苯并噻唑和铁氧化物纳米粒子修饰的磁性棒碳糊电极上肼的电催化氧化反应：同时检测肼和苯酚

开发了一种磁性Fe3O4纳米粒子和2-(3,4-二羟苯基)苯并噻唑(DPB)修饰的磁性棒碳糊电极(MBCPE)用于电化学检测肼.首先将DPB自组装在Fe3O4纳米粒子上,然后将此复合物吸附于设计的MBCPE上. MBCPE电极将磁性纳米粒子吸引到电极表面.所得新型电极具有高的导电性和大的有效比表面积,因而对肼的电催化氧化反应有非常大的电流响应.采用伏安法、扫描电镜、电化学阻抗谱、红外光谱和紫外-可见光谱对修饰电极进行了表征.采用伏安法研究了在磷酸盐缓冲溶液(pH=7.0)中MBCPE/Fe3O4NPs/DPB电极上肼的电化学行为.作为电化学传感器, MBCPE/Fe3O4NPs/DPB电极对肼氧化反应表现出极高的电催化活性.在DPB存在下,肼的氧化电势下降,但其催化电流增加.电催化电流与肼浓度在0.1–0.4和0.7–12.0μmol/L二个区间内表现出线性关系,检测限为18.0 nmol/L.另外,研究了MBCPE/Fe3O4NPs/DPB电极同时检测肼和苯酚的性能.伏安实验结果显示,苯酚的线性区域为100–470μmol/L,检测限为24.3μmol/L.采用此电极检测了水样品中的肼和苯酚.     

三维电极电化学反应器对有机废水的降解研究

本文提出一种基于三维电极电化学反应器处理有机废水的新技术 ,结果表明 :该反应器能有效地去除苯胺 ,但其去除率受外加电压、溶液中Fe2 +的浓度、pH值及处理时间 (t)的影响较大 .该项技术处理有机废水效果明显 ,主要是基于电致过氧化氢 ,在Fe2 +存在情况下迅速生成对有机物有很强氧化作用的羟基自由基 .通过ESR法测出了在该电化学反应器处理废水过程中产生的羟基自由基     

二乙腈基二硫纶在金电极上的自组装及其对抗坏血酸的电化学行为研究

将Na2[Ni(mnt)2](mnt=丁二腈烯二硫醇阴离子)自组装到裸金电极表面,制成mnt-SAM/Au修饰电极,并用电化学方法研究了该修饰电极的电化学性质。实验结果表明,mnt-SAM膜对[Fe(CN)6]3-/[Fe(CN)6]4-有一定的排斥作用,而对[Co(phen)3]2+/[Co(phen)3]3+有一定吸引作用。研究了抗坏血酸(AA)在自组装膜修饰金电极上的电化学氧化行为,考察了溶液pH、扫描速率的影响,结果表明该膜对AA的氧化具有催化作用。在最佳条件下,峰电流与AA的浓度在5.0×10-6~1.3×10-3mol·L-1范围内呈良好的线性关系,相关系数为-0.9987,检测限为1.0×10-6 mol·L-1。     

魔芋多糖固定化肌红蛋白的直接电化学与电催化

用魔芋多糖(KGM)和N,N-二甲基甲酰胺(DMF)的加合物,将肌红蛋白(Mb)固定在玻碳电极(GCE)上,制备了稳定的Mb-KGM-DMF/GCE修饰电极,并研究了Mb在修饰电极上的直接电化学行为和电催化性能。该电极在pH=7.0的磷酸盐缓冲溶液(PBS)中,-0.38 V(E0′)处有一对氧化还原峰,峰电位差ΔEp=70 mV,该峰正是Mb中血红素辅基FeⅢ/FeⅡ电对的氧化还原特征峰。在0.2~9.0 V/s扫速的范围内,氧化还原峰峰电流大小和扫描速率成正比,呈现出表面控制行为。在pH为5.0~12.0的范围内,式电位和pH值呈线性关系,表明电子传递过程伴随着质子转移。同时,Mb-KGM-DMF/GCE修饰电极表现出良好的电催化性能,对氧、H2O2有显著的催化作用。在4.70~75.0μmol/L的范围内,其催化峰电流大小与H2O2的浓度有良好的线性关系,其线性回归方程i=0.127 0.093C,r=0.9989,表观米氏常数为80.8μmol/L。     

