铈锆氧化物固溶体对全钯三效催化剂性能的影响

铈锆氧化物固溶体对全钯三效催化剂性能的影响     

Ce0.1+xTi0.5-xAl0.2Y0.1La0.1O1.8材料的制备及在三效催化剂中的应用

采用共沉淀法制备了Ce0.1+xTi0.5-xAl0.2Y0.1La0.1O1.8(0≤x≤0.4)材料, 并对所制备的材料进行了X射线衍射(XRD)和X射线光电子能谱(XPS)的表征, 测定了材料的比表面积(BET法)和储氧量(OSC), 同时采用氢气程序升温还原(H2-TPR)和氨气程序升温脱附(NH3-TPD)研究了材料的还原性能和表面酸性. 研究结果表明, Ce/Ti摩尔比大于1∶2的材料能形成立方萤石结构的固溶体, Ce/Ti摩尔比为1时, 材料表面Ce4+/Ce3+摩尔比达到最大; 随着Ce/Ti摩尔比的增大, 材料的储氧能力先增大后减小, 而TPR还原峰温则是先减小后增大, 当Ce/Ti摩尔比为1时, 材料的储氧量达到最大, 为660 μmol/g; 还原峰峰温最低, 为616 ℃. 以制备的材料为载体制备了一系列Pt/Ce0.1+xTi0.5-xAl0.2Y0.1La0.1O1.8三效催化剂, 并对催化剂进行了活性评价. 活性测试结果表明, 以Ce/Ti比为1的载体材料制成的催化剂对C3H8, CO和NO的起燃温度分别为236, 147和228 ℃, 表现出了优异的温度特性.     

MnOx/Al2O3/Ce0.45Zr0.45M0.10Oy （M = Mn, Y, La） catalysts used for ethanol catalytic combustion

MnOx/Al2O3/Ce0.45Zr0.45M0.10Oy (M = Mn,Y,La) catalysts were prepared by impregnation method and characterized by BET,TPR and XRD analyses.The catalytic activities toward ethanol combustion were investigated in a microreactor.The results demonstrated that the catalytic activity of MnOx/Al2O3/Ce0.50Zr0.50O2 monolithic catalyst could be improved by doping Mn,Y and La into Ce0.50Zr0.50O2.When doping Y into Ce0.50Zr0.50O2,the catalyst MnOx/Al2O3/Ce0.45Zr0.45Y0.10O1.95 showed the highest activity.The 100% conversion temperature of ethanol was 230 ℃.Furthermore,once the conversion of ethanol started,the complete conversion was quickly achieved.The doping of Mn,Y and La led to better activity for ethanol combustion and lower temperature reduction peaks in TPR profiles.The doping of Mn resulted in enhanced oxygen storage capacity (OSC),larger area of the reduction peaks,and excellent reactivity,and the doping of Y resulted in the lowest reduction temperature and the best activity.     

Ce0.35Zr0.55La0.10O1.95对低贵金属Pt-Rh型三效催化剂性能的影响

采用共沉淀技术制备了Ce0.35Zr0.55La0.10O1.95固溶体, 其织构和结构性能以及氧化还原性能分别采用BET、XRD和程序升温(TP)技术进行了表征. 制备了低贵金属Pt-Rh型三效催化剂, 考察了Ce0.35Zr0.55La0.10O1.95对催化剂性能的影响. XRD和BET的结果表明, 经600 ℃焙烧5 h后, Ce0.35Zr0.55La0.10O1.95具有与Ce0.50Zr0.50O2相似的立方结构和高的比表面积；经1000 ℃焙烧5 h后, 仍能保持稳定的立方结构和47.25 m2•g−1的比表面积, 表现出优越的织构性能和高的热稳定性. H2-TPR和O2-TPO的结果表明, Ce0.35Zr0.55La0.10O1.95具有比Ce0.50Zr0.50O2更好的氧化还原性能. 和含Ce0.50Zr0.50O2的催化剂相比, 含Ce0.35Zr0.55La0.10O1.95的催化剂具有较宽的工作窗口, 优越的低温起燃性能, 较强的水气变换能力；催化剂经1000 ℃高温水热老化5 h后, 仍具有良好的催化活性, 表现出了优异的抗老化性能.     

