甲醇在欠电位沉积Sn/Pt电极上催化氧化

在欠电位沉积（upd）锡修饰的铂电极（upd-Sn/Pt）上,对甲醇电化学催化氧化过程进行了研究.发现当Pt表面upd-Sn的覆盖率在20％附近时,对甲醇的催化氧化的增强作用最为明显；在电位低于0.35 V （vs RHE）时,甲醇在Pt与upd-Sn/Pt电极上氧化只进行到脱氢生成CO的步骤;在0.35 V以后,表面Sn－OH形成,反应Sn－OH＋COads=Sn＋CO2＋H＋＋e有利于表面CO的去除;而Pt电极上,只有0.6 V以后,才有反应Pt－OH＋COads=Pt＋CO2＋H＋＋e发生.因此,Sn的存在有利于甲醇在较低的电位下氧化; Pt电极上CH3OH脱氢并释放出电子的过程是一个快速的过程,表面CO的去除是甲醇氧化过程的控制步骤;甲醇氧化产生的表面吸附态CO 以线式吸附为主,少量的桥式吸附态CO在反应初期即达到吸附饱和; Pt表面上upd-Sn表现的催化增强作用,在光亮铂电极和在高分散铂黑电极上是一致的.     

Pt/巯基乙酸/玻碳电极的表面形貌与电催化性能

以巯基乙酸为偶联层在玻碳(GC)电极上组装 Pt纳米颗粒, 得到Pt /巯基乙酸/GC电极, 利用扫描电镜(SEM)和循环伏安法(CV)研究了不同条件下复合电极的表面形貌和电化学性能. 研究结果表明, 巯基乙酸在GC电极表面具有特性吸附, 形成了具有一定致密性的吸附层. 在0.5 mol/L H2SO4+1.0 mol/L CH3OH溶液中, 组装19 h的复合电极对甲醇氧化表现出较好的电催化性能.     

电化学方法制备高分散Pt/CMK-3及其对甲醇电化学催化性能

采用直接电化学还原法在介孔碳(CMK-3)载体上直接电沉积高分散的铂纳米颗粒,制备CMK-3复合铂纳米颗粒电极(Pt/CMK-3)。 通过透射电子显微镜分析发现,铂纳米颗粒非常均匀的分布在CMK-3上,平均粒径约5 nm。 通过循环伏安测试,分析了催化剂不同负载铂含量时氯铂酸的利用率,在理论铂质量分数为20%时,这种方法制备的Pt/CMK-3所使用的氯铂酸的利用率最高,在1 mol/L CH3OH+0.5 mol/L H2SO4溶液中循环伏安测试电流密度达到382 A/g。 在相同实验条件下,Pt/CMK-3电极对甲醇电催化活性远高于Pt/XC-72(炭黑)电极和用常规电沉积方法制备的Pt/CMK-3电极。     

甲酸在Pt-Ru/GC电极上氧化的SERS研究

采用循环伏安(CV)法、计时电流法和电化学原位表面增强拉曼散射光谱(SERS)技术研究了甲酸在Pt-Ru/GC电极上的氧化行为, 发现甲酸在Pt-Ru/GC电极上与在粗糙Pt电极上一样, 也能自发解离出强吸附中间体CO和活性中间体—COO－. 从分子水平证实钌的加入有利于提高电极对甲酸的电催化氧化活性, 当镀液中Pt：Ru的摩尔比从10∶1变化到1∶1, CO的氧化峰电位从0.41 V负移至0.35 V, 约负移了60 mV. Pt-Ru/GC(1∶1)电极与粗糙Pt电极相比, CO在电极表面氧化完毕的电位亦负移了约200 mV. 该研究结果表明, 电化学原位表面增强拉曼散射光谱技术可望成为研究电催化反应机理的普适谱学工具.     

Pt/PMo12/PEDOT/GC电极的制备及其甲醇电氧化性能

将磷钼酸(PMo12)修饰到电化学聚合制得的聚3,4-乙烯二氧噻吩(PEDOT)(PEDOT/GC)膜表面(PMo12/PEDOT/GC),随后电沉积Pt得Pt/PMo12/PEDOT/GC电极.研究了PMo12和PEDOT对电极氧化甲醇性能的影响.结果表明,PMo12改变了电极上负载Pt的形态和结构,导致Pt纳米结构边缘产生尖锐的刺状结构.Pt/PMo12/PEDOT/GC和Pt/PEDOT/GC电极有较好的甲醇氧化电催化活性,而前者尤佳.PEDOT不仅提高甲醇氧化的电流,还使甲醇的起始氧化电位负移.进一步修饰PMo12后,可明显增大甲醇氧化的电流.     

