Prussian Blue electrodeposited on MWNTs-PANI hybrid composites for H2O2 detection

A Prussian Blue (PB)/polyaniline (PANI)/multi-walled carbon nanotubes (MWNTs) composite film was fabricated by step-by-step electrodeposition on glassy carbon electrode (GCE). The electrode prepared exhibits enhanced electrocatalytic behavior and good stability for detection of H₂O₂ at an applied potential of 0.0 V. The effects of MWNTs thickness, electrodeposition time of PANI and rotating rate on the current response of the composite modified electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. A linear range from 8 × 10⁻⁹ to 5 × 10⁻⁶ M for H₂O₂ detection has been observed at the PB/PANI/MWNTs modified GCE with a correlation coefficient of 0.997. The detection limit is 5 × 10⁻⁹ M on signal-to-noise ratio of 3. To the best of our knowledge, this is the lowest detection limit for H₂O₂ detection. The electrode also shows high sensitivity (526.43 μA μM⁻¹ cm⁻²) for H₂O₂ detection which is more than three orders of magnitude higher than the reported.     

High selective SiO2-Al2O3 mixed-oxide modified carbon paste electrode for anodic stripping voltammetric determination of Pb(II)

The main purpose of this study is to develop an inexpensive, simple, selective and especially highly selective modified mixed-oxide carbon paste electrode (CPE) for voltammetric determination of Pb(II). For the preliminary screening purpose, the catalyst was prepared by modification of SiO₂-Al₂O₃ mixed-oxide and characterized by TG, CHN elemental analysis and FTIR spectroscopy. Using cyclic voltammetry the electroanalytical characteristics of the catalyst have been determined, and consequently the modified mixed-oxide carbon paste electrode was constructed and applied for determination of Pb(II). The electroanalytical procedure for determination of the Pb(II) comprises two steps: the chemical accumulation of the analyte under open-circuit conditions followed by the electrochemical detection of the preconcentrated species using differential pulse anodic stripping voltammetry. During the preconcentration step, Pb(II) was accumulated on the surface of the modifier by the formation of a complex with the nitrogen atoms of the pyridyl groups in the modifier. The peak currents increases linearly with Pb(II) concentration over the range of 2.0 × 10⁻⁹ to 5.2 × 10⁻⁵ mol L⁻¹ (r² = 0.9995).The detection limit (three times signal-to-noise) was found to be 1.07 × 10⁻⁹ mol L⁻¹ Pb(II). The chemical and instrumental parameters have been optimized and the effect of the interferences has been determined. The Proposed method was used for determination of lead ion in the real samples.     

Immobilization of [Cu(bpy)2]Br2 complex onto a glassy carbon electrode modified with α-SiMo12O40 and single walled carbon nanotubes: Application to nanomolar detection of hydrogen peroxide and bromate

A simple procedure has been used for preparation of modified glassy carbon electrode with carbon nanotubes and copper complex. Copper complex [Cu(bpy)₂]Br₂ was immobilized onto glassy carbon (GC) electrode modified with silicomolybdate, α-SiMo₁₂O₄₀⁴⁻ and single walled carbon nanotubes (SWCNTs)_. Copper complex and silicomolybdate irreversibly and strongly adsorbed onto GC electrode modified with CNTs. Electrostatic interactions between polyoxometalates (POMs) anions and Cu-complex, cations mentioned as an effective method for fabrication of three-dimensional structures. The modified electrode shows three reversible redox couples for polyoxometalate and one redox couple for Cu-complex at wide range of pH values. The electrochemical behavior, stability and electron transfer kinetics of the adsorbed redox couples were investigated using cyclic voltammetry. Due to electrostatic interaction, copper complex immobilized onto GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ electrode shows more stable voltammetric response compared to GC/CNTs/Cu-complex modified electrode. In comparison to GC/CNTs/Cu-complex the GC/CNTs/α-SiMo₁₂O₄₀⁴⁻ modified electrodes shows excellent electrocatalytic activity toward reduction H₂O₂ and BrO₃⁻ at more reduced overpotential. The catalytic rate constants for catalytic reduction hydrogen peroxide and bromate were 4.5(±0.2) × 10³ M⁻¹ s⁻¹ and 3.0(±0.10) × 10³ M⁻¹ s⁻¹, respectively. The hydrodynamic amperommetry technique at 0.08 V was used for detection of nanomolar concentration of hydrogen peroxide and bromate. Detection limit, sensitivity and linear concentration range proposed sensor for bromate and hydrogen peroxide detection were 1.1 nM and 6.7 nA nM⁻¹, 10 nM-20 μM, 1 nM, 5.5 nA nM⁻¹ and 10 nM-18 μM, respectively.     

