Crystalline structure and thermal behavior of nylon‐10,14

The structure and morphology of a novel polyamide, nylon‐10,14, and its lamellar crystals from dilute solution were examined by transmission electron microscopy and wide‐angle X‐ray diffraction (WAXD). Both the electron‐diffraction pattern and WAXD data demonstrated that nylon‐10,14 adopts the structure of a triclinic lattice similar to that of the traditional nylon‐66 but with a corresponding increase of the c parameter to 3.23 nm. In addition, the thermal behavior of melt‐crystallized nylon‐10,14 was investigated by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). The glass‐transition temperature of nylon‐10,14 determined by the DMA data was 46.6°C. DSC indicated that the multiple melting behavior of isothermally crystallized nylon‐10,14 probably results from the melt and recrystallization mechanism. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1422–1427, 2003     

Polymer crystalline structure and morphology changes in nylon‐6/ZnO nanocomposites

The influence of ZnO nanoparticles on the crystalline structures of nylon‐6 under different crystallization conditions (annealing at different temperatures from the amorphous solid, isothermal crystallization from the melt at different temperatures, and crystallization from the solution) has been examined with differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, field emission scanning electron microscopy, and Fourier transform infrared. ZnO nanoparticles can induce the γ‐crystalline form in nylon‐6 when it is cooled from the melted state and annealed from the amorphous solid. This effect of ZnO nanoparticles increases with decreasing particle size and changes under different crystallization conditions. The effects of ZnO nanoparticles on the crystallization kinetics of nylon‐6 have also been studied with DSC. The results show that ZnO nanoparticles have two competing effects on the crystallization of nylon‐6: inducing the nucleation but retarding the mobility of polymer chains. Finally, the melting behavior of the composites has been investigated with DSC, and the multiple melting peaks of composites containing ZnO nanoparticles and pure nylon‐6 are ascribed to the reorganization of imperfect crystals. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1033–1050, 2003     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Phase separation,porous structure,and cure kinetics in aliphatic epoxy resin containing hyperbranched polyester

Thermosetting blends of an aliphatic epoxy resin and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 4,4′‐diaminodiphenylmethane (DDM) as the curing agent. The phase behavior and morphology of the DDM‐cured epoxy/HBP blends with HBP content up to 40 wt % were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The cured epoxy/HBP blends are immiscible and exhibit two separate glass transitions, as revealed by DMA. The SEM observation showed that there exist two phases in the cured blends, which is an epoxy‐rich phase and an HBP‐rich phase, which is responsible for the two separate glass transitions. The phase morphology was observed to be dependent on the blend composition. For the blends with HBP content up to 10 wt %, discrete HBP domains are dispersed in the continuous cured epoxy matrix, whereas the cured blend with 40 wt % HBP exhibits a combined morphology of connected globules and bicontinuous phase structure. Porous epoxy thermosets with continuous open structures on the order of 100–300 nm were formed after the HBP‐rich phase was extracted with solvent from the cured blend with 40 wt % HBP. The DSC study showed that the curing rate is not obviously affected in the epoxy/HBP blends with HBP content up to 40 wt %. The activation energy values obtained are not remarkably changed in the blends; the addition of HBP to epoxy resin thus does not change the mechanism of cure reaction of epoxy resin with DDM. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 889–899, 2006     

Poly(hydroxyether of phenolphthalein) and its blends with poly(ethylene oxide)

Poly(hydroxyether of phenolphthalein) (PPH) was synthesized through the polycondensation of phenolphthalein with epichlorohydrin. It was characterized by Fourier transform infrared (FTIR) spectroscopy, NMR spectroscopy, and differential scanning calorimetry (DSC). The miscibility of the blends of PPH with poly(ethylene oxide) (PEO) was established on the basis of the thermal analysis results. DSC showed that the PPH/PEO blends prepared via casting from N,N‐dimethylformamide possessed single, composition‐dependent glass‐transition temperatures. Therefore, the blends were miscible in the amorphous state for all compositions. FTIR studies indicated that there were competitive hydrogen‐bonding interactions with the addition of PEO to the system, which were involved with OH…O?C〈, ? OH…? OH, and ? OH vs ether oxygen atoms of PEO hydrogen bonding, that is both intramolecular and intermolecular, between PPH and PEO). Some of the hydroxyl stretching vibration bands significantly shifted to higher frequencies, whereas others shifted to lower frequencies, and this suggested the formation of hydrogen bonds between the pendant hydroxyls of PPH and ether oxygen atoms of PEO, which were stronger than the intramolecular hydrogen bonding between hydroxyls and carbonyls of PPH. The FTIR spectra in the range of carbonyl stretching vibrations showed that the hydroxyl‐associated carbonyl groups were partially set free because of the presence of the competitive hydrogen‐bonding interactions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 466–475, 2003     