电沉积普鲁士蓝/壳聚糖修饰金电极的电化学研究

应用控制电位电解法在金电极上进行了普鲁士蓝(PB)/壳聚糖(CS)修饰膜的电沉积。在pH2、溶液组成为2.5 mmol/L FeCl3 2.5 mmol/L K3[Fe(CN)6] 0.01%CS 0.01 mol/L HCl和0.1 mol/L KCl的溶液中,于0.4 V(vs.SCE)电沉积300 s,获得性能理想的沉积膜。对修饰膜进行了红外和显微表征,结果表明,PB和CS同时沉积在电极上,且膜结构较纯PB沉积膜粗糙,修饰量大,具有更强的空间结构性。研究了PB/CS/金修饰电极(PB/CS/Au/CME)的电化学行为,该电极在中性(pH7.0~8.0)条件下性能比纯PB修饰膜更稳定,具有良好的电化学活性和对H2O2的电催化性能。氧化峰电流与H2O2浓度在1×10-6~5×10-3mol/L范围内呈良好线性关系,为研制基于酶催化反应的电化学生物传感器奠定了良好基础。     

镍纳米线电极的交流阻抗研究

用交流阻抗法研究了一种新型电极－镍纳米线电极在碱性溶液中的电化学行为,给出了相应的等效电路和拟合效果。实验结果表明,外加电位对电极表面化学反应速度和类型有显著影响。在外加电位不高时,Ni（Ⅱ）氧化成Ni(Ⅲ)的电化学过程随着电位的升高而明显加速;当外加电位高于0．40V以后,电极表面同时发生电化学析氧反应。相同条件下,镍纳米线电极的表面电化学反应速度远远高于镍块体电极。     

PAOAA修饰金电极固定过氧化氢酶的电化学研究

设计了一种基于金属离子螯合法固定蛋白质的新方法.首先电化学聚合苯胺(ANI)/邻氨基苯甲酸(OAA)得到在中性溶液中具有导电性的聚(苯胺-邻氨基苯甲酸)(PAOAA)共聚物膜,并对膜进行了SEM、EDS表征.随后膜负载Cu2+,Cu2+作为螯合离子通过配位作用固定过氧化氢酶(Cat).用EDS测量了铜的负载量为0.49%.脉冲伏安法(DPV)研究了Cat在金电极表面的固定过程,显示随着ANI/OAA在电极表面聚合成膜、Cat在修饰电极表面固定,电极在10mmol/LK3Fe(CN)6/K4Fe(CN)6(Fe(CN)63-/4-)溶液中的扫描峰电流由裸电极的121μA依次降到92.6、71.8μA,表明电极表面修饰的PAOAA膜和固定的Cat阻碍了电荷的传递.电化学阻抗法(EIS)对固定过程中电极表面阻抗变化的研究也得到同样结论.用线性扫描伏安法(LSV)研究了固定到电极表面后Cat对H2O2的催化还原活性.最后以计时电流法(CA)作为检测手段,Cat修饰电极作为探针实现了对H2O2的定量检测,同时该电极显示出良好的重建性.     

二茂铁-离子液体修饰碳糊电极的研制

以室温离子液体N-辛基吡啶六氟磷酸盐为粘合剂与二茂铁和石墨粉相混合制备了一种新型二茂铁-离子液体修饰碳糊电极。以该电极为工作电极,采用循环伏安法、计时安培法研究了多巴胺(DA)在该糊电极上的电化学行为。实验结果表明:该电极在pH 5.0的乙酸-乙酸钠缓冲溶液中,外加电压0.8 V条件下,灵敏度最高。电流增量与DA浓度在1.0×10-5～1.0×10-3 mol/L范围内呈良好的线性关系,检出限为5.0×10-6 mol/L(S/N=3)。     

对乙酰氨基酚在石墨烯/壳聚糖复合膜修饰电极上的电化学行为研究

制备了石墨烯-壳聚糖复合物修饰玻碳电极(GO/CS-GCE),考察了对乙酰氨基酚(APAP)在修饰电极上的电化学行为,发现石墨烯-壳聚糖复合物能较好改善玻碳电极对APAP的电化学性能,APAP在修饰电极上的电化学反应过程是受吸附控制的2电子,2质子反应过程;进一步研究发现在pH=9.16的碳酸钠-碳酸氢钠缓冲体系中,对...     

