双盘工作电极参比电位采样快扫伏安方法

报道一种双铂盘工作电极、相应的毛细管参比电极和竖直式电化学池设计并用于快速循环伏安测量.双工作电极包括一个常规工作电极,一个辅助工作电极.后者在使用中接地,仅提供参比电位来控制工作电极的电位.参比毛细管尖端安设在接近辅助工作电极的位置上;用0.3mm直径Pt盘工作电极,在电位扫描速度高达10kV/s都可以得到类似于100%iR补偿的伏安曲线,而不必使用iR补偿电路.本文围绕高扫速伏安法中工作电极电位的准确控制问题做了一些初步的探讨.     

Enhanced electrochemiluminescent of lucigenin at an electrically heated cylindrical microelectrode

In this paper, an ECL detection system equipped with an electrically heating controlled cylindrical microelectrode (HME) was used to study the ECL behavior of lucigenin. The ECL intensity of lucigenin would be increased at elevated electrode temperature but the noise had not been increased. It was found that ECL intensity at higher temperature of electrode surface (80 °C) was more than two magnitudes stronger than that at the room temperature (22 °C). The detection limit for ECL of lucigenin on a HME is much lower than that on an electrode without heating, based on which, it is possible to establish a more sensitive method for measurement of ECL by using a HME. The heating of electrode has been used to renew the electrode, which avoid the tedious work for refreshing the electrode surface. The reproducibility of lucigenin ECL system at HME is satisfactory.     

Sensitive Flow-Injection Electrochemical Determination of Hydrogen Peroxide at a Palladium Nanoparticle-Modified Pencil Graphite Electrode

A novel flow-injection amperometric method was proposed for the sensitive and enzymeless determination of hydrogen peroxide based on its electrocatalytic reduction at a palladium nanoparticle-modified pretreated pencil graphite electrode in a laboratory-constructed electrochemical flow cell. Cyclic voltammograms of the unmodified and modified electrodes were recorded in pH 7.0 phosphate buffer containing 0.10 M KCl at a scan rate of 50?mV s^?1 for the investigation of electrocatalytic reduction of hydrogen peroxide at the palladium nanoparticle-modified pretreated pencil graphite electrode. Cyclic voltammograms of the pretreated pencil graphite electrode revealed an irreversible oxidation peak and a weak reduction peak of hydrogen peroxide at +1100?mV and –450?mV vs. an Ag/AgCl/KCl saturated reference electrode. However, the reduction of hydrogen peroxide was observed at –100?mV with an increase in current in the cyclic voltammograms of the palladium nanoparticle-modified pretreated pencil graphite electrode compared to the unmodified electrode. These results indicate that the palladium nanoparticle-modified pretreated pencil graphite electrode exhibits efficient electrocatalytic activity for the reduction of hydrogen peroxide. A linear concentration range was obtained between .01 and 10.0?mM hydrogen peroxide with a detection limit of 3.0 µM from flow injection amperometric current–time curves recorded in pH 7.0 phosphate buffer at –100?mV and a 2.0?mL min^?1 flow rate. The novelty of this work relies on its use of a laboratory-constructed flow cell constructed for the pencil graphite electrode using these inexpensive, disposable, and electrochemically reactive modified electrodes for the amperometric determination of hydrogen peroxide in a flow injection analysis system.     

Catalysis of dioxygen reduction at soluble polyaniline modified electrode

A reflux-treatment of soluble polyaniline (SPA) in dimethylformamide (DMF) containing CoCl₂ yields an active catalyst for dioxygen reduction which can be adsorbed on the electrode surface firmly. The catalytic reduction of dioxygen at the glassy carbon (GC) electrode modified by the catalyst was studied with cyclic voltammetry (CV), rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE). The kinetic process of dioxygen reduction at the modified electrode was analyzed with a new RRDE theory dealing with a nondiffusion-controlled process on ring electrode. The rate constants for each scheme of dioxygen reduction were calculated, showing that only 2-electron reduction to H₂O₂ was conducted at the modified electrode. The effect of solution acidity on the electrocatalytic behaviour for dioxygen reduction was investigated. A possibility of initiating catalytic activity for dioxygen reduction was explored with ESCA method.     

Activation effects of a platinum electrode by laser pulse irradiation on the electro-oxidation of glucose in alkaline solution.