Miscibility and hydrogen‐bonding interactions in blends of carbon dioxide/epoxy propane copolymer with poly(p‐vinylphenol)

The miscibility and hydrogen‐bonding interactions of carbon dioxide and epoxy propane copolymer to poly(propylene carbonate) (PPC)/poly(p‐vinylphenol) (PVPh) blends were investigated with differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy and X‐ray photoelectron spectroscopy (XPS). The single glass‐transition temperature for each composition showed miscibility over the entire composition range. FTIR indicates the presence of strong hydrogen‐bonding interassociation between the hydroxyl groups of PVPh and the oxygen functional groups of PPC as a function of composition and temperature. XPS results testify to intermolecular hydrogen‐bonding interactions between the oxygen atoms of carbon–oxygen single bonds and carbon–oxygen double bonds in carbonate groups of PPC and the hydroxyl groups of PVPh by the shift of C_1s peaks and the evolution of three novel O_1s peaks in the blends, which supports the suggestion from FTIR analyses. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1957–1964, 2002     

Studies on poly(ε‐caprolactone)/thiodiphenol blends: The specific interaction and the thermal and dynamic mechanical properties

The effects of several low molecular weight compounds with hydroxyl groups on the physical properties of poly(ε‐caprolactone) (PCL) were investigated by Fourier transform infrared (FTIR) spectroscopy and high‐resolution solid‐state ¹³C NMR. PCL and 4,4′‐thiodiphenol (TDP) interact through strong intermolecular hydrogen bonds and form hydrogen‐bonded networks in the blends at an appropriate TDP content. The thermal and dynamic mechanical properties of PCL/TDP blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis, respectively. The melting point of PCL decreased, whereas both the glass‐transition temperature and the loss tangent tan δ of the blend increased with an increase in TDP content. The addition of 40 wt % TDP changed PCL from a semicrystalline polymer in the pure state to a fully amorphous elastomer. The molecules of TDP lost their crystallizability in the blends with TDP contents not greater than 40 wt %. In addition to TDP, three other PCL blend systems with low molecular weight additives containing two hydroxyl groups, 1,4‐dihydroxybenzene, 1,4‐di‐(2‐hydroxyethoxy) benzene, and 1,6‐hexanediol, were also investigated with FTIR and DSC, and the effects of the chemical structure of the additives on the morphology and thermal properties are discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1848–1859, 2000     

Synthesis and characterization of liquid‐crystalline epoxy and its blend with conventional epoxy

Terephthaloyl chloride was reacted with 4‐hydroxy benzoic acid to get terephthaloylbis(4‐oxybenzoic) acid, which was characterized and further reacted with epoxy resin [diglycidyl ether of bisphenol A (DGEBA)] to get a liquid‐crystalline epoxy resin (LCEP). This LCEP was characterized by Fourier transform infrared spectrometry, ¹H and ¹³C NMR spectroscopy, differential scanning calorimetry (DSC), and polarized optical microscopy (POM). LCEP was then blended in various compositions with DGEBA and cured with a room temperature curing hardener. The cured blends were characterized by DSC and dynamic mechanical analysis (DMA) for their thermal and viscoelastic properties. The cured blends exhibited higher storage moduli and lower glass‐transition temperatures (tan δ_max, from DMA) as compared with that of the pure DGEBA network. The formation of a smectic liquid‐crystalline phase was observed by POM during the curing of LCEP and DGEBA/LCEP blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3375–3383, 2003     

Phase behavior of blends of PCBM with amorphous polymers with different aromaticity

The phase behavior of [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) blends with amorphous polymers with different degrees of aromaticity has been investigated by differential scanning calorimetry (DSC) and small‐angle neutron scattering (SANS). The polymers investigated are the homologous series of polystyrene (PS), poly(2‐vinyl‐naphthalene) (P2VN), and poly(9‐vinyl‐phenanthrene) (P9VPh). The DSC results show that the miscibility of PCBM in these polymers increases nonlinearly from 16.5 wt % in PS, 57.0 wt % in P2VN, and 74.9 wt % in P9VPh. The SANS results show that at all concentrations of PCBM, the blends are composed of two mixed phases. Analysis shows that the phase dimensions remain largely independent of PCBM content, but there is a strong dependence of the PCBM concentration difference in the two phases with increasing PCBM content. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 994–1001     

