常温常压湿式催化氧化染料废水的Mo-Cu-Fe-O新型复合催化材料（英文）

染料广泛应用于纺织厂、皮革厂以及染发等各个领域.染料废水具有成分复杂、浓度高、色度大和生物难降解等特性,因此传统的处理方法难以将其完全降解.高级氧化技术已成为国内外广泛应用的染料废水处理技术之一,特别是湿式催化氧化(CWAO)技术.然而,CWAO工艺中反应往往需要高温(通常为200-280°C)和高压(通常为2-9 MPa),制约了其广泛应用.因此,人们致力于研发具有高催化活性的催化剂,通过改变反应历程和降低反应的活化能,使反应在常温常压条件下进行.本课题组曾采用钼酸盐浸渍于Zn/Al LDHs溶液中成功制备了Mo/Zn-Al LDHs催化剂,该催化剂能在常温常压下湿式催化氧化降解阳离子红GTL有机废水.Mo/Zn-Al LDHs催化剂中Mo作为主催化成分,Zn-Al LDHs作为载体.Cu-Fe LDHs本身作为一种催化剂,与Mo相结合能有效提高催化剂的活性及稳定性,因此本文采用浸渍法制备了Mo-Cu-Fe-O新型复合催化材料,采用X射线衍射、氢气程序升温还原、循环伏安法和氧气程序升温脱附等表征手段研究了Mo-Cu-Fe-O材料的结构及氧化还原特性.以阳离子红GTL、结晶紫和酸性红为染料废水代表,研究了常温常压下Mo-Cu-Fe-O催化降解染料废水的催化活性.结果表明,在中性条件下Mo-Cu-Fe-O对阳离子型染料废水具有良好的催化活性.循环使用七次后该样品对阳离子红GTL和酸性红的脱色率分别达到91.5%和92.8%,然而对酸性红阴离子型染料废水基本无催化活性.在常温常压CWAO过程中产生的羟基自由基能有效降解阳离子GTL废水,其废水毒性随着反应的进行逐渐减小.     

改性二氧化钛负载贵金属Ru催化剂催化降解苯胺溶液

苯胺类废水污染物具有结构复杂、浓度高、不易生物降解、生物毒性大等特点,传统的苯胺降解措施存在着许多弊端,很难达到排放标准.催化湿法氧化技术(CWAO)主要针对降解高浓度难降解的有机废水,表现出降解效率高、反应时间短、对生物毒性物质的废水降解效果良好等优点,越来越受到人们的重视.但催化剂在使用过程中,需要在高温高压下进行,且有机物降解产生了有机酸,使得催化剂的活性组分流失和载体的物理化学性质发生变化,导致其催化活性下降.因此,需要开发出一种降解活性高,性能稳定的催化剂成为此技术在工业中广泛应用的关键.本文采用溶胶凝胶法对二氧化钛进行改性,制备了Ti0.9Zr0.1O2和Ti0.9Ce0.1O2载体,采用过量浸渍法将三氯化钌负载到载体表面制备了2%Ru/Ti0.9Zr0.1O2和2%Ru/Ti0.9Ce0.1O2催化剂.在高温高压反应条件下,以苯胺为催化湿法氧化污染物,对不同催化剂湿法降解苯胺进行比较研究,系统地探究了催化降解的反应温度和反应压力对苯胺降解的影响.此外,利用HPLC-MS鉴定出催化降解产生的中间产物,确定了催化降解的反应路径图.在改性的催化剂中,2%Ru/Ti0.9Zr0.1O2催化剂表现出最高的催化降解活性和稳定性.在初始苯胺浓度4 g/L,催化剂浓度4 g/L,反应温度180℃,O2压力1.5 MPa下,反应时间5 h后,苯胺完全转化,COD转化率达88.3%.并且催化剂进行三次循环试验后,苯胺转化率仍接近100%.X射线衍射和N2物理吸附结果表明,Ce,Zr掺杂到TiO2晶格中形成了共溶体,其晶格尺寸更小,比表面积和孔体积更大.负载贵金属后,并未出现其他晶相,说明贵金属均匀分散在载体表面.透射电镜结果表明,贵金属负载在改性TiO2上表现出较好的分散性和较小的颗粒尺寸,为催化降解苯胺提供更多的催化活性位点,而Ru/TiO2催化剂表面,贵金属发生团聚现象且颗粒尺寸大.X射线光电子能谱结果表明,Ce,Zr的掺杂使得TiO2表面活性氧和四价Ru的含量增加,更多的表面活性氧成为催化降解苯胺的直接原因.H2程序升温还原结果表明,在300?400oC处还原峰对应于催化剂载体晶格氧的还原,改性后,其还原峰增至2倍,即使在贫氧环境下,改性催化剂可以及时从载体中释放晶格氧,为催化降解苯胺提供更多的活性氧.     

