidazole (m-PBI) with quaternary ammonium groups, crosslinkable allyl groups, and hydrophobic ethyl groups as side chains are synthesized and characterized. The AEMs are crosslinked by thermal thiol-ene reaction using a dithiol crosslinker. The ion exchange capacity (IEC) values and crosslinking density were controlled by the number of quaternary ammonium groups and allyl groups, respectively. The introduction of ethyl groups improved the solubility of ionic PBIs even at very low IEC values by eliminating the hydrogen bonding interaction of imidazole rings. This method allows ionic PBIs with broad IEC values, from 0.75 to 2.55 mmol/g, to be prepared. The broad IEC values were achieved by independently controlling the numbers of quaternary ammonium groups, allyl groups, and hydrophobic ethyl groups during preparation. The crosslinked ionic PBIs revealed hydroxide conductivity from 16 to 86 mS/cm at 80°C. The wet membranes also showed excellent mechanical strength with tensile strength of 12.2 to 20.1 MPa and Young's Modulus of 0.67 to 1.45 GPa. The hydroxide conductivity of a crosslinked membrane (0.40Q0.60Et1.00Pr, IEC = 0.95 mmol/g) decreased only 7.9% after the membranes was immersed in a 1.0 M sodium hydroxide solution at 80°C for 720 h. A single fuel cell based on this membrane showed a maximum peak power density of 136 mW/cm² with a current density of 377 mA /cm² at 60°C.     

Synthesis and properties of novel sulfonated polyimides containing 1,5‐naphthylene moieties

A series of novel sulfonated polyimides (equivalent weight per sulfonic acid = 310–744 g/equiv) containing 10–70 mol % 1,5‐naphthylene moieties were synthesized as potential electrolyte materials for high‐temperature polymer electrolyte fuel cells. The polycondensation of 1,4,5,8‐naphthalene tetracarboxylic dianhydride, 4,4′‐diamino‐2,2′‐biphenyldisulfonic acid, and 1,5‐diaminonaphthalene gave the title polymer electrolytes. The polyimide electrolytes were high‐molecular‐weight (number‐average molecular weight = 36.0–350.7 × 10³ and weight‐average molecular weight = 70.4–598.5 × 10³) and formed flexible and tough films. The thermal properties (decomposition temperature > 260 °C, no glass‐transition temperature), stability to oxidation, and water absorption were analyzed and compared with those of perfluorosulfonic acid polymers. The polyimide containing 20 mol % 1,5‐naphthylene moieties showed higher proton conductivity (0.3 S cm^?1) at 120 °C and 100% relative humidity than perfluorosulfonic acid polymers. The temperature and humidity dependence of the proton conductivity was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3901–3907, 2003     

Preliminary evaluation of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid composite membranes for direct methanol fuel cell applications

A series of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid (SPEEK/MEA/AA) composite membranes are prepared and investigated to assess their possibility as proton exchange membranes in direct methanol fuel cells (DMFCs). A preliminary evaluation shows that introducing MEA and AA into SPEEK matrix decreases the thermal stability of membrane. However, the degradation temperatures are still above 260 °C, satisfying the requirement for fuel cell operation. Compared with the pure SPEEK membrane, the composite membranes exhibit not only lower water uptake and swelling ratios but also better mechanical property and oxidative stability. Noticeably, the methanol diffusion coefficient of the composite membranes decrease significantly from 3.15 × 10^?6 to 0.76 × 10^?6 cm²/s with increasing MEA and AA content, accompanied by only a small sacrifice in proton conductivity. Although both the methanol diffusion coefficient and the proton conductivity of composite membranes are lower than those of pure SPEEK and Nafion® 117 membranes, their selectivity (conductivity/methanol diffusion coefficient) are higher. In addition, the composite membranes show excellent stability in aqueous methanol solution. The good thermal and chemical stability, low swelling ratio, excellent mechanical property, low methanol diffusion coefficient, and high selectivity make the use of these composite membranes in DMFCs quite attractive. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2871–2879, 2007     

Crosslinked sulfonated polyimide networks as polymer electrolyte membranes in fuel cells

Sulfonated polyimides with tertiary nitrogen in the polymer backbone were synthesized with 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, 2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, and diaminoacrydine hemisulfate. They were crosslinked with a series of dibromo alkanes to improve the hydrolytic stability. The crosslinked sulfonated polyimide films were characterized for their thermal stability, ion‐exchange capacity (IEC), water uptake, hydrolytic stability, and proton conductivity. All the sulfonated polyimides had good thermal stability and exhibited a three‐step degradation pattern. With an increase in the alkyl chain length of the crosslinker, IEC decreased as 1.23 > 1.16 > 1.06 > 1.01, and the water uptake decreased as 7.29 > 6.70 > 6.55 > 5.63. The order of the proton conductivity of the crosslinked sulfonated polyimides at 90 °C was as follows: polyimide crosslinked with dibromo butane (0.070) > polyimide crosslinked with dibromo hexane (0.055) > polyimide crosslinked with dibromo decane (0.054). The crosslinked polyimides showed higher hydrolytic stability than the uncrosslinked polyimides. Between the crosslinked polyimides, the hydrolytic stability decreased with an increase in the alkyl chain length of the crosslinker. The crosslinked and uncrosslinked sulfonated polyimides exhibited almost the same proton conductivities. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2370–2379, 2005     

