1,2-亚乙基氧化硅螺旋纳米管在制备过程中的手性反转

以D-缬氨酸为手性源合成了手性阴离子两亲性小分子化合物D-C12ValC10COONa. 用圆二色谱表征了该化合物在溶液和胶体中的自组装行为. 通过溶胶\|凝胶复制法, 以该手性化合物和结构助剂3-(三甲氧基硅基)丙胺的组装体为模板, 制备了左手螺旋1,2-亚乙基氧化硅纳米管. 扫描电镜和透射电子显微镜研究显示, 调节溶液浓度和pH值可以控制1,2-亚乙基氧化硅纳米管的手性, 而温度和溶剂配比的改变对纳米管手性并无影响.     

二元阴、 阳离子表面活性剂调控合成不同形貌的介孔二氧化硅

经过简单的水热处理, 以二元阴、 阳离子表面活性剂[十六烷基三甲基溴化铵(CTAB)和十二烷基磺酸钠(SDS)分别作为阳离子表面活性剂和阴离子表面活性剂]为模板剂合成了不同形貌的介孔二氧化硅. 通过调控2种表面活性剂摩尔分数R(R=n(SDS)/[n(SDS)+n(CTAB)]), 合成了多种形貌的介孔二氧化硅. 对合成的不同形貌样品通过扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 X射线粉末衍射仪(XRD) 及比表面和孔隙分析仪进行了表征. 结果表明, 随着R值从0.01变化到0.50, 介孔二氧化硅的形貌经历了一系列规律性的变化, 出现了二维六方、 层状相和反相堆积的形貌: 在R=0.01~0.18之间, 主要产物为六方相棒状结构, 且长径比随着R值增大而增大; 在R=0.20~0.28之间主要得到空心泡状结构且具有明显的演变过程; 在R=0.32~0.40之间发生了多层囊泡到单层囊泡的结构转变; 当R值超过一定范围时会产生反相堆积的形貌. 分析认为, SDS在加入过程中通过影响堆积参数g影响胶束的形貌变化, 调控了不同形貌介孔二氧化硅的合成. 各阶段产物形貌和R值的变化有直接关系, 可通过改变R值来合成特定形貌的产物.     

Synthesis of hollow spherical silica with MCM-41 mesoporous structure

Hollow spherical mesoporous silica was synthesized by using sodium silicate as a precursor and a low concentration of cetyltrimethylammonium bromide (CTAB) (0.154 mol dm^–3). The resulting hollow spherical particles were characterized with scanning electron microcopy (SEM), small-angle X-ray diffraction (SXRD), transmission electron microscopy (TEM), and N₂ gas adsorption and desorption techniques. The results showed that regular spherical mesoporous silica could be obtained only if the molar ratio of propanol to CTAB was in the range of approximately 8:1–9:1. The spherical particles were hollow (inside), and the shell consisted of smaller particles with a pore structure of hexagonal symmetry. With an increase of the molar ratio of propanol to CTAB, the distance (a value) between centers of two adjacent pores increased, and the pore structure of mesoporous silica became less ordered. N₂ adsorption–desorption curves revealed type IV isotherms and H1 hysteresis loops; with an increase of the molar ratio of propanol to CTAB, the pore size with Barrett–Joyner–Halenda (BJH) diameter of the most probable distribution decreased, but the half peak width of the pore size distribution peak increased     

Preparation of Helical Mesoporous Ethenylene-silica Nanofibers with Lamellar Mesopores on Their Surface

