Crystallization behavior and morphological development of isotactic polypropylene with an aryl amide derivative as β‐form nucleating agent

This article reports crystallization behaviors of isotactic polypropylene (iPP) with an aryl amide derivative (TMB‐5) as β‐form nucleating agent. The effects of nucleating agent concentration, thermal history and assemble morphology of nucleating agent on the crystallization behaviors of iPP were studied by differential scanning calorimetry, X‐ray diffraction, and polarized optical microscopy. The results indicated that the TMB‐5 concentration should surpass a threshold value to get products rich in β‐iPP. The diverse morphologies of TMB‐5 are determined by nucleating agent concentration and crystallization condition. At higher concentrations, the recrystallized TMB‐5 aggregates into needle‐like structure, which induces mixed polymorphic phases on the lateral surface and large amount of β modification around the tip. High β nucleation efficiency was obtained at the lowest studied crystallization temperature, which is desirable for real molding process. TMB‐5 prefers to recrystallize from the melt at higher concentration and lower crystallization temperature. The difference in solubility, pertinent to concentration and crystallization temperature, determined the distinct crystallization behaviors of iPP. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1725–1733, 2008     

Crystallization behavior and morphology of β‐nucleated isotactic polypropylene with different stereo‐defect distribution

Aiming at further investigating the combination effect of concentration of β‐nucleating agent (β‐NA) and stereo‐defect distribution on the crystallization behavior of β‐nucleated isotactic polypropylene (β‐iPP), in this study, the crystallization behavior and polymorphic morphology of twoβ‐iPP resins with nearly same average isotacticity (PP‐A and PP‐B) but different uniformities of stereo‐defect distribution were investigated by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and polarized optical microscopy (POM). The results of DSC and WAXD showed that the addition of TMB‐5 increases the crystallization temperature and decreases the spherulite sizes of both PP‐A and PP‐B, and reduces their crystallization energy barriers as well; however, the polymorphic behaviors of PP‐A and PP‐B exhibit different dependence on the TMB‐5 concentration. For PP‐A with less uniform distribution of stereo‐defects, β‐phase can be observed only when the TMB‐5 concentration is no less than 0.1 wt.%, while for PP‐B with more uniform stereo‐defect distribution, addition of 0.01 wt.% TMB‐5 can induce the formation of β‐phase. Moreover, the analysis of POM indicated that the crystalline morphologies of both PP‐A and PP‐B change greatly with the TMB‐5 concentration, and the variation features of PP‐A and PP‐B are quite different from each other. PP‐B with more uniform stereo‐defect distribution was more favorable for the formation of large amount of β‐phase in the presence of wide concentration range of TMB‐5. The different polymorphic behaviors and their different dependences on the β‐NA concentration were related to the different uniformities of stereo‐defect distribution of the samples, since the distribution of stereo‐defects could restrain the regular insertion of molecular chains during crystallization and thus determine the tendency the α‐phase crystallization of the sample. Copyright © 2014 John Wiley & Sons, Ltd.     

Specificity and versatility of nucleating agents toward isotactic polypropylene crystal phases

Nucleating agents with an ≈6.5 Å lattice parameter induced the α phase of isotactic polypropylene (iPP, α‐iPP). A 6.5 Å periodicity is also involved in the nucleating agents for the β phase of iPP (β‐iPP). The similarity in substrate periodicities suggests that some nucleating agents may induce either the α or β phase under different crystallization conditions. 4‐Fluorobenzoic acid, dicyclohexylterephthalamide, and γ‐quinacridone (the latter two are known as β‐iPP nucleators) were tested over a wide range of crystallization temperatures [up to crystallization temperature (T_c) > 145 °C]. The two former nucleating agents induce exclusively α‐iPP and β‐iPP, respectively. γ‐Quinacridone on the contrary is a versatile agent with respect to the crystal phase generated. More specifically, the same crystal face of γ‐quinacridone induces either β‐iPP or α‐iPP when T_c is below or above ≈140 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2504–2515, 2002     

Crystallization and melting behaviors of isotactic polypropylene nucleated with compound nucleating agents

