Phase separation,porous structure,and cure kinetics in aliphatic epoxy resin containing hyperbranched polyester

Thermosetting blends of an aliphatic epoxy resin and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 4,4′‐diaminodiphenylmethane (DDM) as the curing agent. The phase behavior and morphology of the DDM‐cured epoxy/HBP blends with HBP content up to 40 wt % were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The cured epoxy/HBP blends are immiscible and exhibit two separate glass transitions, as revealed by DMA. The SEM observation showed that there exist two phases in the cured blends, which is an epoxy‐rich phase and an HBP‐rich phase, which is responsible for the two separate glass transitions. The phase morphology was observed to be dependent on the blend composition. For the blends with HBP content up to 10 wt %, discrete HBP domains are dispersed in the continuous cured epoxy matrix, whereas the cured blend with 40 wt % HBP exhibits a combined morphology of connected globules and bicontinuous phase structure. Porous epoxy thermosets with continuous open structures on the order of 100–300 nm were formed after the HBP‐rich phase was extracted with solvent from the cured blend with 40 wt % HBP. The DSC study showed that the curing rate is not obviously affected in the epoxy/HBP blends with HBP content up to 40 wt %. The activation energy values obtained are not remarkably changed in the blends; the addition of HBP to epoxy resin thus does not change the mechanism of cure reaction of epoxy resin with DDM. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 889–899, 2006     

Reaction‐induced phase separation in epoxy/polysulfone/poly(ether imide) systems. II. Generated morphologies

Epoxy–aromatic diamine formulations are simultaneously modified with two immiscible thermoplastics (TPs), poly(ether imide) (PEI) and polysulfone (PSF), in concentrations ranging from 5 to 15 wt %. The epoxy monomer is based on diglycidyl ether of bisphenol A and the aromatic diamines (ADs) are either 4,4′‐diaminodiphenylsulfone (DDS) or 4,4′‐methylenebis(3‐chloro 2,6‐diethylaniline) (MCDEA). Using phase diagrams developed in Part I of this series, thermal cycles are selected to generate different morphologies. It is found that, whatever the AD employed, a particulate morphology is obtained when curing blends that are initially homogeneous. In the case of DDS‐cured blends, a unimodal particle size distribution of PSF and PEI dispersed in a continuous epoxy‐rich phase is observed. By contrast, the MCDEA‐cured blends show a bimodal particle size distribution for all PSF/PEI relations that are analyzed. A completely different morphology, characterized by a distribution of irregular TP‐rich domains dispersed in an epoxy‐rich phase (double phase morphology), is obtained when curing blends that are initially immiscible. An X‐ray analysis of the different phases makes it possible to determine their qualitative composition. The dynamic mechanical behavior of fully cured blends is also discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3964–3975, 2004     

Evaluation of solubility parameters during polymerisation of amine‐cured epoxy resins

A new procedure for the calculation of solubility parameter evolution during polymerisation has been developed for amine‐cured epoxy systems, which allows quantitative thermodynamic modelling of chemically induced phase separation (CIPS). Solubility parameters calculation, chemical analysis based on near infrared spectroscopy and curing kinetics results obtained by differential scanning calorimetry will allow to model the evolution of the Flory–Huggins interaction parameter in amine‐cured epoxy blends. The resin system investigated was based on a diglycidyl ether bisphenol A (DGEBA) epoxy resin cured with isophorone diamine (IPD) blended with various reactive epoxydised dendritic hyperbranched polymer modifiers (HBP), yielding a CIPS‐controlled morphology. The analysis showed the evolution of the different contributions to the solubility parameters to follow the polymerisation kinetics. The dispersive contribution had the highest value at all stages of polymerisation, but the hydrogen and polar contributions showed the largest variation. By evaluating the dynamic evolution of the solubility parameter components, the Flory–Huggins interaction parameter in the epoxy resin‐hyperbranched polymer blends has been modelled as a function of time. This procedure, combined with thermodynamic modelling, will enable to predict phase diagrams in CIPS thermosetting blends quantitatively. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1883–1892, 2000     

Diglycidyl ether of bisphenol‐A epoxy resin modified using poly(ether ether ketone) with pendent tert‐butyl groups