The morphologies and pore architectures of mesoporous ethenylene‐silica were controlled using cetyltrimethylammonium bromide (CTAB) as template and (S)‐β‐citronellol as a co‐structure‐directing agent under basic conditions. When the (S)‐β‐citronellol/CTAB molar ratios are in the range of 0.75–2.0, helical nanofibers were obtained. With increasing the (S)‐β‐citronellol/CTAB molar ratio, the lengths of the nanofibers increases. Lamellar mesopores were identified on the surfaces of the nanofibers prepared in the (S)‐β‐citronellol/CTAB molar ratio range of 1.5–2.0. At the (S)‐β‐citronellol/CTAB molar ratio of 2.5:1, nanoparticles with nanoflakes on the surfaces were obtained. The field emission scanning electron microscopy images taken after different reaction times indicated that the helical pitches of the nanofibers decreased with increasing the reaction time. Helical 1,4‐phenylene‐silica and methylene‐silica nanofibers were also prepared. The results indicated that the morphologies and pore architectures of the obtained organic‐inorganic hybrid silicas are also sensitive to the hybrid silica precursors. Helical ethenylene‐silica nanofibers with lamellar mesopores on their surfaces can be also prepared using the mixtures of CTAB and racemic citronellol within a narrower citronellol/CTAB molar ratio range.     

Preparation and characterization of mesoporous silica thin films from polyethoxysiloxanes

Tetraethoxysilane (TEOS) and polyethoxysiloxanes (PEOSs; prepared by the acid‐catalyzed hydrolytic polycondensation of TEOS) were subjected to the sol–gel process in the presence of cetyltrimethylammonium bromide (CTAB), respectively. The PEOSs with M_w 700–26,000, as prepared by sol–gel coating of TEOS and PEOS under various conditions, were used. Uniform and crack‐free thin films of thickness 276–613 nm were prepared by spin‐coating of a PEOS solution containing CTAB. When the coating films were sintered at 400 °C, the combustion of ethoxy groups and CTAB took place to provide porous silica thin films. The structure of the thin films was found to be dependent on the molecular weight of PEOS and the molar ratio of CTAB/Si: lamellar or hexagonal phase was observed for M_w less than 15,000 and for CTAB/Si molar ratios greater than 0.10. Honeycomb structures were observed for M_w less than 5000 and for CTAB/Si molar ratios of 0.15. The honeycomb structure was also observed by atomic force microscopy and transmission electron microscope. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2542–2550, 2006     

以卵磷脂为手性添加剂制备手性介孔二氧化硅

以十六烷基三甲基溴化铵(CTAB)的自组装体为模板,卵磷脂(PC)为手性添加剂,在n_PC:n_CTAB=1:21时,通过溶胶-凝胶法制备了螺旋介孔二氧化硅纳米棒。利用扫描电镜(FESEM)、透射电镜(TEM)、X-射线衍射以及氮气吸附-脱附等测试手段,对该纳米棒的形貌以及孔结构进行了表征。TEM显示该纳米棒的长度约为50~200nm,直径约为30~50nm。X-射线衍射表明孔道呈二维六方排列,虽然FESEM显示纳米棒左右手比例约为1:1,但通过圆二色谱表征证明该纳米棒在埃尺度下倾向于形成单一手性。结果表明,卵磷脂的手性可以传递到螺旋介孔二氧化硅纳米棒中。     

以卵磷脂为手性添加剂制备手性介孔二氧化硅

以十六烷基三甲基溴化铵(CTAB)的自组装体为模板,卵磷脂(PC)为手性添加剂,在n PC∶nCTAB=1∶21时,通过溶胶-凝胶法制备了螺旋介孔二氧化硅纳米棒。利用扫描电镜(FESEM)、透射电镜(TEM)、X-射线衍射以及氮气吸附-脱附等测试手段,对该纳米棒的形貌以及孔结构进行了表征。TEM显示该纳米棒的长度约为50～200 nm,直径约为30～50 nm。X-射线衍射表明孔道呈二维六方排列,虽然FESEM显示纳米棒左右手比例约为1∶1,但通过圆二色谱表征证明该纳米棒在埃尺度下倾向于形成单一手性。结果表明,卵磷脂的手性可以传递到螺旋介孔二氧化硅纳米棒中。     

Mechanism of crystallization of CaCO3 in system H2O-CaCl2-Na2CO3-1,2-Bis(4-aminophenoxy)ethane-N,N,N′,N′-tetraacetic acid-cetyltrimethylammonium bromide