改性二氧化钛负载贵金属Ru催化剂催化降解苯胺溶液（英文）

苯胺类废水污染物具有结构复杂、浓度高、不易生物降解、生物毒性大等特点,传统的苯胺降解措施存在着许多弊端,很难达到排放标准.催化湿法氧化技术(CWAO)主要针对降解高浓度难降解的有机废水,表现出降解效率高、反应时间短、对生物毒性物质的废水降解效果良好等优点,越来越受到人们的重视.但催化剂在使用过程中,需要在高温高压下进行,且有机物降解产生了有机酸,使得催化剂的活性组分流失和载体的物理化学性质发生变化,导致其催化活性下降.因此,需要开发出一种降解活性高,性能稳定的催化剂成为此技术在工业中广泛应用的关键.本文采用溶胶凝胶法对二氧化钛进行改性,制备了Ti_(0.9)Zr_(0.1)O_2和Ti_(0.9)Ce_(0.1)O_2载体,采用过量浸渍法将三氯化钌负载到载体表面制备了2%Ru/Ti_(0.9)Zr_(0.1)O_2和2%Ru/Ti_(0.9)Ce_(0.1)O_2催化剂.在高温高压反应条件下,以苯胺为催化湿法氧化污染物,对不同催化剂湿法降解苯胺进行比较研究,系统地探究了催化降解的反应温度和反应压力对苯胺降解的影响.此外,利用HPLC-MS鉴定出催化降解产生的中间产物,确定了催化降解的反应路径图.在改性的催化剂中,2%Ru/Ti_(0.9)Zr_(0.1)O_2催化剂表现出最高的催化降解活性和稳定性.在初始苯胺浓度4 g/L,催化剂浓度4 g/L,反应温度180°C,O_2压力1.5 MPa下,反应时间5 h后,苯胺完全转化,COD转化率达88.3%.并且催化剂进行三次循环试验后,苯胺转化率仍接近100%.X射线衍射和N2物理吸附结果表明,Ce,Zr掺杂到TiO_2晶格中形成了共溶体,其晶格尺寸更小,比表面积和孔体积更大.负载贵金属后,并未出现其他晶相,说明贵金属均匀分散在载体表面.透射电镜结果表明,贵金属负载在改性TiO_2上表现出较好的分散性和较小的颗粒尺寸,为催化降解苯胺提供更多的催化活性位点,而Ru/TiO_2催化剂表面,贵金属发生团聚现象且颗粒尺寸大.X射线光电子能谱结果表明,Ce,Zr的掺杂使得TiO_2表面活性氧和四价Ru的含量增加,更多的表面活性氧成为催化降解苯胺的直接原因.H_2程序升温还原结果表明,在300-400oC处还原峰对应于催化剂载体晶格氧的还原,改性后,其还原峰增至2倍,即使在贫氧环境下,改性催化剂可以及时从载体中释放晶格氧,为催化降解苯胺提供更多的活性氧.     

