NPE在有序介孔炭上的吸附行为研究

采用有序介孔硅为硬模板制备了具有不同孔径的有序介孔炭(OMCs). 氮气吸附测试表明, 有序介孔炭具有丰富的介孔表面和集中的介孔分布. 以壬基酚聚氧乙烯醚(NPE)为探针分子, 研究了大分子酚类在有序介孔炭上的吸附行为. 吸附研究表明, NPE在有序介孔炭上的吸附满足Langmuir吸附模型. 孔结构分析表明, 大于1.5 nm的孔的表面积是决定NPE吸附量的关键因素, 而有序介孔炭的最可几孔径决定吸附速率的大小. 与吸附量相比, 吸附速率更容易受环境温度的影响. 动力学研究表明, NPE在有序介孔炭上的吸附满足准二级动力学方程.     

NPE在有序介孔炭上的吸附行为研究

采用有序介孔硅为硬模板制备了具有不同孔径的有序介孔炭(OMCs). 氮气吸附测试表明, 有序介孔炭具有丰富的介孔表面和集中的介孔分布. 以壬基酚聚氧乙烯醚(NPE)为探针分子, 研究了大分子酚类在有序介孔炭上的吸附行为. 吸附研究表明, NPE在有序介孔炭上的吸附满足Langmuir吸附模型. 孔结构分析表明, 大于1.5 nm的孔的表面积是决定NPE吸附量的关键因素, 而有序介孔炭的最可几孔径决定吸附速率的大小. 与吸附量相比, 吸附速率更容易受环境温度的影响. 动力学研究表明, NPE在有序介孔炭上的吸附满足准二级动力学方程.     

EDLC用分级孔炭电极材料的制备与超电容性能研究

采用有机-有机自组装法和化学活化法相结合,制备了分级孔炭电极材料(HPC)。氮气静态吸附测试表明,化学活化使介孔炭的孔壁上产生了大量的微孔,从而使其比表面积大大增加。与以硬模板法制备的有序介孔炭(OMC)相比,HPC比OMC具有更为优异的电化学性能,这是因为微孔和介孔直接相连的分级孔结构,不仅增大了比表面积,而且能够显著减小电解质离子在电极材料孔道内的扩散阻力。     

新型功能介孔吸附剂NiNb_2O_6的合成及其吸附性能研究

通过柠檬酸溶胶-凝胶反应,合成了新型功能介孔NiNb2O6吸附剂,通过X-射线粉末衍射仪(XRD)、透射电镜(TEM)和比表面积及孔径分析(BET)对其结构进行表征。通过影响因素实验、吸附动力学实验和等温吸附实验,探讨了NiNb2O6吸附剂对水溶液中亚甲基蓝的吸附性能和机理。结果表明,NiNb2O6介孔吸附剂具有正交相晶体结构,平均粒径为30~200nm,比表面积为66.3m2/g。吸附剂用量、温度和pH值均对吸附行为有一定的影响;在35℃时,亚甲基蓝在吸附剂上吸附行为符合Langmuir方程,吸附动力学符合拟二级动力学方程,初始浓度为40mg/L,pH值为7.03时,0.2g介孔吸附剂NiNb2O6对亚甲基蓝的吸附量最大,吸附过程中液膜扩散为主要速率控制步骤。     

三维全碳多孔结构对亚甲基蓝吸附性能的动力学探究

采用低温-烧结法,以碳纳米管(CNTs)为基本骨架,聚甲基丙烯酸甲酯(PMMA)微球为造孔剂,制备了一种孔径可调的三维全碳多孔结构(ACPs);利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射分析(XRD)、拉曼光谱(Raman)、比表面积及孔结构分析等对ACPs的形貌、组成、结构及比表面积进行了表征;考察了ACPs对模拟污染物亚甲基蓝的吸附效果.结果表明,该ACPs为内部含有大孔、介孔及微孔的三维连通孔隙结构,具有较大的比表面积.ACPs对亚甲基蓝的吸附过程符合伪二级动力学模型,对亚甲基蓝的平衡吸附量qe与亚甲基蓝溶液的平衡浓度ce的关系满足Langmuir等温吸附模型,由Langmuir模型计算得到ACPs对亚甲基蓝的最大吸附容量为151.3 mg/g.     