Conductivity and characterization of polyurea electrolytes with carboxylic acid

Polyurea, which was synthesized from 4,4′‐diphenylmethane diisocyanate, Jeffamine‐ED2001 (weight‐average molecular weight: 2000), and 3,5‐diaminobanzoic acid (DABA) were doped with lithium perchlorate (LiClO₄) as the polyelectrolyte. Differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, and ⁷Li magic‐angle spinning (MAS) solid‐state NMR were used to monitor changes in the morphology of polyurea electrolytes corresponding to the concentration of LiClO₄ dopants. DSC showed the glass‐transition temperature of the hard and soft segments increases with salt concentration. FTIR indicated the carboxylic group of DABA coordinates with the Li⁺ ion, and the ordered hydrogen‐bonded urea carbonyl groups are destroyed when the salt concentration exceeds 0.5 mmole of LiClO₄ (gPUrea)^?1. The ⁷Li MAS solid‐state NMR investigation of the polyurea electrolytes revealed the presence of two Li⁺ environments at lower temperature. Impedance spectroscopy measurements showed that the conductivity behavior followed the Arrhenius equation, and the maximum conductivity occurred when the crystalline structure of polyurea was disrupted. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 4007–4016, 2003     

Miscibility and surface properties of fluorinated copolymer blends involving hydrogen‐bonding interactions

The miscibility and underlying hydrogen‐bonding interactions of blends of a fluorinated copolymer containing pyridine and a nonfluorinated copolymer containing methacrylic acid were studied with differential scanning calorimetry (DSC), transmission Fourier transform infrared (TX‐FTIR) spectroscopy, and X‐ray photoelectron spectroscopy (XPS), whereas the surface properties of the blends were investigated with contact‐angle measurements, time‐of‐flight secondary‐ion mass spectroscopy, XPS, and attenuated total reflectance Fourier transform infrared spectroscopy. DSC studies showed that the presence of a sufficient amount of 4‐vinylpyridine units in the fluorinated copolymer produced miscible blends with the nonfluorinated copolymer containing methacrylic acid. TX‐FTIR and XPS showed the existence of pyridine–acid interpolymer hydrogen‐bonding interactions. Even though the anchoring effect of hydrogen bonding hindered the migration of the fluorinated component to the blend surface, it could not completely eliminate the surface enrichment of the fluorinated component and the surface rearrangement of the fluorinated pendant chain. The air–blend interface was mainly occupied by the fluorinated pendant chain, and the surface energies of the blends were extremely low, even with only 1.5 wt % of the fluorinated component in the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1145–1154, 2004     

Diphenol miscibility effect on the immiscible polyester/polyether binary blends through intermolecular hydrogen‐bonding interaction

Miscibility and hydrogen bonding interaction have been investigated for the binary blends of poly(butylene adipate‐co‐44 mol % butylene terephthalate)[P(BA‐co‐BT)] with 4,4'‐thiodiphenol (TDP) and poly(ethylene‐ oxide)(PEO) with TDP; and the ternary blends of P(BA‐co‐BT)/PEO/TDP by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The DSC results indicated that the binary blends of P(BA‐co‐BT)/TDP and PEO/TDP were miscible because each blend showed only one composition‐dependent glass‐transition over the entire range of the blend composition. The formation of intermolecular hydrogen bonds between the hydroxyl groups of TDP and the carbonyl groups of P(BA‐co‐BT), and between the hydroxyl groups of TDP and the ether groups of PEO was confirmed by the FTIR spectra. According to the glass‐transition temperature measured by DSC, P(BA‐co‐BT) and PEO, their binary blends were immiscible over the entire range of blend composition, however, the miscibility between P(BA‐co‐BT) and PEO was enhanced through the TDP‐mediated intermolecular hydrogen bonding interaction. It was concluded that TDP content of about 5–10% may possibily enhance miscibility between P(BA‐co‐BT) and PEO via a hydrogen bonding interaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2971–2982, 2004     

Supramolecular poly(ether ketone)–polyisobutylene pseudo‐block copolymers

The association behavior of telechelic hydrogen‐bonded poly(ether ketone) (PEK) and polyisobutylene (PIB) polymers and the formation of a new class of pseudo‐block copolymers is reported. The attachment of complementing hydrogen bonds (thymine/2,6‐diaminotriazine and cytosine/2,6‐diaminotriazine) onto the respective PIB and PEK polymers leads to a dramatic increase in the miscibility between the normally immiscible PEK and PIB polymers. The structure formation in the liquid state was studied by dynamic NMR spectroscopy as well as in the solid state via solid‐state NMR‐spectroscopy, DSC, and TEM methods. The polymers form a nanophase structure with a periodicity of 70 nm with the microphase separation occurring specifically within the donor–acceptor pair with the higher binding constant (thymine/2,6‐diaminotriazine) and not within the weaker bonded cytosine/2,6‐diaminotriazine pair. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 162–172, 2004     

