笼形聚羧酸钒(Ⅳ)—硫脲体系引发丙烯腈聚合动力学

研究了笼形聚羧酸钒(PV)-硫脲(TU)体系在硝酸溶液中引发丙烯腈(AN)聚合动力学。表观聚合速度(R_p)是 R_p=9.7×10~5e~(-10500)/RT[AN]~1.0[PV]~0.50[TU]~0.76[HNO_3]~1.5聚合诱导期(τ)随反应条件而变化,聚合温度越高,引发种浓度越大,聚合诱导期越短,但与单体浓度的变化无关。 1/τ=4.6×10~(12)e~(-13500)/RT[AN]~0[PV][TU]~(-3/2)[HNO_3]~3=K_τ·R_i聚合物分子量随单体浓度增大而提高,但随聚合温度及引发种浓度增大而下降,即 笼形聚羧酸钒—硫脲体系引发丙烯腈聚合的动力学参数和引发机理与杨梅型聚羧酸钒—硫脲体系在相同的条件下引发聚合的行为有明显的区别,认为是和两种树脂大分子链的空间结构所引起的传质阻力有关。     

笼形聚肟偕亚氨二乙酸钒(Ⅳ)-硫脲体系引发丙烯腈聚合的研究

研究了笼形聚肟偕亚氨二乙酸钒(CPV)-硫脲(TU)体系在硝酸溶液中引发丙烯腈(AN)聚合反应.表观聚合速度(R_P)是 R_P=1.0×10~8e~(-10.500/RT)[AN]~(1.0)[CPV]~(1.0)[TU]~(1.5)[HNO_3]~(3.0) 聚合诱导期(τ)随反应温度和物料浓度发生变化,可表示为 1/τ=5.2×10~9e~(-12.800/RT)[AN]~1.0[CPV]~1.0[TU]~1.5[HNO_3]~3.0实验结果表明,聚合反应以单基终止为特征,可能是和高分子载体较大的空间位阻有关.     

钒(V)—硫脲氧化还原体系引发丙烯腈聚合的研究 Ⅰ.聚合动力学

研究了钒(V)—硫脲氧化还原体系在硝酸溶液中引发丙烯腈的聚合反应.表观聚合速度是:R_p=2.80×10~5e~(-14000/RJ)[AN]~(2.2)[HNO_3]~(0102)[V~(5+)~(0～1/3)[TU]~(0～4/3),实验结果表明钒(V)和硫脲产生引发种是一个相当复杂的过程。     

聚偕氨肟—硫脲络合物的组成对丙烯腈聚合的影响

在聚丙烯基聚偕氨肟(PPAO)—硫脲(TU)体系引发丙烯腈(AN)聚合过程中,将 c(TU)/c(PPAO)摩尔比调节在0.5以上,可以观察到 PPAO、硫脲和硝酸浓度的变化对聚合速度都不产生实质性的影响,但聚合诱导期则随 c(TU)/c(PPAO)摩尔比增大而延长。根据实验结果,得表观聚合速度R_p=2.07e~(-32.6KJ/RT)c~(2.0)(AN)碰撞频率因子极低和引发体系的零级反应是链自由基向初级自由基碰撞终止的特征。     

杨梅型聚丙烯基亚氨二乙酸钒(Ⅳ)—硫脲体系引发丙烯腈聚合的研究

研究了杨梅型聚丙烯基亚氨二乙酸钒(PIDA/VO)—硫脲(TU)体系在硫酸溶液中引发丙烯腈聚合动力学。表观聚合速度(Rp)和聚合物分子量(Mn)可分别表示为: Rp=2.2×10~5e~(-0860)/RT[AN]~1.0[PV]~0.50[TU]~1.5[H_2SO_4]~2.0 Mn=K·1/T·[AN]/[PV]~0.50[TU]~1.5[H_2SO_4]~2.0其中([PV]~0.05[TU]~1.5[H_2SO_4]~2.0)~2是正比于引发种浓度。由此可见,链自由基是以双基反应终止,伯基终止及链转移终止的可能性较少。和聚羧酸钒(Ⅳ)—硫脲体系引发丙烯腈聚合的机理相同,杨梅型聚丙烯基亚氨二乙酸钒(Ⅳ)也表现出强烈的羧基间协同作用和大分子场效应。     