载体效应对Pt催化剂在一甲胺湿式氧化中的催化性能影响研究

采用浸渍法制备了Pt/AC,Pt/ZrO2,Pt/Al2O3催化剂,并研究了其对一甲胺湿式氧化(CWAO)反应的催化性能.结果表明:载体对Pt的催化活性具有十分明显的影响,当Pt负载到活性炭(AC)载体表面时具有最佳的催化活性,其次是氧化锆,而当Pt负载到氧化铝载体表面时,其催化活性最低.一甲胺在Pt/AC,Pt/ZrO2,Pt/Al2O3催化剂表面被矿化所需最低温度分别为200,250和280℃.Pt/AC催化剂优异的催化活性主要归因于Pt与载体间的弱相互作用、活性炭的大比表面积以及载体自身具有一定的催化活性.     

MoVBiTeO/SiO2对丙烷选择氧化制丙烯醛反应的催化性能

用浸渍法制备了一系列不同Mo/V比的MoVBiTeO/SiO2催化剂,并用X射线衍射、拉曼光谱、X射线光电子能谱、程序升温还原和红外光谱等方法对催化剂的结构、氧化还原性质和酸性进行了表征,考察了催化剂对丙烷选择氧化制丙烯醛反应的催化性能.结果表明,Mo与V组分之间存在较强的相互作用,调变了催化剂的结构,并形成了氧化还原循环(V5 Mo5 V4 Mo6 ),促进了催化剂中电子和O物种的传递,使催化剂的低温可还原性增强,催化活性提高.Mo组分有利于形成L酸位,而V组分有利于形成B酸位.这可能是丙烯醛选择性随Mo/V比增大而逐渐提高的原因之一.当Mo/V摩尔比为6时,催化剂具有最高的丙烯醛收率(9.7%).     

石墨烯氢氧化钴复合催化剂的一步合成及其对酸性橙的催化降解(英文)

用一步合成自组装法制备出了氢氧化钴与还原氧化石墨烯(Co(OH)2/rGO)的复合催化剂,并将其用于水中染料的催化降解实验.通过X射线衍射(XRD),激光拉曼(Raman)光谱,透射电镜(TEM),X射线能量色散谱(EDS)以及X射线光电子能谱(XPS)等一系列分析手段对催化剂的结构形貌进行了详细的表征,表征结果证实氢氧化钴很好地附着在还原石墨烯的表面.最后初步考察了催化剂催化单过硫酸钾(PMS)降解酸性橙(AO7)的性能.结果表明,催化剂显示出了高效的催化性能,酸性橙的色度可在12 min内完全去除,总有机碳(TOC)实验也表明染料降解的同时也可获得较高的矿化度.循环稳定性实验表明在进行到第三次实验时,催化剂仍能保持高的催化活性,将酸性橙在16 min内降解完毕.     

以乙酸为模型反应物的Ti-Ce复合氧化物湿式氧化催化剂的研制

催化湿式氧化(catalytic wet air oxidation, CWAO)为高浓度难降解有机废水提供了一种有效可行的处理技术[1～8],它可使难降解有机物分子在相对较低的反应温与压力下降解矿化或生成易生物处理的小分子有机物.     

石墨烯氢氧化钴复合催化剂的一步合成及其对酸性橙的催化降解

用一步合成自组装法制备出了氢氧化钴与还原氧化石墨烯（Co（OH）₂/rGO）的复合催化剂,并将其用于水中染料的催化降解实验. 通过X射线衍射（XRD）,激光拉曼（Raman）光谱,透射电镜（TEM）,X射线能量色散谱（EDS）以及X射线光电子能谱（XPS）等一系列分析手段对催化剂的结构形貌进行了详细的表征,表征结果证实氢氧化钴很好地附着在还原石墨烯的表面. 最后初步考察了催化剂催化单过硫酸钾（PMS）降解酸性橙（AO7）的性能. 结果表明,催化剂显示出了高效的催化性能,酸性橙的色度可在12 min内完全去除,总有机碳（TOC）实验也表明染料降解的同时也可获得较高的矿化度. 循环稳定性实验表明在进行到第三次实验时,催化剂仍能保持高的催化活性,将酸性橙在16 min内降解完毕.     

