亚硒酸钠在L-半胱氨酸自组装类生物膜修饰电极上的电化学行为

利用L-半胱氨酸自组装膜修饰金电极(L-Cys,Au/SAMs), 在0.05mol/L H_2SO_4 底液中研究了 Na_2SeO_3 的电化学特性.在0.00～1.30 V (vs. SCE) 电位范围内对微量Na_2SeO_3进行循环伏安扫描,发现L-Cys, Au/SAMs修饰电极在峰电位0.89 V处有灵敏的Se的氧化溶出峰.通过比较裸金电极和修饰电极在Na_2SeO_3 溶液中的电化学特性发现,修饰电极通过巯基中的S与Na_2SeO_3发生氧化还原作用生成Se,且修饰电极对沉积在电极表面的Se的氧化过程具有催化作用.根据Na_2SeO_3在单分子膜上的电化学行为,提出了单分子膜中硫(Au-S)与Se(Ⅳ)作用生成Se的反应机理、Se电化学催化氧化机理及巯基化合物通过生成纳米硒生物吸收Se的类生物膜模型.     

系列巯基苯基卟啉自组装膜的光谱和电化学性质

考察了系列巯基苯基卟啉自组装膜的光谱及电化学特征。 结果表明,与溶液中巯基苯基卟啉的光谱相比,自组装膜中卟啉分子的吸收和荧光光谱均发生了明显变化,随着卟啉分子中巯基数目的增加,其荧光峰依次发生红移;不同巯基苯基卟啉自组装膜修饰电极对电解液中电对的电子转移阻碍能力不同,由5,10-二[4-(3-巯基丙氧基)-苯基]-15,20二苯基卟啉形成的卟啉自组装膜的阻碍作用最强,膜表面覆盖度最致密。     

去甲肾上腺素在3-氨基-5-巯基-1,2,4-三唑修饰金电极上的电化学行为及研究

本文通过自组装的方法制备了3-氨基-5-巯基-1,2,4-三唑(TA)修饰金电极。X射线光电子能谱表明,3-氨基-5-巯基-1,2,4-三唑是通过形成S-Au键而组装到Au电极表面。研究了去甲肾上腺素在该自组装膜电极上的电化学行为。实验结果表明:在pH 4.5的0.1 mol/L BR缓冲溶液中,膜电极对去甲肾上腺素的电化学氧化具有明显的催化作用,其氧化峰电流与去甲肾上腺素的浓度在2.0×10-6~1.9×10-4mol/L范围内呈良好线性关系。方法检出限为4.0×10-7mol/L。     

生物素衍生物自组装膜制备及其覆盖度的电化学测定

利用循环伏安法和电化学交流阻抗谱研究了MBDA/Au,MBTA/Au,TBDA/Au,TBTA/Au修饰电极以及MBDA与DT混合自组装/Au、TBTA与DT混合自组装/Au修饰电极的覆盖度。结果表明这些自组装膜在金电极表面的覆盖度均比较高,达到99%以上;对同一类修饰电极,混合自组装膜的覆盖度高于单组分自组装膜的覆盖度,混合自组装体系的覆盖度随着DT比例的增加而增加;同类物质,长链化合物在金表面的覆盖度大于短链化合物,含二硫键的化合物与金电极的键合能力比含一个巯基的化合物键合能力强。     

维生素B_1自组装膜修饰金电极对多巴胺、尿酸的电催化作用

用维生素B1(VB1)在金电极上进行自组装,制备了VB1自组装膜修饰金电极(VB1-Au/SAMs/CME).利用循环伏安法初步研究了此自组装单分子膜修饰电极的电化学行为.结果表明: VB1在金电极表面具有特性吸附.以\3-/ 4-氧化还原电对为探针,考察了VB1自组装膜修饰金电极的电化学性质, VB1自组装膜的存在对\3-/4-的电子转移具有明显的阻碍作用.研究了多巴胺(DA)和尿酸(UA)在此电极上的电化学行为.实验结果表明, DA和UA在此电极上均可被电催化氧化.差分脉冲伏安(DPV)氧化峰电流与DA浓度在2.0×10-5～4.0×10-4 mol/L范围内呈线性关系;测定UA的线性范围为6.0×10-5～2.2×10-4 mol/L,而且可实现这两种物质的同时测定.     

