Effect of capping and particle size on Raman laser-induced degradation of γ-Fe2O3 nanoparticles

Diol capped γ-Fe₂O₃ nanoparticles are prepared from ferric nitrate by refluxing in 1,4-butanediol (9.5 nm) and 1,5-pentanediol (15 nm) and uncapped particles are prepared by refluxing in 1,2-propanediol followed by sintering the alkoxide formed. X-ray diffraction (XRD) shows that all the samples have the spinel phase. Raman spectroscopy shows that the samples prepared in 1,4-butanediol and 1,5-pentanediol and 1,2-propanediol (sintered at 573 and 673 K) are γ-Fe₂O₃ and the 773 K-sintered sample is Fe₃O₄. Raman laser studies carried out at various laser powers show that all the samples undergo laser-induced degradation to α-Fe₂O₃ at higher laser power. The capped samples are however, found more stable to degradation than the uncapped samples. The stability of γ-Fe₂O₃ sample with large particle size (15.4 nm) is more than the sample with small particle size (10.2 nm). Fe₃O₄ having a particle size of 48 nm is however less stable than the smaller γ-Fe₂O₃ nanoparticles.     

A surface-enhanced Raman scattering method for detection of trace glutathione on the basis of immobilized silver nanoparticles and crystal violet probe

Unsatisfactory sensitivity and stability for molecules with low polarizability is still a problem limiting the practical applications of surface-enhanced Raman scattering (SERS) technique. By preparing immobilized silver nanoparticles (Fe₃O₄/Ag) through depositing silver on the surface of magnetite particles, a highly sensitive and selective SERS method for the detection of trace glutathione (GSH) was proposed on the basis of a system of Fe₃O₄/Ag nanoparticles and crystal violet (CV), in which the target GSH competed with the CV probe for the adsorption on the Fe₃O₄/Ag nanoparticles. Raman insensitive GSH replaced the highly Raman sensitive CV adsorbed on the surface of Fe₃O₄/Ag particles. This replacement led to a strong decrease of the CV SERS signal, which was used to determine the concentration of GSH. Under optimal conditions, a linear response was established between the intensity decrease of the CV SERS signal and the GSH concentration in the range of 50–700 nmol L⁻¹ with a detection limit of 40 nmol L⁻¹. The use of a Fe₃O₄/Ag substrate provided not only a great SERS enhancement but also a good stability, which guarantees the reproducibility of the proposed method. Its use for the determination of GSH in practical blood samples and cell extract yielded satisfactory results.     

Hydrogen production from water decomposition by redox of Fe2O3 modified with single- or double-metal additives

Iron oxide modified with single- or double-metal additives (Cr, Ni, Zr, Ag, Mo, Mo-Cr, Mo-Ni, Mo-Zr and Mo-Ag), which can store and supply pure hydrogen by reduction of iron oxide with hydrogen and subsequent oxidation of reduced iron oxide with steam (Fe₃O₄ (initial Fe₂O₃)+4H₂↔3Fe+4H₂O), were prepared by impregnation. Effects of various metal additives in the samples on hydrogen production were investigated by the above-repeated redox. All the samples with Mo additive exhibited a better redox performance than those without Mo, and the Mo-Zr additive in iron oxide was the best effective one enhancing hydrogen production from water decomposition. For Fe₂O₃-Mo-Zr, the average H₂ production temperature could be significantly decreased to 276 °C, the average H₂ formation rate could be increased to 360.9-461.1 μmol min⁻¹ Fe-g⁻¹ at operating temperature of 300 °C and the average storage capacity was up to 4.73 wt% in four cycles, an amount close to the IEA target.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.     

Synthesis and characterization of Fe2O3/SiO2 nanocomposites

Fe₂O₃/SiO₂ nanocomposites based on fumed silica A-300 (S_BET = 337 m²/g) with iron oxide deposits at different content were synthesized using Fe(III) acetylacetonate (Fe(acac)₃) dissolved in isopropyl alcohol or carbon tetrachloride for impregnation of the nanosilica powder at different amounts of Fe(acac)₃ then oxidized in air at 400–900 °C. Samples with Fe(acac)₃ adsorbed onto nanosilica and samples with Fe₂O₃/SiO₂ including 6–17 wt% of Fe₂O₃ were investigated using XRD, XPS, TG/DTA, TPD MS, FTIR, AFM, nitrogen adsorption, Mössbauer spectroscopy, and quantum chemistry methods. The structural characteristics and phase composition of Fe₂O₃ deposits depend on reaction conditions, solvent type, content of grafted iron oxide, and post-reaction treatments. The iron oxide deposits on A-300 (impregnated by the Fe(acac)₃ solution in isopropanol) treated at 500–600 °C include several phases characterized by different nanoparticle size distributions; however, in the case of impregnation of A-300 by the Fe(acac)₃ solution in carbon tetrachloride only α-Fe₂O₃ phase is formed in addition to amorphous Fe₂O₃. The Fe₂O₃/SiO₂ materials remain loose (similar to the A-300 matrix) at the bulk density of 0.12–0.15 g/cm³ and S_BET = 265–310 m²/g.     