In order to demonstrate the activation effects of a Pt electrode by laser pulse irradiation, the electro-oxidation of glucose was tested at an activated Pt electrode by cyclic voltammetry. A fixed potential was applied to the electrode, and then the electrode was irradiated with laser pulses from a Nd:YAG laser at 20 Hz for 20 s. Activation by the laser pulse irradiation gave two remarkable effects on cyclic voltammograms from the electro-oxidation of glucose in a 0.1 mol dm(-3) NaOH solution, i.e., surface modulation and cleaning effects. Significant differences were found in the cyclic voltammograms at the activated and at the simply polished electrodes. Such differences in the oxidation waves are attributed to a crystallographic change of the electrode surface induced by a laser ablation, accompanied by laser pulse irradiation. Due to the cleaning effect, the activated Pt electrode gave a sharp oxidation wave at -0.3 V even in real samples containing various organic compounds that could foul the electrode, though the activated Pt electrode lacked selectivity to the electro-oxidation of glucose.     

Determination of taurine in human tear fluid by capillary electrophoresis with indirect amperometric detection based on electrogenerated bromine

A new method for the determination of taurine was developed based on indirect amperometric detection after capillary electrophoresis. A serial dual‐electrode detector comprising an on column Pt film electrode (upstream electrode) and an end column Pt microdisk electrode (downstream electrode) was utilized to conduct the indirect amperometric detection. Bromide is oxidized to bromine at upstream electrode and reduced back to bromide at downstream electrode. Since taurine can react with bromine quantitatively and rapidly, its concentration can therefore be determined by the decrease of the current for bromine reduction at the downstream electrode. Principal experimental parameters governing the analytical performance were investigated and optimized. Under the optimal conditions, taurine can be baseline separated from interfering amino acids and the detection limit of 0.18 μM was obtained with a linear correlation coefficient of 0.999 over the concentration range of 0.5–60 μM. The developed method has been successfully applied in the determination of taurine in human tear fluid. The taurine level obtained was in good agreement with previous reports and recoveries for taurine spiked ranged from 92–95% with relative standard deviations within 4.6%, demonstrating the reliability of the developed method in the determination of taurine in human tear fluid.     

Theory of the steady-state current of a redox couple at interdigitated array electrodes of which pairs are insulated electrically by steps

The possibility of constructing an interdigitated array electrode (IDA) with a submicrometre gap is proposed in which adjacent microband electrodes are separated from each other by an insulated step. Then the IDA is an assembly of protrusive and hollow microband electrodes. The unit model of the IDA consisted of half of the lower (hollow) microband electrode, an insulated step and half of the upper (protrusive) microband electrode with a finite thickness on the step. The boundary value problem involving the two-dimensional Laplace equation is presented for redox cycling at the IDA under diffusion control and is solved numerically by a boundary element method. The steady-state current was computed as a function of the height of the step and the thickness of the upper electrode. It was larger than the current at the ordinary IDA, partly because the true electrode area was larger than the area of the ordinary IDA. The current varied linearly with the logarithm of the step height. It was expressed by a simple approximate equation in order to facilitate prediction of its numerical value.     

Monitoring metal ion contamination onset in hydrofluoric acid using silicon-diamond and dual silicon sensing electrode assembly.

Potentiometric detection of trace levels of metallic contamination onset in hydrofluoric acid using a silicon-based sensor in conjunction with two non-contaminating reference electrode systems is presented in this paper. In the first case, conductive diamond was used as a non-contaminating reference electrode. Cyclic voltammetry and open-circuit potential experiments demonstrated the feasibility of using a conductive diamond film electrode as a quasi-reference electrode in the HF solution. In the second case, a dual silicon electrode system was used with one of the silicon-based electrodes protected with an anion permeable membrane behaving as the quasi-reference electrode. The dual silicon sensing electrode system possessed an additional operational advantage of being unaffected by the solution acidity. Though both sensing configurations were able to detect the metal ion contamination onsets at the parts-per-trillion to parts-per-billion levels, the dual silicon electrode design showed a greater compatibility for the on-line detection of metallic impurities in HF etching baths commonly used in semiconductor processing.     

生理条件下对苯二酚的电化学行为及电极产物的色谱鉴定

用循环伏安法研究了对苯二酚在玻碳电极上的电化学行为，从循环伏安图上看出当在0至1．6V电位间连续扫描20次，在0．63V左右可见到一氧化峰电位，其峰电流随扫描次数的增加而减小。说明电极反应为不可逆过程。然而，如改变在-1．4～1.6V电位间扫描，仅数次扫描后即可在Epa=0．25V和Epc=-0．08V处见到一对氧化还原峰电位，说明了此过程为一可逆过程。同时，对电极反应的产物用RHPLC进行研究和鉴定，从色谱图所示结果与电化学法所得结果一致。根据此工作的研究结果对苯二酚在呼吸链中所产生的作用进行了探讨。     