Synthesis and properties of polyimide ionomers containing sulfoalkoxy and fluorenyl groups

A series of sulfopropylated and sulfobutylated polyimide copolymers containing fluorenyl groups, SPI‐4, were synthesized to investigate the effect of alkyl side chains on the properties (stability, mechanical strength, water uptake, and proton conductivity) of the polymimide electrolyte membranes. SPI‐4 showed much better hydrolytic stability (in 10% MeOH aq at 100 °C) than the main chain sulfonated polyimide, SPI‐1. Tough, flexible, and ductile membranes were obtained from these copolymers. At high relative humidity all the SPI‐4 membranes showed high mechanical properties (>34 MPa of the maximum stress) and proton conductivity (>0.1 Scm^?1). These properties are comparable to or even better than those of the perfluorosulfonic acid ionomer (Nafion 112). The new polyimide ionomers have proved to be a possible candidate as polymer electrolyte membrane for PEFCs and DMFCs. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4439–4445, 2005     

Proton conducting membranes based on poly(vinyl chloride) graft copolymer electrolytes

The direct preparation of proton conducting poly(vinyl chloride) (PVC) graft copolymer electrolyte membranes using atom transfer radical polymerization (ATRP) is demonstrated. Here, direct initiation of the secondary chlorines of PVC facilitates grafting of a sulfonated monomer. A series of proton conducting graft copolymer electrolyte membranes, i.e. poly(vinyl chloride)‐g‐poly(styrene sulfonic acid) (PVC‐g‐PSSA) were prepared by ATRP using direct initiation of the secondary chlorines of PVC. The successful syntheses of graft copolymers were confirmed by ¹H‐NMR and FT‐IR spectroscopy. The images of transmission electron microscopy (TEM) presented the well‐defined microphase‐separated structure of the graft copolymer electrolyte membranes. All the properties of ion exchange capacity (IEC), water uptake, and proton conductivity for the membranes continuously increased with increasing PSSA contents. The characterization of the membranes by thermal gravimetric analysis (TGA) also demonstrated their high thermal stability up to 200°C. The membranes were further crosslinked using UV irradiation after converting chlorine atoms to azide groups, as revealed by FT‐IR spectroscopy. After crosslinking, water uptake significantly decreased from 207% to 84% and the tensile strength increased from 45.2 to 71.5 MPa with a marginal change of proton conductivity from 0.093 to 0.083 S cm^?1, which indicates that the crosslinked PVC‐g‐PSSA membranes are promising candidates for proton conducting materials for fuel cell applications. Copyright © 2008 John Wiley & Sons, Ltd.     

New sulfonated engineering polymers via the metalation route. II. Sulfinated/sulfonated poly(ether sulfone) PSU Udel and its crosslinking

New mixed sulfinated/sulfonated polysulfone PSU Udel has been produced by partial oxidation of sulfinated PSU with NaOCl. From the mixed sulfinated/sulfonated PSU, thin crosslinked polymer films have been produced by S-alkylation of the residual sulfinate groups with α,ω-diiodoalkanes having 4–10  (CH₂) units. The advantages of the partial oxidation process using NaOCl are as follows: (1) The desired oxidation degree can be adjusted finely. (2) No side reactions take place during oxidation. (3) The partially oxidized polymers is stable at ambient temperature. By variation of the oxidation degree of the sulfinated/sulfonated prepolymer and by variation of the chain length of the diiodo crosslinker, crosslinked membranes with a large range of properties in terms of ionic conductivity, swelling, and permselectivity have been produced. The partially oxidized polymers have been characterized by redox titration, ¹H-NMR, and FTIR. The crosslinked membranes have been characterized in terms of ionic conductivity (resistance), permselectivity, and swelling in dependence on ion-exchange capacity and oxidation degree of the prepolymers. In addition, the thermal stabilities of the membranes have been determined by TGA, and FTIR spectra have been recorded on the crosslinked films. Selected membranes show low ionic resistances, low swelling, and good temperature stability which makes them promising candidates for application in (electro)membrane processes. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1441–1448, 1998     

Sulfonated silica‐based electrolyte nanocomposite membranes

New functionalized particles were prepared by attaching sulfonated aromatic bishydroxy compounds onto fumed silica surface. First, a bromophenyl group was introduced onto the silica surface by reaction of bromophenyltrimethoxysilane with fumed silica. Then, sulfonated bishydroxy aromatic compounds were chemically attached to the silica surface by nucleophilic substitution reactions. The structure of the modified silica was characterized by elemental analysis: ¹³C‐NMR, ²⁹Si‐NMR, and FTIR. Afterward, novel inorganic–organic electrolyte composite membranes based on sulfonated poly(ether ether ketone) have been developed using the sulfonated aromatic bishydroxy compounds chemically attached onto the fumed silica surface. The composite membrane prepared using silica with sulfonated hydroxytelechelic, containing 1,3,4‐oxadiazole units, has higher proton conductivity values in all range of temperatures (40–140 °C) than the membrane containing only the plain electrolyte polymer, while the methanol permeability determined by pervaporation experiment was unchanged. A proton conductivity up to 59 mS cm^?1 at 140 °C was obtained. The combination of these effects may lead to significant improvement in fuel cells (fed with hydrogen or methanol) at temperatures above 100 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2278–2298, 2006