高度分散的Pt/TiO2的制备及光催化活性

用柠檬酸作为空穴捕获剂和分散剂, 在温和条件下用光催化还原法将3 nm金属铂沉积在7 nm的锐钛矿相及介孔二氧化钛纳米晶表面. TEM观察显示铂的负载量为w＝1.0%时, 多数二氧化钛纳米晶表面沉积了岛状的铂团簇, XPS和电子衍射结果表明铂以游离态存在. 负载w＝1.0%～2.0%铂的TiO₂在苯酚光氧化反应中活性显著提高. Pt/TiO₂在氨气中经550 ℃氮化, 可制得氮掺杂的Pt/TiO₂可见光光催化剂, 氮化过程中铂团簇没有烧结和显著长大.     

掺铂二氧化钛纤维光催化降解氯仿的研究

 TiO2纤维作为一种微米级光催化剂应用于废水处理时，不但克服了TiO2纳米颗粒不易分离回收的困难，而且对其进行贵金属掺杂，可使其光催化活性大大提高．用光还原沉积法制备了掺铂的二氧化钛纤维催化剂（Pt／TiO2（F）），并将其作为光催化剂用于光催化降解氯仿反应，考察了掺铂量、氧及pH值等条件对降解氯仿反应的影响，并与掺铂的二氧化钛颗催化剂粒（Pt／TiO2（G））的光催化活性进行了比较．结果表明，当掺铂量w（Pt）＝0．5％，催化剂用量为0．5g／L，预先溶氧至饱和状态，c0（CHCl3）＝1mmol／L，pH＝5，用300W中压汞灯光照120min时，Pt／TiO2（F）上氯仿的降解率可达98．44％，而Pt／TiO2（G）上氯仿的降解率仅为72．03％．     

氮铂共掺杂纳米二氧化钛的制备及表征

采用溶胶-凝胶法制备了氮掺杂纳米TiO2(N-TiO2),并用光分解沉积法在N-TiO2表面负载上微量金属Pt形成铂-氮共掺杂纳米TiO2(Pt/N-TiO2).通过X射线衍射、光电子谱、紫外-可见吸收、扫描电镜和光电流测试对催化剂进行了表征.结果表明:Pt和N共掺杂对TiO2的晶型和形貌影响不大,但其吸收边带较纳米TiO2约红移20nm,Pt/N-TiO2电极在可见光区的光电流约为纳米TiO2电极的4倍.     

二氧化钛纤维表面担载Pt纳米结构的原子力显微镜研究

通过原子力显微镜研究了二氧化钛纤维表面担载Pt的表面形貌及其结构.结果表明,TiO2纤维表面担载的Pt具有微米尺度的近似六边形或者近似长方形的结构,与在单晶TiO2(110)表面的Pt纳米簇形貌相似,但尺度较大.TiO2纤维担载的Pt表面明显存在不同高度的台阶结构,台阶高度以2~4倍Pt(111)晶面面间距的高度为主.由Pt在TiO2纤维表面的形貌与纤维的纳米晶粒排布有序性推测可知,Pt与TiO2纤维存在强的相互作用,可能正是这种强相互作用和表面台阶结构才使TiO2表面担载的Pt虽是微米尺寸但仍具有高光催化活性.     

有机钌螯合物/TiO_2杂化膜修饰电极上Pt纳米团簇的光电流增强效应

利用LB膜技术可控制备了纳米单层和多层的二氧化钛-有机钌螯合物杂化膜,并研究了上述无机-有机杂化膜修饰电极在Pt纳米团簇敏化后的光电流增强效应.实验结果表明:(1)纳米单层TiO2/[Ru(phen)2(dC18bpy)]2+(简称为TiO2-Ru)杂化膜的平均厚度为(3.6±0.5)nm;(2)在光照条件下TiO2-Ru杂化膜能有效催化还原[Pt(NH3)6]4+形成粒径位于20～160nm之间的Pt纳米团簇;(3)Pt纳米团簇的引入消除了金属钌螯合物中配体对电子传递的阻碍作用,改变了电子传递途径,从而有效减少了电子空穴对的复合,提高了Pt纳米团簇敏化的n层杂化膜修饰电极(ITO/(TiO2-Ru)n/Pt)在支持电解质中的光电流.与纳米单层TiO2-Ru杂化膜修饰的ITO电极(ITO/TiO2-Ru)相比,当工作电压为900mV时,ITO/TiO2-Ru/Pt在0.1mol·L-1的NaClO4电解质溶液中和光照(λ360nm)条件下,单位面积的光电流提高了约5倍;(4)ITO/(TiO2-Ru)n/Pt电极光电流的大小与杂化膜的层数密切相关,当TiO2-Ru杂化膜的层数从一层、二层增加到四层时,光电流呈现先升高后下降行为,这表明ITO/(TiO2-Ru)n/Pt电极的电子传递过程直接通过非电活性的二氧化钛纳米单层进行.     