染料在剑麻基活性碳纤维上吸附速度的研究

本文研究了单组分染料在活性碳纤维上的吸附速度及双组分染料的竞争吸附速度。研究结果表明,不同染料分子在ＳＡＣＦ上吸附速度差异较大,结晶紫的吸附速度比亚甲基蓝或铬蓝黑Ｒ慢行多。亚甲基蓝和铬蓝黑Ｒ双组分共存时,其吸附速度与单组分时的相近,但初始阶段亚甲基蓝的吸附比铬蓝黑Ｒ快得多。由于染料的分子尺寸与ＡＣＦ的微孔大小相近,染料在活性碳纤维上的七染料孤及活怀碳纤维的孔结构密切相关。因此,不同染料分子在ＡＣＦ     

多阶有序多孔炭的软模板法合成与结构控制

多阶有序多孔炭材料综合了多种多孔炭材料的结构优点,在催化、吸附、储能、电化学等方面具有潜在的重要应用。多阶有序多孔炭材料的合成方法很多,到目前为止,模板法是控制孔结构和调节尺寸的最有效方法。在模板法中,软模板法因为其工艺简单、省时、成本低、环境污染小等优势,近些年来广泛被人们采用。用软模板法合成的多阶有序多孔炭包括:大孔-介孔炭,介孔-微孔炭,介孔-介孔炭,大孔-介孔-微孔炭等。本文对多阶有序多孔炭的软模板法合成与结构控制进行了综述。总结了软模板法在实现上述材料孔结构控制中的影响因素。     

磁性有序介孔炭的制备及药物吸附行为研究

采用纳米共铸法将磁性纳米粒子包埋到有序介孔炭的骨架中, 制成含有磁性纳米粒子的有序介孔炭(Fe/OMCs). 实验通过氮气吸附、扫描电镜、X射线衍射、磁性测试等手段对Fe/OMCs进行了系统的表征. 研究表明, Fe/OMCs基本保持了有序介孔结构, 磁性粒子在材料中以纳米α-Fe粒子的形式存在, 并且具有超顺磁特性. 盐酸四环素(TH)在Fe/OMCs上的吸附研究表明, Fe/OMCs的介孔表面积和介孔孔容是决定TH吸附量的关键因素. 脱附动力学研究表明, Fe/OMCs的孔尺寸是影响脱附速率的关键因素, 孔径越大, TH的脱附速率就越大.     

以铬皮为原料制备多孔炭及其对亚甲基蓝的吸附性能研究

以铬皮为原料制备多孔炭,并考察其对亚甲基蓝染料的吸附性能,对其吸附机理进行了探讨。结果表明,体系pH、亚甲基蓝初始浓度和吸附时间对多孔炭吸附亚甲基蓝的能力影响较大。通过吸附等温线和吸附动力学研究,发现该吸附过程可用Langmuir吸附等温线来描述,且符合准二级动力学吸附模型。铬皮基多孔炭有望成为含亚甲基蓝污水处理的良好净化剂。     

掺杂铜的介孔SiO2微球的制备以及对亚甲基蓝的吸附

通过水热法在室温下合成了不同铜含量的介孔SiO2微球(Cu-MSM)。目的在于研究吸附剂量、MB的初始浓度以及吸附时间对Cu-MSM从溶液中移除亚甲基蓝(MB)吸附性能的影响。结果表明,当增加Cu-MSM的量时,MB的去除率会大大提高;掺杂铜的介孔SiO2微球可以通过吸附去除水溶液中的亚甲蓝。最后,简要探讨了亚甲基蓝的吸附机理。     

Aqueous dye adsorption on ordered mesoporous carbons

Ordered mesoporous carbons (OMCs) with varying pore size, and microporous carbon, CFY, were synthesized using ordered mesoporous silica SBA-15 and NaY zeolite as hard templates, respectively. N(2) adsorption tests show that the synthesized OMCs possess abundant mesopores and centralized mesopore distribution. Methylene blue (MB) and neutral red (NR) were used as probe molecules to investigate their adsorption behaviors on OMCs and CFY. As evidenced by adsorption tests, the volume of mesopores of which the pore size is larger than 3.5 nm is a crucial factor for the adsorption capacity and adsorption rate of MB on OMCs. However, the most probable pore diameter of OMCs was found to be vital to the adsorption capacity and adsorption rate of NR. Theoretical studies show that the adsorption kinetics of MB and NR on OMCs can be well depicted by using pseudo-second-order kinetic model.     