The growth characteristics of calcium carbonate (CaCO₃) in the mixed systems of 1,2-bis(4-aminophenoxy)ethane-N,N,N′,N′-tetraacetic acid (BAPTA) and cetyltrimethyl ammonium bromide (CTAB) were studied in our experiments. The as-prepared products were characterized by scanning electron micro-scope and X-ray diffraction. Calcite and vaterite with various morphologies were contained in the BAPTA single system and the mixed systems with CTAB/BAPTA molar ratio of 1: 2 and 1: 1.25, while only calcite produced in the mixed systems with CTAB/BAPTA molar ratio of 1: 5, 1: 1, 1: 0.67 and pure CTAB system. The possible formation mechanisms of CaCO₃ produced in different solutions were discussed in the end.     

Synthesis of rod-like mesoporous silica with hexagonal appearance using sodium silicate as precursor

Using sodium silicate as precursor, rod-like mesoporous silica with hexagonal appearance was synthesized by controlling the pH value of a mixed micelles solution of cetyltrimethylammonium bromide (CTAB) and cetyltrimethylammonium chloride (CTAC) during hydrolysis of ethyl acetate. The resulting mesoporous silica was characterized by small angle X-ray diffraction, nitrogen gas adsorption-desorption measurement and scanning electron microscopy. Results showed that the regular rod-like shapes with hexagonal appearance were obtained at a 9:1 molar ratio of CTAB to CTAC, and that the amounts and lengths of the rod-like mesoporous silica particles decreased with decreasing CTAB to CTAC molar ratio. There existed a type IV adsorption isotherm and an H1 hysteresis loop in N₂ gas adsorption-desorption curves.     

Microemulsion-mediated solvothermal synthesis of SrCO3 nanostructures

The controlled synthesis of SrCO3 nanostructures with different morphologies, such as rodlike, whiskerlike, ellipsoidlike, and spherelike, were successfully achieved by the cationic surfactant-CTAB-microemulsion-mediated solvothermal method. Various comparison experiments showed that fundamental experimental parameters, such as the molar ratio of H2O to CTAB and the concentration of reactants, played important roles in the morphological control of SrCO3 nanostructures. A lower molar ratio of H2O to CTAB favors rodlike products, whereas a higher molar ratio generally leads to the formation of spherical products. A rational mechanism based on fusion, aggregate, and coalescence of microemulsion droplets is proposed for the selective formation of various morphologies. X-ray powder diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and field-emission scanning electron microscope (FE-SEM) were used to characterize the products.     

微乳辅助的溶剂热法合成磷酸钐纳米棒

自1991年碳纳米管被发现以来,一维纳米材料以其独特的电、磁、光学和机械性质以及在纳米器件和功能材料上的巨大应用潜力而引起全世界的广泛关注,人们通过模板法、溶胶-凝胶法、水热法及微乳液法等多种方法合成了一系列一维纳米材料,其中微乳液法是近几年来兴起的较有发展前景的纳米材料的合成方法,微乳液是由油相、水相、表面活性剂和助表面活性剂组成的均匀稳定的体系,水相在表面活性剂和助表面活性剂的作用下均匀地分散在油相中,     

双模板法制备介孔二氧化硅纳米蚕茧

用十八烷基三甲基溴化铵(STAB)作模板剂,左旋香茅醇(CN)为结构助剂,利用溶胶-凝胶法,在CN/STAB摩尔比1∶1条件下制备了介孔二氧化硅纳米蚕茧;采用扫描电镜和透射电镜分析了产物的结构,并对其进行了氮气吸附-脱附测试.结果表明,所制备的介孔二氧化硅纳米蚕茧的孔道与蚕茧表面平行;搅拌速度对介孔二氧化硅纳米蚕茧的长度有较大的影响,随着搅拌速度的增加,其长度减小.     