纳米碳管负载金属镍催化叶绿素加氢反应

用等体积浸渍法制备了纳米碳管负载金属镍催化剂，采用电镜(TEM）、红外光谱（IR）对催化剂的形貌、结构进行了表征.并考察了常温常压下不同Ni负载量的催化剂对叶绿素加氢反应的性能.结果表明，纳米碳管负载镍催化剂在催化反应过程中保持高分散态，不会发生团聚.而经过硝酸氧化后的纳米碳管负载镍催化剂在催化反应中表现出高的活性.当Ni负载量为7％时，催化活性最好，叶绿素分子开环生成各种小分子.     

M/Al2O3-CeO2（M=Pt-Ru，Ru，Pt）催化剂在甲胺催化湿式氧化中的活性与选择性

采用浸渍法制备了M/Al₂O₃-CeO₂（M=Pt-Ru,Ru,Pt）催化剂,并将其用于甲胺的催化湿式氧化反应（CWAO）.结果表明,Pt-Ru/Al₂O₃-CeO₂具有最佳活性和选择性.运用程序升温还原、X射线光电子能谱、X射线衍射、透射电子显微镜、N₂吸附和CO化学吸附等技术对催化剂的物化性质进行了表征.Pt组分的引入可有效提高双金属催化剂活性组分的分散度,从而明显提高了其催化性能.升降温过程中总有机碳（TOC）转化率与N₂选择性迟滞效应表明,甲胺CWAO遵循化学吸附-脱附机理.     

Determination of the degradation products of selected sulfonated phenylazonaphthol dyes treated by white rot fungus Pleurotus ostreatus by capillary electrophoresis coupled with electrospray ionization ion trap mass spectrometry

The removal of water-soluble sulphonated phenylazonaphthol dye effluents generated by textile industries is an important issue in wastewater treatment. Microbial treatment of environmental pollutants including dyes, with white rot fungi has received wide attention as a potential alternative for conventional methods in wastewater treatment. Three sulphonated phenylazonaphthol dyes with similar molecular structures Acid Orange 7, Acid Orange 8 and Mordant Violet 5 were selected and degraded by the white rot fungus Pleurotus ostreatus. Chemical instrumental analysis methods such as high-performance liquid chromatography (HPLC) and capillary electrophoresis combined with electrospray ionization mass spectrometry (CE-ESI-MS) were used to identify the degraded dyes. Mordant Violet 5 had two degradation pathways when degraded by P. ostreatus. The first degradation pathway for Mordant Violet 5 was for trans structure and the cis-Mordant Violet 5 followed the second pathway. Acid Orange 8 and Acid Orange 7 had the same degradation mechanism as the first degradation mechanism for Mordant Violet 5, that is cleavage of azo bond at the naphthalene ring side where benzenesulfonic acid and 1,2-naphthoquinone are formed.     

An investigation into the initial degradation steps of four major dye chromophores: study of their one-electron oxidation and reduction by EPR, ENDOR, cyclic voltammetry, and theoretical calculations

The degradation of dyes is frequently initiated by one-electron oxidation or reduction; however, relatively little is known about the initially formed radicals. Acid Green 25 (AG25), Crystal Violet (CVI), Methylene Blue (MB), and Acid Orange 7 (AO7), representing paradigms of four types of commercial organic dyes, were therefore investigated in terms of their redox behavior. Their redox potentials in MeCN and buffered aqueous solutions were determined by cyclic voltammetry. The structures of the one-electron reduced and oxidized dyes were established by EPR spectroscopy and by theoretical calculations on the density functional level of theory.     