纳米CeO2基固溶体催化柴油机碳颗粒物燃烧性能

采用柠檬酸溶胶鄄凝胶法制备CeO2基固溶体催化剂(Ce0.7Zr0.3O2-δ、Ce0.7Pr0.3O2-δ和Ce0.7Gd0.3O2-δ), 并考察了固溶体和三种常用载体(TiO2、SiO2和Al2O3)及其负载KNO3后的催化碳黑燃烧活性. 结果表明, CeO2基固溶体催化剂具有很高的催化燃烧活性, 其活性接近TiO2、SiO2和Al2O3负载30%KNO3催化剂的活性. 因为纳米CeO2基固溶体的形成, 提高了催化剂的抗烧结能力, 使氧更活泼, 从而提高氧化还原性能, 有利于碳颗粒燃烧. 由于CeO2基固溶体本身的高活性, 因此KNO3的添加不能明显提高CeO2基固溶体催化剂(尤其是Ce0.7Zr0.3O2-δ和Ce0.7Pr0.3O2-δ)的催化燃烧活性, 但KNO3能显著提高TiO2, SiO2和Al2O3的催化燃烧活性.     

胶溶法制备铈锆镧共改性氧化铝及催化性能

γ-Al2O3是机动车尾气净化催化剂的常用载体,其高温热稳定性、比表面积、孔容、孔径及表面酸性等对催化活性有很大影响.近年来,大量研究结果表明,铈、锆、镧和钡等元素的添加可以提高氧化铝的高温热稳定性和催化活性[1～3],然而这些研究大多致力于单组分或者双组分改性氧化铝,制备方法以浸渍法和溶胶-凝胶法为主.胶溶法制备三组分共同改性氧化铝的研究很少.本文利用胶溶法制备了系列铈、锆、镧改性氧化铝,讨论了三组分共同添加对氧化铝载体的性质以及催化剂活性的影响.     

Ce0.50Zr0.50O2中掺杂M(M = Mn,Y)对乙酸乙酯燃烧催化剂MnOx/Ce0.50-zZr0.50-zM2zOy/Al2O3性能的影响

考察了乙酸乙酯催化燃烧时,铈锆固溶体中掺杂M (M = Mn, Y)对催化剂MnO_x/Ce_0.50-zZr_0.50-zM_2zO_y/Al₂O₃活性的影响。结果表明: Mn的掺杂明显增加了储氧材料的储氧量(OSC),Y的掺杂明显降低了催化剂的还原温度;Mn 和Y的同时掺杂兼具Mn掺杂和Y掺杂的优点。催化剂MnO_x/Ce_0.40Zr_0.40Mn_0.10Y_0.10O_y/Al₂O₃ 性能最佳,完全转化温度为513K,且T_10% 和 T_100%间隔的温度范围最窄,可适用于较大初始浓度变化范围和较高空速(GHSV)条件下的乙酸乙酯净化。H₂程序升温还原(H₂-TPR)和X射线衍射(XRD)测试显示,MnO_x/Ce_0.40Zr_0.40Mn_0.10Y_0.10O_y/Al₂O₃具有较低的还原温度和较大的还原峰面积; Mn 和Y进入铈锆固溶体的晶格,改善了其织构性能,促进了锰氧化物在载体表面的分散。     

液相沉淀法制备稀土-锆固溶体及其性能研究

采用液相沉淀法制备了Ce0.6Zr0.3La0.05Y0.05O2固溶体。通过BET,XRD,SEM,程序升温还原和氧脉冲吸附等方法对合成产品性能进行了表征。研究了前驱体的形态、高温水热处理、表面处理以及后期固溶体的还原处理对固溶体性能的影响。其中前驱体的高温水热处理和固溶体的还原处理对固溶体的催化性能有很大的影响。200℃水热处理制得的固溶体经1000℃老化4 h后,比表面积为25.3 m2.g-1,孔容为0.21 cm3.g-1,经800℃还原处理3 h后储氧量为478.3μmol.g-1,显示了较高的比表面积和储氧能力的高温稳定性。     

Influence of CeO2 and La2O3 on properties of palladium catalysts used for emission control of natural gas vehicles

Pd/YZ-Al2O3 (Y and Zr modified Al2O3, and hereafter, labelled as Al) catalysts with 4 wt% additive CeO2 and/or La2O3 were prepared and characterized by X-ray photoelectron spectroscopy (XPS), NO-temperature programmed desorption (NO-TPD), N2-adsorption/desorption (Brunauer-Emmet-Teller BET method), X-ray diffraction (XRD) and CO-chemisorption. Catalytic activities for CH4, CO and NO conversion were tested in a gas mixture simulated the emissions from natural gas vehicles (NGVs) operated under stoichiometric conditions. The results indicated that all catalysts exhibited excellent catalytic performances for CH4 and CO oxidation and the promoting effect of CeO2 or La2O3 was significant for NO conversion. XPS results showed that the electron density around Pd was increased by CeO2 and/or La2O3, the binding energy of Pd 3d decreased as the order: Pd/Al>Pd/Ce/Al>Pd/La/Al>Pd/CeLa/Al. The electron-rich Pd showed Rh-like catalytic properties which exhibited good activity for the reduction of NO. NO-TPD results showed that the addition of CeO2 and/or La2O3 increased NO adsorption on surface, and promoted the conversion of NO.     

