掠射椭偏术对K_4〔Fe(CN)_6〕/K_3〔Fe(CN)_6〕电极反应的研究

提出掠射椭圆偏振测试技术的实验方案,应用该掠射式技术结合循环伏安法研究了在镀有Ｉｎ２Ｏ３玻璃片上进行的Ｋ４〔Ｆｅ（ＣＮ）６〕／Ｋ３〔Ｆｅ（ＣＮ）６〕电极反应．结果证明：掠射椭圆偏振术可在电化学反应过程中现场测定椭圆偏振参数及其变化规律,这些规律与所发生的表面电化学反应规律相对应,由此可以对电极体系进行研究;现场掠射椭圆偏振术还能用于分析表面扩散层的性质,弥补其它界面研究方法的缺陷．     

光导纤维光谱电化学池的研制及初步应用

研制了光导纤维光谱电化学池(FOSECC),并用该池研究Fe(CN)₆^3-/Fe(CN)₆^4-一氧化还原体系。获得不同电位下的吸收光谱;在不同温度下分别测定了式量电位E°′和反应得失电子数n;求出了体系电极反应的△H°和△S°;计算了FOSECC的灵敏度--摩尔吸收/电位比,结果满意。     

NaxMyFe（CN）6（M=Fe,Co,Ni）:一类新颖的钠离子电池正极材料

应用化学沉淀法合成了3种普鲁士蓝类化合物NaxMyFe(CN)6(M=Fe,Co,Ni),并研究了以此类化合物作钠离子电池正极材料的可行性.XRD和SEM分析表明,合成的3种目标产物均具有典型的立方晶型结构,粒子尺寸为20～50 nm.循环伏安扫描和恒电流充放电测试表明,这类化合物均能实现可逆的钠离子嵌入-脱嵌反应,但不同的金属表现出不同的电化学性质.如M为Fe或Co,材料中的Fe(CN)64+和Fe2+/Co2+离子这两个电化学活性中心都能参与氧化还原反应,NaFeFe(CN)6和Na2CoFe(CN)6的首周可逆容量分别为113和120mAh.g-1,且循环性能比较稳定.由于这类结构中Ni离子不能参与氧化还原反应,Na2NiFe(CN)6的可逆容量仅为64 mAh.g-1,但循环性能非常优异.本工作的初步结果证明了普鲁士蓝类化合物具有良好的钠离子脱嵌能力,有望成为一类价格低廉、环境友好的钠离子电池正极材料.     

基于环蕃类分子的铁氰化钾电化学存储和释放

通过利用合成的环蕃类化合物1与单壁碳纳米管(SWNTs)间的π-π共轭相互作用,将化合物1固定在SWNTs的表面,制备了1-SWNT修饰电极.利用化合物1氧化态和还原态与铁氰化钾分子之间不同强度的主客体相互作用,实现了铁氰化钾分子在1-SWNT修饰电极表面的电化学可控吸附和解吸.循环伏安和XPS实验结果表明,在本研究采用的实验条件下,铁氰化钾分子在电极表面20s内即可达到吸附平衡;当电极在0.70V下极化1000s后,大多数吸附的铁氰化钾可从电极表面解吸.基于此,制备了铁氰化钾的可控存储和释放的电化学器件,该器件不但可以重复进行铁氰化钾分子的存储和释放,而且多次重复操作表现出较好的稳定性和重现性.本研究在发展具有特殊用途的电化学纳米器件,例如分子搬运器、电化学开关等研究中具有重要意义.     

Determination of Electrochemical Electron‐Transfer Reaction Standard Rate Constants at Nanoelectrodes: Standard Rate Constants for Ferrocenylmethyltrimethylammonium(III)/(II) and Hexacyanoferrate(III)/(II)