Band-type microelectrodes for amperometric immunoassays

A band-type microelectrode was made using a parylene-N film as a passivation layer. A circular-type, mm-scale electrode with the same diameter as the band-type microelectrode was also made with an electrode area that was 5000 times larger than the band-type microelectrode. By comparing the amperometric signals of 3,5,3′,5′-tetramethylbenzidine (TMB) samples at different optical density (OD) values, the band-type microelectrode was determined to be 9 times more sensitive than the circular-type electrode. The properties of the circular-type and the band-type electrodes (e.g., the shape of their cyclic voltammograms, the type of diffusion layer used, and the diffusion layer thickness per unit electrode area) were characterized according to their electrode area using the COMSOL Multiphysics software. From these simulations, the band-type electrode was estimated to have the conventional microelectrode properties, even when the electrode area was 100 times larger than a conventional circular-type electrode. These results show that both the geometry and the area of an electrode can influence the properties of the electrode. Finally, amperometric analysis based on a band-type electrode was applied to commercial ELISA kits to analyze human hepatitis B surface antigen (hHBsAg) and human immunodeficiency virus (HIV) antibodies.     

Sensitive Electrochemical Detection of Oxalate at a Positively Charged Boron‐Doped Diamond Surface

Allyltriethylammonium bromide (ATAB) was covalently attached to the surface of hydrogen‐terminated boron‐doped diamond (BDD) thin films using a photochemical method to fabricate positively charged electrode surfaces. The anodic current for oxalate oxidation both in cyclic voltammetry and in flow‐injection analysis with amperometry was found to be up to two times larger at ATAB‐modified BDD (ATAB‐BDD) than at an unmodified BDD electrode, which may be based on the electrostatic interaction between the oxalate anion and the electrode surface. In addition, the stability of the electrochemical detection of oxalate was improved at the ATAB‐BDD electrode compared to the unmodified electrode.     

Electrochemical properties and the determination of nicotine at a multi-walled carbon nanotubes modified glassy carbon electrode

Electrochemical properties of nicotine at the glassy carbon electrode modified with multi-walled carbon nanotubes were explored. Nicotine underwent irreversible reduction at the modified electrode, which was an adsorption-controlled process with two protons and two electrons. The reductive peak current of nicotine significantly increased at the modified electrode compared with the bare glassy carbon electrode, suggesting that the multi-walled carbon nanotubes can enhance the electron transfer rate. The current was proportional to the concentration of nicotine over two line ranges, and the detection limit was 9.3 µM (at S/N?=?3). For ten parallel detections of 0.62 mM nicotine, the relative standard deviation was 2.67%, suggesting that the film modified electrode had excellent reproducibility. The modified electrode was applied to the direct determination of nicotine in tobacco samples with good sensitivity, selectivity and stability.     

Hybridization detection of enzyme-labeled DNA at electrically heated electrodes

In this report we describe an electrochemical DNA hybridization sensor approach, in which signal amplification is achieved using heated electrodes together with an enzyme as DNA-label. On the surface of the heatable low temperature co-fired ceramic (LTCC) gold electrode, an immobilized thiolated capture probe was hybridized with a biotinylated target using alkaline phosphatase (SA-ALP) as reporter molecule. The enzyme label converted the redox-inactive substrate 1-naphthyl phosphate (NAP) into the redox-active 1-naphthol voltammetrically determined at the modified gold LTCC electrode. During the measurement only the electrode was heated leaving the bulk solution at ambient temperature. Elevated temperature during detection led to increased enzyme activity and enhanced analytical signals for DNA hybridization detection. The limit of detection at 53 °C electrode temperature was 1.2 nmol/L.     

Stripping voltammetry of silver(I) with a carbon-paste electrode modified with thiacrown compounds

The accumulation behaviour and stripping voltammetry of silver(I) was investigated with a carbon-paste electrode modified with a thiacrown compound. Silver could be accumulated at the electrode in the absence of an applied potential by immersing the electrode in a solution of sodium perchlorate containing silver(I), then reduced at constant potential in 0.1M acetate buffer solution. Finally a well-defined stripping peak could be obtained by scanning the potential in a positive direction. The calibration curve for silver was linear over the range 0.5-2.5 muM with accumulation for 5 min. Studies of the effect of other metal ions showed that the silver was selectively accumulated at the electrode.     

γ干扰素免疫电极及其响应机理的研究

在醋纤维孔膜上利用溴化氰固定了马抗人γ干扰素抗体。抗体膜经竞争性温育反应后置于碘离子选择电极上而构成免疫电极; 另一碘电极与参比膜作为参比电极。测定了电极在0.1mmol.dm^-3KI+4.4mmol.dm^-3H2O2+0.1mol.dm^-3柠檬酸盐,PH5.0缓冲液中响应电位, 研究了温度反应时间、电解液组成等因对电极响应影响,提出了电极向应线性化方法, 并得到了实验验证。     

Implementation of a Chloride‐selective Electrode Into a Closed Bipolar Electrode System with Fluorimetric Readout