Pt/TiO2催化剂的制备及其在氨催化氧化中的应用

二氧化钛具有优良的光催化性能,以其为载体通过光催化还原沉积可在其表面实现单质金属活性组分负载。本研究选择二氧化钛颗粒为载体,通过紫外光照射在二氧化钛颗粒表面还原沉积铂单质,形成Pt/ TiO2核壳结构,并将该新型催化剂用于氨催化氧化反应。所制备的Pt/TiO2催化剂铂负载量减为0.2 gPt/ gTiO2,比表面积增达10 m2/ g。以该催化剂催化氨氧化反应,氨转化率在600-700 篊即可达100 %,低于目前硝酸工业中氨氧化反应温度800-900 篊,也低于PtO2升华温度850 篊。该催化剂经400 h连续反应,其铂载量、及催化活性均无降低,具有工业应用前景。     

Pt/TiO_2催化剂的制备及其在氨催化氧化中的应用

二氧化钛具有优良的光催化性能,以其为载体通过光催化还原沉积可在其表面实现单质金属活性组分负载.选择二氧化钛颗粒为载体,通过紫外光照射在二氧化钛颗粒表面还原沉积铂单质,形成Pt/TiO2负载型催化剂,并将该新型催化剂用于氨催化氧化反应.所制备的Pt/TiO2催化剂铂负载量减为0.2 gPt/gTiO2,比表面积增达10 m2/g.以该催化剂催化氨氧化反应,氨转化率在600~700℃即可达100%,低于目前硝酸工业中氨氧化反应温度800~900℃,也低于PtO2升华温度850℃.该催化剂经400 h连续反应,其铂载量、及催化活性均无降低,具有工业应用前景.     

纳米TiO2-Pt修饰电极的制备及电催化活性

采用电化学合成前驱体直接水解法和电沉积法制备高活性纳米TiO2-Pt修饰电极，并使用扫描电子显微镜(SEM)对电极的表面形貌和结构进行了表征; 通过循环伏安法研究了纳米TiO2-Pt修饰电极在H2SO4溶液中的电化学行为以及对Mn2＋氧化为Mn3＋的电催化活性. 结果表明,纳米TiO2的晶粒大小约30 nm,修饰在纳米TiO2膜表面的Pt微粒呈现单分散状态,平均粒径约60 nm,纳米TiO2-Pt修饰电极的电化学性能优于纯Pt电极,对Mn2＋的电氧化具有高催化活性,非均相无隔膜电解氧化Mn2＋生成Mn3＋平均电流效率可达86％.     

乙二醛在Ti/纳米TiO2-Pt修饰电极上的电催化氧化

采用溶胶-凝胶和电沉积法制备Ti基纳米TiO2-Pt(Ti/纳米TiO2-Pt)修饰电极. X射线衍射(XRD)表明纳米TiO2为锐钛矿型, 扫描电镜(SEM)显示Pt纳米粒子在纳米TiO2多孔膜的表面呈现簇分散状态, 平均粒径约25 nm. 通过循环伏安(CV)和计时电流法研究了Ti/纳米TiO2-Pt修饰电极对乙二醛直接电氧化的电催化活性, 结果表明, 修饰电极对乙二醛的直接电氧化呈现良好的催化活性, 在0.60和1.23 V(vs SCE)出现两个氧化峰, 二者电流密度分别为16 和42 mA·cm-2, 约为纯Pt电极的2倍和1.5倍, 反应过程受浓差扩散控制.     

乙二醛在Ti/纳米TiO2-Pt修饰电极上的电催化氧化

采用溶胶.凝胶和电沉积法制备Ti基纳米TiO2-Pt(Ti/纳米TiO2-Pt)修饰电极.X射线衍射(XRD)表明纳米TiO2为锐钛矿型,扫描电镜(SEM)显示Pt纳米粒子在纳米TiO2多孔膜的表面呈现簇分散状态,平均粒径约25nm.通过循环伏安(CV)和计时电流法研究了Ti/纳米TiO2-Pt修饰电极对乙二醛直接电氧化的电催化活性,结果表明,修饰电极对乙二醛的直接电氧化呈现良好的催化活性,在0.60和1.23 V(vs SCE)出现两个氧化峰,二者电流密度分别为16和42 mA·cm2,约为纯Pt电极的2倍和1.5倍,反应过程受浓差扩散控制.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.