Crystallization and melting behaviors of isotactic polypropylene (iPP) nucleated with compound nucleating agents of sodium 2,2′‐methylene‐bis (4,6‐di‐tert‐butylphenyl) phosphate (hereinafter called as NA40)/dicyclohexylterephthalamide (hereinafter called as NABW) (weight ratio of NA40 to NABW is 1:1) were studied by differential scanning calorimetry and wide‐angle X‐ray diffraction (WAXD), the relative β‐amount of iPP nucleated with these compound nucleating agents was also calculated in Turner‐Jones equation by using wide‐angle X‐ray diffraction data. Under isothermal crystallization, there exists a temperature range favorable for formation of β‐iPP. When the concentration of compound nucleating agents is 0.2 wt %, the temperature range is from 100 to 140 °C. While in nonisothermal crystallization, lower cooling rate is favorable for form of β‐iPP and the relative β‐amount of iPP increases with the decreasing of cooling rate in crystallization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 911–916, 2008     

Molecular weight dependency of crystallization and melting behavior of β‐nucleated isotactic polypropylene

Compounds of isotactic polypropylene (iPP) and β‐nucleating agent were used to investigate the relationship between the development of β phase and molecular weight in iPP under quiescent crystallization conditions by using wide angle X‐ray diffraction and differential scanning calorimetry techniques. In all cases, the dependency of the formation of β phase in iPP on molecular weight of iPP at a defined crystallization temperature range was found. The iPP with high molecular weight possessed a wide range of crystallization temperature in inducing rich β phase. However, poor or even no β phase was obtained for the samples with low molecular weight in the same range. In addition, an upper critical crystallization temperature of producing dominant β phase was found at 125 °C. Beyond this temperature, a phenomenon of prevailing α phase became obvious. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1301–1308     

Isothermal crystallization behaviors of isotactic polypropylene nucleated with α/β compounding nucleating agents

Sodium 2,2′‐methylene‐bis(4,6‐di‐tert‐butylphenyl) phosphate (NA40) and N,N‐dicyclohexylterephthalamide (NABW) are high effective nucleating agents for inducing the formation of α‐isotactic polypropylene (α‐iPP) and β‐iPP, respectively. The isothermal crystallization kinetics of iPP nucleated with nucleating agents NABW, NA40/NABW (weight ratio of NA40 to NABW is 1:1) and NA40 were investigated by differential scanning calorimetry (DSC) and Avrami equation was adopted to analyze the experimental data. The results show that the addition of NABW, NA40/NABW and NA40 can shorten crystallization half‐time (t_1/2) and increase crystallization rate of iPP greatly. In these three nucleating agents, the α nucleating agent NA40 can shorten t_1/2 of iPP by the largest extent, which indicates that it has the best nucleation effect. While iPP nucleated with NA40/NABW compounding nucleating agents has shorter t_1/2 than iPP nucleated with NABW. The Avrami exponents of iPP and nucleated iPP are close to 3.0, which indicates that the addition of nucleating agents doesn't change the crystallization growth patterns of iPP under isothermal conditions and the crystal growth is heterogeneous three‐dimensional spherulitic growth. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 590–596, 2007     

Nonisothermal crystallization behaviors of polypropylene with α/β nucleating agents

In this work, the nonisothermal crystallization and subsequent melting behaviors of polypropylene (PP) nucleated with different nucleating agents (NAs) have been studied. α‐phase NA 1,3:2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988), β‐phase NA aryl amides compound (TMB‐5), and their compounds were introduced into PP matrix, respectively. The results show that the nonisothermal crystallization behaviors and crystalline structures of PP with compounded NAs are dependent on the composition of NAs. In the sample of PP with 0.1 wt % DMDBS and 0.1 wt % TMB‐5, the nucleation efficiency (NE) of TMB‐5 is much higher than that of DMDBS and PP crystallizes mainly nucleated by TMB‐5, and in this condition, β‐phase PP is the main crystallization structure. For the sample of PP with 0.2 wt % DMDBS and 0.2 wt % TMB‐5, 0.2 wt % DMDBS has higher NE than 0.2 wt % TMB5, and α‐phase is the main crystalline structure. The cooling rate is proved to be very important in controlling the nonisothermal crystallization behavior and the final crystalline structure of nucleated PP. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1853–1867, 2008     