High-pressure transitions in MgAl2O4 and a new high-pressure phase of Mg2Al2O5

Phase transitions in MgAl₂O₄ were examined at 21-27 GPa and 1400-2500 °C using a multianvil apparatus. A mixture of MgO and Al₂O₃ corundum that are high-pressure dissociation products of MgAl₂O₄ spinel combines into calcium-ferrite type MgAl₂O₄ at 26-27 GPa and 1400-2000 °C. At temperature above 2000 °C at pressure below 25.5 GPa, a mixture of Al₂O₃ corundum and a new phase with Mg₂Al₂O₅ composition is stable. The transition boundary between the two fields has a strongly negative pressure-temperature slope. Structure analysis and Rietveld refinement on the basis of the powder X-ray diffraction profile of the Mg₂Al₂O₅ phase indicated that the phase represented a new structure type with orthorhombic symmetry (Pbam), and the lattice parameters were determined as a=9.3710(6) Å, b=12.1952(6) Å, c=2.7916(2) Å, V=319.03(3) Å³, Z=4. The structure consists of edge-sharing and corner-sharing (Mg, Al)O₆ octahedra, and contains chains of edge-sharing octahedra running along the c-axis. A part of Mg atoms are accommodated in six-coordinated trigonal prism sites in tunnels surrounded by the chains of edge-sharing (Mg, Al)O₆ octahedra. The structure is related with that of ludwigite (Mg, Fe²⁺)₂(Fe³⁺, Al)(BO₃)O₂. The molar volume of the Mg₂Al₂O₅ phase is smaller by 0.18% than sum of molar volumes of 2MgO and Al₂O₃ corundum. High-pressure dissociation to the mixture of corundum-type phase and the phase with ludwigite-related structure has been found only in MgAl₂O₄ among various A²⁺B³⁺₂O₄ compounds.     

Pressure-induced phase transitions in Al2(WO4)3

The high pressure behavior of aluminum tungstate [Al₂(WO₄)₃] has been investigated up to ∼18 GPa with the help of Raman scattering studies. Our results confirm the recent observations of two reversible phase transitions below 3 GPa. In addition, we find that this compound undergoes two more phase transitions at ∼5.3 and ∼6 GPa before transforming irreversibly to an amorphous phase at ∼14 GPa.     

Ag/PANI/Fe_2O_3复合纳米粒子的合成与催化性能

借助于PANI的还原性质,PANI/Fe2O3复合载体与AgNO3发生表面氧化还原反应,合成了Ag/PANI/Fe2O3复合纳米粒子。TEM和XRD结果表明,立方晶系纳米银的平均粒径10nm。FTIR结果表明,Ag与PANI及Fe2O3复合载体之间不存在化学键合作用,但由于PANI与Ag之间的电子相互作用,Ag/PANI/Fe2O3复合纳米粒子的FTIR吸收峰发生蓝移。Ag/PANI/Fe2O3复合纳米粒子对于间硝基苯磺酸钠的硼氢化钠还原反应表现出良好的催化活性,30min内间硝基苯磺酸钠的转化率达到86.77%。     

Sol-gel synthesized semiconducting LaCo0.8Fe0.2O3-based powder for thick film NH3 gas sensor

Perovskite type LaCo_xFe_1−xO₃ nanoparticles was synthesized by a sol-gel citrate method. The structural, electrical and sensing characteristics of the LaCo_xFe_1−xO₃ system were investigated. The structural characteristics were performed by using X-ray diffraction (XRD) and transmission electron microscopy (TEM) to examine the phase and morphology of the resultant powder. The XRD pattern shows nanocrystalline solid solution of LaCo_xFe_1−xO₃ with perovskite phase. Electrical properties of synthesized nanoparticles are studied by DC conductivity measurement. The sensor shows high response towards ammonia gas in spite of other reducing gases when x = 0.8. The effect of 0.3 wt.% Pd-doped LaCo_0.8Fe_0.2O₃ on the response and a recovery time was also addressed.     