Bisphenol‐A‐based difunctional epoxy resin was modified with poly(ether ether ketone) with pendent tert‐butyl groups (PEEKT). PEEKT was synthesized by the nucleophilic substitution reaction of 4,4′‐difluoro benzophenone with tert‐butyl hydroquinone in N‐methyl‐2‐pyrrolidone. Blends with various amounts of PEEKT were prepared by melt‐mixing. All the blends were homogeneous in the uncured state. The glass transition temperature of the binary epoxy/PEEKT blends was predicted using several equations. Reaction‐induced phase separation was found to occur upon curing with a diamine 4,4′‐diaminodiphenyl sulfone. The phase morphology of the blends was studied using scanning electron microscopy. From the micrographs, it was found that PEEKT‐rich phase was dispersed in a continuous epoxy matrix. The domain size increased with the amount of PEEKT in the blends. The increase in domain size was due to the coalescence of the domains after phase separation. Dynamic mechanical analysis of the blends gave two peaks corresponding to epoxy‐rich phase and thermoplastic‐rich phase. The tensile strength and modulus of the blends remained close to that of the unmodified resin, while the flexural properties decreased with the addition of PEEKT to epoxy resin. The fracture toughness of the epoxy resin increased with the addition of PEEKT. Investigation of the fracture surfaces revealed evidences for local plastic deformation of the matrix, crack pinning, crack path deflection, and ductile tearing of PEEKT‐rich phase. Thermogravimetric analysis revealed that the initial decomposition temperature of the blends were close to that of the unmodified resin. Finally, the properties of the blends were compared with other modified PEEK/epoxy blends. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2481–2496, 2007     

Novel phthalazinone‐bearing tetrafunctional epoxy: Synthesis,characterization, and their toughening application for TGDDM system

A novel tetrafunctional epoxy (TEPZ) was synthesized by “one spot two steps” method, and the effects of solvents, reaction temperature, and mole ratios of reactants on the reaction conversion were systematically investigated. The results demonstrated that the solvents participating in the reaction were the most crucial factor for high conversions. After curing, TEPZ/4,4′‐diaminodiphenyl sulfone (DDS) system exhibited better thermal stability compared with famous N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenyl methane (TGDDM)/DDS analog. When TEPZ is blended with TGDDM/DDS, the initial decomposition temperature of TGDDM/TEPZ/DDS hybrid elevated from 348°C to 362°C. The storage modulus and the glass transition temperature were sensitive to curing procedure and concentration of DDS. While the system consisted of 100 phr TGDDM, 30 phr TEPZ, and 40 phr DDS, the storage modulus and glass transition temperature increased significantly compared with those of TGDDM/DDS, and the impact strength increased by 31.6% simultaneously. Such enhancement could be ascribed to the structural feature of phthalazinone in TEPZ, which formed stable interpenetrating networks during thermal cure procedure.     

Miscibility and cure kinetics studies on blends of bisphenol-A polycarbonate and tetraglycidyl-4,4′-diaminodiphenylmethane epoxy cured with an amine

Differential scanning calorimetry (DSC) has been applied to characterize the glass transition behavior of the blends formed by bisphenol-A polycarbonate (PC) with a tetrafunctional epoxy (tetraglycidyl-4,4′-diaminodiphenyl methane, TGDDM) cured with 4,4′-diaminodiphenylsulphone (DDS). A rare miscibility in the complete composition range has been demonstrated in these blends. Additionally, the blend morphology was examined using scanning electron microscopy (SEM) and a homogeneous single-phase PC/epoxy network has been observed in the blends of all compositions. Moreover, polycarbonate incorporation has been found to exert a distinct effect on the cure behavior of the epoxy blends. The cure reaction rates for the epoxy-PC blends were significantly higher due to the presence of PC. In addition, the cure mechanism of the epoxy blends was no longer autocatalytic. An n-th order reaction mechanism with n = 1.2 to 1.5 has been observed for the blends of DDS-cured epoxy with PC of various compositions studied using DSC. The proposed n-th order kinetic model has been found to describe well the cure behavior of the epoxy/PC blends up to the vitrification point. © 1995 John Wiley & Sons, Inc.     