Study of the assembled morphology of aryl amide derivative and its influence on the nonisothermal crystallizations of isotactic polypropylene

The nonisothermal crystallization behaviors of isotactic polypropylene (iPP) with an aryl amide derivative TMB‐5 as β‐form nucleating agent has been investigated by differential scanning calorimetry, X‐ray diffraction, and polarized optical microscopy. The feature of crystallite morphology depends on concentration and thermal conditions. At low concentrations, TMB‐5 molecules aggregate into fibril structures and presented blunt exothermic peak with a shoulder at high temperature. The surface of these fibrils host active sites tailored for the nucleation of β‐iPP, represented by clusters of microcrystallites. With increasing concentration, αβ‐transcrystalline layer develops on the lateral surface of needle‐shaped TMB‐5. Enhanced multiple endotherms indicate the ensuing crystals are less perfect and easily transformed into more stable forms. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 314–325, 2009     

Isothermal crystallization kinetics of polypropylene latex–based nanocomposites with organo‐modified clay

The effect of organo‐modified clay (Cloisite 93A) on the crystal structure and isothermal crystallization behavior of isotactic polypropylene (iPP) in iPP/clay nanocomposites prepared by latex technology was investigated by wide angle X‐ray diffraction, differential scanning calorimetry and polarized optical microscopy. The X‐ray diffraction results indicated that the higher clay loading promotes the formation of the β‐phase crystallites, as evidenced by the appearance of a new peak corresponding to the (300) reflection of β‐iPP. Analysis of the isothermal crystallization showed that the PP nanocomposite (1% C93A) exhibited higher crystallization rates than the neat PP. The unfilled iPP matrix and nanocomposites clearly shows double melting behavior; the shape of the melting transition progressively changes toward single melting with increasing crystallization temperature. The fold surface free energy (σ_e) of polymer chains in the nanocomposites was lower than that in the PP latex (PPL). It should be reasonable to treat C93A as a good nucleating agent for the crystallization of PPL, which plays a determinant effect on the reduction in σ_e during the isothermal crystallization of the nanocomposites. The activation energy, ΔE_a, decreased with the incorporation of clay nanoparticles into the matrix, which in turn indicates that the nucleation process is facilitated by the presence of clay. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1927–1938, 2010     

Effects of β‐nucleating agent and crystallization conditions on the crystallization behavior and polymorphic composition of isotactic polypropylene/multi‐walled carbon nanotubes composites

In this study, the effects of crystallization conditions (cooling rate and end temperature of cooling) on crystallization behavior and polymorphic composition of isotactic polypropylene/multi‐walled carbon nanotubes (iPP/MWCNTs) composites nucleated with different concentrations of β‐nucleating agent (tradename TMB‐5) were investigated by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and scanning electronic microscopy (SEM). The results of DSC, WAXD and SEM revealed that the addition of MWCNTs and TMB‐5 evidently elevates crystallization temperatures and significantly decreases the crystal sizes of iPP. Because of the competition between α‐nucleation (provided by MWCNTs) and β‐nucleation (induced by TMB‐5), the β‐phase crystallization takes place only when 0.15 wt% and higher concentration of TMB‐5 is added. Non‐isothermal crystallization kinetics study showed that the crystallization activation energy ΔE of β‐nucleated iPP/MWCNTs composites is obviously higher than that of pure iPP, which slightly increases with the increase of TMB‐5 concentration, accompanying with the transition of its polymorphic crystallization behavior. The results of non‐isothermal crystallization and melting behavior suggested that the cooling rate and end temperature of cooling (T_end) are important factors in determining the proportion and thermal stability of β‐phase: Lower cooling rate favors the formation of less amount of β‐phase with higher thermal stability, while higher cooling rate encourages the formation of higher proportion of β‐phase with lower thermal stability. The T_end = 100°C can eliminate the β–α recrystallization during the subsequent heating and therefore enhance the thermal stability of the β‐phase. By properly selecting TMB‐5 concentration, cooling rate and T_end, high β‐phase proportion of 88.9% of the sample was obtained. Copyright © 2014 John Wiley & Sons, Ltd.     