Adsorption of bulky molecules of nonylphenol ethoxylate on ordered mesoporous carbons

Ordered mesoporous carbons (OMCs) with varying pore sizes were prepared using ordered mesoporous silica SBA-15 as hard templates. The OMCs possess abundant mesopores with narrow pore size distribution, on which the adsorption behavior of bulky molecules of nonylphenol ethoxylate (NPE) were investigated. The isotherms of NPE on OMCs can be fitted by Langmuir adsorption model, evidenced by the adsorption data. The surface area of the pores larger than 1.5 nm is a crucial factor to the adsorption capacity of NPE, whereas the most probable pore diameter of OMCs is crucial to the adsorption rate of NPE. The adsorption temperature has more significant effects on adsorption rate than the adsorption capacity. Theoretical studies show that the adsorption kinetics of NPE on OMCs can be depicted with the pseudo-second-order kinetic model. In addition, thermodynamic parameters of adsorption were evaluated based on the equilibrium constants related to the equilibrium of adsorption at different temperatures.     

Organic acid-assisted soft-templating synthesis of ordered mesoporous carbons

A series of soft-templated ordered mesoporous carbons (OMCs) was synthesized by using resorcinol and formaldehyde as carbon precursors, triblock copolymer Pluronic F127 as a soft-template, and an organic acid (acetic, benzoic, citric, oxalic, or succinic) as a polymerization reaction catalyst. The aforementioned organic acids were strong enough to facilitate the formation of ordered mesophases by the block copolymer template used and to catalyze the polymerization reaction of resorcinol and formaldehyde in this template. The use of weak organic acids instead of strong inorganic acids such as HCl eliminated inorganic anions from the reaction environment and resulted in high surface area OMCs. Basically, the resulting carbons showed the surface areas and pore volumes comparable to those reported for the carbons prepared under similar conditions but in the presence of strong inorganic acids. Electron microscopy analysis proved the presence of ordered mesopores, whereas thermogravimetric analysis showed a good thermal stability of these carbons.     

Electrochemical Oxidation and Detection of Morphine at Ordered Mesoporous Carbon Modified Glassy Carbon Electrodes

In this work, three ordered mesoporous carbons (OMCs) with different structural parameters were synthesized by a simple variation of the hydrothermal temperature of the silica templates (SBA‐15). X‐ray diffraction and nitrogen adsorption‐desorption results show these OMCs exhibit an ordered 2D hexagonal mesostructure with tunable pore diameter. OMC‐modified glassy carbon electrodes exhibit efficient electrocatalytic reactivity toward oxidation of morphine (MO). The amperometric detection of MO in pH 7.0 phosphate buffered saline at +0.39 V versus Ag/AgCl is the lowest potential reported to‐date. A linear range from 0.2 to 197.6 μM and a detection limit of 0.03 μM MO were obtained.     

Synthesis of mesoporous carbons using ordered and disordered mesoporous silica templates and polyacrylonitrile as carbon precursor

Mesoporous carbons were synthesized from polyacrylonitrile (PAN) using ordered and disordered mesoporous silica templates and were characterized using transmission electron microscopy (TEM), powder X-ray diffraction, nitrogen adsorption, and thermogravimetry. The pores of the silica templates were infiltrated with carbon precursor (PAN) via polymerization of acrylonitrile from initiation sites chemically bonded to the silica surface. This polymerization method is expected to allow for a uniform filling of the template with PAN and to minimize the introduction of nontemplated PAN, thus mitigating the formation of nontemplated carbon. PAN was stabilized by heating to 573 K under air and carbonized under N2 at 1073 K. The resulting carbons exhibited high total pore volumes (1.5-1.8 cm3 g(-1)), with a primary contribution of the mesopore volume and with relatively low microporosity. The carbons synthesized using mesoporous templates with a 2-dimensional hexagonal structure (SBA-15 silica) and a face-centered cubic structure (FDU-1 silica) exhibited narrow pore size distributions (PSDs), whereas the carbon synthesized using disordered silica gel template had broader PSD. TEM showed that the SBA-15-templated carbon was composed of arrays of long, straight, or curved nanorods aligned in 2-D hexagonal arrays. The carbon replica of FDU-1 silica appeared to be composed of ordered arrays of spheres. XRD provided evidence of some degree of ordering of graphene sheets in the carbon frameworks. Elemental analysis showed that the carbons contain an appreciable amount of nitrogen. The use of our novel infiltration method and PAN as a carbon precursor allowed us to obtain ordered mesoporous carbons (OMCs) with (i) very high mesopore volume, (ii) low microporosity, (iii) low secondary mesoporosity, (iv) large pore diameter (8-12 nm), and (v) semi-graphitic framework, which represent a desirable combination of features that has not been realized before for OMCs.     