膜电阻对自组装膜修饰电极电化学行为的影响

应用循环伏安和交流阻抗技术研究了 16烷基硫醇自组装膜修饰的金电极在Fe(CN) 63 - /Fe(CN) 64 - 溶液中的电化学行为 .无“针孔”缺陷的自组装膜对溶液与基底间的界面电子转移具有强烈的阻碍作用 ,当过电位较大时 ,In(I/ η)对 η1/2 之间具有良好的线性关系 .通过对Au/SAM /Hg模拟体系的电流———电压曲线进行测定 ,得到了自组装膜膜电阻的特征 .指出由于膜电阻的存在 ,自组装膜修饰电极在Fe(CN) 63 - /Fe(CN) 64 - 溶液中的行为实质上反映了膜自身的电阻特征     

Direct electrochemistry of cytochrome <Emphasis Type="Italic">c</Emphasis> entrapped in agarose hydrogel by protein film voltammetry

Cytochrome c (cyt-c) entrapped in agarose hydrogel was electrostatically bound to the edge plane pyrolytic graphite electrode (EPPGE), and then stable agarose-cyt-c/EPPGE was prepared. Direct electrochemistry between cyt-c and the EPPGE was monitored by protein film voltammetry. The effects of ionic strength, pH and exterior substances on the direct electrochemistry, and electrocatalytic properties of cyt-c were also studied. Results show that the electrochemical behavior of heme Fe(III)/Fe(II) in cyt-c is quasireversible. Its electrochemical performance is the best when the concentration of supporting electrolyte phosphate buffer solution is 0.2 mol/l and pH is 7.0, and greatly inhibited by exterior metal ions. Catalytic reduction of oxygen could also be achieved at the agarose-cyt-c/EPPGE.     

Direct electrochemistry of cytochrome c entrapped in agarose hydrogel in room temperature ionic liquids

Direct electrochemistry of cytochrome c (cyt-c) entrapped in agarose hydrogel on gold electrode (Au), edge plane pyrolytic graphite electrode (EPPGE) and glassy carbon electrode (GC) in two room temperature ionic liquids was investigated. The effects of the addition of N,N-dimethylformamide (DMF) in the agarose-cyt-c film, water concentration in ionic liquids and exterior metal ions on the electrochemical behavior of cyt-c were monitored, and electrocatalytic properties of cyt-c were also done. Results showed that a good quasi-reversible redox behavior of cyt-c could be found after adding DMF in agarose-cyt-c film, and peak shape would not change after continuously scanning for 50 cycles. In addition, a certain amount of water in hydrophilic ionic liquids is necessary to maintain electrochemical activities of cyt-c, electrochemical performance of cyt-c is the best when the water content is 5.2% and 5.8% for 1-butyl-3-methylimidazolium bromide ([Bmim][Br]) and 1-butyl-3-methylimidazolium tetrafluoroborate([Bmim][BF(4)]) respectively. However, electrochemical activities of cyt-c are inhibited by exterior metal ions. Interestingly, cyt-c entrapped in agarose hydrogel on EPPGE and GC could catalyze the electroreduction of trichloroacetic acid (TCA) and tert-butyl hydroperoxide (t-BuOOH) in [Bmim][BF(4)], but could not in [Bmim][Br]. Reasons for above-mentioned differences of electrochemical properties of cyt-c in different ionic liquids were preliminarily discussed.     

Myoglobin/sol-gel film modified electrode: direct electrochemistry and electrochemical catalysis