Treatment of direct blending dye wastewater and recycling of dye sludge

A new sorbent material, barium sulfate-Direct Blending Yellow D-3RNL hybrid (BSD), was synthesized and characterized by various methods. Both the anionic dyes, Reactive Brilliant Red X-3B and Weak Acid Green GS were hardly adsorbed by the BSD material, while the sorption of Ethyl Violet (EV) and Victoria Blue B were extremely obvious. The sorption of cationic dyes obeyed the Langmuir isotherm model, which depended on the electric charge attraction. The saturation amount of EV adsorbed onto the BSD material approached to 39.36 mg/g. The sorption of EV changed little with pH from 3 to 12 while it increased with increasing levels of electrolyte. A dye wastewater sampled from Jinjiang Chemicals was treated, and the color removal rate was more than the COD removal rate. In addition, the cationic dye-BSD sludge was utilized as a colorant fill-in coating. The light stability and thermal stability of the colorant was measured and exhibited good features. This work provided a simple and eco-friendly method for dye wastewater treatment with recycling of waste.     

Effect of dye aggregation on triarylmethane-mediated photoinduced damage of hexokinase and DNA

The observation that enhanced mitochondrial membrane potential is a prevalent cancer cell phenotype has provided the conceptual basis for the development of mitochondrial targeting as a novel therapeutic strategy for both chemo- and photochemotherapy of neoplastic diseases. Cationic triarylmethane (TAM(+)) dyes represent a series of photosensitizers whose phototoxic effects develop at least in part at the mitochondrial level. In this report we describe how the molecular structure of four representative TAM(+) dyes (Crystal Violet, Ethyl Violet, Victoria blue R, and Victoria pure blue BO) affects their efficiency as mediators of the photoinduced inactivation of two model mitochondrial targets, hexokinase (HK) and DNA. Our results have indicated that TAM(+) dyes efficiently bind to HK and DNA in aqueous media both as dye monomers and aggregates, with the degree of aggregation increasing with increasing the lipophilic character of the photosensitizer. The efficiency with which HK and DNA are damaged upon 532 nm photolysis of biopolymer-TAM(+) complexes was found to decrease upon increasing the degree of dye aggregation over these macromolecular templates. Comparative experiments carried out both in water and in D(2)O, and in air-equilibrated and nitrogen-purged samples have also indicated that, at least when Crystal Violet is used as the photosensitizer, the mechanism of macromolecular damage does not require the involvement of molecular oxygen to operate. This finding makes Crystal Violet a potential candidate for use in photochemotherapy of hypoxic or poorly perfused tumor areas.     

Study of the influential factors in the simultaneous photocatalytic degradation process of three textile dyes

The influence of several factors in the simultaneous photocatalytic degradation of three textile dyes - Acid Red 97, Acid Orange 61 and Acid Brown 425 - has been studied using a fractional factorial design 2^5-1. The considered factors were: the initial concentration of each dye, the catalyst concentration (TiO₂) and pH.First, we developed a rapid analytical methodology based on recording UV-visible spectra during the degradation process and a data treatment using multivariate curve resolution with alternating least squares (MCR-ALS), which enabled the three dyes to be quantified simultaneously despite the overlap of their spectra.The kinetic constant of degradation for each dye in all the experiments was evaluated. In all cases the degradation followed a first order kinetics. For a significance level of 5%, the most important factor in the photodegradation of each dye is the concentration of Acid Red 97, the degradation is more effective at higher pHs and, in the studied range, the concentration of the catalyst is not important.     

Minireview: Silver-Doped Titanium Dioxide and Silver-Doped Zinc Oxide Photocatalysts

The catalytic oxidation of organic dyes using various systems has been widely reported during the past decade. Photocatalytic methods, heterogeneous processes for the degradation of dyes, are one of the best and efficient oxidation processes to treat industrial wastewater with minimal residual waste. This review describes the improvement in catalytic activity of silver-doped titanium dioxide and silver-doped zinc oxide. The degradation of dyes provides information about the catalytic performance of silver-doped metal oxide. The effects of pH, catalyst concentration, dye concentration, hydrogen peroxide, dissolved oxygen, temperature, irradiation time, and light source have been reviewed along with the degradation mechanism and reaction methodology of organic dyes.     

