侧链含邻苯二甲酰亚胺的聚酰亚胺液晶垂直取向剂的制备与表征

以邻苯二甲酰亚胺和溴代正辛烷为原料,合成了功能性二胺单体N-辛基-4(3,5-二氨基苯甲酰基)-氨基邻苯二甲酰亚胺(D8).用此单体与3,3’-二甲基-4,4’-二氨基二苯甲烷(DMMDA)、3,3’,4,4’-二苯醚四甲酸二酐(ODPA)共缩聚,采用低温缩聚-化学亚胺化方法,通过调节共聚物组成制备了5种聚酰亚胺(PI).利用FTIR、NMR、UV-Vis与DSC等手段对合成的二胺单体及聚酰亚胺进行了结构表征和性能测试;研究了其摩擦取向性能、透光性能、溶解性能和耐热性能.结果表明,5种聚酰亚胺均可溶于常见极性溶剂,如NMP、THF等;随着D8含量的增加,PI膜对液晶分子取向时的预倾角逐渐增大至垂直,当D8含量大于20%,且经过5次摩擦后,预倾角仍能保持在89°以上.此外实验所得PI透过率大于80%,玻璃化转变温度在260℃以上.     

不同比例的s-BPDA/i-BPDA型聚酰亚胺共聚结构与性能关系

由不同比例的二酐单体3,3′,4,4′-联苯四酸二酐(s-BPDA)/2,2′,3,3′-联苯四酸二酐(i-BPDA)与二胺单体4,4′-二氨基二苯醚(4,4′-ODA)制得了一系列共聚可溶聚酰亚胺. 采用DSC 、TGA和拉伸等测试方法对所得共聚聚酰亚胺进行了表征, 实验结果表明, 所得聚酰亚胺具有优异的力学性能和热稳定性, 并且随着i-BPDA含量的增加, 聚酰亚胺的溶解性提高, 玻璃化转变温度(Tg)升高, 中间体聚酰胺酸的固有黏度降低.     

含二氮杂萘酮结构磺化聚酰亚胺共聚物的合成及其膜性能研究

将磺化二胺单体4,4′-二(4-氨基苯氧基)联苯-3,3′-二磺酸(BAPBDS),含二氮杂萘酮结构的二胺1,2-二氢-2-(4-氨基苯基)-4-[4-(4-氨基苯氧基)-苯基]-二氮杂萘-1-酮(DHPZDA)和1,4,5,8-萘四甲酸二酐(NTDA)进行缩合聚合反应,通过改变磺化二胺单体BAPBDS的含量,合成了一系列不同磺化度的聚酰亚胺(SPIs).采用FT-IR,1H-NMR表征了聚合物的结构,热重分析仪(TGA)研究了聚合物的耐热稳定性.以间甲酚为溶剂,通过溶液浇铸法成膜研究了该系列聚合物膜的性能.结果表明,与其它磺化聚酰亚胺相比,该系列磺化聚酰亚胺的溶解性以及在高温下(80℃)水解稳定性有较大提高.     

含苯并咪唑单元可溶性聚酰亚胺的合成和性能

合成了一种刚性芳香二胺单体3,3',5,5'-四甲基-4,4'-二胺基苯基甲苯(BDAP),与6-氨基苯基-2-氨基苯并咪唑(BIA)组成混合二胺,分别与4种商品化的二酐单体(均苯四酸二酐(PMDA)、联苯四酸二酐(BPDA)、二苯酮四酸二酐(BTDA)和二苯醚四酸二酐(ODPA))一步法缩聚合成了一系列可溶性聚酰亚胺.采用FTIR,1H-NMR,UV-Vis,DMA和TGA等测试方法对所制备的聚酰亚胺进行了表征.结果表明,所制备的聚酰亚胺具有良好的溶解性能,能够在NMP和DMAc等常规溶剂中溶解;耐热性及力学性能优良,玻璃化转变温度超过410℃,分解温度在500℃以上.     