Composite film of carbon nanotubes and chitosan for preparation of amperometric hydrogen peroxide biosensor

A new amperometric biosensor for hydrogen peroxide was developed based on cross-linking horseradish peroxidase (HRP) by glutaraldehyde with multiwall carbon nanotubes/chitosan (MWNTs/chitosan) composite film coated on a glassy carbon electrode. MWNTs were firstly dissolved in a chitosan solution. Then the morphology of MWNTs/chitosan composite film was characterized by field-emission scanning electron microscopy. The results showed that MWNTs were well soluble in chitosan and robust films could be formed on the surface. HRP was cross-linked by glutaraldehyde with MWNTs/chitosan film to prepare a hydrogen peroxide biosensor. The enzyme electrode exhibited excellent electrocatalytic activity and rapid response for H₂O₂ in the absence of a mediator. The linear range of detection towards H₂O₂ (applied potential: −0.2 V) was from 1.67 × 10⁻⁵ to 7.40 × 10⁻⁴ M with correction coefficient of 0.998. The biosensor had good repeatability and stability for the determination of H₂O₂. There were no interferences from ascorbic acid, glucose, citrate acid and lactic acid.     

Bilayer lipid membrane biosensor with enhanced stability for amperometric determination of hydrogen peroxide

In this paper, a polydopamine (PDA) film is electropolymerized on the surface of bilayer lipid membrane (BLM) which is immobilized with horseradish peroxidase (HRP). The coverage of the PDA film on HRP/BLM electrode is monitored by electrochemical impedance spectroscopy (EIS). The electrocatalytic reduction of H₂O₂ at the PDA/HRP/BLM electrode is studied by means of cyclic voltammetry (CV). The biosensor has a fast response to H₂O₂ of less than 5 s and an excellent linear relationship is obtained in the concentration range from 2.5 × 10⁻⁷ to 3.1 × 10⁻³ mol L⁻¹, with a detection limit of 1.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The response current of BLM/HRP/PDA biosensor retains 84% of its original response after being stored in 0.1 mol L⁻¹ pH 7.0 PBS at 4 °C for 3 weeks. The selectivity, repeatability, and storage stability of PDA/HRP/BLM biosensor are greatly enhanced by the coverage of polydopamine film on BLM.     

Synthesis of Fe3O4\SiO2\Ag nanoparticles and its application in surface-enhanced Raman scattering

To obtain a recyclable surface-enhanced Raman scattering (SERS) material, we developed a composite of Fe₃O₄\SiO₂\Ag with core\shell\particles structure. The designed particles were synthesized via an ultrasonic route. The Raman scattering signal of Fe₃O₄ could be shielded by increasing the thickness of the SiO₂ layer to 60 nm. Dye rhodamine B (RB) was chosen as probe molecule to test the SERS effect of the synthesized Fe₃O₄\SiO₂\Ag particles. On the synthesized Fe₃O₄\SiO₂\Ag particles, the characteristic Raman bands of RB could be observed when the RB solution was diluted to 5 ppm (1×10⁻⁵ M). Furthermore, the synthesized particles could keep their efficiency till four cycles.     