Nonenzymatic amperometric sensor of hydrogen peroxide and glucose based on Pt nanoparticles/ordered mesoporous carbon nanocomposite

A simple and facile synthetic method to incorporate Pt nanoparticles inside the mesopores of ordered mesoporous carbons (OMCs) is reported. The Pt/OMCs nanocomposite was characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and nitrogen adsorption-desorption. The results show that the incorporation of Pt nanoparticles inside the pores of OMCs does not change the highly ordered two-dimensional hexagonal mesostructure of OMCs matrix. Nonenzymatic amperometric sensor of hydrogen peroxide and glucose based on the Pt/OMCs nanocomposite-modified glassy carbon (GC) electrode is developed. Compared with the original OMCs-modified electrode, the Pt/OMCs-modified electrode displays improved current response towards hydrogen peroxide and gives linear range from 2 to 4212 μM. At an applied potential of −0.08 V, the Pt/OMCs nanocomposite gives linearity in the range of 0.5-4.5 mM glucose in neutral buffered saline solution. This glucose sensor also exhibits good ability of anti-interference to electroactive molecules. The combination the unique properties of Pt nanoparticles and the ordered mesostructure of OMCs matrix guarantees the enhanced response for hydrogen peroxide and glucose.     

孔径渐变的有序介孔炭的合成及电化学应用

以SBA-15为模板,硼酸为孔道扩张剂,蔗糖为碳源制备了一系列孔径渐变的有序硼杂介孔炭材料,并研究了其电化学电容性能。氮气静态吸附测试表明,当硼酸物质的量分数从0%增大到75%时,介孔炭的孔径从3.3nm增大至8.1nm,并保持有序的介孔结构。电化学测试表明,在KOH电解液中,硼杂介孔炭比电容明显高于未掺杂硼有序介孔炭,孔道有序性和孔径大小共同影响了炭材料的电容性能。当硼酸物质的量分数为50%时,炭材料的比电容性能最优。     

Surface functionalization of ordered mesoporous carbons--a comparative study

Hexagonally structured mesoporous carbons C15 and CMK-5 and cubically structured carbon C48 were synthesized using ordered silica SBA-15 and MCM-48 as templates and carbon precursors of different structures. The surfaces of these ordered carbons were chemically functionalized by employing an approach, in which the selected diazonium compounds were in situ generated and reacted with the carbon frameworks of the mesoporous carbons. The aromatic organic molecules containing chlorine, ester, and alkyl groups were covalently attached to the surface of these ordered mesoporous carbons. The presence of functional groups on the modified carbons was confirmed with Fourier transform infrared spectroscopy, thermogravimetric analysis, and nitrogen adsorption. The BET-specific surface area and the pore width of ordered carbons were significantly reduced, whereas the primary structure of these ordered carbons and their unit cells were intact. Basically, the density of grafted functional groups is related to the specific surface area of the sample, particularly the surface area of mesopores. The surface functionalization reaction takes place only on the external surface of carbon C15, while it occurs on both of the internal and external surface of CMK-5 carbon with the nanopipe structure. The presence of the micropores in CMK-5 carbon should be responsible for its lower grafting density because the small micropores are inaccessible in the reaction. It was also proposed that the preferred adsorption/reaction in C48 may be related to the observed unsymmetrical degradation of the XRD patterns for the functionalized C48 samples. The chemical modification process considerably reduced the primary mesopores in these ordered carbons by approximately 1-1.5 nm, affording carbons with micropores in the cases of C15 and C48, and mixed micropores and small mesopores in the case of CMK-5. A grafting density of approximately 0.9-1.5 micromol/m(2) was achieved under current research.