原位一步法制备BTDA/4,4′-ODA/4,4′-SDA聚酰亚胺表面银化薄膜

采用原位一步自金属化的方法制备了具有反射性和导电性的表面银(Ag)化的聚酰亚胺(PI)薄膜,PI是由一种二酐(3,3′,4,4′-四羧基二苯酮酐,BTDA)和两种二胺(4,4′-二氨基二苯醚,4,4′-ODA与4,4′-二氨基二苯硫醚,4,4′-SDA)三元共聚而得,系统研究了4,4′-SDA的引入对薄膜性能及相态结构的影响.结果表明,4,4′-SDA的加入有助于银的还原和迁移,并利于薄膜导电性的提高,薄膜的反射率在两种二胺单体4,4′-ODA与4,4′-SDA的摩尔比为1比1时达到最佳.     

原位一步法制备BTDA/4,4′-ODA/4,4′-SDA 聚酰亚胺表面银化薄膜

采用原位一步自金属化的方法制备了具有反射性和导电性的表面银(Ag)化的聚酰亚胺(PI)薄膜,PI是由一种二酐(3,3′,4,4′-四羧基二苯酮酐,BTDA)和两种二胺(4,4′-二氨基二苯醚,4,4′-ODA与4,4′-二氨基二苯硫醚,4,4′-SDA)三元共聚而得,系统研究了4,4′-SDA的引入对薄膜性能及相态结构的影响.结果表明,4,4′-SDA的加入有助于银的还原和迁移,并利于薄膜导电性的提高,薄膜的反射率在两种二胺单体4,4′-ODA与4,4′-SDA的摩尔比为1比1时达到最佳.     

一种可溶性聚酰亚胺的合成及其渗透汽化脱有机硫化物性能测试

由3,3′,4,4′-二苯醚四甲酸二酐(ODPA)和3,3′-二甲基4,4′二氨基二苯甲烷(DMMDA)二胺为单体,利用低温溶液缩聚化学亚胺化法合成了ODPA DMMDA聚酰亚胺.利用FT IR、NMR与DSC等手段对聚酰亚胺的结构进行了表征;研究了其溶解性能、耐热性能和力学性能.结果表明,此聚酰亚胺可溶于DMF、DMAc等极性溶剂;玻璃化转变温度为264℃,其10%的热分解温度为521℃;断裂强度为137MPa;断裂伸长率为18%.采用相转化法将其制成非对称膜,采用扫描电子显微镜(SEM)观察内部结构,在渗透汽化脱硫实验中,对噻吩有良好的选择透过性能.350K时,硫富集率为3.68,渗透通量为0.92kg m2h.     

3,5-二氨基苯甲酸-4′-联苯酯及含液晶侧链的聚酰亚胺的合成与表征

合成了含液晶基元侧基的二氨基化合物——— 3,5 二氨基苯甲酸 4′ 联苯酯 ,并以 3,3′ 4,4′ 二苯醚四羧酸二酐 (ODPA)、二氨基二苯醚 (ODA)为共聚单体 ,制备了具有液晶侧链原位复合自增强功能的新型聚酰亚胺 (PI)薄膜材料 .这种含液晶基元侧链的PI能溶解在极性非质子有机溶剂中 ,显示出良好的可加工性能 .由于液晶基元侧链的原位复合自增强作用 ,该类膜材料显示出良好的力学性能和热稳定性能在热台偏光显微镜下观察 ,该类聚合物在较高的温度区域内显示液晶行为 ,并呈现向列相织构     

含全氟环丁烷环可溶性聚酰亚胺的合成与表征

以乙酰氨基苯酚为原料,经过BrCF2CF2Br氟烷基化、Zn催化脱卤、热环化二聚,以及水解去保护,合成了一种含全氟环丁烷环的二胺单体1,2,3,3,4,4-六氟-1,2-双[4-(氨基)苯氧基]环丁烷.用该单体分别与酯环二酐双环[2·2·1]辛烷-2,3,5,6-四羧基2,3,5,6-二酐(BHDA)、芳香性二酐3,3′,4,4′-联苯四酸二酐(BPDA)和3,3′,4,4′-二苯酮四酸二酐(BTDA)通过“一步法”制备了3种新型含全氟环丁烷环聚酰亚胺.通过粘度测试、溶解性实验、FT-IR、热失重分析(TGA)和差热扫描量热(DSC)分析等手段,对所合成的聚酰亚胺的结构与性能进行了表征.结果显示该类聚酰亚胺可溶于大多数常用极性有机溶剂,热分解温度高于480℃,其中两种聚合物玻璃化温度低于150℃,表明含全氟环丁烷环聚酰亚胺具有良好的溶解性和可加工性.     