Pt-Se纳米空球修饰玻碳电极上甲酸的电催化氧化

以无定形硒溶胶为模板制备了不同硒覆盖度(θSe)(θSe=0.49,0.39,0.06,0)的Pt-Se和Pt纳米空球(分别记为(Pt-Se)HN和PtHN),发展了利用亚硫酸盐彻底除去核壳纳米粒子上Se的方法.对获得的纳米空球进行了形貌和结构的表征,结果表明所制备的(Pt-Se)HN粒径均匀,分散性好,球壳呈多孔结构.以其作为电催化剂制备了(Pt-Se)HN修饰的玻碳(GC)电极((Pt-Se)HN/GC),利用常规电化学方法比较该电极与PtHN/GC和商用碳载铂(Pt/C)修饰GC(Pt/C/GC)电极对甲酸的催化氧化作用,发现对甲酸氧化的活性顺序为(Pt-Se)HN/GCPtHN/GCPt/C/GC.三种电极催化甲酸氧化的机理有所不同:前者更倾向于通过弱吸附中间体直接氧化成CO2的单途径机理进行,后两者则通过强吸附和弱吸附中间体的双途径机理进行.在一定Se覆盖度条件下,(Pt-Se)HN/GC对甲酸的氧化有助催化作用.     

碳载Pt/Sb_(ad)电极上乙醇电催化氧化特征和原位FTIR反射光谱研究

用电化学循环伏安法和原位 FTIR反射光谱法研究了 Sb在碳载纳米 Pt膜电极 (nm -Pt/ GC)表面不可逆吸附的电化学特性及酸性介质中乙醇的吸附和电催化氧化特性 .结果指出 ,当扫描电位的上限 Eu≤0 .5 0 V(SCE)时 ,Sbad可以稳定地吸附在 nm-Pt/ GC电极表面 .与未修饰的 nm-Pt/ GC电极上结果相比 ,Sbad修饰的 nm-Pt/ GC/ Sbad/ (nm-Pt/ GC)的催化活性显著增加 .测得当覆盖度θsb=0 .1 3 7时 ,修饰电极对乙醇的电催化活性最高 ,乙醇氧化的峰电位负移了 0 .1 5 V,峰电流增大了 1倍 .原位 FTIR反射光谱的结果从分子水平揭示了 Sb修饰对乙醇氧化反应途径的选择功能 .     

不同介质对Pt/GC电极制备及其性能的影响

应用循环伏安法(CV),扫描电子显微镜(SEM)和电化学原位红外反射光谱(in situFTIRS)研究了不同介质对碳载铂纳米薄膜电极(Pt/GC)的表面结构以及该薄膜电极对甲酸电催化氧化性能的影响.结果表明,使用不同介质的镀铂溶液,均可电沉积出分布较为均匀的Pt粒子,但其尺寸与形貌却相差很大.当以H2SO4作介质,由循环伏安法于玻碳电极上电沉积Pt得到的(Pt/GC1)电极,其Pt粒子粒径约100~200 nm;而在HClO4介质得到的(Pt/GC2)电极,则含有两种Pt微晶:其一是立方体形,粒径约200 nm,其二为菜花状,粒径约400 nm.电化学循环伏安和原位红外反射光谱测试指明,不同介质制备的Pt/GC电极对甲酸的电催化氧化均表现出与本体铂电极(Pt)相类似的特性,即可通过活性中间体或毒性中间体将甲酸氧化至CO2,但不同结构的Pt/GC电极具有不同的电催化活性.进一步以Sb或Pb修饰Pt/GC电极,不仅可以有效地抑制毒性中间体CO的生成,而且还能显著提高其电催化活性.比较本文研究的7种电极,其电催化活性顺序依次为:Sb-Pt/GC2>Pb-Pt/GC2>Pb-Pt/GC1>Sb-Pt/GC1>Pt/GC2>Pt/GC1>Pt.     