Inverse voltammetry of antimony with triphenylmethane dyes

A method is suggested for the determination of traces of antimony by inverse voltammetry of the solid phases formed with triphenylmethane dyes (Crystal Violet, Methyl Violet and Malachite Green) as the precipitants. The authors have studied the effect of concentration, adsorption and oxidation of the triphenylmethane dyes, potential and time of pre-electrolysis, and concentration of antimony(III) and some other elements on the polarogram shape and stripping current. A method for determining antimony traces in chromic salts is described as an example.     

Enhancement of azo dyes removal efficiency by using LDH/Tris/Pd catalyst: Kinetic studies

LDH/Tris/Pd (CaAl‐layered double hydroxide/tris (hydroxymethyl)aminomethane/palladium) was synthesized and appraised for its catalytic activity towards the degradation of two selected azo dyes. The decolorization of azo dyes, acid red 18 (AR 18) and reactive yellow 15 (RY 15), requires considerably small amounts of synthesized catalyst. Kinetic studies show that the catalytic decolorization of these azo dyes follows the first order kinetic model. The reported method is simple and applicable; in addition, the stable catalyst can efficiently decolorize model azo dyes with good recyclability. Therefore, LDH/Tris/Pd can be accepted as the possible component for the utilization in wastewater treatment.     

Ultrasound-assisted nanoscaled supramolecular coordination polymer as an efficient recyclable catalyst for photocatalytic degradation of dye pollutants

An ultrasound-assisted nanoscaled supramolecular coordination polymer (nanosized 1′ ) has been synthesized using a self-assembly reaction of K₃[Cu (CN)₄] and hexamethylenetetramine in the presence of Me₃SnCl under ambient conditions. Nanosized 1′ was examined using elemental analysis, Fourier transform–infrared, transmission electron microscopy, scanning electron microscopy and X-ray powder diffractions. It was structurally compared with the single crystal supramolecular coordination polymer ^∞₃[Cu₆(CN)₇(C₆H₁₂N₄)₂(OH₃)]; SCP 1. The photocatalytic activities of nanosized 1′ and SCP 1 toward different hazardous organic dyes were determined under ambient, UV-light irradiation and ultrasonic conditions. SCP 1 and nanosized 1′ as heterogeneous nanoparticles catalysts exhibited high catalytic activity for degradation of Congo Red, Methyl Violet 2B and Methylene Blue dyes. The effects of operational parameters on catalytic degradation process, identification of the degradation products and recycling of the catalyst were also investigated. SCP 1 and nanosized 1′ are recyclable heterogeneous catalysts and can be reused with efficient activities. The mechanism of degradation using different scavenger techniques iss proposed and discussed. The catalytic oxidation process is mainly caused by ^•OH radicals.     

改性PAN纤维与铁离子的配位结构及其对染料降解的催化作用

在室温条件下应用偕胺肟改性聚丙烯腈纤维(AO-PAN)与FeCl3反应制备了聚丙烯腈纤维铁配合物(Fe-AO-PAN), 并分别使用X射线光电子能谱(XPS)、傅立叶红外光谱(FTIR)、动态热机械分析(DTMA)和电导法对Fe-AO-PAN进行了表征以确定其组成结构. 然后将Fe-AO-PAN作为非均相Fenton 催化剂应用于两种常用偶氮染料C.I.活性红195(RR 195)和C.I.酸性黑234(AB 234)的光催化氧化降解反应中, 考察了其对降解反应的催化作用. 结果表明, Fe-AO-PAN中的Fe3+能够与AO-PAN表面三个偕胺肟(AO)链节单元的三个氨基氮原子和三个羟基氧原子进行配位反应, 配位数为6. 在Fe-AO-PAN和辐射光存在下, 两种染料的氧化降解反应速度显著加快, 染料结构中的偶氮键和芳香环结构都遭到破坏. PAN纤维腈基转化率的提高不仅能够明显增加Fe-AOPAN表面结构中Fe3+含量, 而且可显著促进其对染料氧化降解反应的催化作用.