引入三氟甲基侧基对对苯醚型聚酰亚胺薄膜吸水性及水蒸汽透过性的影响

合成了3种含三氟甲基的芳香二胺,进而与3,3′,4,4′-联苯四甲酸二酐(BPDA)缩聚,得到3种对苯醚型含氟聚酰亚胺薄膜,并由4,4′-二氨基二苯醚（4,4′-ODA）与BPDA缩聚得到聚酰亚胺薄膜。 对4种聚酰亚胺薄膜的水蒸汽透过率、吸水性和热学性能的测试结果表明,其中聚合物PI-1（2,2′-BTF-4,4′-BADE+BPDA;BTF：双三氟甲基;BADE：二氨基二苯醚）的水蒸汽透过率为7.70 g/（h·m2）,吸水率为0.67%,玻璃化转变温度为259.74 ℃,质量损失5%的温度为521.40 ℃,具有良好的水蒸汽透过性和低吸水性。     

Ordered porous films based on fluorinated polyimide derived from 2,2′-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride and 3,3′-dimethyl-4,4′-diaminodiphenylmethane

One of fluorinated polyimides was synthesized from 2,2′-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride (6FDA) and 3,3′-dimethyl-4,4′-diaminodiphenylmethane (DMMDA) by two-steps method, which had good solubility and hydrophilicity. 6FDA-DMMDA polyimide was dissolved in chloroform (CHCl₃) and cast on a glass substrate in a humid atmosphere. It was found that 6FDA-DMMDA/CHCl₃ solution was easy to form ordered porous structure at high concentration, and the reason was discussed in detail. In addition, the influences of solution concentration, the atmosphere humidity, were also tested.     

Synthesis and Characterization of Soluble Polyimides Derived from 4,4′‐Diamino‐3,3′‐dimethyldiphenylmethane and Their Pervaporation Performances

Two kinds of soluble polyimides were synthesized from 4,4′‐diamino‐3,3′‐dimethyldiphenylmethane (DMMDA) and two dianhydrides (including BTDA, ODPA) via a two‐step method, low temperature solution polycondensation and next chemical imidization. All polyimides were readily soluble in common polar solvent, such as DMF, DMAc and NMP. The polyimides were characterized by FT‐IR, NMR, DSC, XRD and EA. The results showed that all of the polyimides revealed an amorphous nature and their inherent viscosities were 0.68–0.96 dlg^?1. The glass transition and melt temperature of these polyimides were determined by DSC and ranged from 224–283°C and 372–384°C, respectively. Thermogravimetric analysis indicated that these polyimides remained fairly stable up to a temperature around or below 400°C. Moreover, 10% mass losses were recorded at approximately 525°C in nitrogen atmosphere. They had a tensile strength in the range 89–137 MPa, and elongations breaking at around 10%. The pervaporation properties of the prepared polyimide dense membranes for ethanol/water mixtures were investigated at a different temperature and the average value of the separation factor and total permeation flux were 46–108 and 660–1380 g/m²h, respectively.     

Synthesis and characterisation of rubbing-resistant polyimides with naphthalimide side-chain for liquid-crystal alignment layers

A novel diamine with a side-chain containing naphthalimide ring and non-polar alkyl end group, N-octyl-4-(3,5-dinitrobenzoyl)-amido-1,8-naphthalimide (N8), was synthesised and its chemical structure was confirmed by FTIR (fourier transform infrared) spectroscopy and nuclear magnetic resonance spectroscopy (¹H-NMR). Then, a new family of polyimides (PIs) containing naphthalimide unit in the side-chains has been successfully synthesised by reaction of 4,4′-oxydiphthalic anhydride (ODPA) and 3,3′-dimethyl-4,4′-methylenediamine (DMMDA) with the novel functional diamine N8. The obtained polymers showed excellent solubility in a broad range of solvents, including tetrahydrofuran. Thermal properties of polymers were good enough to permit the use of these PIs on liquid-crystal displays (LCDs) applications. Alignment films obtained by casting offered outstanding rubbing-resistant ability, meanwhile kept the pretilt angle high above 89°. The PI seems to be prospective materials for alignment layers in LCDs.     