杨梅形聚肟偕亚氨二乙酸钒(Ⅳ)—硫脲体系引发丙烯腈聚合的研究

研究了杨梅形聚肟偕亚氨二乙酸树脂负载VO~(2+)(PV)与疏脲(TU)组合在硝酸溶液中引发丙烯腈(AN)的聚合反应。在实验条件下,表观聚全速度可表示为 R_p=1.91×10~5e~(-45.0/RT)c~(1.9)(AN)c~(1.0)(HNO_3)c~(0.60)(PV)c~(1.50)(TU) 聚合诱导期(τ)与反应物浓度和聚合温度关系是 1/τ=8.27×10~7e~(-38.3/RT)c~(1.9)(HNO_3)c~(0.60)(PV)C~(1.50)(TU)=K_τ;·R_i/R_p 在酸性介质中,氨羧基的协同作用促使键合的VO~(2+)氧化为VO_2~+,随后硫脲配位并通过氢桥缔合,后者分解生成初级自由基,引发丙烯腈的聚合反应。     

丙烯腈在金属镁引发下的聚合动力学

研究了金属镁在硝酸溶液中引发丙烯腈的聚合反应。实验结果表明,聚合速度与金属镁的用量无关,并且当[HNO_3]>[AN]时服从下列关系式: R_p=1.91×10~5e~(-15000/RT)[Mg]~0[AN]~(2.2)[HNO_3]~(0.45) 丙烯腈-丙烯酸甲酯的共聚试验证明,聚合反应是按自由基机理进行。     

阴离子交换树脂负载钒(V)—硫脲氧化还原体系引发丙烯腈聚合的研究

用负载偏钒酸根的强碱性阴离子交换树脂(PV)与硫脲(TU)组成氧化还原体系在硝酸溶液中引发丙烯腈(AN)聚合,表观聚合速度是: R=1.92×10~4e~(-6860)/RT[AN]~(1.2)[RV]~(0.44)[TU]~(1.8)[HNO_ 3]~(1.0)聚合动力学参数与V~(6+)—TU体系所得者不同,表明初级自由基的产生受扩散控制因素的重要影响,并且载体树脂在聚合过程中存在着强烈的大分子场效应。聚合诱导期(ι)与引发速度成反比。聚合物分子量与聚合速度成正比,与终止速度和聚合温度成反比。加料方式实验再一次表明了引发种是由五价钒和硫脲络合和/或缔合所产生而不是和异硫脲结合的结果。本文讨论了引发聚合机理。     

电荷转移聚合研究——三苯基磷引发丙烯腈光聚合

研究了三苯基磷(TPP)引发丙烯腈(AN)光聚合。测定了光聚合速率 R_p与单体浓度、引发剂浓度的关系为:R_p=K[AN]~(1.49)[TPP]~(0.47)以及光聚合反应活化能E_α=6.16千卡/摩尔,从激发态电荷转移机制,讨论了引发聚合机理。     

亚硝酸钠引发丙烯腈聚合的研究

研究了亚硝酸钠引发硝酸溶液中丙烯腈的聚合反应。测得表现聚合速度 Rp=Ae~(-10,800/RT)[AN]~2.2[NaNO_2]~(0.17-1.0)[HNO_3]~(1.0-0.67 丙烯腈-丙烯酸甲酯共聚合反应中竞聚率分别是γ_An=0.96,γ_MA=1.17,表明聚合反应是按自由基机理进行。 根据聚合动力学和红外光谱分析,认为以亚硝酸钠引发硝酸溶液中丙烯腈的聚合反应与电解或金属溶蚀过程中的次级引发相同。     

DEPENDENCE OF ACRYLONITRILE POLYMERIZATION KINETICS ON THE COMPOSITION OF POLYAMIDOXIME-THIOUREA SYSTEM

The polymerization of acrylonitrile (AN) initiated by polypropylene based-polyamidoxime (PPAO)-thiourea (TU) system was investigated at [TU]/[PPAO]>0.5 molar ratio. It shows that the variation of the concentrations of PPAO, thiourea and nitric acid does not exert an observable influence on the reaction rate. The overall rate of polymerization (R_p) isR_p = 2.07e~(-7,800/RT)[ AN]~(2.0)The zero order dependence on PPAO and thiourea concentrations and the lowest value of the collision frequence factor were considered to be a feature of the primary radical termination.     