A new 2212-type stair like structure: Bi14Sr21Fe12O61, m=5 member of the generic [Bi2Sr3Fe2O9]m[Bi4Sr6Fe2O16] family

A new oxide, Bi₁₄Sr₂₁Fe₁₂O_61, with a layered structure derived from the 2212 modulated type structure Bi₂Sr₃Fe₂O₉, was isolated. It crystallizes in the I2 space group, with the following parameters: a=16.58(3) Å, b=5.496(1) Å, c=35.27(2) Å and β=90.62°. The single crystal X-ray structure determination, coupled with electron microscopy, shows that this ferrite is the m=5 member of the [Bi₂Sr₃Fe₂O₉]_m[Bi₄Sr₆Fe₂O₁₆] collapsed family. This new collapsed structure can be described as slices of 2212 structure of five bismuth polyhedra thick along , shifted with respect to each other and interconnected by means of [Bi₄Sr₆Fe₂O₁₆] slices. The latter are the place of numerous defects like iron or strontium for bismuth substitution; they can be correlated to intergrowth defects with other members of the family.     

Raman investigations of SERS activity of Ag nanoclusters on a TiO2-nanotubes/Ti substrate

Tubular arrays of TiO₂ nanotubes (ranging in diameter from 40 to 110 nm) on a Ti substrate were used as a support for Ag deposits obtained by the sputter deposition technique where the amount of Ag varied from 0.01 to 0.2 mg Ag/cm². Those composite supports were intended for surface-enhanced Raman scattering (SERS) investigations. Composite samples of Ag/TiO₂ nanotube/Ti were studied with the aid of scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) to reveal their characteristic morphological and chemical features. Raman spectra of pyridine (as a probe molecule) were measured at different cathodic potentials ranging from −0.2 down to −1.2 V after the pyridine had been adsorbed on the Ag-covered TiO₂ nanotube/Ti substrates. In addition, SERS spectra on a bulk standard activated Ag substrate were also measured.The SERS activity of the composite samples was strongly dependent on the amount of Ag deposit. At and above 0.06 mg Ag/cm², the SERS signal was even higher than that for the Ag reference substrate. The high activity of the composites is mainly a result of their specific morphology. The high SERS sensitivity on the surface morphology made it possible to monitor very small temporal changes in the Ag clusters. This rearrangement was not detectable with microscopic (SEM) or microanalytical (AES) methods.     

Synthesis of SiO2/Y2O3:Eu core-shell materials and hollow spheres

The SiO₂/Y₂O₃:Eu core-shell materials and hollow spheres were first synthesized by a template-mediated method. X-ray diffraction patterns indicated that the broadened diffraction peaks result from nanocrystals of Y₂O₃:Eu shells and hollow spheres. X-ray photoelectron spectra showed that the Y₂O₃:Eu shells are linked with silica cores by Si-O-Y chemical bond. SEM and TEM observations showed that the size of SiO₂/Y₂O₃:Eu core-shell structure is in the range of 140-180 nm, and the thickness of Y₂O₃:Eu hollow spherical shell is about 20-40 nm. The photoluminescence spectra of SiO₂/Y₂O₃:Eu core-shell materials and Y₂O₃:Eu hollow spheres have better red luminescent properties, and the broadened emission bands came from the size effects of nanocrystals composed of Y₂O₃:Eu shell.     

Synthesis, crystal structure, infrared and Raman spectra of Sr4Cu3(AsO4)2(AsO3OH)4·3H2O and Ba2Cu4(AsO4)2(AsO3OH)3