Thermal and hydrolytic stability of sulfonated polyimide membranes with varying chemical structure

Many important properties required for fuel cell applications including hydrolytic stability, depend on various factors like flexibility of the polymer backbone, ring structure and phase separation. This paper is primarily focused on studying the effect of the chemical backbone structure on the hydrolytic stability and other properties. To study the difference in the hydrolytic stability with change in the chemical backbone structure of sulfonated polyimides we synthesized phthalic sulfonated polyimides and naphthalenic sulfonated polyimides. Two series of phthalic sulfonated polyimides were prepared using 4,4′-oxydiphthalic anhydride (ODPA) and 4,4′-methylene dianiline (MDA), and 4,4′-(hexafluoroisopropylidine) diphthalic anhydride (6FDA) and oxydianiline (ODA). 4,4′-Diaminobiphenyl-2,2′-disulfonic acid (BDSA) was used to introduce sulfonic acid group into both series. Naphthalenic polyimides were synthesized from 1,4,5,8-naphthalenetetra-carboxylic dianhydride, BDSA, MDA and ODA. Also to observe other properties according to variation of sulfonic acid content, the degree of functionalisation was effectively controlled by altering the mole ratio between the sulfonated and non-sulfonated diamine monomers in phthalic sulfonated polyimides. The hydrolytic stability of the polyimides was followed by FT-IR spectroscopy at regular intervals. Polyimides prepared using naphthalenic dianhydride, NTDA, exhibited higher hydrolytic stability than the phthalic dianhydrides. The proton conductivity, ion exchange capacity (IEC) and water uptake measurements revealed the dependence on the molecular weight of the repeating unit. The proton conductivity of the sulfonated polyimides was found to vary with chemical backbone structure.     

Synthesis of soluble polyimides for vertical alignment of liquid crystal via one-step method

A series of polyimides (PIs) were copolymerized from 4-dodecyloxy-biphenyl-3′,5′-diaminobenzoate (DBPDA), 3,3′-dimethyl-4,4′-methylene-dianiline (DMMDA) and 4,4′-oxydi(phthalic anhydride) (ODPA) via one-step method. The PIs possessed excellent solubility in polar aprotic solvents and easily formed thin flexible films by solution casting. The glass-transition temperatures (T_gs) of the PIs were in the range of 219-242 °C and thermal decomposition temperatures in nitrogen occurred above 350 °C. The resultant PI films exhibited high transparency at wavelengths greater than 400 nm and induced excellent uniform vertical alignment of liquid crystal (LC). Even after the rubbing process, the pretilt angles of LC were still above 89°. The PI seems to be a prospective material for alignment layers in flexible displays.     

Preparation and properties of azopolyimides-I

A new class of aromatic and heterocyclic polyimides were synthesized from benzothiazoleamines benzidine, 4,4′-diaminodiphenyl ethane and 4,4′-diamino diphenyl sulfone with 4,4′-azodipthalic anhydride and/or pyromellitic dianhydride. The synthesis involved the reaction of the dianhydride with the respective diamine to yield an intermediate, soluble, open chain precursor polymer, the polyamic acid, which on cyclodehydration yielded the less soluble, heat resistant polyimides. All these polyimides were characterized by IR and NMR. Solubility, density, viscosity, and thermal stability of these polymers were also studied.     

PERVAPORATION SEPARATION FOR TOLUENE/n-HEPTANE MIXTURE BY POLYIMIDE MEMBRANES CONTAINING FLUORINE

Five kinds of polyimides were synthesized using five dianhydrides (including 2,2-bis[4-(3,4-dicarboxyphenoxy)- phenyl] propane dianhydride (BPADA),3,3',4,4'-diphenylsulfone-tetracarboxylic dianhydride (DSDA),4,4'- (hexafluoroisopropylidene)-diphthalic anhydride (6FDA),1,4-bis(3,4-dicarboxyphenoxy) benzene dianhydride (HQDPA), and 4,4'-oxydiphthlic dianhydride (ODPA)) and 2,2-bis[4-(4-aminophenoxy)phenyl] hexafluoropropane (BDAF) via the two- step method that included polyaddition to form the polyamic aci...     