Direct electrocatalytic oxidation of nitric oxide and reduction of hydrogen peroxide based on α-Fe2O3 nanoparticles-chitosan composite

α-Fe₂O₃ nanoparticles prepared using a simple solution-combusting method have been dispersed in chitosan (CH) solution to fabricate nanocomposite film on glass carbon electrode (GCE). The as-prepared α-Fe₂O₃ nanoparticles were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM). The nanocomposite film exhibits high electrocatalytic oxidation for nitric oxide (NO) and reduction for hydrogen peroxide (H₂O₂). The electrocatalytic oxidation peak is observed at +0.82 V (vs. Ag/AgCl) and controlled by diffusion process. The electrocatalytic reduction peak is observed at −0.45 V (vs. Ag/AgCl) and controlled by diffusion process. This α-Fe₂O₃-CH/GCE nanocomposite bioelectrode has response time of 5 s, linearity as 5.0 × 10⁻⁷ to 15.0 × 10⁻⁶ M of NO with a detection limit of 8.0 × 10⁻⁸ M and a sensitivity of −283.6 μA/mM. This α-Fe₂O₃-CH/GCE nanocomposite bioelectrode was further utilized in detection of H₂O₂ with a detection limit of 4.0 × 10⁻⁷ M, linearity as 1.0 × 10⁻⁶ to 44.0 × 10⁻⁶ M and with a sensitivity of 21.62 μA/mM. The shelf life of this bioelectrode is about 6 weeks under room temperature conditions.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.     

Electrocatalytic oxidation behavior of guanosine at graphene, chitosan and Fe3O4 nanoparticles modified glassy carbon electrode and its determination

A graphene, chitosan and Fe₃O₄ nanoparticles (nano-Fe₃O₄) modified glassy carbon electrode (graphene-chitosan/nano-Fe₃O₄/GCE) was fabricated. The modified electrode was characterized by scanning electron microscope and electrochemical impedance spectroscopy. The electrochemical oxidation behavior of guanosine was investigated in pH 7.0 phosphate buffer solution by cyclic voltammetry and differential pulse voltammetry. The experimental results indicated that the modified electrode exhibited an electrocatalytic and adsorptive activities towards the oxidation of guanosine. The transfer electron number (n), transfer proton number (m) and electrochemically effective surface area (A) were calculated. Under the optimized conditions, the oxidation peak current was proportional to guanosine concentration in the range of 2.0 × 10⁻⁶ to 3.5 × 10⁻⁴ mol L⁻¹ with the correlation coefficient of 0.9939 and the detection limit of 7.5 × 10⁻⁷ mol L⁻¹ (S/N = 3). Moreover, the modified electrode showed good ability to discriminate the electrochemical oxidation response of guanosine, guanine and adenosine. The proposed method was further applied to determine guanosine in spiked urine samples and traditional Chinese medicines with satisfactory results.     

A novel amperometric biosensor for the detection of nitrophenol

We report on a novel amperometric biosensor for detecting phenolic compounds based on the co-immobilization of horseradish-peroxidase (HRP) and methylene blue (MB) with chitosan on Au-modified TiO₂ nanotube arrays. The titania nanotube arrays were directly grown on a Ti substrate using anodic oxidation first; a gold thin film was then coated onto the TiO₂ nanotubes by an argon plasma technique. The morphology and composition of the fabricated Au-modified TiO₂ nanotube arrays were characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Cyclic voltammetry and amperometry were used to study the proposed electrochemical biosensor. The effect of pH, applied electrode potential and the concentration of H₂O₂ on the sensitivity of the biosensor have been systemically investigated. The performance of the proposed biosensor was tested using seven different phenolic compounds, showing very high sensitivity; in particular, the linearity of the biosensor for the detection of 3-nitrophenol was observed from 3 × 10⁻⁷ to 1.2 × 10⁻⁴ M with a detection limit of 9 × 10⁻⁸ M (based on the S/N = 3).     