Ce0.6Zr0.35Y0.05O2和Pr0.6Zr0.35Y0.05O2催化剂表面上CO氧化和18O-16O交换反应的研究

测定了在Ce0.6Zr0.4O2,Ce0.6Zr0.35Y0.05O2,Pr0.6Zr0.4O2和Pr0.6Zr0.35Y0.05O2 (分别表示为CZ,CYZ,PZ和PYZ)样品表面上的CO氧化反应和18O-16O 同位素交换反应.结果表明: 在CZ和PZ系列固熔中掺杂Y3 离子可以改善晶格氧的迁移速度;PZ和PZY的晶格氧比CZ 和CZY 的晶格氧具有更高的氧化反应活性.其原因是将Y3 掺杂到Ce0.6Zr0.4O2 或Pr0.6Zr0.4O2晶格中,增加了样品的氧空位浓度,从而提高了晶格氧的迁移性质,而PrOx比CeO2具有更低温度的氧化还原性质,因此PZ和PZY的晶格氧比CZ 和CZY 的晶格氧具有更高的氧化反应活性.     

Catalytic methanol decomposition to carbon monoxide and hydrogen over Pd/CeO2-ZrO2-La2O3 with different Ce/Zr molar ratios

The catalytic behaviors of Pd (1.4 wt%) catalysts supported on CeO2-ZrO2-La2O3 mixed oxides with different Ce/Zr molar ratios were investigated for methanol decomposition. Nitrogen adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS), H2 temperature-programmed reduction (H2-TPR), X-ray diffraction (XRD) and Pd dispersion analysis were used for their characterization. Pd/Ce0.76Zr0.18 La0.06 O1.97 catalyst showed the highest BET surface area, best Pd dispersion capability and strongest metal-support interaction. Moreover, XPS showed that there was lattice defect oxygen or mobile oxygen. According to the result of O 1s measurements the lattice defect oxygen or mobile oxygen helped to maintain Pd in a partly oxidized state and increased the activity for methanol decomposition. The Pd/Ce0.76Zr0.18La0.06O1.97 catalyst exhibited the best activity. A 100% conversion of methanol was achieved at around 260℃, which was about 20-40 ℃ lower than other catalysts     

Pt/Ce0.6Zr0.4O2催化剂在水煤气变换反应中的电导研究

采用浸渍法制备了不同载体(Ce0.6Zr0.4O2,CeO2和ZrO2)负载的Pt基水煤气变换反应(WGSR)催化剂, 并对其进行了活性评价. 利用X射线衍射(XRD), 程序升温还原(TPR)和原位电导等技术对样品进行了表征. 结果表明, Ce0.6Zr0.4O2固溶体具有比CeO2更高的氧转移能力, 因此促进了Pt/Ce0.6Zr0.4O2催化剂的WGSR活性.     

负载型Pd三效催化剂：载体CeO2-ZrO2-BaO的制备及催化性能

制备了不同BaO含量的CeO2-ZrO2储氧材料,并以此材料为载体浸渍H2PdCl6制得三效催化剂.结果表明,不论新鲜还是1 000 ℃老化状态下,以10%BaO添加CeO2-ZrO2储氧材料制备的Pd三效催化剂活性最佳,起燃和完全转化温度最低.XPS结果证实,10%BaO添加.通过稳定PdO活性组分并改变其电子环境使得催化剂有最佳活性.而随着BaO含量持续增加,Pd活件组分相对处于较氧化状态.储氧量、低温N2吸附-脱附测试以及XRD测试结果均表明10%BaO添加的材料储氧量,比表面积以及孔容均最大,而且有适应三效催化的孔径.这些结果均有助于以其制备的Pd三效催化剂获得更好的活性以及热稳定性.     