Direct electrochemical and electrocatalytic behavior of myoglobin (Mb) immobilized on carbon paste electrode (CPE) by a silica sol-gel film derived from tetraethyl orthosilicate was investigated for the first time. Mb/sol-gel film modified electrodes show a pair of well-defined and nearly reversible cyclic voltammetric peaks for the Mb Fe(III)/Fe(II) redox couple at about -0.298 V (vs Ag/AgCl) in a pH 7.0 phosphate buffer solution. The formal potential of the Mb heme Fe(III)/Fe(II) couple shifted linearly with pH with a slope of 52.4 mV/pH, denoting that an electron transfer accompanies single-proton transportation. An FTIR and UV-vis spectroscopy study confirms that the secondary structure of Mb immobilized on an electrode by a sol-gel film still maintains the original arrangement. The immobilized Mb displays the features of a peroxidase and acts in an electrocatalytic manner in the reduction of oxygen, trichloroacetic acid (TCA), and nitrite. In comparison to other electrodes, the chemically modified electrodes used in this study for direct electrochemistry and electrocatalysis of Mb are easy to fabricate and fairly inexpensive. Consequently, the Mb/sol-gel film modified electrode provides a convenient way to perform electrochemical research on this kind of protein. It also has potential use in the fabrication of bioreactors and third-generation biosensors.     

Surface electric field manipulation of the adsorption kinetics and biocatalytic properties of cytochrome c on a 3D macroporous Au electrode

Upon adsorbing on a solid-state substrate, water-soluble proteins are prone to denaturation and deterioration of their functions due to the conformation change. The surface electric field of a conductive substrate is one of the important factors that influence the character of adsorbed proteins. In this work, a 3D macroporous gold electrode has been prepared and served as the working electrode to study the influence of surface electric field on the adsorption kinetics and conformation of the adsorbed cytochrome c (cyt-c) with the help of electrochemical, in situ electrochemical IR spectroscopic, atomic force microscopic, and contact angle measurements. The external electric field creates excess surface charge which can manipulate the adsorption rate of proteins on the substrate by the enhanced electrostatic interactions between the electrode and protein patches by coupling with complementary charges. The amount of immobilized cyt-c with electrochemical activity on the 3D macroporous gold electrode showed a minimum at potential of zero charge (PZC) and it increased with increasing net excess surface charge. Higher electric field could influence the conformation and the corresponding properties such as direct electrochemistry, bioactivity, and surface character of the adsorbed cyt-c molecules. However, high external electric field leads to damage of the protein secondary structure. This study provides fundamentals for the fabrication of biomolecular devices, biosensors, and biofuel cells through electrostatic interactions. Figure Two cases are illustrated for the protein immobilized on electrode surfaces: a retention of protein structure under moderate excess surface charge, b denaturation and conformation change of proteins adsorbed at high excess surface charge, e.g., due to the higher external electric field.     

Heterogeneous Electron Transfer and Oxygen Reduction Reaction at Nanostructured Iron(II) Phthalocyanine and Its MWCNTs Nanocomposites

Electron transfer and oxygen reduction dynamics at nanostructured iron(II) phthalocyanine/multi‐walled carbon nanotubes composite supported on an edge plane pyrolytic graphite electrode (EPPGE‐MWCNT‐nanoFePc) platform have been reported. All the electrodes showed the category 3 diffusional behaviour according to the Davies–Compton theoretical framework. Both MWCNTs and MWCNT‐nanoFePc showed huge current responses compared to the other electrodes, suggesting the redox processes of trapped redox species within the porous layers of MWCNTs. Electron transfer process is much easier at the EPPGE‐MWCNT and EPPGE‐MWCNT‐nanoFePc compared to the other electrodes. The best response for oxygen reduction reaction was at the EPPGE‐MWCNT‐nanoFePc, yielding a 4‐electron process.     

Voltammetric investigation of cytochrome c on gold coated with a self-assembled glutathione monolayer

The direct, reversible electrochemistry of horse-heart cytochrome c (cyt. c) was realized on a self-assembled glutathione (GSH) monolayer modified Au electrode. The voltammetric responses of cyt. c on GSH/Au electrode were found to be affected by pH during the electrode modification, metal ions and surfactants. Using potassium ferricyanide [K4Fe(CN)6] as a probe, these effects on the voltammetric responses of cyt. c were characterized by electrochemical methods. It was found that the pH during the electrode modification, metallic ions and surfactants changed GSH monolayer's charge state and the conformation on the electrode surface, and resulted in the influence on the voltammetric responses of cyt. c. The experimental results provided us information to understand the mechanism of the interfacial electron transfer of electrode-protein, as well as the electron transfer of cyt. c in life system.     