乙醇在碳载Pt纳米薄膜电极上吸附氧化过程研究Ⅰ.碱性介质中循环伏安和原位FTIR反射光谱

运用电化学循环伏安法在玻碳载体上制备纳米级厚度的Pt薄膜电极 ,用STM表征电极表面的形貌 ,测定了电沉积层的厚度、表面积和Pt载量 .同时 ,应用电化学循环伏安法和原位FTIR反射光谱研究了乙醇在碱性介质中的吸附和氧化行为 .结果表明 ,乙醇氧化的主要产物是CH3COO- ,仅存在少量乙醛 ,并未观察到任何CO谱峰 .与酸性介质中乙醇氧化的双途径机理不同 ,碱性介质中乙醇氧化未经过解离吸附中间过程     

铁铂核壳纳米粒子修饰玻碳电极制备及对亚硝酸盐还原的电催化性能

通过循环伏安法（CV）在玻碳（GC）电极表面电沉积出分布较为均匀的纳米Fe粒子,制得纳米Fe粒子修饰的GC（纳米Fe/GC）电极,再经“电荷置换”制得具有Fe核Pt壳结构的纳米粒子修饰的（纳米PtFe/GC）电极。 SEM结果显示,纳米Fe/GC和纳米PtFe/GC表面粒子的形貌均呈立方体形,分布较为均匀,粒径在60 nm左右。 纳米PtFe/GC电极对亚硝酸盐的还原具有很高的电催化活性。 3种电极的电催化活性顺序依次为：纳米Fe/GC＜纳米Pt/GC＜纳米PtFe/GC。 相对于纳米Pt/GC电极,纳米PtFe/GC电极的起始还原电位（Ei）正移了0.14 V,还原峰电流（ip）增大了3倍。     

Investigation of electro-oxidation activity of Pt-CNTs/GC electrodes

The morphology and structure of Pt-CNTs/ GC electrodes were characterized via Transmission Electron Microscopy (TEM) and selected area electron diffraction. The electro-oxidation behavior of CO and methanol on Pt-CNTs/GC electrodes were studied with cyclic voltommograms or chronoamperometry. Three oxidation peaks were observed for CO absorbed on Pt-CNTs/GC electrodes. Methanol was found to be dissociated spontaneously on the electrode to produce a strong absorbed intermediate CO. Among the three oxidation peaks, peak I was presumed to be due to the bridged CO absorption while peaks II and III were attributed to the split in the linear CO which is absorbed on the Pt-CNTs/GC nanocluster with different particle size and Pt film. The oxidation current of methanol on the Pt-CNTs/GC electrode did not always increase with the increase in the amount of Pt loading. The result indicates that there is an optimal Pt loading for methanol oxidation. It is necessary to select the catalyst with proper Pt loading when the anode of a direct-methanol fuel cell is prepared. __________ Translated from Chemical Journal of Chinese Universities, 2007, 28(6): 1135–1138 [译自: 高等学校化学学报]     

CoPt nanoparticles and their catalytic properties in electrooxidation of CO and CH(3)OH studied by in situ FTIRS

CoPt nanoparticles supported on a glassy carbon electrode (denoted as CoPt/GC) were prepared by galvanic replacement reaction between electrodeposited Co nanoparticles and K(2)PtCl(6) solution. Scanning electron microscope (SEM) and transmission electron microscope (TEM) were both employed to characterize the CoPt nanoparticles. It was shown that the CoPt nanoparticles have irregular shapes and most of them exhibit a core-shell structure with a porous Co core and a shell of Pt tiny particles. The composition of the CoPt nanoparticles was analyzed by energy-dispersive X-ray spectroscopy (EDX), which depicts a Co : Pt ratio of ca. 21 : 79. Studies of cyclic voltammetry (CV) demonstrated that CoPt/GC possesses a much higher catalytic activity towards CO and methanol electrooxidation than a nanoscale Pt thin film electrode. In situ FTIR spectroscopic studies have revealed for the first time, that a CoPt nanoparticles electrode exhibits abnormal IR effects (AIREs) for IR absorption of CO adsorbed on it. In comparison with the IR features of CO adsorbed on a bulk Pt electrode, the direction of the IR bands of CO adsorbed on the CoPt/GC electrode is inverted completely, and the intensity of the IR bands has been enhanced up to 15.4 times. The AIREs is significant in detecting the adsorbed intermediate species involved in electrocatalytic reactions. The results demonstrated a reaction mechanism of CH(3)OH oxidation on CoPt/GC in alkaline solutions through evidencing CO(L), CO(M), HCOO(-), CO(3)(2-), HCO(3)(-) and CO(2) as intermediate and product species by in situ FTIRS.     