Study on Electrochemical Behavior of Controllable Interface Alkanethiols Selfassembled Monolayers and Au Nanoparticles Modified Gold Electrode

在裸金电极上自组装不同比例的4,4’-二甲基联苯硫醇(MTP)和硫辛酸(TA)混合液,形成自组装膜( MTP+ TA/Au SAMs),再修饰纳米金,制得纳米金混合巯基修饰金电极(AuNPs/MTP+ TA/Au).研究了纳米金混合巯基修饰金电极的电化学行为和阻抗行为,结果表明电极表面pH值的改变对电极表面的电子转移有重要影响.对葡萄糖传感器的制备条件、测定条件、抗干扰能力等进行了讨论,结果表明修饰电极的微结构和微环境有必要进一步研究.     

界面可控硫醇SAMs纳米金修饰金电极的电化学行为研究

在裸金电极上自组装不同比例的4,4’-二甲基联苯硫醇(MTP)和硫辛酸(TA)混合液,形成自组装膜(MTP+TA/Au SAMs),再修饰纳米金,制得纳米金混合巯基修饰金电极(AuNPs/MTP+TA/Au)。研究了纳米金混合巯基修饰金电极的电化学行为和阻抗行为,结果表明电极表面pH值的改变对电极表面的电子转移有重要影响。对葡萄糖传感器的制备条件、测定条件、抗干扰能力等进行了讨论,结果表明修饰电极的微结构和微环境有必要进一步研究。     

细胞色素c在自组装纳米膜电极上的有效固定及直接电化学

采用自组装方法将壳聚糖-纳米金(Chi-Nano Au)修饰到金(Au)电极上,并经进一步自组装细胞色素c(Cyt c),制得自组装膜电极Cyt c/Chi-Nano Au/Au.测定了自组装膜电极的循环伏安曲线(CV)及稳定性.结果表明,利用自组装膜电极Chi-Nano Au/Au可以有效地固定Cyt c,并实现直接电子转移反应.Cyt c在0.13～0.28V(vs Ag/AgCl)之间显示一对明显的可逆氧化还原峰;峰电流与扫描速度呈现良好的线性关系,线性方程为Ipc=0.063 64+0.003 51υ,线性相关系数为r=0.997 2,这表明该电极过程受吸附控制.此外,所制备的膜电极稳定性良好.     

Au单晶表面氟表面活性剂FSN自组装膜的电化学行为

研究Au(111)和Au(100)表面非离子型氟表面活性剂FSN自组装膜的电化学行为.电化学扫描隧道显微术和循环伏安法测试表明,在0～0.8 V电位区间,FSN自组装膜未发生氧化还原,均一性好,可稳定地存在于电极表面,并显著抑制硫酸根离子在电极表面的吸附和Au单晶表面的重构.在FSN自组装膜Au单晶电极的初始氧化阶段,Au(111)表面有少量突起,而Au(100)表面呈现台阶剧烈变化,但FSN自组装膜的吸附结构没有改变.与Au(100)表面相比,Au(111)表面形成的FSN自组装膜可更有效地抑制Au表面的氧化.     

光催化还原制备Au/Ag核壳结构纳米粒子及其修饰电极的电催化性能

以Keggin结构硅钨杂多酸H4SiW12O40(SiW12)为光催化还原剂,通过光化学还原法制备Au/Ag核壳结构纳米粒子. 透射电子显微镜分析显示,所得纳米粒子粒径为30～40 nm,呈均匀分散的球形颗粒,该制备方法的特点是可以较好的避免单金属纳米粒子的形成. 将Au/Ag核壳纳米粒子修饰到具有PVP膜的玻碳电极表面,得到SiW12-(Au/Ag)-PVP多层膜修饰电极. 该修饰电极在0.5 mol/L H2SO4介质中具有良好的电化学响应,在0～-0.75 V电位范围内,出现了3对归属于SiW12的氧化还原峰,且电极性能稳定,灵敏度高. 对H2O2的电催化还原性能明显优于单金属Ag纳米粒子修饰电极,说明Au核的存在可以很好的改善Ag的电催化性能,Au和Ag之间存在相互协同催化作用.     

Self-assembled monolayer of an iron(III) porphyrin disulphide derivative on gold

A novel iron(III) porphyrin disulphide derivative have been successfully immobilised on gold surfaces by self-assembly. The redox response of the modified electrodes was compared with the obtained for a similar iron porphyrin in solution, confirming the immobilisation of the metalloporphyrin. The gravimetric data obtained by electrochemical quartz crystal microbalance (EQCM) during adsorption allowed an estimation of the electrode coverage, providing further evidence for the formation of the porphyrin SAM. The modified electrodes were also measured by conventional and imaging ellipsometry. The electrocatalytic activity of the two modified electrodes was tested for the reduction of the molecular oxygen.     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