CTAB assisted hydrothermal synthesis, controlled conversion and CO oxidation properties of CeO2 nanoplates, nanotubes, and nanorods

In this work, CeO₂ nanoplates were synthesized by a hydrothermal reaction assisted by hexadecyltrimethylammonium bromide (CTAB) at 100-160 °C. The size of nanoplates was around 40 nm. Further experiment showed that the controlled conversion of nanoplates into nanotubes, and nanorods can be realized by changing the reaction time, temperature, and CTAB/Ce³⁺ ratio value. X-ray diffraction (XRD), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) nitrogen adsorption-desorption measurements were employed to characterize the samples. The CO oxidation properties of nanorods, nanoplates, and nanotubes were investigated. An enhanced catalytic activity has been found for CO oxidation by using CeO₂ nanoplates as compared with CeO₂ nanotubes and nanorods, and the crystal surfaces (100) of CeO₂ nanoplates were considered to play an important role in determining their catalytic oxidation properties.     

Preparation and characterization of helical carbon/silica nanofibers with lamellar mesopores on the surfaces

Helical 1,2-ethylene-silica nanofibers with lamellar mesopores on the surfaces and twisted rod-like mesopores inside were prepared according to literature procedures. After carbonization, helical carbon/ silica nanofibers with lamellar mesopores on the surfaces and twisted rod-like micropores inside were obtained. The morphologies and pore architectures of the carbon]silica nanofibers were characterized using transmission electron microscopy, field-emission scanning electron microscopy, powder X-ray diffraction and N2 sorptions. Although the mesopores inside shrank into micropores, the helical nanostructure remained. Moreover, several carbon/silica nanofibers with lamellar mesopores on the surfaces and concentric circular micropores inside were also obtained. After being calcined in air, helical silica nanofibers with lamellar mesopores on the surfaces and twisted rod-like micropores inside were produced as well.     

水热合成Co3O4的制备参数调变及其催化分解N2O性能

以十六烷基三甲基溴化胺（CTAB）为模板剂,通过调变CTAB浓度水热合成了氧化钴前驱体,焙烧制得棒状形貌的Co₃O₄,在其表面浸渍K₂CO₃溶液制得K改性的Co₃O₄催化剂,用于N₂O分解。用X射线衍射（XRD）、N₂物理吸附（BET）、扫描电镜（SEM）、X射线光电子能谱（XPS）、H₂程序升温还原（H₂-TPR）和O₂程序升温脱附（O₂-TPD）等技术对催化剂进行了表征,考察了CTAB/钴及尿素/钴物质的量比等制备参数对Co₃O₄催化分解N₂O活性的影响。结果表明,CTAB浓度为0.05 mol/L、CTAB/钴离子物质的量比为1、尿素/钴离子物质的量比为4时,所制备的Co₃O₄催化剂具有较高的N₂O分解活性,而K改性可以进一步提升其催化性能。K改性的Co₃O₄在有氧有水气氛中400℃下进行N₂O分解反应,50 h后N₂O转化率仍保持在91%以上。     

CTAB作用下纳米复合材料Ag/ZnO-SnO2的制备与光催化降解罗丹明B

在模板剂溴化十六烷基三甲基胺(CTAB)作用下,采用溶胶-凝胶法再结合程序升温溶剂热法制备了纳米复合材料Ag/ZnO-SnO2(CTAB),其中Ag,Zn,Sn摩尔比为0.1∶2∶1.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、扫描电子显微镜配合X射线能量色散谱(SEM-EDS)和N2吸附-脱附测定等方法对复合材料的组成、结构及形貌等进行了表征.结果表明,该复合材料具有纤锌矿和金红石结构,Ag以单质形式存在.与未经CTAB作用的样品相比,Ag/ZnO-SnO2(CTAB)颗粒分布更均匀,且呈现规则的纳米棒状结构.复合材料在紫外光和可见光作用下对罗丹明B(RhB)的光催化降解结果显示,样品Ag/ZnO-SnO2(CTAB)的光催化活性明显高于Ag/ZnO-SnO2、ZnO-SnO2、ZnO和商用P-25.     