Applicability of a bipolar electrode system was tested for arrangements containing a typical ion‐selective electrode (ISE) connected with an electrode coated by a conducting polymer characterized by electroluminescence. In this case a selective response of the ISE membrane at one pole of the bipolar electrode is transduced to a fluorimetric signal obtained by reduction of the conducting polymer at the second pole. This signal transformation mode was studied on example of a simple closed bipolar electrode system composed of all‐solid‐state chloride‐selective electrode with polypyrrole transducer as the sensing pole and the reporting pole represented by electrode coated by poly(3‐octylthiophene) (POT) layer characterized by fluorescence in the neutral state. In this system selective and linear dependences of fluorimetric signal on logarithm of chloride ions concentration in turn‐on mode were recorded for optimized external voltage applied. Alternatively, a concept of cascade bipolar electrode system with incorporation of additional bipolar electrode being a polarization source for the sensing bipolar electrode with ISE and POT layer was also tested. A significant advantage of the cascade system is its possibility to work spontaneously without external polarization. For this case also linear calibration plots of fluorimetric signal vs. logarithm of analyte concentration were recorded.     

Multi-analyte sensing: a chemometrics approach to understanding the merits of electrode arrays versus single electrodes

A peptide-modified electrode array with a different peptide on each electrode is compared with a single electrode modified with many peptides for the voltammetric measurement of concentrations of Cu(2+), Cd(2+) and Pb(2+) in solution. The single gold electrode was modified simultaneously with peptides Gly-Gly-His, glutathione and angiotensin I each coupled to thioctic acid, and thioctic acid itself, and the calibration of mixtures of ions was compared with previously published data from an array of four sensors each with an individual modification. Calibration at the multi-peptide single-electrode sensor was by two-way partial least squares (voltammetric current measured with variables 'sample' x 'potential') and for the electrode array by three-way NPLS1 ('sample' x 'potential' x 'electrode'). The advantage of designing experiments to yield multi-way data is demonstrated and discussed.     

Comparison of Boron‐Doped Diamond and Glassy Carbon Electrodes for Determination of Procaine Hydrochloride

The electrochemical oxidation of procaine hydrochloride (PC?HCL, 2‐diethylaminoethyl 4‐aminobenzoate hydrochloride) was investigated at as‐deposited boron‐doped diamond (ad‐BDD) electrode, anodically oxidized BDD (ao‐BDD) electrode and glassy carbon (GC) electrode using cyclic voltammetry (CV). Well‐defined cyclic voltammograms were obtained for PC?HCL oxidation with high signal‐to‐background (S/B) ratio, low tendency for adsorption, good reproducibility and long‐term stability at ad‐BDD electrode, demonstrating its superior electrochemical behavior and significant advantages in contrast to ao‐BDD and GC electrode. At 100 μM PC?HCL, the voltammetric S/B ratio was nearly one order of magnitude higher at an ad‐BDD electrode than that at a GC electrode. In a separate set of experiments for oxidation of 100 μM PC?HCL, 96%, 92% and 84% of the initial oxidation peak current was retained at the ad‐BDD, ao‐BDD and GC electrode, respectively, by stirring the solution after the tenth cycle. The current response was linearly proportional to the square root of the scan rate within the range 10–1000 mV s^?1 in 10 μM PC?HCL solutions, indicating that the oxidation process was diffusion‐controlled with negligible adsorption at an ad‐BDD surface. The good linearity was observed for a concentration range from 5 to 200 μM with a linear equation of y=0.03517x+0.65346 (r=0.999), and the detection limit was 0.5 μM for oxidation of PC?HCL at the ad‐BDD electrode. The ad‐BDD electrode could maintain 100% of its original activity after intermittent use for 3 months.     

超微盘电极上双电位阶跃计时电流和计时库仑法理论及验证

本文报道超微盘电极上双电位阶跃计时电流和计时库仑法理论,用自制的微机多功能电分析仪及亚铁氰化钾、氯化钾体系进行验证,实验结果与理论相符合.     

Cyclic voltammetric simulation of electrochemically mediated enzyme reaction and elucidation of biosensor behaviors

A cyclic voltammetric simulation that can be applied to an electrochemically mediated enzyme reaction involving any substrate and mediator concentration was developed. Concentration polarization of the substrate in the vicinity of an electrode was considered as well as mediator concentration. Reversible electrochemical reaction with one electron followed by an enzyme reaction with two electrons was modeled. The differential equations for the mediator and substrate were solved using digital simulation techniques. The calculated cyclic voltammograms showed prepeaks when there was a low substrate concentration, high mediator concentration, and high enzyme activity. The prepeak was experimentally observed in the case of an enzyme electrode co-immobilized with a redox polymer. The enzyme electrode loaded at high redox polymer and high enzyme content showed a prepeak at low substrate concentration in the cyclic voltammogram.