Direct electrochemistry and electrocatalysis of hemoglobin immobilized in a magnetic nanoparticles-chitosan film

Magnetic nanoparticles (Fe₃O₄) were synthesized by a chemical coprecipitation method. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to confirm the crystallite structure and the particle's radius. The Fe₃O₄ nanoparticles and chitosan (CS) were mixed to form a matrix in which haemoglobin (Hb) can be immobilized for the fabrication of H₂O₂ biosensor. The Fe₃O₄-CS-Hb film exhibited a pair of well-defined and quasi-reversible cyclic voltammetric peaks due to the redox of Hb-heme Fe (III)/Fe (II) in a pH 7.0 phosphate buffer. The formal potential of Hb-heme Fe(III)/Fe(II) couple varied linearly with the increase of pH in the range of 4.0-10.0 with a slope of 46.5 mV pH⁻¹, indicating that electron transfer was accompanied with single proton transportation in the electrochemical reaction. The surface coverage of Hb immobilized on Fe₃O₄-CS film glassy carbon electrode was about 1.13 × 10⁻¹⁰ mol cm⁻². The heterogeneous electron transfer rate constant (k_s) was 1.04 s⁻¹, indicating great facilitation of the electron transfer between Hb and magnetic nanoparticles-chitosan modified electrode. The modified electrode showed excellent electrocatalytic activity toward oxygen and hydrogen peroxide reduction. The apparent Michaelis-Menten constant for H₂O₂ was estimated to be 38.1 μmol L⁻¹.     

Improved potentiometric response of solid-contact lanthanum (III) selective electrode

For the first time, the analytical application of integrate ionophore-transducer material based on magnetic graphene hybrids and 2,2-dithiodipyridine (DTDP) in solid-contact lanthanum (III) selective electrode is reported. The attachment of Fe₃O₄ nanoparticles (NPs) to graphene oxide (GO) for magnetic graphene hybrid is achieved by covalent bonding, and the universal problem, Fe₃O₄ NPs may easily leach out from the graphene during application, is successfully solved by the method above. The proposed electrode exhibits an excellent near-Nernstian response to lanthanum (III) ranging from 1.0 × 10⁻⁹ to 1.0 × 10⁻³ M with a slope of 17.81 mV/dec. Moreover, the excellent performance on fairly good selectivity, wide applicable pH range (3.0^_8.0), fast response time (10 s) and long life time (2 months) reveal the superiority of the electrode. Most importantly, we have made a great improvement in the detection limit (2.75 × 10⁻¹⁰ M), which brings new dawn to the real-time detection of lanthanum (III) using ion selective electrode.     

Potentiometric sensor using sub-micron Cu2O-doped RuO2 sensing electrode with improved antifouling resistance

A Cu₂O-doped RuO₂ sensing electrode (SE) for potentiometric detection of dissolved oxygen (DO) was prepared and its structure and electrochemical properties were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron microscopy (XPS) and energy-dispersive spectroscopy (EDS) techniques. Cu₂O-RuO₂-SE displayed a linear DO response from 0.5 to 8.0 ppm (log[O₂], −4.73 to −3.59) within a temperature range of 9-30 °C. The maximum sensitivity of −47.4 mV/decade at 7.27 pH was achieved at 10 mol% Cu₂O. Experimental evaluation of the Cu₂O-doped RuO₂-SE demonstrated that the doping of RuO₂ not only improves its structure but also enhances both sensor's selectivity and antifouling properties. Selectivity measurements revealed that 10 mol% Cu₂O-doped RuO₂-SE is insensitive to the presence of Na⁺, Mg²⁺, K⁺, Ca²⁺, NO₃⁻, PO₄²⁻ and SO₄²⁻ ions in the solution in the concentration range of 10⁻⁷-10⁻¹ mol/l.     