The two new compounds, Sr₄Cu₃(AsO₄)₂(AsO₃OH)₄·3H₂O (1) and Ba₂Cu₄(AsO₄)₂(AsO₃OH)₃(2), were synthesized under hydrothermal conditions. They represent previously unknown structure types and are the first compounds synthesized in the systems SrO/BaO-CuO-As₂O₅-H₂O. Their crystal structures were determined by single-crystal X-ray diffraction [space group C2/c, a=18.536(4) Å, b=5.179(1) Å, c=24.898(5) Å, β=93.67(3)°, V=2344.0(8) Å³, Z=4 for 1; space group P4₂/n, a=7.775(1) Å, c=13.698(3) Å, V=828.1(2) Å³, Z=2 for 2]. The crystal structure of 1 is related to a group of compounds formed by Cu²⁺-(XO₄)³⁻ layers (X=P⁵⁺, As⁵⁺) linked by M cations (M=alkali, alkaline earth, Pb²⁺, or Ag⁺) and partly by hydrogen bonds. In 1, worth mentioning is the very short hydrogen bond length, D···A=2.477(3) Å. It is one of the examples of extremely short hydrogen bonds, where the donor and acceptor are crystallographically different. Compound 2 represents a layered structure consisting of Cu₂O₈ centrosymmetric dimers crosslinked by As1φ₄ tetrahedra, where φ is O or OH, which are interconnected by Ba, As2 and hydrogen bonds to form a three-dimensional network. The layers are formed by Cu₂O₈ centrosymmetric dimers of CuO₅ edge-sharing polyhedra, crosslinked by As1O₄ tetrahedra. Vibrational spectra (FTIR and Raman) of both compounds are described. The spectroscopic manifestation of the very short hydrogen bond in 1, and ABC-like spectra in 2 were discussed.     

Kinetic analysis of the thermal stability of lithium silicates (Li4SiO4 and Li2SiO3)

The kinetics describing the thermal decomposition of Li₄SiO₄ and Li₂SiO₃ have been analysed. While Li₄SiO₄ decomposed on Li₂SiO₃ by lithium sublimation, Li₂SiO₃ was highly stable at the temperatures studied. Li₄SiO₄ began to decompose between 900 and 1000 °C. However, at 1100 °C or higher temperatures, Li₄SiO₄ melted, and the kinetic data of its decomposition varied. The activation energy of both processes was estimated according to the Arrhenius kinetic theory. The energy values obtained were −408 and −250 kJ mol⁻¹ for the solid and liquid phases, respectively. At the same time, the Li₄SiO₄ decomposition process was described mathematically as a function of a diffusion-controlled reaction into a spherical system. The activation energy for this process was estimated to be −331 kJ mol⁻¹. On the other hand, Li₂SiO₃ was not decomposed at high temperatures, but it presented a very high preferential orientation after the heat treatments.     

Growth of single crystalline dendritic Li2SiO3 arrays from LiNO3 and mesoporous SiO2

A solution based wet chemistry approach has been developed for synthesizing Li₂SiO₃ using LiNO₃ and mesoporous silica as starting materials at 550 °C. A reaction path where NO and O₂ are formed as side-products is proposed. The crystals synthesized exhibit dendritic growth where the as-prepared nanodendrite is a typical 1-fold nanodendrite composed of one several microns long and some tenth of nanometers wide trunk with small branches, which are several hundreds of nanometers long and up to 70 nm in diameter. The effect of the structure of the mesoporous silica for the final morphology is discussed.     

Ultrasonic-assisted synthesis of PMMA/Ni0.5Zn0.5Fe2O4 nanocomposite in mixed surfactant system

PMMA/Ni_0.5Zn_0.5Fe₂O₄ nanocomposite with superparamagnetic behavior was synthesized by in situ emulsion polymerization of methylmethacrylate (MMA) monomer in the presence of Ni_0.5Zn_0.5Fe₂O₄ colloidal suspension assisted by ultrasonic irradiation. The obtained samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). XRD and FT-IR spectra confirmed the formation of PMMA/Ni_0.5Zn_0.5Fe₂O₄ nanocomposite. TEM images showed that Ni_0.5Zn_0.5Fe₂O₄ nanoparticles with the particle sizes of about 12 nm were well dispersed in the polymer matrix. The nanocomposite at room temperature exhibited superparamagnetic behavior under applied magnetic field. The formation mechanism of PMMA/Ni_0.5Zn_0.5Fe₂O₄ nanocomposite was proposed as well.     

Polythiophene-coated Fe3O4 superparamagnetic nanocomposite: Synthesis and application as a new sorbent for solid-phase extraction

