Spectrophotometric determination of nitrite based on its catalytic effect on the oxidation of carminic acid by bromate

A highly sensitive and selective method is described for the determination of trace amounts of nitrite based on its effect on the oxidation of carminic acid with bromate. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of carminic acid at 490 nm after 3 min of mixing the reagents. The optimum reaction conditions were 1.8×10⁻¹ mol l⁻¹ H₂SO₄, 3.8×10⁻³ mol l⁻¹ KBrO₃, and 1.2×10⁻⁴ mol l⁻¹ carminic acid at 30°C. By using the recommended procedure, the calibration graph was linear from 0.2 to 14 ng ml⁻¹ of nitrite; the detection limit was 0.04 ng ml⁻¹; the R.S.D. for six replicate determinations of 6 ng ml⁻¹ was 1.7%. The method is mostly free from interference, especially from large amounts of nitrate and ammonium ions. The proposed method was applied to the determination of nitrite in rain and river water.     

Sequential injection redox or acid-base titration for determination of ascorbic acid or acetic acid

Two sequential injection titration systems with spectrophotometric detection have been developed. The first system for determination of ascorbic acid was based on redox reaction between ascorbic acid and permanganate in an acidic medium and lead to a decrease in color intensity of permanganate, monitored at 525 nm. A linear dependence of peak area obtained with ascorbic acid concentration up to 1200 mg l⁻¹ was achieved. The relative standard deviation for 11 replicate determinations of 400 mg l⁻¹ ascorbic acid was 2.9%. The second system, for acetic acid determination, was based on acid–base titration of acetic acid with sodium hydroxide using phenolphthalein as an indicator. The decrease in color intensity of the indicator was proportional to the acid content. A linear calibration graph in the range of 2–8% w v⁻¹ of acetic acid with a relative standard deviation of 4.8% (5.0% w v⁻¹ acetic acid, n=11) was obtained. Sample throughputs of 60 h⁻¹ were achieved for both systems. The systems were successfully applied for the assays of ascorbic acid in vitamin C tablets and acetic acid content in vinegars, respectively.     

Simple flow-injection system for the simultaneous determination of nitrite and nitrate in water samples

A novel spectrophotometric reaction system was developed for the determination of nitrite as well as nitrate in water samples, and was applied to a flow-injection analysis (FIA). The spectrophotometric flow-injection system coupled with a copperised cadmium reductor column was proposed. The detection was based on the nitrosation reaction between nitrite ion and phloroglucinol (1,3,5-trihydroxybenzene), a commercially available phenolic compound. Sample injected into a carrier stream was split into two streams at the Y-shaped connector. One of the streams merged directly and reacted with the reagent stream: nitrite ion in the samples was detected. The other stream was passed through the copperised cadmium reductor column, where the reduction of nitrate to nitrite occurred, and the sample zone was then mixed with the reagent stream and passed through the detector: the sum of nitrate and nitrite was detected. The optimised conditions allow a linear calibration range of 0.03–0.30 μg NO₂⁻-N ml⁻¹ and 0.10–1.00 μg NO₃⁻-N ml⁻¹. The detection limits for nitrite and nitrate, defined as three times the standard deviation of measured blanks are 2.9 ng NO₂⁻-N ml⁻¹ and 2.3 ng NO₃⁻-N ml⁻¹, respectively. Up to 20 samples can be analyzed per hour with a relative standard deviation of less than 1.5%. The proposed method could be applied successfully to the simultaneous determination of nitrite and nitrate in water samples.     

A novel method for the spectrophotometric determination of nitrite in water

A rapid, simple, selective and sensitive method for the spectrophotometric determination of nitrite in water has been developed and optimum reaction conditions along with other analytical parameters have been evaluated. Nitrite reacts with barbituric acid in acidic solution to give the nitroso derivative, violuric acid. At analytical wavelength of 310 nm, Beer's law is obeyed over the concentration range 0.00–3.22 ppm of nitrite. The molar absorptivity is 15330 ± 259.7 (95%) with pooled standard deviation of 355.57 and R.S.D. of 2.32%. As well as the method is sensitive (2.99 × 10⁻³ μg NO₂ cm⁻²) and selective, it tolerates most of the potential interferents. It has been successfully applied to nitrite determination in natural waters by use of a calibration graph with determination limit of 1.66 μg NO₂ in 100 mL working solution corresponding to minimum 9.5 ppb NO₂–N in water samples. Lower concentrations of nitrite (3.0 μg NO₂/L sample) is precisely analyzed by using the method of dilution with sample, with R.S.D. of lower than 0.5%. The results were compared with standard N-(1-naphtyl)ethylenediamine dihydrochloride method and very good agreement between the data was observed. The method can easily be applied in the field.     