The most common approximation of electroneutrality is inappropriate for analyzing the voltammetric response of nanoelectrodes. Therefore, the microelectrode theory for extracting the standard rate constant k⁰ for electron transfer from steady‐state voltammograms is invalid for nanoelectrodes. Unlike previous approaches, we considered the influence of the interfacial potential distribution caused by the absence of electroneutrality. We estimated the magnitude of the error at low overpotential incurred as a result of ignoring the absence of electroneutrality and found that it was small. In this region, electrochemical reaction appears to be limited by the rate of electron transfer. Under these conditions, k⁰ can be obtained from steady‐state voltammogram data in a low overpotential region according to an approximate form of the Butler–Volmer equation. This procedure can greatly simplify analysis and calculation of the rate constant k⁰ at nanoelectrodes. Steady‐state voltammogram of equal‐concentration hexacyanoferrate(III)/(II) (Fe(CN) /Fe(CN) ) and ferrocenylmethyltrimethylammonium(III)/(II) (FcTMA²⁺/FcTMA⁺) redox couples were investigated at Pt? Ir nanoelectrodes in the presence of a support electrolyte. k⁰ for Fe(CN) /Fe(CN) and FcTMA²⁺/FcTMA⁺ at Pt? Ir nanoelectrodes were evaluated.     

碱性电解液中K3[Fe(CN)6]在锌阳极上的自发还原和吸附延长锌镍电池的循环寿命

In view of the continuously worsening environmental problems, fossil fuels will not be able to support the development of human life in the future. Hence, it is of great importance to work on the efficient utilization of cleaner energy resources. In this case, cheap, reliable, and eco-friendly grid-scale energy storage systems can play a key role in optimizing our energy usage. When compared with lithium-ion and lead-acid batteries, the excellent safety, environmental benignity, and low toxicity of aqueous Zn-based batteries make them competitive in the context of large-scale energy storage. Among the various Zn-based batteries, due to a high open-circuit voltage and excellent rate performance, Zn-Ni batteries have great potential in practical applications. Nevertheless, the intrinsic obstacles associated with the use of Zn anodes in alkaline electrolytes, such as dendrite, shape change, passivation, and corrosion, limit their commercial application. Hence, we have focused our current efforts on inhibiting the corrosion and dissolution of Zn species. Based on a previous study from our research group, the failure of the Zn-Ni battery was caused by the shape change of the Zn anode, which stemmed from the dissolution of Zn and uneven current distribution on the anode. Therefore, for the current study, we selected K₃[Fe(CN)₆] as an electrolyte additive that would help minimize the corrosion and dissolution of the Zn anode. In the alkaline electrolyte, [Fe(CN)₆]^3– was reduced to [Fe(CN)₆]^4– by the metallic Zn present in the Zn-Ni battery. Owing to its low solubility in the electrolyte, K₄[Fe(CN)₆] adhered to the active Zn anode, thereby inhibiting the aggregation and corrosion of Zn. Ultimately, the shape change of the anode was effectively eliminated, which improved the cycling life of the Zn-Ni battery by more than three times (i.e., from 124 cycles to more than 423 cycles). As for capacity retention, the Zn-Ni battery with the pristine electrolyte only exhibited 40% capacity retention after 85 cycles, while the Zn-Ni battery with the modified electrolyte (i.e., containing K₃[Fe(CN)₆]) showed 72% capacity retention. Moreover, unlike conventional organic additives that increase electrode polarization, the addition of K₃[Fe(CN)₆] not only significantly reduced the charge-transfer resistance in a simplified three-electrode system, but also improved the discharge capacity and rate performance of the Zn-Ni battery. Importantly, considering that this strategy was easy to achieve and minimized additional costs, K₃[Fe(CN)₆], as an electrolyte additive with almost no negative effect, has tremendous potential in commercial Zn-Ni batteries.     

碱性电解液中K3[Fe(CN)6]在锌阳极上的自发还原和吸附延长锌镍电池的循环寿命

采用K₃[Fe(CN)₆]作为锌镍电池的电解液添加剂,克服了锌阳极的变形。此外,通过一系列实验设计和表征,探索了电解液中金属锌与K₃[Fe(CN)₆]的反应机理。通过XRD (X-ray diffraction)和XPS (X-ray photo-electron spectroscopy)测试,我们发现金属锌在KOH水溶液中能够与K₃[Fe(CN)₆]反应,将[Fe(CN)₆]^3–还原为[Fe(CN)₆]⁴⁻。添加K₃[Fe(CN)₆]的锌镍电池实现了更长的循环寿命,比不添加K₃[Fe(CN)₆]的锌镍电池长3倍以上。在相同循环次数下,改性电解质中锌阳极循环不仅形状变化较小,而且没有出现“死”锌现象,电极添加剂和粘结剂也没有发生偏析。此外,不同于一般的有机添加剂,K₃[Fe(CN)₆]的加入不仅不会增大电极的极化,还能够提高锌镍电池的放电容量和倍率性能。因此,考虑到这一改性策略有着较高的可行性和较低的成本,K₃[Fe(CN)₆]添加剂在锌镍电池的实际应用中具有极大的推广潜力。     