磷钼酸修饰铂电极的电化学行为及对甲醇氧化的电催化作用

通过循环伏安扫描法制备了PMo₁₂修饰Pt/Pt电极,并研究了该修饰电极在硫酸溶液中的电化学行为。研究结果表明:虽然磷钼酸具有较大的分子尺寸,但在Pt/Pt电极上仍能发生吸附作用,并且由于PMo₁₂在电极上的吸附,降低了Pt/Pt电极上氢区和氧区的荷电量,另外在0.02V左右还观察到磷钼酸的氧化-还原峰。通过稳态极化曲线和循环伏安曲线研究了PMo₁₂修饰Pt/Pt电极对甲醇氧化的电催化作用。测试结果表明:PMo₁₂修饰铂基电极不但对甲醇的电氧化具有较高的活性,而且还有一定的抗CO中毒性。该修饰电极还具有较高的稳定性。     

甲醇在铂微粒修饰的聚硫堇电极上的电催化氧化

利用电化学循环伏安和现场ＦＴＩＲ反射光谱等技术研究了甲醇在铂微粒修饰的聚硫堇电极上的电催化氧化。结果表明，循环伏安法制备的铂微粒均匀分散于聚合物膜上，其粒径大小约为３０－１３０ｎｍ；复合修饰电极对甲醇电化学氧化呈现了较高的催化活性，其催化活性的大小依赖于Ｐｔ载量。现场ＦＴＩＲ光谱实验揭示了线性吸附的ＣＯ物种是甲醇在复合电极上氧化的唯一中间体，这种吸附的ＣＯ物种在复合修饰电极上更容易被氧化为最终产物     

Modification of a Pt surface by spontaneous Sn deposition for electrocatalytic applications. 2. Oxidation of CO,formaldehyde, formic acid,and methanol

The electrocatalytic activity of a spontaneously tin-modified Pt catalyst, fabricated through a simple dip-coating method under open-circuit conditions and characterized using surface analysis methods, was studied in electrooxidation reactions of a preadsorbed CO monolayer and continuous oxidation of methanol, formic acid, and formaldehyde in the potentiodynamic and potentiostatic modes. The catalytic activity of the tin-modified Pt surface is compared with that of a polycrystalline Pt electrode. Spontaneously Sn-modified Pt catalyst shows a superior activity toward adsorbed CO oxidation and thus can be promising for PEFC applications. The methanol oxidation rate is not enhanced on the Sn-modified Pt surface, compared to the Pt electrode. Formic acid oxidation is enhanced in the low potential region on the Sn-modified surface, compared to the Pt electrode. The formaldehyde oxidation rate is dramatically increased by modifying tin species at the most negative potentials, where anodic formaldehyde oxidation is completely suppressed on the pure Pt electrode. The results are discussed in terms of poisoning CO intermediate formation resulting from dehydrogenation of organic molecules on Pt sites, and oxidation of poisoning adsorbed CO species via the surface reaction with OH adsorbed on neighboring Sn sites.     

Pt-Mo电极上CO、甲醛和甲醇的电催化氧化-微分电化学质谱研究

利用微分电化学质谱（DEMS）研究了Mo修饰的Pt电极上CO、甲醛和甲醇的电催 化氧化,证实了Mo(IV)是催化活性样品,而且它只对弱吸附CO的氧化起催化作用, 对强吸附CO的氧化没有催化活性。在低于0.4 V的电位下,吸附在Pt电极上的Mo结 甲醇和甲醛的催化氧化是通过弱吸附CO的氧化路径进行的。     

Effect of the iridium oxide thin film on the electrochemical activity of platinum nanoparticles