Al Electrode Modified by Au Atoms as a Novel Electrode for Electrocatalytic Oxidation of Thiosulfate

An aluminum electrode modified with gold atoms was introduced as a novel electrode. Gold atoms were deposited both chemically and electrochemically onto the aluminum electrode to make an aluminum/gold (Al/Au) modified electrode (ME). The experimental results showed that the Al/Au modified electrode prepared by chemical deposition, exhibits much more current than the electrochemical deposition method. The electrochemical behavior of the Al/Au modified electrode was studied by cyclic voltammometry. This modified electrode showed two pairs of peaks, a₁c₁ and a₂c₂, with surface‐confined characteristics in a 0.5 M phosphate buffer. The dependence of E_pa of the second peak (a₂c₂) on pH shows a Nernestian behavior with a slope of 55 mV per unit pH. The effect of different supporting electrolytes, solution's pH and different scan rates on electrochemical behavior of Al/Au modified electrode was studied. Au deposited electrochemically on a Pt electrode (Pt/Au) was also used as another modified electrode. A comparative study of electrochemical behavior of bare Al, Pt/Au and Al/Au modified electrodes showed that both Pt/Au and Al/Au electrodes have the ability of electrocatalytic oxidation of S₂O₃^2?, but the electrocatalytic oxidation on the latter was better than the former. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry and chronoamperometry techniques. The average value of the rate constant for the catalytic reaction and the diffusion coefficient were evaluated by means of chronoamperometry technique.     

Electrochemical Studies of Chemically Modified Nanometer‐Sized Electrodes

Self‐assembled monolayers (SAMs) of 4‐aminothiophenol (4‐ATP) has been successfully deposited onto nanometer‐sized gold (Au) electrodes. The cyclic voltammograms obtained on a 4‐ATP SAMs modified electrode show peaks and the peak height is proportional to the scan rate, which is similar to that on an electroactive SAMs modified macro electrode. The electrochemical behavior and mechanism of outer‐sphere electron transfer reaction on the 4‐ATP SAMs modified nanometer‐sized electrode has also been studied. The 4‐ATP SAMs modified electrode is further modified with platinum (Pt) nanoparticles. Electrochemical behaviors show that there is electrical communication between Pt nanoparticles and Au metal on the Pt nanoparticles/4‐ATP SAMs/Au electrode. However, scanning electron microscopic image shows that the Pt nanoparticles are not evenly covered the electrode.     

Lightweight ITO Electrodes Decorated with Gold Nanostructures for Electrochemical Applications

Gold nanostructures were fabricated on a transparent indium tin oxide (ITO) coated PET substrate by an electrodeposition technique from a potassium gold (III) chloride solution for two different types of applications. It was found that the optical transparency of lightweight ITO electrodes could be maintained by depositing isolated gold nanostructures while opening up the use of these electrodes for inner sphere electron reactions, such as hydroquinone oxidation, which are not possible at ITO electrodes. For practical applications the adhesion of gold to the ITO electrode was improved by modifying the ITO surface with 3‐mercaptopropyl‐trimethoxysilane (MPS). Compared to Au/ITO, the Au/MPS/ITO electrode showed vastly improved electrochemical activity toward various electron transfer reactions when subjected to mechanical stress. The biosensing properties of the Au/MPS/ITO electrode was also investigated by studying the detection of immobilized DNA on the Au/MPS/ITO electrode via electrochemical impedance spectroscopy (EIS).     

An Electrochemical Sensing Platform for the Detection of Lead Ions Based on Dicarboxyl‐Calix[4]arene

A simple and highly sensitive electrochemical sensor COOH−C4 derived from dicarboxyl‐calix[4]arene modified on a screen printed gold electrode (Au) was developed for the determination of lead ions in water samples. A 3‐mercaptopropionic acid (MPA) monolayer was used as a template on the gold electrode for the surface modification with dicarboxyl‐calixarene. The modified electrodes were surface‐characterized using Fourier Transform infrared spectroscopy (FTIR). The data obtained proved the confirmation of each stage of the electrode modification. The electrochemical analyses of the COOH−C4 electrode showed an enhanced electrocatalytic activity and higher current towards Pb²⁺ ions as compared to the bare Au and MPA/Au electrodes. Under optimum conditions, the differential pulse voltammetry response of COOH−C4 displayed a wide linear response ranging from 280–2500 μg/L for Pb²⁺ with a detection limit of 6.2 μg/L. In addition, the fabricated electrode showed a high selectivity and stability towards the Pb²⁺ ions in presence of possible interfering species. The present method was successfully applied to determine Pb²⁺ ions in real samples with satisfactory precision, with a relative standard deviation of 3.12 % and an acceptable recovery of 92 %, which demonstrated the potential application of dicarboxyl‐calix[4]arene modified on electrodes for heavy‐metal sensing.     