Chemically induced phase separated morphologies in epoxy resin‐hyperbranched polymer blends

The morphology build‐up in toughened epoxy blends using reactive hyperbranched dendritic polymers (HBP) and amine‐cured epoxy resins has been investigated in the present work. By changing the processing conditions or the surface chemistry of the modifier, very different morphologies can be obtained, ranging from homogeneous blends to coarse two‐phase systems. The morphology characterised by electron and optical microscopy has been interpreted combining constitutive equations for phase separation and thermodynamic modelling of phase interactions. The latter model, based on the Flory‐Huggins lattice theory, was modified in order to take into account the addition reactivity of the HBP modifiers. This approach proved successful and can be used as a tool for final morphology prediction in any reactive blend formulation.     

Development of toughened bio‐based epoxy with epoxidized linseed oil as reactive diluent and cured with bio‐renewable crosslinker

In the current work, renewable resourced toughened epoxy blend has been developed using epoxidized linseed oil (ELO) and bio‐based crosslinker. Epoxidation of linseed oil was confirmed through FTIR and ¹H NMR spectra. The ELO bio‐resin was blended at different compositions (10, 20, and 30 phr) with a petroleum‐based epoxy (DGEBA) as reactive diluent to reduce the viscosity for better processibility and cured with cardanol‐derived phenalkamine to overcome the brittleness. The flow behavior of the neat epoxy and modified bio‐epoxy resin blend systems was analyzed by Cross model at low and high shear rates. The tensile and impact behavior studies revealed that the toughened bio‐epoxy blend with 20 to 30 phr of ELO showed moderate stiffness with much higher elongation at break 7% to 13%. Incorporation of higher amount of ELO (20 to 30 phr) increases enthalpy of curing without affecting peak temperature of curing. The thermal degradation behavior of the ELO based blends exhibits similar trend as neat epoxy. The higher intensity or broadened loss tangent curve of bio‐epoxy blends revealed higher damping ability. FE‐SEM analysis showed a rough and rippled surface of bio‐based epoxy blends ensuring effective toughening. Reduced viscosity of resin due to maximum possible incorporation of bio‐resin and use of phenalkamine as curing agent leads to an eco‐friendly toughened epoxy and can be useful for specific coating and structural application.     

Hydrogen bonding interactions,crystallization, and surface hydrophobicity in nanostructured epoxy/block copolymer blends

Hydrogen bonding interactions, phase behavior, crystallization, and surface hydrophobicity in nanostructured blend of bisphenol A‐type epoxy resin (ER), for example, diglycidyl ether of bisphenol A (DGEBA) and poly(ε‐caprolactone)‐block‐poly(dimethyl siloxane)‐block‐poly(ε‐caprolactone) (PCL–PDMS–PCL) triblock copolymer were investigated by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, transmission electron microscopy, small‐angle X‐ray scattering, and contact angle measurements. The PCL–PDMS–PCL triblock copolymer consisted of two epoxy‐miscible PCL blocks and an epoxy‐immiscible PDMS block. The cured ER/PCL–PDMS–PCL blends showed composition‐dependent nanostructures from spherical and worm‐like microdomains to lamellar morphology. FTIR study revealed the existence of hydrogen bonding interactions between the PCL blocks and the cured epoxy, which was responsible for their miscibility. The overall crystallization rate of the PCL blocks in the blend decreased remarkably with increasing ER content, whereas the melting point was slightly depressed in the blends. The surface hydrophobicity of the cured ER increased upon addition of the block copolymer, whereas the surface free energy (γ_s) values decreased with increasing block copolymer concentration. The hydrophilicity of the epoxy could be reduced through blending with the PCL–PDMS–PCL block copolymer that contained a hydrophobic PDMS block. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 790–800, 2010     

A flame‐retardant phosphate and cyclotriphosphazene‐containing epoxy resin: Synthesis and properties