A nano-porous CeO(2)/Chitosan composite film as the immobilization matrix for colorectal cancer DNA sequence-selective electrochemical biosensor

CeO₂/Chitosan (CHIT) composite matrix was firstly developed for the single-stranded DNA (ssDNA) probe immobilization and the fabrication of DNA biosensor related to the colorectal cancer gene. Such matrix combined the advantages of CeO₂ and chitosan, with good biocompatibility, nontoxicity and excellent electronic conductivity, showing the enhanced loading of ssDNA probe on the surface of electrode. The preparation method is quite simple and inexpensive. The hybridization detection was accomplished by using methylene blue (MB), an electroactive lable, as the indicator. The differential pulse voltammetry (DPV) was employed to record the signal response of MB and determine the amount of colorectal cancer target DNA sequence. The experimental conditions were optimized. The established biosensor has high detection sensitivity, a relatively wide linear range from 1.59 × 10⁻¹¹ to 1.16 × 10⁻⁷ mol L⁻¹ and the ability to discriminate completely complementary target sequence and four-base-mismatched sequence.     

High-resolution transmission electron microscopy investigation of nanostructures in SnO2 thin films prepared by pulsed laser deposition

Pulsed laser deposition (PLD) was used to grow nanocrystalline SnO₂ thin films onto glass substrates. The nanocrystallites and microstructures in SnO₂ thin films grown by PLD techniques have been investigated in detail by using X-ray diffraction and high-resolution transmission electron microscopy (HRTEM). The PLD process was carried out at room temperature under a working pressure of about 2×10⁻⁶ mbar. Experimental results indicate that thin films are composed of a polycrystalline SnO₂ and an amorphous SnO phase. In particular, the presence of such an amorphous SnO phase in the thin films greatly limits their practical use as gas-sensing devices. HRTEM observations revealed that SnO₂ nanocrystallites with tetragonal rutile structure embed in an amorphous SnO matrix, which are approximatively equiaxed. These approximatively equiaxed SnO₂ nanocrystallites contain a high density of defects, such as twin boundaries and edge dislocations. The grain growth of SnO₂ thin films may be discussed in terms of the coalescent particle growth mechanism.     

Amperometric biosensor based on a nanoporous ZrO2 matrix

A biosensor was investigated based on the use of ZrO₂ sol-gel matrix for enzyme immobilization in the mild condition. This bioceramic zirconia alcogel has been prepared by the novel alcohothermal route with a cheap inorganic salt Zr(NO₃)₄·5H₂O with several desirable features including a large surface area (about 460 m² g⁻¹) as well as pore volume and a well-developed textural mesoporosity, and horseradish peroxidase was selected as a model enzyme. The results of transmission electron microscopy (TEM) and BET measurement of the substrate showed that the as-prepared zirconia matrix has an advantageous microenvironment and large surface area available for high enzyme loading. The parameters affecting both the entrapment of enzyme and the biosensor response were optimized. The resulting biosensor exhibited high sensitivity of 111 μA mM⁻¹ for hydrogen peroxide over a wide range of concentrations from 2.5×10⁻⁷ to 1.5×10⁻⁴ mol l⁻¹, quick response of less than 10 s and good stability over 3 months.     

A new electrochemiluminescent detection system equipped with an electrically controlled heating cylindrical microelectrode

A new electrochemiluminescent (ECL) detection system equipped with an electrically controlled heating cylindrical microelectrode (HME) was developed in this paper. The cylindrical microelectrode made of platinum wire (25 μm in diameter, 6 mm in long) was used as the working electrode of the ECL detection system, the temperature of the electrode could be controlled electrically. The Ru(bpy)₃²⁺-ECL and Ru(bpy)₃²⁺-C₂O₄²⁻-ECL systems were used to evaluate this ECL detection system. The detection limit for oxalate was found to be 3.0 × 10⁻⁴ mol/L when T_e (temperature of the HME) was 22 °C, and found to be 3.0 × 10⁻⁶ mol/L at 80 °C, which indicates that the detection limit can be improved greatly at higher T_e, based on which, it is possible to establish a more sensitive method for measurement of ECL by using a heated microelectrode.     