纳米金–壳聚糖修饰电极循环伏安法测定抗坏血酸

介绍纳米金–壳聚糖修饰电极的制备方法及其测定抗坏血酸的分析应用。采用电沉积方法,将氯金酸与壳聚糖的混合电解液直接共沉积,制备了壳聚糖–纳米金修饰玻碳电极的电化学传感器。利用循环伏安法研究了抗坏血酸浓度、p H值等对抗坏血酸在修饰电极上的电化学行为的影响。实验结果表明,修饰电极对抗坏血酸具有良好的电催化氧化作用,抗坏血酸浓度在5×10~(–5)~1×10~(–3) mol/L范围内线性良好,回归方程为I_p=0.433 8c+0.881 9,相关系数为0.998 71。该法可指导纳米金–壳聚糖修饰电极的制备及抗坏血酸含量的测定。     

Enhanced Oxidation of Aldohexose and Aldopentose on Hg Adatom‐Modified Au Electrode in Alkaline Aqueous Solution

The electrochemical behavior of aldohexose and aldopentose monosaccharides was examined on Hg adatom‐modified and bare Au electrodes in alkaline aqueous solution using cyclic voltammetry. For the bare Au electrode, the oxidation peak currents are dependent on hydroxyl group configuration on the monosaccharides. On the other hand, for the Hg adatom‐modified Au electrode, the actual oxidation peak currents were similar for all monosaccharides other than glucose. Dispersion of Hg adatoms on the Au surface led to diminishment of configurational differences between monosaccharides as well as enhancement of oxidation peak current.     

Electrocatalytic Reduction of Oxygen at Glassy Carbon Electrodes Coated with Diazonium‐derived Porphyrin/Metalloporphyrin Films

In this study, the influence of the film structure was investigated on the electrocatalytic oxygen reduction at GC electrodes covered with porphyrin and metalloporphyrin rings via the diazonium modification method. For that purpose, primarily, tetraphenylporphyrin (TPP) films on GC electrode surfaces were prepared by electroreduction of in situ generated diazonium salts of 5‐(4‐aminophenyl)‐10,15,20‐triphenylporphyrin (APP) and 5,10,15,20‐tetrakis(4‐aminophenyl)porphyrin (TAPP) molecules. Next, the formation of metalloporphyrin films on the modified surfaces was accomplished through the complexation reactions of surface porphyrin rings with metal ions in the salt solutions containing Mn(II), Fe(III) and Co(II) ions. The resulting porphyrin and metalloporphyrin layers were identified with XPS and ICP‐MS. The electrochemical barrier properties of the films on GC surfaces were examined by cyclic voltammetry in K₃Fe(CN)₆ aqueous solution. The electrocatalytic abilities of the resulting films were also investigated for the oxygen electrochemical reduction by employing cyclic voltammetry in PBS solutions saturated with oxygen. The results showed that the oxygen reduction potentials on modified GC electrodes were shifted to less negative potentials compared to that of bare GC electrode. Also, it was obtained that the oxygen reduction reaction was more effective on the GC electrodes modified with TPP rings by using TAPP molecules than those prepared by using APP molecules.     

Electrochemical Detection of Catechol on Boron‐doped Diamond Electrode Modified with Au/TiO2 Nanorod Composite

Au/TiO₂ nanorod composites with different ratios of [TiO₂]:[Au] have been prepared by chemically reducing AuCl₄^‐ on the positively charged TiO₂ nanorods surface and used to modify boron‐doped diamond (BDD) electrodes. The electrochemical behaviors of catechol on the bare and different Au/TiO₂ nanorod composites‐modified BDD electrodes are studied. The cyclic voltammetric results indicate that these different Au/TiO₂ nanorod composites‐modified BDD electrodes can enhance the electrocatalytic activity toward catechol detection, as compared with the bare BDD electrode. Among these different conditions, the Au/TiO₂‐BDD3 electrode (the ratio of [TiO₂]:[Au] is 27:1) is the most choice for catechol detection. The electrochemical response dependences of the Au/TiO₂‐BDD3 electrode on pH of solution and the applied potential are studied. The detection limit of catechol is found to be about 1.4 × 10^‐6 M in a linear range from 5 × 10^‐6 M to 200 × 10^‐6 M on the Au/TiO₂‐BDD3 electrode.