单相Ce0.5Zr0.5O2立方固溶体的高压高温合成

以化学沉淀法制备的 Ce O2 和 Zr O2 纳米微粒为前驱体 ,首次在高压高温 (3 .1 GPa,1 0 73 K)下合成了单相 Ce0 .5Zr0 .5O2 面心立方固溶体 .使用 X射线衍射、TG-DTA、XPS、Raman、电子自旋共振谱和交流阻抗谱等对样品的结构、Ce离子的价态和导电性进行了表征 .实验结果表明 ,纳米 Ce O2 -50 % Zr O2 混合物在高压 (0 .9GPa以上 )高温 (1 0 73 K以上 )条件下可以发生固态反应 ,高压下固溶温度明显降低 .Ce0 .5Zr0 .5O2 面心立方固溶体在 773 K以下是热稳定的 ,不发生结构转变 ,固溶体中 Ce离子完全以 Ce4 + 形式存在 ,773 K退火也不引起 Ce4 + 向 Ce3 + 转变 ,晶格中氧缺位非常少 .Ce0 .5Zr0 .5O2 面心立方固溶体是离子导电 ,82 3 K时电导率 σ=1 .2× 1 0 -5S/cm,与纯 Ce O2 在同温度下的电导率同数量级 ;1 1 2 3 K时 σ=2 .1× 1 0 -3 S/cm,小于掺入稀土或碱土氧化物的氧化锆和氧化铈基电解质的电导率 .在高温区和低温区 ln(σT)与 1 /T的关系满足斜率不同的二条直线 ,低温活化能小于高温活化能 .固溶体的显微硬度 (50 g载荷 )为 572 HV.     

Pt/CexZr1-xO2催化剂上丙烷完全氧化性能研究

采用沉淀法制备了ZrO2,CeO2和Ce0.7Zr0.3O2载体,并用浸渍法制备负载型Pt催化剂。考察了500和900℃焙烧催化剂的丙烷完全氧化性能和水汽对丙烷氧化反应的影响。对于500℃焙烧的催化剂,催化剂的丙烷氧化活性顺序为:Pt/ZrO2-500>Pt/CeO2-500>Pt/Ce0.7Zr0.3O2-500;而经900℃焙烧的催化剂活性顺序为:Pt/ZrO2-900>Pt/Ce0.7Zr0.3O2-900>Pt/CeO2-900。反应气氛中水汽的存在对两种Pt/ZrO2催化剂的活性均有抑制作用(T50温度均提高了10~15℃);而对于Pt/CeO2-500催化剂有抑制作用(T50温度提高10℃),但对Pt/CeO2-900催化剂活性有促进作用(T50温度下降25℃);对于两种Pt/Ce0.7Zr0.3O2催化剂活性具有促进作用(T50温度均下降5~25℃)。表征结果表明催化剂的活性与其表面Pt物种价态密切相关,催化剂表面上Pt0物种有利于活性的提高。Pt/Ce0.7Zr0.3O2-500催化剂中只含有氧化态Pt物种(Pt^2+),而Pt/Ce0.7Zr0.3O2-900催化剂中则含有部分金属态Pt物种,因此其活性高于Pt/Ce0.7Zr0.3O2-500催化剂。     

Effects of Zr doping on stoichiometric and reduced ceria: a first-principles study

The Zr doping in CeO(2) may change the reduction properties and therefore the redox properties of CeO(2). Using first-principles density functional theory with the inclusion of on-site Coulomb interaction for a 96-atom supercell, these effects are studied by comparing the differences in atomic structures, electronic structures, and reduction energies of the doped CeO(2) and those of the nondoped CeO(2). It is found that (1) Zr doping of the ceria structure results in important modifications involving nonequivalent O atoms; (2) the oxygen anions (still four-coordinated) next to the doping center show considerably lower reduction energies (by 0.6 eV) and larger displacements ("higher mobilities"); (3) an O vacancy is most easily created close to the Zr centers, therefore the Zr-doping centers might serve as nucleation centers for vacancy clustering; and (4) the electrons left by the released oxygen localize on two Ce cations neighboring the vacancy, which results in the reduction of two Ce(4+) ions.     

YAG∶Ce体系中稀土离子掺杂对Ce3+的光谱性能的影响

采用高温固相法合成了一系列的(Y0.95Ln0.01Ce0.04)3Al5O12(简称YAG∶Ce,Ln), 系统地研究了此体系中的Ln3+对Ce3+的发光强度的影响. 结果表明, 在YAG∶Ce的体系中, La3+, Gd3+, Lu3+等光学透明离子的少量掺杂对Ce3+的发光强度的影响不大; 掺入少量的Pr3+, Sm3+, Tb3+, Dy3+, Ho3+, Er3+, Tm3+等稀土离子, 由于它们的能级与Ce3+的能级有交叠, 使它们之间存在着竞争吸收或能量转移, 对Ce3+的发光有较明显的变化, 其中, Pr3+和Sm3+的掺入使其在红光区有发射峰, 可以增加YAG∶Ce的红色成分以提高显色性; Nd3+, Eu3+和Yb3+对Ce3+的发光有严重的猝灭作用.     