The influence of the iridium oxide thin film on the electrocatalytic properties of platinum nanoparticles was investigated using the electro-oxidation of methanol and CO as a probe. The presence of the IrO(2) thin film leads to the homogeneous dispersion of Pt nanoparticles. For comparison, polycrystalline platinum and Pt nanoparticles dispersed on a Ti substrate in the absence of an IrO(2) layer (Ti/Pt) were also investigated in this study. Inverted and enhanced CO bipolar peaks were observed using an in situ electrochemical Fourier transform infrared technique during the methanol oxidation on the Pt nanoparticles dispersed on a Ti substrate. Electrochemical impedance studies showed that the charge transfer resistance was significantly lower for the Ti/IrO(2)/Pt electrode compared with that of the massive Pt and Ti/Pt nanoparticles. The presence of the IrO(2) thin film not only greatly increases the active surface area but also promotes CO oxidation at a much lower electrode potential, thus, significantly enhancing the electrocatalytic activity of Pt nanoparticles toward methanol electro-oxidation.     

Electrooxidation of carbon monoxide and methanol on platinum-overlayer-coated gold nanoparticles: effects of film thickness

The electrooxidation of carbon monoxide and methanol on Pt-coated Au nanoparticles attached to 3-aminopropyl trimethoxysilane-modified indium tin oxide electrodes was examined as a function of Pt film thickness and Au particle coverage. For the electrodes with medium and high Au particle coverages, the CO stripping peak position shifts to more negative values with increasing Pt film thickness, from ca. 0.8 V (vs Ag/AgCl) at 1 ML to 0.45 V at 10 ML. Accompanying this peak potential shift is the sharpening of the peak width from more than 150 to 65 mV. For the electrode with low Au particle coverage, similar peak width narrowing was also observed, but the peak potential shift is much smaller, from 0.85 V at 1 ML of Pt to 0.65 V at 10 ML. These observations are compared with the CO oxidation on bulk Pt electrodes and on Pt films deposited on bulk Au electrodes. The film-thickness-dependent CO oxidation is explained by d band theory in terms of strain and ligand effects, the particle size effect, and the particle aggregation induced by Pt film growth. Corresponding to the increasing CO oxidation activity, the current density of methanol oxidation grows with the Pt film thickness. The peak potential and current density reach the same values as those obtained on a polycrystalline bulk Pt electrode when more than 4 ML of Pt is deposited on the Au particle electrodes with a particle coverage higher than 0.25. These results suggest that it is feasible to reduce Pt loading in methanol fuel cells by using Pt thin films as the anode catalyst.     

甲醇在铂修饰的氧化钛电极上电催化氧化行为的研究

运用电化学方法评价了电化学阴极还原-阳极氧化两步法制得的以钛为基体的铂修饰的钛氧化物(Pt-TiO_x/Ti)电极对甲醇电催化氧化的性能,结果表明,制得的修饰电极对甲醇氧化呈现了很高的电催化活性和好的稳定性.通过X光电子能谱(XPS)、扫描隧道显微镜(STM)和现场傅立叶变换红外(FTIR)反射光谱等技术,发现修饰电极对甲醇氧化具有高的电催化性能,可归属于纳米级Pt粒子在TiO_x中的高度分散及由于Pt和TiO_x的相互作用,使电极表面对甲醇氧化中间产物CO的吸附量大大降低.     

Carbon‐Supported Pt Particles as a Catalyst for Electrooxidation of Methanol and Cyclic Voltammetry Studies Under Acidic Conditions

Electrooxidation of methanol on glassy carbon (GC) electrode modified by optimum carbon supported Pt electrocatalyst (Pt‐C/GC) in acid media is investigated. The catalyst is prepared by ultrasonicating Pt/C powders in aqueous media. The activity of prepared Pt‐C/GC electrode is studied in potential range of 0–1000 mV (versus SCE) by cyclic voltammetry. The results showed that the Pt/C dispersed layer at the surface of glassy carbon electrode, behaves as an electrocatalyst for the oxidation of methanol in acid medium by optimum loading of Pt (0.2 mg cm^?2). The electrochemical properties of prepared electrode are studied under various conditions. However the effect of various parameters in the catalytic enhancement of Pt/C, such as platinum loading, sulfuric acid concentration, different scan rates, different final potentials, and medium temperature are considered and examined.