Synthesis and characterization of a vinyl‐terminated benzoxazine monomer and its blends with poly(ethylene oxide)

A vinyl‐terminated benzoxazine (VB‐a), which could be polymerized through ring‐opening polymerization, was synthesized through the Mannich condensation of bisphenol A, formaldehyde, and allylamine. This VB‐a monomer was then subjected to blending with poly(ethylene oxide) (PEO), followed by thermal curing, to form poly(VB‐a)/PEO blends. The specific interactions, miscibility, morphology, and thermal properties of these blends were investigated with Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). Before curing, we found that PEO was miscible with VB‐a, as evidenced by the existence of a single composition‐dependent glass transition temperature (T_g) for each composition. The FTIR spectra revealed the presence of hydrogen‐bonding interactions between the hydroxyl groups of poly(VB‐a) and the ether groups of PEO. Indeed, the ring‐opening reaction and subsequent polymerization of the benzoxazine were facilitated significantly by the presence of PEO. After curing, DMA results indicated that the 50/50 poly(VB‐a)/PEO blend exhibited two values of T_g: one broad peak appeared in the lower temperature region, whereas the other (at ca. 327 °C, in the higher temperature region) was higher than that of pristine poly(VB‐a) (301 °C). The presence of two glass transitions in the blend suggested that this blend system was only partially miscible. Moreover, SEM micrographs indicated that the poly(VB‐a)/PEO blends were heterogeneous. The volume fraction of PEO in the blends had a strong effect on the morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 644–653, 2007     

Synthesis and characterization of polycyanurate/montmorillonite nanocomposites

The advantages of cyanate esters (CEs) versus competitor systems such as epoxies and polyimides, as well as the great reinforcing potential of organoclays properly dispersed into a polymeric matrix, have been examined in a series of polycyanurate (PCN)/montmorillonite (MMT) nanocomposites prepared under appropriate polymerization conditions. The curing schedule applied resulted in gradual propagation of polymerization. Through this procedure, the intragallery curing rate becomes comparable to the extragallery one, allowing intercalation before gelation. Systems with clay loadings from 1 to 3% per weight were synthesized, and their morphology and mechanical properties were studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM), wide angle X‐ray scattering (WAXS), dynamic mechanical analysis (DMA), and tensile tests. Microscopy investigations revealed better dispersion for the 3 wt % system compared to smaller concentrations, in which aggregation and, in some cases, agglomeration were the conspicuous features. Roughness and area analyses revealed more homogeneous dispersion for this nanocomposite. Topology and 3D‐phase images further suggested considerable reduction of the average particle diameters. WAXS analysis showed that the interlayer spacing of nanocomposites was increased compared to pristine MMT, indicating the formation of intercalated structures. On the other hand, tensile strength and elongation at break values displayed abrupt diminution with MMT addition, while Young's modulus exhibited a slight but systematic increment with MMT content. The decreasing glass transition tendency observed for small clay loadings was reversed in the case of 3 wt %, while secondary transitions were practically unaffected by the presence of MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1036–1049, 2008     

Partial miscibility in a nylon‐6/nylon‐66 blend coalesced from their common α‐cyclodextrin inclusion complex

We successfully formed a series of inclusion complexes (ICs) between an α‐cyclodextrin (α‐CD) host and two kinds of guest polymers, nylon‐6 and nylon‐66. An attempt to achieve an intimate blend between nylon‐6 and nylon‐66 through the formation and dissociation of their common α‐CD IC was made. The formation of all nylon ICs was verified with wide‐angle X‐ray diffraction, differential scanning calorimetry (DSC), and Fourier transform infrared (FTIR) and cross‐polarized/magic‐angle‐spinning ¹³C NMR spectroscopy. The experimental results demonstrated that α‐CD could only host single nylon polymer chains in the IC channels, either nylon‐6 or nylon‐66 in their own complexes, and presumably either nylon in neighboring channels of their common IC. The IC‐coalesced blend of nylon‐6 and nylon‐66 was obtained after the removal of the host cyclodextrin from their common IC with dimethyl sulfoxide. The spectroscopic results (FTIR and ¹³C NMR) illustrated that there was a degree of intimate miscibility existing in the IC‐coalesced blend, but not in the solution‐cast physical blend, although X‐ray diffraction patterns showed that the crystal structure of the IC‐coalesced blend was similar to that of the physical blend. DSC thermal profiles suggested that nylon‐66 first formed crystals during coalescence and that the subsequent crystallization of nylon‐6 was greatly affected by the nylon‐66 crystallites because of the close proximity of the two components in portions of the coalesced blend. DSC observations also demonstrated that the melting of the coalesced blend did not lead to complete phase separation of the nylon‐6 and nylon‐66 components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1369–1378, 2004     