A novel flame‐retardant epoxy resin, (4‐diethoxyphosphoryloxyphenoxy)(4‐glycidoxyphenoxy)cyclotriphosphazene (PPCTP), was prepared by the reaction of epichlorohydrin with (4‐diethoxyphosphoryloxyphenoxy)(4‐hydroxyphenoxy)cyclotriphosphazene and was characterized by Fourier transform infrared, ³¹P NMR, and ¹H NMR analyses. The epoxy resin was further cured with diamine curing agents, 4,4′‐diaminodiphenylmethane (DDM), 4,4′‐diaminodiphenylsulfone (DDS), dicyanodiamide (DICY), and 3,4′‐oxydianiline (ODA), to obtain the corresponding epoxy polymers. The curing reactions of the PPCTP resin with the diamines were studied by differential scanning calorimetry. The reactivities of the four curing agents toward PPCTP were in the following order: DDM > ODA > DICY > DDS. In addition, the thermal properties of the cured epoxy polymers were studied by thermogravimetric analysis, and the flame retardancies were estimated by measurement of the limiting oxygen index (LOI). Compared to a corresponding Epon 828‐based epoxy polymer, the PPCTP‐based epoxy polymers showed lower weight‐loss temperatures, higher char yields, and higher LOI values, indicating that the epoxy resin prepared could be useful as a flame retardant. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 972–981, 2000     

Reactive compatibilization of polyamide‐6 (PA 6)/polybutylene terephthalate (PBT) blends by a multifunctional epoxy resin

A multifunctional epoxy resin has been demonstrated to be an efficient reactive compatibilizer for the incompatible and immiscible blends of polyamide‐6 (PA 6) and polybutylene terephthalate (PBT). The torque measurements give indirect evidence that the reaction between PA and PBT with epoxy has an opportunity to produce an in situ formed copolymer, which can be as an effective compatibilizer to reduce and suppress the size of the disperse phase, and to greatly enhance mechanical properties of PA/PBT blends. The mechanical property improvement is more pronounced in the PA‐rich blends than that in the PBT‐rich blends. The fracture behavior of the blend with less than 0.3 phr compatibilizer is governed by a particle pullout mechanism, whereas shear yielding is dominant in the fracture behavior of the blend with more than 0.3 phr compatibilizer. As the melt and crystallization temperatures of the base polymers are so close, either PA or PBT can be regarded as a mutual nucleating agent to enhance the crystallization on the other component. The presence of compatibilizer and in situ formed copolymer in the compatibilized blends tends to interfere with the crystallization of the base polymers in various blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 23–33, 2000     

Cure behavior and thermal stability of an epoxy: new bismaleimide blends for composite matrices

A new bismaleimide (BMI) resin was synthesized to formulate epoxy(tetraglycidyl diaminodiphenyl methane; TGDDM) – bismaleimide thermoset blends for composite matrix applications. 4,4′-diaminodiphenyl methane (DDM) was used as an amine curing agent for the TGDDM. A Fourier transform infrared (FTIR) spectroscopy was employed to characterize the new BMI resin. Cure behavior of the epoxy–BMI blends was studied using a differential scanning calorimeter (DSC). DSC thermograms of the thermoset blends indicated two exothermic peaks. The glass transition temperature of the thermoset blends decreased with BMI content. Thermogravimetric analysis (TGA) was carried out to investigate thermal degradation behavior of the cured epoxy–BMI thermoset blends. The new BMI resin reacted partially with the DDM and weak intercrosslinking polymer networks were formed during cure of the thermoset blends.     

Effect of fluorine functional groups on surface and mechanical interfacial properties of epoxy resins

To improve the surface and mechanical interfacial properties of epoxy resins, fluorine-containing epoxy resin (FEP) was prepared and blended with a commercially available tetrafunctional epoxy resin (TGDDM). As a result, when the fluorine content increased, the total surface energy of TGDDM/FEP blends was gradually decreased, while the water repellency of the blends was increased. The glass transition temperature and thermal stability factors of the blends showed maximum values at 20-40 wt% FEP compared with neat TGDDM epoxy resins. And the mechanical interfacial properties of the blend specimens were significantly increased with increasing the FEP content, which could be attributed to the intermacromolecular interactions in the cured TGDDM/FEP blends. These results indicate that the water repellency and toughness improvements have been achieved without significantly deterioration of the thermal properties in the TGDDM/FEP blends.     