Study on the β to α transformation of polypropylene crystals in compatibilized blend of polypropylene/polyamide‐6

By using a commercial β‐nucleating agent (TMB‐5) for polypropylene (PP), it was observed that high β‐crystal content in a compatibilized blend of polypropylene/polyamide‐6 (labeled as Blend‐03 in this work) can be achieved for samples prepared by compression moulding. As β‐PP possesses more superior impact strength then α‐PP, and the β to α transformation is an important mechanism of energy absorption for β‐PP, it is of obvious interest to understand the possibilities of β to α transformation in β‐polypropylene/polyamide‐6 blends. Tensile tests were performed at temperatures of 20, 30, 40, and 50 °C, and the occurrence of β to α transformation was monitored by differential scanning calorimeter and wide angle X‐ray diffraction measurements. It was observed that the β to α transformation in Blend‐03 could only be activated at elevated tensile testing temperatures. This was related to the increase in tensile elongation at break with the increase in tensile testing temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2674–2681, 2007     

Dependence of mechanical properties on β‐form content and crystalline morphology for β‐nucleated isotactic polypropylene

As part of a continuous effort to develop high performance isotactic polypropylene (iPP) based on β‐form crystalline and morphological change induced by rare earth nucleator (WBG), various WBG contents (from 0.025 to 1.0 wt%) were adopted to prepare β‐nucleated iPP at a fixed final molten temperature (240°C) in this study. The crystallinity, polymorphic composition, and crystalline morphology were inspected in detail by a series of crystallographic characterizations, including calorimeter, X‐ray diffraction, polarized light microscopy (PLM), and electron microscopy. Furthermore, the self‐organization and re‐crystallization behavior of β‐nucleating agent occurred during cooling was characterized by rheometry. Finally, the dependence of mechanical properties, including tensile strength, elongation at break, and impact strength, on WBG content was discussed based on the variations in β‐form content and crystalline morphology. Interestingly, it is found that while the WBG content is below 0.1 wt%, the toughness of β‐nucleated iPP increases with increase in WBG content due to additional β‐form content; as the WBG content is in range of 0.1–0.5 wt%, the toughness increases at a lower rate with increase in WBG content due to β‐crystalline morphological change. However, a decrease in toughness is observed while nucleator content is above 0.5 wt% as WBG remains undissolved in iPP upon the adopted processing conditions. The result of this study provides valuable information for potential industrial applications. Copyright © 2010 John Wiley & Sons, Ltd.     

Annealing induced microstructure and fracture resistance changes in isotactic polypropylene/ethylene‐octene copolymer blends with and without β‐phase nucleating agent

Previous work showed that annealing induced the great improvement of fracture resistance of β‐iPP, relating to the decreased number of chain segments in the amorphous region. To further prove the rationality of this observation, in this work, the ethylene‐octene copolymer (POE) toughened isotactic polypropylene (iPP) blends with or without β‐phase nucleating agent (β‐NA) were adopted and the changes of microstructure and fracture resistance during the annealing process were further investigated comparatively. The results showed that, whether for the α‐phase crystalline structure (non‐nucleated) or for the β‐phase crystalline structure (β‐NA nucleated) in iPP matrix, annealing can induce the dramatic improvement of fracture resistance at a certain annealing temperature (120–140 °C for β‐NA nucleated blends whereas 120–150 °C for non‐nucleated blends). Especially, non‐nucleated blends exhibit more apparent variations in fracture resistance compared with β‐NA nucleated blends during the annealing process. The phase morphology of elastomer, supermolecular structure of matrix, the crystalline structure including the degree of crystallinity and the relative content of β‐phase, and the relaxation of chain segments were investigated to explore the toughening mechanism of the samples after being annealed. It was proposed that, even if the content of elastomer is very few, the excellent fracture resistance can be easily achieved through adjusting the numbers of chain segments in the amorphous phase by annealing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Investigation on the dynamic crystallization and melting behavior of β‐nucleated isotactic polypropylene with different stereo‐defect distribution—the role of dual‐selective β‐nucleation agent