In the present work, a novel type of superparamagnetic nanosorbent, polythiophene-coated Fe₃O₄ nanoparticles (Fe₃O₄@PTh NPs), have been successfully synthesized. The synthesized NPs were characterized by scanning electron microscopy (SEM), Fourier transform-infrared (FT-IR) spectroscopy, and thermal gravimetric analysis (TGA). The synthesized Fe₃O₄@PTh NPs were applied as an efficient sorbent for extraction and preconcentration of several typical plasticizer compounds (di-n-butyl phthalate (DBP), di-(2-ethylhexyl) phthalate (DEHP), and dioctyl adipate (DOA)) from environmental water samples. Separation of Fe₃O₄@PTh NPs from the aqueous solution was simply achieved by applying external magnetic field. Separation and determination of the extracted plasticizers was performed by gas chromatography–flame ionization detection (GC–FID). Several variables affecting the extraction efficiency of the analytes i.e., amount of NPs sorbent, salt concentration, extraction time, and desorption conditions were investigated and optimized. The best working conditions were as follows: amount of sorbent, 100 mg; NaCl concentration, 30% (w/v); sample volume, 45 mL; extraction time, 10 min; and 100 μL of ethyl acetate for desorption of the analytes within 2 min. Under optimized conditions, preconcentration factors for DBP, DEHP, and DOA were obtained as 86, 194, and 213, respectively. The calibration curves were linear (R² > 0.998) in the concentration range of 0.4–100 μg L⁻¹ for both DEHP and DOA and 0.7–100 μg L⁻¹ for DBP. The limits of detection (LODs) were obtained in the range of 0.2–0.4 μg L⁻¹. The intra-day relative standard deviations (RSDs%) based on four replicates were obtained in the range of 4.0–12.3%. The proposed procedure was applied to analysis of water samples including river water, bottled mineral water, and boiling water exposed to polyethylene container (after cooling) and recoveries between 85 and 99% and RSDs lower than 12.8% were obtained.     

A facile two-step modifying process for preparation of poly(SStNa)-grafted Fe3O4/SiO2 particles

This article reports the synthesis of the poly(sodium 4-styrenesulfonate)-grafted Fe₃O₄/SiO₂ particles via two steps. The first step involved magnetite nanoparticles (Fe₃O₄) homogeneously incorporated into silica spheres using the modified Stöber method. Second, the modified silica-coated Fe₃O₄ nanoparticles were covered with the outer shell of anionic polyelectrolyte by surface-initiated atom transfer radical polymerization. The resulted composites were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive microscopy (EDS), Fourier transform-infrared (FT-IR), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and vibration sample magnetometer (VSM). The XRD results indicated that the surface modified Fe₃O₄ nanoparticles did not lead to phase change compared with the pure Fe₃O₄. TEM studies revealed nanoparticles remained monodisperse. The detection of sulfur and sodium signals was a convincing evidence that sodium 4-styrenesulfonate was grafted onto the surface of the magnetic silica in XPS analysis. Finally, super-paramagnetic properties of the composite particles, and the ease of modifying the surfaces may make the composites of important use in mild separation, enzyme immobilization, etc.     

Preparation of Fe3O4 nanoparticle enclosure hydroxylated multi-walled carbon nanotubes for the determination of aconitines in human serum samples

A magnetic carbon nanomaterial for Fe₃O₄ enclosure hydroxylated multi-walled carbon nanotubes (Fe₃O₄-EC-MWCNTs-OH) was prepared by the aggregating effect of Fe₃O₄ nanoparticle on MWCNTs-OH, and combined with high-performance liquid chromatography (HPLC)/diode array detection (DAD) to determine the aconitines (aconitine, hypaconitine and mesaconitine) in human serum samples. Compared with other extraction modes investigated in experiment, Fe₃O₄-EC-MWCNTs-OH sorbents showed a good affinity to target analytes. Some important parameters that could influence extraction efficiency of aconitines, including the extraction mode, amounts of Fe₃O₄-EC-MWCNTs-OH, pH of sample solution, extraction time, desorption solvent and desorption time, were optimized. Under optimal conditions, the recoveries of spiked serum samples were between 98.0% and 103.0%; relative standard deviations (RSDs) ranged from 0.9% to 6.2%. The correlation coefficients varied from 0.9996 to 0.9998. The limits of detection ranged from 3.1 ng mL⁻¹ to 4.1 ng mL⁻¹ at a signal-to-noise ratio of 3. The experimental results showed that the proposed method was feasible for the analysis of aconitines in serum samples.     

Pressure induced phase transformation in U2O(PO4)2

The high pressure behavior of U₂O(PO₄)₂ has been investigated with the help of Raman scattering and X-ray diffraction measurements up to ∼14 and 6.5 GPa, respectively. The observed changes in the Raman spectra as well as the X-ray diffraction patterns suggest that U₂O(PO₄)₂ undergoes a phase transition at ∼6 GPa to a mixture of a disordered ambient pressure phase and a new high pressure phase. The new phase resembles the triclinic mixed-valence phase of uranium orthophosphate (U(UO₂)(PO₄)₂). On release of pressure the initial phase is not retrieved.