MECHANISM FOR THE INITIATION OF ACRYLONITRILE POLYMERIZATION BY POLYPROPYLENE-BASED POLYAMIDOXIME-THIOUREA COMBINATION

Polymerization of acrylonitrile (AN) in aqueous nitric acid initiated by polypropylene-based polyamidoxime (PPAO)-thiourea (TU) combination has been investigated. The overall rate of polymerization (R_p) under the conditions of [TU]/[PPAO]<0.5 molar ratio isThe molecular weights of the polymers were found to be inversely proportional to 3/2-power of nitric acid concentration and 1-power of thiourea concentration. In addition, it is independent with the concentrations of monomer and PPAO, and decreases with increasing temperature.On the basis of these experimental results, a coordination-proton transfer mechanism for the initiation was proposed and discussed.     

聚丙烯基聚肟偕亚氨二乙酸合铜(Ⅱ)—亚硫酸钠体系引发甲基丙烯酸甲酯的聚合动力学

研究了聚丙烯基聚肟偕亚氨二乙酸合铜(Ⅱ)(P-Cu)—亚硫酸钠体系引发水溶液中甲基丙烯酸甲酯的聚合反应。表观聚合速度(Rp)是 Rp=5.8×10~(12)e~(-84·2KJ/RT)[MMA]~(1·4)[P-Cu]~0[Na_2SO_3]~(0·50) 聚合的引发种被认为是通过“络合—氢转移”机理产生。     

AM/(2-甲基丙烯酰氧乙基)三甲基氯化铵/2-丙烯酰胺基-2-甲基丙基磺酸钠的反相微乳液共聚合动力学研究

通过实验绘制了失水山梨醇单月桂酸酯(Span20)-聚氧乙烯山梨醇酐单脂酸酯(Tween80)复配乳化剂、丙烯酰胺、(2-甲基丙烯酰氧乙基)三甲基氯化铵、2-丙烯酰胺基-2-甲基丙基磺酸钠和环己烷的拟三元相图.采用过硫酸铵-亚硫酸氢钠氧化还原引发剂,通过动力学研究,得到了聚合反应的表观活化能为68.10 kJ/mol,并分别得到了聚合速率与产物特性粘数的动力学关系式Rp∝[M]1.74[APS]0.60[E]-1.28,[η]∝[M]0.78[APS]-0.23[E]-0.71,分析了单体浓度、引发剂浓度、乳化剂浓度对共聚合反应速率Rp和共聚物特性粘数[η]作用及影响的原因,在动力学研究的基础上初步探讨了聚合机理.     

DYE-SENSITIZED PHOTOLYSIS OF o-Cl-HEXAARYLBIIMIDAZOLE AND PHOTOPOLYMERIZATION KINETICS STUDY OF THE LONG WAVE-LENGTH DYE/HEXAARYLBIIMIDAZOLE SYSTEMS*

o-Chloro-hexaarylbiimidazole (o-Cl-HABI) can be sensitized efficiently by the dyes 1-ethyl-3'-methyl thiacyaninebromide (C 1), 3,3'-diethyl thiacarbocyanine iodide (C 2), and cyclopentanone 2,5-bis[2-(1,3-dihydro-1,3,3-trimethyl-2H-indol-2-ylidene)ethylidene] (C 3) through electron transfer proceses. When exposed to a xenon lamp (filtered by Pyrex glass),the photosensitive systems composed of o-Cl-HABI and the above dyes can produce free radicals which initiate thepolymerization of MMA. The photopolymerization kinetics equation was obtained for the o-Cl-HABI/C2 system, R_p=K [C2]~(0.75)[o-Cl-HABI]~(0.44)[MTA]~(0.12)[MMA]~(10). A comparison of the influence of different dyes on the conversion of MMA photopolymerization was conducted.     

INFLUENCES OF WATER-SOLUBLE CATIONIC MONOMERS ON THE POLYMERIZATION RATE IN THE INVERSE EMULSION

This investigation deals with the free radical polymerization both of (2-methacryloyloxy-ethyl) trimethyl ammonium chloride (QACEMA) and of diallyldimethyl ammoniumcbloride (DADMAC) in inverse emulsion. The influences of some factors, such as theconcentration of monomers, initiator and emulsifier are discussed. The polymerization rateequations of above two monomers can be written as follows:R_p= k[M]~(1.21) [I]~(0.82) [E]~(0.57) (for QACEMA)R_p= k'[M]~(1.34) [I]~(0.90)[E]~(0.62)(for DADMAC)