Indirect kinetic spectrophotometric determination of hydroxylamine based on its reaction with iodate.

A simple, precise and accurate method is proposed for rapid determination of trace amounts of hydroxylamine based on the reaction of hydroxylamine with iodate in acidic media. The reaction of neutral red by the produced nitrite ion was used to monitor the reaction spectrophotometrically at 525 nm by a fixed time method. Hydroxylamine in the range of 0.0400-1.200 microg mL(-1) could be determined. The relative standard deviation for 10 determinations of 0.500 microg mL(-1) hydroxylamine was 1.81% and the limit of detection was 0.010 microg mL(-1). The proposed method was applied to the determination of hydroxylamine in water samples with satisfactory results.     

Application of Ag2X (X = SO3, Cr2O7, C2O4 and CO3) solid-phase reagents for indirect determination of cyanide in the industrial effluent using FIA-FAAS system

Four solid-phase reagents have been tested for indirect determination of cyanide using flow injection analysis-flame atomic absorption spectrometry (FIA-FAAS). The method is based on insertion of aqueous cyanide solutions into an on-line Ag₂X (where X are SO₃²⁻, Cr₂O₇²⁻, C₂O₄²⁻ and CO₃²⁻) packed column (25%, m/m suspended on silica gel beads) and re-distilled water or sodium hydroxide are used as the carrier stream. The eluent containing the analyte as silver cyanide complexes, produced from reaction between Ag₂X and cyanide, measured by flame atomic absorption spectrometry. The method is simple, fast and selective than other published FIA procedures. A relative standard deviation (R.S.D.) better than 1.12% was obtained in a repeatability study. The method was applied to the determination of cyanide in industrial electrolytic baths.     

卟啉在分析化学中的应用(Ⅰ)——四-(4-三甲铵苯基)卟啉吸光光度法测定痕量铜

本文提出以水溶性卟啉α、β、γ、δ-四-(4-三甲铵苯基)叶啉[简称T-(4-TAP)P]作显色剂并研完了T-(4-TAP)P与铜(Ⅱ)的显色反应。试验了21种金属离子及8种盐的干扰,影响均小。提出了吸光光度测定ppb级痕量铜的方法。应用于测定高纯稀土及水样中痕量铜,操作简便快速,结果满意。     

Copper determination in natural water samples by using FAAS after preconcentration onto amberlite XAD-2 loaded with calmagite

A procedure for separation and preconcentration of trace amounts of copper in natural water samples, has been proposed. It is based on the adsorption of copper(II) ions onto a column of Amberlite XAD-2 resin loaded with calmagite reagent. This way amounts of copper within the range from 0.0125 to 25.0 μg, in a sample volume of 25 to 250 ml, and pH from 3.7 to 10.0 was concentrated as calmagite complex in a column of 0.50 g of Amberlite XAD-2 resin. Copper (II) ion was desorpted by using 5.0 ml of 2 mol l⁻¹ hydrochloric acid. Detection and determination limits of the proposed procedure for 250 ml sample volume were 0.15 and 0.50 μg l⁻¹, respectively. Selectivity test showed that (in the indicated concentration), calcium(II) (500 mg l⁻¹), magnesium(II) (500 mg l⁻¹), strontium(II) (50 mg l⁻¹), iron(III) (10 mg l⁻¹), nickel(II) (10 mg l⁻¹), cobalt(II) (10 mg l⁻¹), cadmium(II) (10 mg l⁻¹) and lead(II) (10 mg l⁻¹) did not interfere in copper determination by this procedure. Precision of the method, evaluated as the relative standard deviation by analyzing a series of seven replicates, was 2.42% for a copper mass of 1.0 μg in a sample volume of 100 ml. The accuracy of the proposed procedure was evaluated by means of copper determination in reference biological samples. The achieved results were in good agreement with certified values. The extractor system had a sorption capacity of 1.59 μmol of copper per gram of resin loaded with calmagite. The proposed procedure was applied for copper determination by FAAS in natural water samples. Samples were collected from different places of Salvador city, Bahia, Brazil. The achieved recovery, measured by the standard addition technique, showed that the proposed procedure had good accuracy. A good enrichment factor (50×) and simplicity are the main advantages in this analytical procedure.     