Electropolymerization of iron tetra(<Emphasis Type="Italic">o</Emphasis>-aminophenyl)porphyrin from aqueous solution and the electrocatalytic behavior of modified electrode

Stable electroactive iron tetra(o-aminophenyl)porphyrin (FeTAPP) films are prepared by electropolymerization from aqueous solution by cycling the electrode potential between −0.4 and 1.0 V vs Ag/AgCl at 0.1 V s⁻¹. The cyclic voltammetric response indicates that polymerization takes place after the oxidation of amino groups, and the films could be produced on glassy carbon (GC) and gold electrodes. The film growth of poly(FeTAPP) was monitored by using cyclic voltammetry and electrochemical quartz crystal microbalance. The cyclic voltammetric features of Fe(III)/Fe(II) redox couple in the film resembles that of surface confined redox species. The electrochemical response of the modified electrode was found to be dependent on the pH of the contacting solution with a negative shift of 57 mV/pH. The electrocatalytic behavior of poly(FeTAPP) film-modified electrode was investigated towards reduction of hydrogen peroxide, molecular oxygen, and chloroacetic acids (mono-, di-, and tri-). The reduction of hydrogen peroxide, molecular oxygen, and dichloroacetic acid occurred at less negative potential on poly(FeTAPP) film compared to bare GC electrode. Particularly, the overpotential of hydrogen peroxide was reduced substantially. The O₂ reduction proceeds through direct four-electron reduction mechanism.     

电位调控制备还原氧化石墨烯的电催化性能研究

本文通过控制电位还原氧化石墨烯,可控制备不同含氧官能团的石墨烯纳米材料。以多巴胺、[Fe(CN)_6]~(3-)、NADH为电活性探针,研究了石墨烯表面含氧官能团、缺陷、表面荷电性质以及导电性等对石墨烯电催化性能的影响。研究发现,低还原程度的氧化石墨烯表面含有大量缺陷和丰富的官能团,能够促进多巴胺自催化反应,也有利于K_3[Fe(CN)_6]在电极表面的电子转移;随着氧化石墨烯还原程度提高,其导电性逐渐得到改善,且其表面官能团和缺陷位点数量逐渐减少,对NAD~+的吸附变弱,因而能促进NADH发生电催化氧化。     

Ionic Liquid‐Hemoglobin‐Carbon Paste Composite Bioelectrode and Its Electrocatalytic Activity

A new carbon ionic liquid paste bioelectrode was fabricated by mixing hemoglobin (Hb) with graphite powder, ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) and liquid paraffin homogeneously. Nafion film was cast on the electrode surface to improve the stability of bioelectrode. Direct electrochemistry of Hb in the bioelectrode was carefully investigated. Cyclic voltammetric results indicated that a pair of well‐defined and quasi‐reversible electrochemical responses appeared in pH 7.0 phosphate buffer solution (PBS), indicating that direct electron transfer of Hb was realized in the modified electrode. The formal potential (E^0′) was calculated as ?0.316 V (vs. SCE), which was the typical characteristic of the electrochemical reaction of heme Fe(III)/Fe(II) redox couple. Based on the cyclic voltammetric results the electrochemical parameters of the electrode reaction were calculated. This bioelectrode showed high electrocatalytic activity towards the reduction of trichloroacetic acid (TCA) with good stability and reproducibility.     

Direct electrochemistry and electrocatalysis with horseradish peroxidase in Eastman AQ films

Stable films made from ionomer poly(ester sulfonic acid) or Eastman AQ29 on pyrolytic graphite (PG) electrodes gave direct electrochemistry for incorporated enzyme horseradish peroxidase (HRP). Cyclic voltammetry of HRP-AQ films showed a pair of well-defined, nearly reversible peaks at about -0.33 V vs. SCE at pH 7.0 in blank buffers, characteristic of HRP heme Fe(III)/Fe(II) redox couple. The electron transfer between HRP and PG electrode was greatly facilitated in AQ films. The electrochemical parameters such as apparent heterogeneous electron transfer rate constant (k(s)) and formal potential (E(o')) were estimated by fitting the data of square-wave voltammetry (SWV) with nonlinear regression analysis. Reflectance absorption infrared (RAIR) and UV-Vis absorption spectra demonstrated that HRP retained a near native conformation in AQ films. The embedded HRP in AQ films retained the electrocatalytic activity for oxygen, nitrite and hydrogen peroxide. Possible mechanism of catalytic reduction of H(2)O(2) with HRP-AQ films was proposed.