The selectivities of different β‐nucleating agents might be quite different from each other, which is important in determining the crystallization and properties of the obtained β‐isotactic polypropylene (β‐iPP). However, the relationship between molecular structure and dynamic crystallization behavior of β‐iPP nucleated by dual‐selective β‐nucleating agent (DS‐β‐NA) is still not clear. In this study, the dynamic crystallization and melting behavior of two β‐iPP with nearly same average isotacticity but different stereo‐defect distribution, nucleated by a DS‐β‐NA (N,N′‐dicyclohexyl‐2,6‐naphthalenedicarboxamide; trade name TMB‐5), were studied by differential scanning calorimetry, wide‐angle X‐ray diffraction, and scanning electronic microscopy. The results indicated that in the presence of TMB‐5, the dynamic crystallization and melting behavior of the samples are quite different because the joint effects of the dual selectivity of TMB‐5 and stereo‐defect distribution of the iPP under different cooling rates. Two important roles were observed: (i) slow cooling rate favors the formation of high β‐fraction; and (ii) high crystallization temperature favors the crystallization of α‐phase accelerated by TMB‐5. Generally, the dual selectivity of the DS‐β‐NA, the stereo‐defect distribution of iPP, and the cooling rate were important factors in determining the formation of β‐crystal. Copyright © 2013 John Wiley & Sons, Ltd.     

Nucleation characteristics of the α/β compounded nucleating agents and their influences on crystallization behavior and mechanical properties of isotactic polypropylene

Nucleation characteristics of isotactic polypropylene (iPP) nucleated by the α/β compounded nucleating agents (NAs) were investigated by wide‐angle X‐ray scattering, differential scanning calorimetry and mechanical testing. The results showed that the nucleation effect of the α/β compounded NAs depends on not only nucleation efficiency (NE) of individual β and α NAs and their ratios but also the processing conditions, especially the cooling rates. The nucleating characteristics of the α/β compounded NAs can be illustrated by competitive nucleation. The NA with high NE played a leading role during iPP crystallization even at a low weight ratio and at different cooling rates. The stiffness and toughness of iPP can be simultaneously improved by using suitable compositions at the appropriate ratios. Finally, the nonisothermal crystallization kinetics of iPP nucleated with the α/β compounded NAs was described by Caze method and the crystallization activation energy of nucleated iPP was calculated by Kissinger equation. The result indicated that the crystal growth pattern of nucleated iPP was heterogeneous nucleation followed by three‐dimension spherical growth. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 653–665, 2010     

Crystallization and melting behavior of isotactic polypropylene nucleated with individual and compound nucleating agents

In this study, α-phase nucleating agent (NA) 1,3:2,4-bis(3,4-dimethylbenzylidene) sorbitol (DMDBS), β-phase rare earth NA (WBG), and their compound NAs were introduced into isotactic polypropylene (iPP) matrix, respectively. Crystallization kinetics and subsequent melting behavior of the nucleated iPPs were comparatively studied by differential scanning calorimetry (DSC) under both isothermal and nonisothermal conditions. For the isothermal crystallization process, it is found that the Avrami model successfully described the crystallization kinetics. The active energy of nonisothermal crystallization of iPP was determined by the Kissinger method and showed that the addition of nucleating agents increased the activation energy. Melting behavior and crystalline structure of the nucleated iPPs are dependent on the nature of NAs and crystallization conditions. Higher proportion of β-phase can be obtained at higher content of β-nucleating agent and lower crystallization temperature or lower cooling rate.     