一步法合成多级孔结构ZSM-5分子筛

多级孔结构ZSM-5分子筛的合成过程复杂。利用双模板剂,通过优化晶化条件(如晶化时间与晶化温度)和Si/Al物质的量比等一步水热晶化合成了具有多级孔结构的ZSM-5分子筛,并采用XRD、N₂吸附-脱附、吡啶红外吸脱附、SEM和TEM等方法对样品的晶体结构、孔道结构、表面酸性和形貌等进行了表征。结果表明,一步法合成多级孔结构ZSM-5分子筛的适宜条件是:晶化温度160-180℃,晶化时间24-96 h,反应物组成为SiO₂/Al₂O₃/Na₂O/CTAB/TPABr/H₂O=1/x/0.4/0.05/0.12/280,(x:50-240)。其中,晶化温度160℃、晶化时间48 h和以Si/Al物质的量比50的凝胶合成的样品具有有序的介孔(平均尺寸3.60 nm)结构、较高的结晶度和较强的酸性。     

Preparation of Mesoporous 1,4‐Phenylene‐silica Nanorings through a Dual‐templating Approach

Mesoporous 1,4‐phenylene‐silica nanorings were prepared using cetyltrimethylammonium bromide (CTAB) and (S)‐2‐methyl‐1‐butanol as a chiral dopant in concentrated aqueous NH₃ solutions. Transmission electron microscopy images of the samples indicated that the nanorings were formed by bending nanorods 360°. With increasing the stirring speed or the (S)‐2‐methyl‐1‐butanol/CTAB molar ratio, the morphologies of mesoporous 1,4‐phenylene‐silicas changed from helical nanofibers to nanorings, and then to nano‐saddles. Circular dichroism spectra of these hybrid silicas indicated that they were chiral.     

Multicyclic polyethers by the polycondensation of 1,2‐ or 1,3‐dicyanotetrafluorobenzene with flexible diphenols

1,2‐Dicyanotetrafluorobenzene (1,2‐DCTB) was polycondensed with various flexible diphenols in a molar ratio of 1:2, and experimental parameters such as the concentration and temperature were varied. Certain diphenols allowed a complete substitution of all C? F bonds, so perfect multicyclic polyethers (B_nCN, where B stands for bridge units, C represents cycles, and N is the degree of polymerization) were the main reaction products. Despite complete conversion, gelation was avoidable under optimized reaction conditions. However, in the case of 1,3‐dicyanotetrafluorobenzene (1,3‐DCTB), complete tetrasubstitution was not feasible with a feed ratio of 1:2. Yet, because of the inductive and mesomeric electronic interactions of all substituents in 1,3‐DCTB, the three C? F groups in the ortho position with respect to the cyano groups were significantly more reactive than the fourth C? F bond. Therefore, polycondensations with diphenols in a 3:2 feed ratio showed a relatively clean course, yielding soluble multicycles of structure B_{n /2}CN. All the multicyclic polyethers were amorphous and possessed molar mass distributions with polydispersities greater than 2. Heating with Cu²⁺ salts caused crosslinking of the multicycles derived from 1,2‐DCTB because of the formation of phthalocyanine complexes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5546–5556, 2006     

反相微乳液法制备膜状普鲁士蓝类配合物纳米材料

在十六烷基三甲基溴化铵(CTAB)/正戊醇/异辛烷/水构成的油包水型(W/O)微乳体系中合成了膜状及50 nm立方状的Co-Fe普鲁士蓝类配合物(cobalt-iron Prussian blue analogues). 研究了w值(水与CTAB的物质的量的比)、反应物浓度和反应温度对产品形貌的影响. 并用原子力显微镜(AFM), 透射电子显微镜(TEM), 电子能谱(EDS), X射线光电子能谱(XPS)和红外(IR)对产品进行了表征.