顶空气相色谱法快速测定污水中氨氮含量

研究了一种基于化学反应型顶空气相色谱的快速检测污水氨氮含量新方法。首先在顶空瓶中用过量的甲醛与NH₄⁺反应产生等物质的量的强酸，再用NaHCO₃与新生成的酸反应产生CO₂，最后经过气相色谱定量CO₂，间接得出样品中氨氮的含量。结果表明，氨氮含量与气相色谱信号值之间存在良好的线性相关性，相关系数为0.999，定量限为0.786 mg/L（以N的质量浓度计），相对标准偏差小于2%，加标回收率在95%~105%之间。与国标纳氏试剂法相比，该方法测定结果的相对偏差在±5%以内。该方法检测效率高，适用于快速批量检测污水中氨氮的含量。     

On-line preconcentration of some rare earth elements in water samples using C18-cartridge modified with l-(2-pyridylazo) 2-naphtol (PAN) prior to simultaneous determination by inductively coupled plasma optical emission spectrometry (ICP–OES)

The on-line column preconcentration technique with inductively coupled plasma optical emission spectroscopy (ICP–OES) has been developed using a cartridge filled with octadecyl silica modified by l-(2-pyridylazo) 2-naphtol (PAN). The aim of this method was to determine some rare earth elements (REEs) (Ce, Dy, La, Sm, and Y) and uranium in water samples. Sample solutions were passed through the C₁₈-modified column. The adsorbed cations were subsequently eluted from the column and transferred into the plasma with nitric acid solution for simultaneous determination of them. Sample pH, amount of PAN as a complexing agent, sampling and eluting flowrates and concentration of the eluent were optimized. Detection limits based on three times of standard deviations of blank by 10 replicates were in the range of 11 ng l⁻¹ for Dy to 69 ng l⁻¹ for U. Sample throughput was 10 samples h⁻¹. The proposed method was applied to determine REEs in natural water samples. Recoveries of the REEs from natural water samples were between 95 and 106% with percent relative standard deviation (%R.S.D.) of 1.0–7.9%.     

一种同时测定环己酮肟水解反应中环己酮肟和硫酸羟胺含量的方法

在环己酮肟水解反应制备硫酸羟胺过程中,环己酮肟与产物硫酸羟胺在酸性条件下难以分离,硫酸羟胺的含量测定受到环己酮肟的干扰。 本文采用高效液相色谱法和氧化还原滴定法建立了一种简便、有效的新方法同时测定硫酸羟胺与环己酮肟的含量。 结果表明,在H⁺浓度大于2.4 mol/L,Fe³⁺/环己酮肟摩尔比大于5:1的条件下,环己酮肟和硫酸羟胺测定的标准滴定曲线的线性相关系数分别为0.99998和0.99996,相对标准偏差分别为0.39%和0.50%,水解反应样品的加标回收率为97.1%~100.6%。     

Kinetic spectrophotometric determination of low levels of nitrite by catalytic reaction between pyrogallol red and bromate

A kinetic spectrophotometric method for the determination of trace nitrite (0.003-1.000 microg/ml) based on its catalytic effect on the reaction between potassium bromate and pyrogallol red in acidic media is described. The reaction is monitored spectrophotometrically by measuring the decreasing colour of pyrogallol red at 467 nm by the fixed-time method. At a given time of 3.0 min at 30 degrees, the detection limit is 0.001 microg/ml and the relative standard deviation for 0.010 microg/ml nitrite is 1.8% (n = 8). The method is free from most interferences, especially from large amounts of nitrate and ammonium. The procedure was successfully applied to the determination of trace nitrite in natural water without preconcentration.     