Use of Nb(2)O(5)-SiO(2) in an automated on-line preconcentration system for determination of copper and cadmium by FAAS

A procedure for the determination of trace level of copper(II) and cadmium(II) by FAAS using an on-line preconcentration system has been proposed. In this system, copper and cadmium ions were adsorbed onto a minicolumn packed with silica gel modified with niobium(V) oxide (Nb₂O₅-SiO₂), followed by nitric acid elution in reverse mode and determination on-line by flame atomic absorption spectrometry (AAS) without interference of the matrix. Chemical and flow variables as well as concomitant ions were studied in the developed procedure. The enrichment factor for copper(II) and cadmium(II) was 34.2 and 33.0, respectively, using a preconcentration time of 2 min. The limit of detection for copper(II) and cadmium(II) was 0.4, and 0.1 μg l⁻¹, respectively. The precision of the method, evaluated as the relative standard deviation in solutions containing 15 μg l⁻¹ of copper and 10 μg l⁻¹ of cadmium, by analyzing a series of seven replicates, was 1.8 and 1.6%, respectively. The accuracy was assessed through recovery experiments of certified material and water samples.     

Fluorometric method for the determination of hydrogen peroxide and glucose with Fe3O4 as catalyst

In this paper, we utilized the instinct peroxidase-like property of Fe₃O₄ magnetic nanoparticles (MNPs) to establish a new fluorometric method for determination of hydrogen peroxide and glucose. In the presence of Fe₃O₄ MNPs as peroxidase mimetic catalyst, H₂O₂ was decomposed into radical that could quench the fluorescence of CdTe QDs more efficiently and rapidly. Then the oxidization of glucose by glucose oxidase was coupled with the fluorescence quenching of CdTe QDs by H₂O₂ producer with Fe₃O₄ MNPs catalyst, which can be used to detect glucose. Under the optimal reaction conditions, a linear correlation was established between fluorescence intensity ratio I₀/I and concentration of H₂O₂ from 1.8 × 10⁻⁷ to 9 × 10⁻⁴ mol/L with a detection limit of 1.8 × 10⁻⁸ mol/L. And a linear correlation was established between fluorescence intensity ratio I₀/I and concentration of glucose from 1.6 × 10⁻⁶ to 1.6 × 10⁻⁴ mol/L with a detection limit of 1.0 × 10⁻⁶ mol/L. The proposed method was applied to the determination of glucose in human serum samples with satisfactory results.     

Graphene–palladium nanowires based electrochemical sensor using ZnFe2O4–graphene quantum dots as an effective peroxidase mimic

We proposed an electrochemical DNA sensor by using peroxidase-like magnetic ZnFe₂O₄–graphene quantum dots (ZnFe₂O₄/GQDs) nanohybrid as a mimic enzymatic label. Aminated graphene and Pd nanowires were successively modified on glassy carbon electrode, which improved the electronic transfer rate as well as increased the amount of immobilized capture ssDNA (S1). The nanohybrid ZnFe₂O₄/GQDs was prepared by assembling the GQDs on the surface of ZnFe₂O₄ through a photo-Fenton reaction, which was not only used as a mimic enzyme but also as a carrier to label complementary ssDNA (S3). By synergistically integrating highly catalytically activity of nano-sized GQDs and ZnFe₂O₄, the nanohybrid possessed highly-efficient peroxidase-like catalytic activity which could produce a large current toward the reduction of H₂O₂ for signal amplification. Thionine was used as an excellent electron mediator. Compared with traditional enzyme labels, the mimic enzyme ZnFe₂O₄/GQDs exhibited many advantages such as environment friendly and better stability. Under the optimal conditions, the approach provided a wide linear range from 10⁻¹⁶ to 5 × 10⁻⁹ M and low detection limit of 6.2 × 10⁻¹⁷ M. The remarkable high catalytic capability could allow the nanohybrid to replace conventional peroxidase-based assay systems. The new, robust and convenient assay systems can be widely utilized for the identification of other target molecules.