Crystallization behavior of polypropylene with or without sodium benzoate as a nucleating agent

The crystallization kinetics of polypropylene (PP) with or without sodium benzoate as a nucleating agent were investigated by means of DSC and polarized optical microscopy in isothermal and nonisothermal modes. A modified Avrami equation was applied to the kinetic analysis of isothermal crystallization. The addition of the nucleating agent up to its saturation concentration increased the crystallization temperature by 15 °C and shortened both the isothermal and nonisothermal crystallization half‐times. It was concluded that the sodium benzoate acted as a good nucleating agent for α‐form PP. By adding the nuclefier to PP, adequately controlled spherulites increased the mechanical properties including especially the Izod impact strength and shortened cycle time of PP. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1001–1016, 2001     

Effect of nucleating agent on the brittle–ductile transition behavior of polypropylene/ethylene–octene copolymer blends

In the present work, α‐form nucleating agent 1,3:2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988) is introduced into the blends of polypropylene/ethylene–octene copolymer (PP/POE) blends to study the effect of the nucleating agent on the toughness of PP/POE blends through affecting the crystallization behavior of PP matrix. Compared with the PP/POE blends, in which the toughness of the blends increases gradually with the increasing content of POE and only a weak transition in toughness is observed, addition of 0.2 wt % DMDBS induces not only the definitely brittle‐ductile transition at low POE content but also the enhancement of toughness and tensile strength of the blends simultaneously. Study on the morphologies of impact‐fractured surfaces suggests that the addition of a few amounts of DMDBS increases the degree of plastic deformation of sample during the fracture process. WAXD results suggest that POE induces the formation of the β‐form crystalline of PP; however, DMDBS prevents the formation of it. SEM results show that the addition of DMDBS does not affect the dispersion and phase morphologies of POE particles in PP matrix. DSC and POM results show that, although POE acts as a nucleating agent for PP crystallization and which enhances the crystallization temperature of PP and decreases the spherulites size of PP slightly, DMDBS induces the enhancement of the crystallization temperature of PP and the decrease of spherulites size of PP more greatly. It is concluded that the definitely brittle–ductile transition behavior during the impact process and the great improvement of toughness of the blends are attributed to the sharp decrease of PP spherulites size and their homogeneous distribution obtained by the addition of nucleating agent. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 577–588, 2008     

Probing into the epitaxial crystallization of β form isotactic polypropylene: From experimental observations to molecular mechanics computation

Compared with the most stable crystalline form of isotactic polypropylene (α‐iPP), β‐iPP shows superior impact strength and high temperature performance, though the mechanism of how the frustrated structure of β‐iPP is formed still remains unclear. In present work, the single crystal structure of a traditional β‐iPP nucleating agent, N,N′‐dicyclohexylterephthalamide (DCHT), was obtained for the first time and correlated with the epitaxial crystallization of β‐iPP on the surface of DCHT crystal. The combination of synchrotron radiation X‐ray microdiffraction and molecular chain packing model confirmed that a two dimensional match of chain‐axis and inter‐chain direction coexists between β‐iPP (110) plane and DCHT (001) plane. It was further found that an epitaxial model is helpful to understand the formation of the frustrated structure of 3₁ helices packing in β‐iPP. The molecular mechanics computation showed that as the (001) plane of DCHT is fixed, the packing mode of β‐iPP (110) plane on the substrate surface is more stable than that of α‐iPP (010) plane. This work clarifies the epitaxial crystallization mechanism of β‐iPP on DCHT by employing both experimental and computational evidences. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 418–424     

Influence of additives on the crystal structure and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate)

The influence of additives on the crystal modification and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) was investigated with wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). The addition of a nucleating promoter, Ceraflour 993, had no effect on the crystal modification and melting behavior of PEN crystallized under all chosen experimental conditions. However, the addition of a nucleating agent, sodium benzoate (SB), did affect the crystal modification and melting behavior of PEN when PEN/SB was crystallized at a higher temperature, but not at a lower temperature. A mixture of α and β modifications of PEN was obtained, and an overlapped dual melting peak was observed in DSC curves when PEN was crystallized at a higher temperature in the presence of SB, instead of a single crystal form and a single melting peak for the crystallization of pure PEN. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 296–301, 2004