Ce-Zr固溶体的纯度及其在三效催化剂中的作用

采用溶胶－凝胶法和有机溶剂分解法,制备了Ｃｅ－Ｚｒ固溶体。应用ＸＲＤ和ＬＲＳ谱测试,详细研究了经不同温度焙烧后固溶体的结构、晶相和热稳定性,并进行了储氧量、比表面积的测定和催化活性评价。结果表明,ＸＲＤ和ＬＲＳ相结合,可以较好地表征固溶体,并且储氧量高,但热稳定性较有机溶剂分解法制得的固溶体差;含富铈固溶体的三效催剂剂老化后的催化活性明显高于含纯ＣeＯ２的三效催化剂。     

The structural and electronic properties of nanostructured Ce1-x-yZrxTbyO2 ternary oxides: unusual concentration of Tb3+ and metal<-->oxygen<-->metal interactions

Ceria-based ternary oxides are widely used in many areas of chemistry, physics, and materials science. Synchrotron-based time-resolved x-ray diffraction, x-ray absorption near-edge spectroscopy (XANES), Raman spectroscopy, and density-functional calculations were used to study the structural and electronic properties of Ce-Zr-Tb oxide nanoparticles. The nanoparticles were synthesized following a novel microemulsion method and had sizes in the range of 4-7 nm. The Ce1-x-yZrxTbyO2 ternary systems exhibit a complex behavior that cannot be predicted as a simple extrapolation of the properties of Ce1-xZrxO2, Ce1-xTbxO2, or the individual oxides (CeO2, ZrO2, and TbO2). The doping of ceria with Zr and Tb induces a decrease in the unit cell, but there are large positive deviations with respect to the cell parameters predicted by Vegard's rule for ideal solid solutions. The presence of Zr and Tb generates strain in the ceria lattice through the creation of crystal imperfections and O vacancies. The O K-edge and Tb LIII-edge XANES spectra for the Ce1-x-yZrxTbyO2 nanoparticles point to the existence of distinctive electronic properties. In Ce1-x-yZrxTbyO2 there is an unexpected high concentration of Tb3+, which is not seen in TbO2 or Ce1-xTbxO2 and enhances the chemical reactivity of the ternary oxide. Tb<-->O<-->Zr interactions produce a stabilization of the Tb(4f,5d) states that is responsible for the high concentration of Tb(3+) cations. The behavior of Ce1-x-yZrxTbyO2 illustrates how important can be metal<-->oxygen<-->metal interactions for determining the structural, electronic, and chemical properties of a ternary oxide.     

Structural characterization of nanosized CeO(2)-SiO(2), CeO(2)-TiO(2), and CeO(2)-ZrO(2) catalysts by XRD, Raman, and HREM techniques

Structural characteristics of nanosized ceria-silica, ceria-titania, and ceria-zirconia mixed oxide catalysts have been investigated using X-ray diffraction (XRD), Raman spectroscopy, BET surface area, thermogravimetry, and high-resolution transmission electron microscopy (HREM). The effect of support oxides on the crystal modification of ceria cubic lattice was mainly focused. The investigated oxides were obtained by soft chemical routes with ultrahighly dilute solutions and were subjected to thermal treatments from 773 to 1073 K. The XRD results suggest that the CeO(2)-SiO(2) sample primarily consists of nanocrystalline CeO(2) on the amorphous SiO(2) surface. Both crystalline CeO(2) and TiO(2) anatase phases were noted in the case of CeO(2)-TiO(2) sample. Formation of cubic Ce(0.75)Zr(0.25)O(2) and Ce(0.6)Zr(0.4)O(2) (at 1073 K) were observed in the case of the CeO(2)-ZrO(2) sample. Raman measurements disclose the fluorite structure of ceria and the presence of oxygen vacancies/Ce(3+). The HREM results reveal well-dispersed CeO(2) nanocrystals over the amorphous SiO(2) matrix in the cases of CeO(2)-SiO(2), isolated CeO(2), and TiO(2) (anatase) nanocrystals, some overlapping regions in the case of CeO(2)-TiO(2), and nanosized CeO(2) and Ce-Zr oxides in the case of CeO(2)-ZrO(2) sample. The exact structural features of these crystals as determined by digital diffraction analysis of HREM experimental images reveal that the CeO(2) is mainly in cubic fluorite geometry. The oxygen storage capacity (OSC) as determined by thermogravimetry reveals that the OSC of the mixed oxide systems is more than that of pure CeO(2) and is system dependent.