Properties of tetra-N-glycidyl-4,4′-diamino diphenyl methane (TGDDM) cured thick films

Thick films of tetra-N-glycidyl epoxy resin of p,p′-diaminodiphenyl methane (TGDDM) were prepared using p,p′-diaminodiphenyl methane (DDM), p,p′-diaminodiphenyl sulfone (DDS) and diethylene triamine (DETA) as curing agent with or without the epoxy fortifiers PGEHA and VCDRC (at 20 phr level). These thick films were used to evaluate various physical, mechanical, chemical resistant and dielectric properties.     

Phase behavior,crystallization, and morphology in thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin and poly(ϵ‐caprolactone)

Thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin (PEG‐ER) and poly(?‐caprolactone) (PCL) were prepared via an in situ curing reaction of poly(ethylene glycol) diglycidyl ether (PEGDGE) and maleic anhydride (MAH) in the presence of PCL. The miscibility, phase behavior, crystallization, and morphology of these blends were investigated. The uncured PCL/PEGDGE blends were miscible, mainly because of the entropic contribution, as the molecular weight of PEGDGE was very low. The crystallization and melting behavior of both PCL and the poly(ethylene glycol) (PEG) segment of PEGDGE were less affected in the uncured PCL/PEGDGE blends because of the very close glass‐transition temperatures of PCL and PEGDGE. However, the cured PCL/PEG‐ER blends were immiscible and exhibited two separate glass transitions, as revealed by differential scanning calorimetry and dynamic mechanical analysis. There existed two phases in the cured PCL/PEG‐ER blends, that is, a PCL‐rich phase and a PEG‐ER crosslinked phase composed of an MAH‐cured PEGDGE network. The crystallization of PCL was slightly enhanced in the cured blends because of the phase‐separated nature; meanwhile, the PEG segment was highly restricted in the crosslinked network and was noncrystallizable in the cured blends. The phase structure and morphology of the cured PCL/PEG‐ER blends were examined with scanning electron microscopy; a variety of phase morphologies were observed that depended on the blend composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2833–2843, 2004     

Synthesis of hydroxyl‐terminated poly(ether ether ketone) with pendent tert‐butyl groups and its use as a toughener for epoxy resins

Hydroxyl‐terminated poly(ether ether ketone) with pendent tert‐butyl groups (PEEKTOH) was synthesized by the nucleophilic substitution reaction of 4,4′‐difluorobenzophenone with tert‐butyl hydroquinone with potassium carbonate as a catalyst and N‐methyl‐2‐pyrrolidone as a solvent. Diglycidyl ether of bisphenol A epoxy resin was toughened with PEEKTOHs having different molecular weights. The melt‐mixed binary blends were homogeneous and showed a single composition‐dependent glass‐transition temperature (T_g). Kelley–Bueche and Gordon–Taylor equations gave good correlation with the experimental T_g. Scanning electron microscopy studies of the cured blends revealed a two‐phase morphology. A sea‐island morphology in which the thermoplastic was dispersed in a continuous matrix of epoxy resin was observed. Phase separation occurred by a nucleation and growth mechanism. The dynamic mechanical spectrum of the blends gave two peaks corresponding to epoxy‐rich and thermoplastic‐rich phases. The T_g of the epoxy‐rich phase was lower than that of the unmodified epoxy resin, indicating the presence of dissolved PEEKTOH in the epoxy matrix. There was an increase in the tensile strength with the addition of PEEKTOH. The fracture toughness increased by 135% with the addition of high‐molecular‐weight PEEKTOH. The improvement in the fracture toughness was dependent on the molecular weight and concentration of the oligomers present in the blend. Fracture mechanisms such as crack path deflection, ductile tearing of the thermoplastic, and local plastic deformation of the matrix occurred in the blends. The thermal stability of the blends was not affected by blending with PEEKTOH. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 541–556, 2006     

Synthesis of a new hyperbranched‐linear‐hyperbranched triblock copolymer and its use as a chemical modifier for the cationic photo and thermal curing of epoxy resins