Miscible blends of poly(vinyl phenyl ketone) and poly(4‐vinyl phenol)

An analysis by differential scanning calorimetry, modulated differential scanning calorimetry, and Fourier transform infrared spectroscopy (FTIR) indicates that blends of poly(vinyl phenyl ketone) (PVPhK) and poly(4‐vinyl phenol) (P4VPh) are miscible at ambient temperature. Miscibility, ascertained, is supported by the existence of a single glass transition for each composition of the PVPhK/P4VPh blends. The FTIR spectroscopy analysis demonstrates the formation of hydrogen bonds between carbonyl groups of PVPhK and hydroxyl groups of P4VPh. This specific interaction has a crucial role on the miscibility behavior of PVPhK/P4VPh blends. The evolution of the glass transition of the PVPhK, P4VPh, and its blends as a function of mixture composition shows negative deviations with to respect to the ideal mixing rule, and both Fox and Gordon–Taylor equations predict this behavior successfully. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2404–2411, 2006     

A polymer of bisphenol A and bisphenol A diglycidyl ether and its blends with poly(styrene‐co‐acrylonitrile): In situ polymerization preparation,morphology, and mechanical properties

The poly(hydroxy ether of bisphenol A)‐based blends containing poly(acrylontrile‐co‐styrene) (SAN) were prepared through in situ polymerization, i.e., the melt polymerization between the diglycidy ether of bisphenol A (DGEBA) and bisphenol A in the presence of poly(acrylontrile‐co‐styrene) (SAN). The polymerization reaction started from the initial homogeneous ternary mixture of SAN/DGEBA/bisphenol A, and the phenoxy/SAN blends with SAN content up to 20 wt % were obtained. Both the solubility behavior and Fourier transform infrared (FTIR) spectroscopy studies demonstrate that no intercomponent reaction occurred in the reactive blend system. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electronic microscopy (SEM) were employed to characterize the phase structure of the as‐polymerized blends. All the blends display the separate glass transition temperatures (T_g's); i.e., the blends were phase‐separated. The morphological observation showed that all the blends exhibited well‐distributed phase‐separated morphology. For the blends with SAN content less than 15 wt %, very fine SAN spherical particles (1–3 μmm in diameter) were uniformly dispersed in a continuous matrix of phenoxy and the fine morphology was formed through phase separation induced by polymerization. Mechanical tests show that the blends containing 5–15 wt % SAN displayed a substantial improvement of tensile properties and Izod impact strength, which were in marked contrast to those of the materials prepared via conventional methods. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 525–532, 1999     

Thermal and mechanical properties of a dendritic hydroxyl‐functional hyperbranched polymer and tetrafunctional epoxy resin blends

Blends of a tetrafunctional epoxy resin, tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM), and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 3,3′‐diaminodiphenyl sulfone (DDS) as curing agent. The phase behavior and morphology of the DDS‐cured epoxy/HBP blends with HBP content up to 30 phr were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The phase behavior and morphology of the DDS‐cured epoxy/HBP blends were observed to be dependent on the blend composition. Blends with HBP content from 10 to 30 phr, show a particulate morphology where discrete HBP‐rich particles are dispersed in the continuous cured epoxy‐rich matrix. The cured blends with 15 and 20 phr exhibit a bimodal particle size distribution whereas the cured blend with 30 phr HBP demonstrates a monomodal particle size distribution. Mechanical measurements show that at a concentration range of 0–30 phr addition, the HBP is able to almost double the fracture toughness of the unmodified TGDDM epoxy resin. FTIR displays the formation of hydrogen bonding between the epoxy network and the HBP modifier. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 417–424, 2010     

Intercalated poly(vinylidene fluoride)/clay nanocomposites: Structure and properties

The preparation and characterization of melt‐intercalated poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported. Organophilic clay (clay treated with dimethyl dihydrogenated tallow quaternary ammonium chloride) was used for the nanocomposite preparation. The composites were characterized with X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). XRD results indicated the intercalation of the polymer in the interlayer spacing. The incorporation of clay in PVDF resulted in the β form of PVDF. DSC nonisothermal curves showed an increase in the melting and crystallization temperatures along with a decrease in crystallinity. Isothermal crystallization studies show an enhanced rate of crystallization with the addition of clay. DMA indicated significant improvements in the storage modulus over a temperature range of ?100 to 150 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 31–38, 2003