Immobilization enzyme fluorescence capillary analysis for determination of lactic acid

A new method for the determination of lactic acid based on the immobilization enzyme fluorescence capillary analysis (IE-FCA) was proposed. Lactic dehydrogenase (LDH) was immobilized on inner surface of a capillary with glutaraldehyde, and an immobilized enzyme lactate capillary bioreactor (IE-LCBR) was formed for the determination of lactic acid. After nicotinamide adenine dinucleotide (NAD⁺) is mixed with lactic acid solution, it was sucked into the IE-LCBR and was detected at λ_ex 353 nm/λ_em 466 nm. Optimized conditions are as follows: the temperature is 38 °C; the reaction time is 15 min; the concentrations of Tris buffer (pH 8.8) and NAD⁺ are 0.1 mol L⁻¹ and 4 mmol L⁻¹, respectively; the concentration of LDH used for immobilization is 15 kU L⁻¹. The concentration of lactic acid is directly proportional to the fluorescence intensity measured from 0.50 to 2.0 mmol L⁻¹; and the analytical recovery of added lactic acid was 99–105%. The minimum detection limit of the method is 0.40 mmol L⁻¹ and sensitivity of the IE-CBR is 4.6 F mmol⁻¹ L⁻¹ lactate. Its relative standard deviation (R.S.D.) is ≤2.0%. This IE-FCA method was employed for determination of lactate in milk drink.     

Spectrophotometric determination of cadmium with 1-(2-pyridylazo)-2-naphthol and non-ionic surfactants Application to acetic acid extracts of ceramic enamels

The Cd-PAN system in the presence of non-ionic surfactants (polyoxyethylene nonylphenols), which dissolve the reagent and complex by formation of micelles, has been studied spectrophotometrically. The optimum conditions for Cd determination are pH 9 (Na₂B₄O₇-HClO₄), 2% of surfactant and measurement at 555 nm. The complex is Cd(PAN)₂ and its conditional formation constant is 3.5 × 10¹¹. The system obeys the Lambert-Beer law, with an error of 0.9% over the Cd concentration range 0.44–1.74 ppm; the molar absorptivity is 4.94 × 10⁴1·mole⁻¹.cm⁻¹ at 555 nm. The relative standard deviation is 0.7% and the limit of detection 0.009 μg/ml. The selectivity with respect to species important in the ceramic industry is adequate for application of the method to determination of Cd in acetic acid extracts of ceramic enamels.     

基于电化学方法测定饮用水源水中的痕量铜离子

本文建立了一种饮用水源水中痕量溶解态铜离子（Cu²⁺）的定性和定量电化学检测方法. 该方法首先通过电化学循环伏安法于玻碳电极表面制备粒径约为70 nm的金纳米粒子（Au NPs）,然后采用方波阳极溶出伏安法进行待测水样中Cu²⁺的定性定量分析. 研究结果表明,对于标准溶液,方法的检出限为1.3μg·L^-1,线性范围在2 ~ 50μg·L^-1之间,常见重金属离子对其定性定量分析几无影响. 在此基础上,将该方法应用于福建省重要的饮用水源水--闽江中游水样中Cu²⁺的含量分析,所得测试结果与国家标准方法（石墨炉原子吸收光谱法）无显著性差异,标准偏差在20%以内. 本方法具有电极制备简单、测定成本低以及分析快速等优点,进一步优化电极制备方法以提高方法的重现性和定量准确度,将可望用于现场测定各种饮用水源水中的痕量溶解态Cu²⁺.     

Flow-injection spectrophotometry of manganese by catalysis of the periodate oxidation of 2,2'-azinobis(3-ethylbenzothiazoline-6-sulfonic acid)

A sensitive flow-injection spectrophotometric procedure is proposed for the determination of manganese(II), based on its catalytic effect on the oxidation of 2,2′-azinobis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) with periodate. By monitoring the change in absorbance of the oxidation product of ABTS at 415 nm, manganese(II) in the range 0.05–1.0 ng ml⁻¹ can be determined with a sampling frequency of 30 h⁻¹. A relative standard deviation (R.S.D.) (n=10) is 1.6% at the 0.5 ng ml⁻¹ level. The proposed method suffers from few interferences and has been successfully applied to the determination of manganese in river, lake and seashore water samples.     

Coupling of flow injection wetting-film extraction without segmentation and phase separation to flame atomic absorption spectrometry for the determination of trace copper in water samples