A new hyperbranched‐linear‐hyperbranched polymer was prepared in a one pot process by reaction of 4,4‐bis(4‐hydroxyphenyl)valeric acid and poly(ethylene glycol) (HPH). After characterization by ¹H and ¹³C NMR, SEC, DSC, and TGA, this polymer was used, in proportions of 5, 10, and 15 phr, as a chemical modifier in the UV and thermal cationic curing of 3,4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexyl carboxylate epoxy resin. The curing process was studied by calorimetry, demonstrating the accelerating effect of the hydroxyl groups present in HPH's structure. The morphology of the resulting thermosets depended on the curing system used, as demonstrated by FE‐SEM microscopy, but in both cases phase separation occurred. Thermosets obtained by thermal curing presented lower thermal stability than UV‐cured materials. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Analysis of blends of poly(styrene‐co‐acrylonitrile) with an epoxy/aromatic amine resin using scanning thermal microscopy

Using a microthermal analyzer TA Instruments 2990 μTA, we have analyzed the morphologies developed for the resin tetraglycidyl‐4,4′‐diaminodiphenylmethane cured with an aromatic amine 4,4′‐diaminodiphenylsulphone modified with different amounts of poly(styrene‐co‐acrylonitrile) (SAN) thermoplastic. The phase‐separation phenomenon induced by polymerization was also followed by scanning electron microscopy. Using the modulated local thermal‐analysis mode of μTA, the glass‐transition temperatures of different domains for each sample were evaluated. Dynamic mechanical analyzer experiments were made to evaluate the macroscopic thermal properties of the blends. A morphology was well established for all blends examined with these techniques showing a nodular structure, the epoxy‐rich phase, and a continuous phase, the SAN‐rich phase, that forms the matrix. From both microscopic and macroscopic thermal analyses, it is concluded that a phase separation exists for the blends investigated. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 284–289, 2002     

Phase behavior and morphology in epoxy resin/poly(L-lactide) blends. Comparison with epoxy resin/poly(L,D-lactide) blends

Thermoset/thermoplastic blends were prepared with epoxy–aromatic diamine mixtures and poly(L-lactide) (PLLA), as semicrystalline thermoplastic, in concentrations ranging from 4 to 25 wt.%. In some cases, poly(L,D-lactide) (PDLLA), an amorphous thermoplastic, was used instead for comparative purposes. Diglycidyl ether of bisphenol-A (DGEBA) was employed as epoxy resin and 4,4′-diaminodiphenylmethane (DDM) as curing agent. Phase behavior and morphology were studied during curing at 140 °C. Initially, all blends were homogeneous; however, the curing reaction of the epoxy resin caused a liquid–liquid phase separation. A co-continuous morphology was formed at the beginning of the phase separation in all the considered blend compositions. Blends evolved to a particle/matrix structure or to a phase-inverted structure depending on the initial blend composition. At 140 °C, crystallization only occurred in blends with 16 and 25 wt.% PLLA. This crystallization originates changes in the surface of the epoxy-rich droplets developed with the phase separation.     

Kinetics studies on the accelerated curing of liquid crystalline epoxy resin/multiwalled carbon nanotube nanocomposites

A new class of nanocomposite has been fabricated from liquid crystalline (LC) epoxy resin of 4,4′‐bis(2,3‐epoxypropoxy) biphenyl (BP), 4,4′‐diamino‐diphenyl sulfone (DDS), and multiwalled carbon nanotubes (CNTs). The surface of the CNTs was functionalized by LC epoxy resin (ef‐CNT). The ef‐CNT can be blended well with the BP that is further cured with an equivalent of DDS to form nanocomposite. We have studied the curing kinetics of this nanocomposite using isothermal and nonisothermal differential scanning calorimetry (DSC). The dependence of the conversion on time can fit into the autocatalytic model before the vitrification, and then it becomes diffusion control process. The reaction rate increases and the activation energy decreases with increasing concentration of the ef‐CNT. At 10 wt % of ef‐CNT, the activation energy of nanocomposite curing is lowered by about 20% when compared with the neat BP/DDS resin. If the ef‐CNT was replaced by thermal‐insulating TiO₂ nanorods on the same weight basis, the decrease of activation energy was not observed. The result indicates the accelerating effect on the nanocomposite was raised from the high‐thermal conductivity of CNT and aligned LC epoxy resin. However, at ef‐CNT concentration higher than 2 wt %, the accelerating effect of ef‐CNTs also antedates the vitrification and turns the reaction to diffusion control driven. As the molecular motions are limited, the degree of cure is lowered. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011