Polyimides from isomeric diphenylthioether dianhydrides

3,3′,4,4′‐Diphenylthioether dianhydride (4,4′‐TDPA), 2,3,3′,4′‐diphenylthioether dianhydride (3,4′‐TDPA), and 2,2′,3,3′‐diphenylthioether dianhydride (3,3′‐TDPA) were synthesized from 3‐chlorophthalic anhydride and 4‐chlorophthalic anhydride. A series of polyimides derived from the isomeric diphenylthioether dianhydrides with several diamines were prepared. The properties, such as the solubility, thermal and mechanical behavior, dynamic mechanical behavior, wide‐angle X‐ray diffraction, and permeability to some gases, were compared among the isomeric polyimides. Both 3,3′‐TDPA‐ and 3,4′‐TDPA‐based polyimides had good solubility in polar aprotic solvents and phenols. The 5% weight loss temperatures of all the obtained polyimides was near 500 °C in nitrogen. The glass‐transition temperatures decreased according to the order of the polyimides based on 3,3′‐TDPA, 3,4′‐TDPA, and 4,4′‐TDPA. The 3,4′‐TDPA‐based polyimides had the best permeability and lowest permselectivity, whereas the 4,4′‐TDPA‐based polyimides had the highest permselectivity and the lowest permeability of the three isomers. Furthermore, the rheological properties of thermoplastic polyimide resins based on the isomeric diphenylthioether dianhydrides were investigated, and they showed that polyimide 3,4′‐TDPA/4,4‐oxydianiline had the lowest melt viscosity among the isomers; this indicated that the melt processibility had been greatly improved. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 959–967, 2006     

SYNTHESIS AND CHARACTERIZATION OF HIGHLY ORGANO-SOLUBLE POLYIMIDES BASED ON ALICYCLIC 1,8-DIMETHYL-BICYCLO[2.2.2]OCT-7- ENE-2,3,5,6-TETRACARBOXYLIC DIANHYDRIDE AND AROMATIC DIAMINES

Organo-soluble alicyclic polyimides (ALPIs) were synthesized from an alicyclic dianhydride, 1,8-dimethylbicyclo[2.2.2] oct-7-ene-2,3,5,6-tetracarboxylic dianhydride (DMEA) and several multialkyl-substituted 4,4′-diaminodiphenylmethane compounds, including 3,3′-dimethyl-4,4′-diaminodiphenyl methane (DMDA), 3,3′,5,5′-tetramethyl-4,4′-diaminodiphenyl methane (TMDA) and 3,3′,5,5′-tetraethyl-4,4′-diaminodiphenylmethane (TEDA). For comparison, the aromatic polyimides (ARPIs) were synthesized from the aromatic dianhydride, 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) and the same diamines. The ALPIs exhibited better solubility and transparency,but worse thermal stabilities and mechanical properties than those of the ARPIs. And the ALPIs could be dissolved in common organic solvents, such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylformamide (DMF), N,N-dimethylacetamide (DMAc), chloroform, tetrahydrofuran, m-cresol and so on. The ALPI films had an UV-Vis cut-off at 320 nm and a transmittance of higher than 80% in the visible region. In addition, the ALPIs showed thermal decomposition temperatures (Td) of about 450℃, which was nearly 100℃ lower than that of the ARPIs.     

含氧膦结构的可溶性感光聚酰亚胺合成与表征

聚酰亚胺(PI)是一类综合性能优异的功能性材料,广泛应用于航天、航空及电子工业等领域[1].感光聚酰亚胺可以采用光刻工艺,大大简化了其应用加工程序[2,3],因而备受人们所青睐.含查尔酮结构的聚合物对UV辐射敏感度高和化学稳定性好,最近被广泛的研究和应用[4～7].主链含查尔酮结