A flow injection wetting-film extraction system without segmentor and phase separator has been coupled to flame atomic absorption spectrometry for the determination of trace copper. Isobutyl methyl ketone (MIBK) was selected as coating solvent and 8-hydroxyquinoline (oxine) as the chelating reagent. By switching of a 8-channel valve and alternative initiation of two peristaltic pumps, MIBK, sample solution containing copper chelate of oxine, and air-segment sandwiched eluting solution (1.0 mol l⁻¹ nitric acid) were sequentially aspirated into an extraction coil made of PTFE tubing of 360 cm length and 0.5 mm i.d. The formation of organic film in the wall of the extraction coil, extraction of the copper chelate into the organic film and back-extraction of the analyte into the eluting solution occurred consecutively when these zones aspirated into the extraction coil were propelled down the extraction coil by a carrier solution at a flow rate of 2 ml min⁻¹. After leaving the extraction coil, the concentrated zone was transported to the nebulizer at its free uptake rate for atomization. Under the optimized conditions, an enrichment factor of 43 and a detection limit of 0.2 μg l⁻¹ copper were achieved at a sample throughput rate of 30 h⁻¹. Eleven determinations of a standard copper solution of 60 μg l⁻¹ gave a relative standard deviation of 1.5%. Foreign ions possibly present in tap water and natural water did not interfere with the copper determination. The developed method has been successfully used to the determination of copper content of tap water and river water.     

Correction of iron interface in the spectrophotometric flow injection catalytic determination of molybdenum in plants

Iron interference in the spectrophotometric catalytic determination of molybdenum based on the iodide-hydrogen peroxide reaction can be corrected by using sulphosalicylic acid as masking and color-forming reagent. The catalytic influence of iron ions is circumvented to the extent of about 90% and correction of any remaining iron ions is possible by monitoring the colored iron(III)-salicylate complex at 490 nm. In this way, iron is also determined. With the proposed system, molybdenum can be determined in plant and food digests within the 0–100 μg Mo 1⁻¹ range in the presence of up to 25 mg Fe 1⁻¹, at a sampling rate of about 50 determinations h⁻¹. The relative standard deviation of 10 consecutive measurements was estimated as < 2%. Results for samples were comparable with those obtained by graphite furnace atomic absorption spectrometry. In addition, recoveries within the range 94–100% were calculated.     

Ion chromatography of nitrite at the ppb level with photometric measurement of iodine formed by post-column reaction of nitrite with iodide

The difficulty in ion-chromatographic determination of nitrite in aqueous solutions containing a high concentration of chloride arises mainly from incomplete resolution of the peaks for these anions on the separation column whose efficiency is not high. A photometric measurement of iodine formed by a reaction of nitrite with iodide has been found to make it possible to determine, chromatographically, trace amounts of nitrite without any interference from chloride; chloride does not oxidize iodide to produce iodine. The proposed method was based on the separation of nitrite from matrix anions on a silica-based anion-exchange column with a 1.5·10⁻³ M phthalate eluent (pH 5.0), followed by photometric measurement of the iodine (as triiodide) formed via a post-column reaction of the separated nitrite with iodide. The optimal conditions for the post-column reaction were established by varying the concentrations of iodide, copper(II) and nitric acid in a post-column-reaction solution and the length of a reaction tube. A calibration graph for nitrite, plotted as peak heights versus concentrations, was linear up to 1.50·10⁻⁵ M (690 ppb). The detection limit, defined at S/N=3, was 1.00·10⁻⁷ M (4.60 ppb) nitrite. The presence of chloride ions up to 0.01 M did not give any interference to the determination of nitrite. This method was successfully applied to the determination of nitrite in lake water, river water, sewage works water and snow samples without any pretreatment.     

CuO-nanoparticles modified carbon paste electrode for square wave voltammetric determination of lidocaine: Comparing classical and Box–Behnken optimization methodologies

In this research, copper oxide nanoparticles modified carbon paste electrode was developed for the voltammetric determination of lidocaine. The square wave voltammogram of lidocaine solution showed a well-defined peak between +0.5 and +1.5 V. Instrumental and chemical parameters influencing voltammetric response were optimized by both one at a time and Box–Behnken model of response surface methodology. The results revealed that there was no significant difference between two methods of optimization. The linear range was 1–2500 μmol L~(-1)(Ip= 0.11 C_(LH)+ 17.38, R~2= 0.999). The LOD and LOQ based on three and ten times of the signal to noise(S/N) were 0.39 and 1.3 μmol L~(-1)(n = 10),respectively. The precision of the method was assessed for 10 replicate square wave voltammetry(SWV)determinations each of 0.05, 0.5 and 1 μmol L~(-1) of lidocaine showing relative standard deviations 4.1%,3.7% and 2.1%, respectively. The reliability of the proposed method was established by application of the method for the determination of lidocaine in two pharmaceutical preparations, namely injection and gel.