A novel dual-impedance-analysis EQCM system--investigation of bovine serum albumin adsorption on gold and platinum electrode surfaces

Both quartz crystal micro-balance (QCM) impedance and electrochemical impedance spectroscopy (EIS) methods are widely used in interface studies. This paper presents details about a new strategy for simultaneous, mutual-interference-free and accurate measurements of QCM impedance and EI, through connecting a suitable capacitance in series with the piezoelectric quartz crystal (PQC) between QCM impedance and EIS measurement instruments. Combined and individual measurements of QCM impedance and EIS during silver deposition gave results comparable with each other, demonstrating the reliability of the proposed method. Bovine serum albumin (BSA) adsorption on gold and platinum electrodes in Britton-Robinson (B-R) buffers was investigated, and the Fe(CN)6(3-)/Fe(CN)6(4-) couple was used as an electrochemical probe to characterize BSA adsorption. While the reversibility of Fe(CN)6(3-)/Fe(CN)6(4-) couple on bare Au and Pt electrodes changed very slightly with decreasing solution pH from pH approximately 7 to pH approximately 2, the standard rate constant (ks) of this couple increased abruptly with solution pH below pH approximately 4.5 at a BSA-modified Au electrode, but decreased with solution pH at a BSA-modified Pt electrode. By analyzing the QCM impedance data with a modified BVD equivalent circuit and the EI data with a modified Randle's equivalent circuit, inflexion changes at pH approximately 4.5 were all found at pH-dependent responses of the resonant frequency, the double-layer capacitance, the capacitance of the adsorbed BSA layer, the peak-absorbance values of BSA solutions at 277.5 and 224.5 nm, and so on. It was also found that a BSA adsorption layer can effectively inhibit gold corrosion during ferrocyanide oxidation in a ferrocyanide-containing BR solution. Some preliminary explanations of these findings have been given. The proposed method is highly recommended for wider applications in surface science.     

Mossbauer study of reactions of Sn[Fe(CN)_6] on supports

Mossbauer spectroscopy has been applied to the investigation of reaction of Sn[Fe(CN)6] on magnesia, 7-alumina, silica and activated carbon. It was found that the thermal decomposition products of supported Sn[Fe(CN)6] are quite different from those of the unsupported one as a result of the interaction between the complex and supports. The supports could promote the oxidation in the air atmosphere and their effect led to high dispersion of the decomposition products on the surface.     

Lithium Ferrocyanide Catholyte for High-Energy and Low-cost Aqueous Redox Flow Batteries**

Aqueous redox flow batteries (ARFBs) are a promising technology for grid-scale energy storage, however, their commercial success relies on redox-active materials (RAM) with high electron storage capacity and cost competitiveness. Herein, a redox-active material lithium ferrocyanide (Li₄[Fe(CN)₆]) is designed. Li⁺ ions not only greatly boost the solubility of [Fe(CN)₆]⁴⁻ to 2.32 M at room temperature due to weak intermolecular interactions, but also improves the electrochemical performance of [Fe(CN)₆]^4−/3−. By coupling with Zn, ZIRFBs were built, and the capacity of the batteries was as high as 61.64 Ah L⁻¹ (pH-neutral) and 56.28 Ah L⁻¹ (alkaline) at a [Fe(CN)₆]⁴⁻ concentration of 2.30 M and 2.10 M. These represent unprecedentedly high [Fe(CN)₆]⁴⁻ concentrations and battery energy densities reported to date. Moreover, benefiting from the low cost of Li₄[Fe(CN)₆], the overall chemical cost of alkaline ZIRFB is as low as $11 per kWh, which is one-twentieth that of the state-of-the-art VFB ($211.54 per kWh). This work breaks through the limitations of traditional electrolyte composition optimization and will strongly promote the development of economical [Fe(CN)₆]^4−/3−-based RFBs in the future.     

Electrochemical Behavior of K3[Fe(CN)6] on the Electrode Coated with Modified Multi‐Walled Carbon Nanotubes

The electrochemical behavior of K₃[Fe(CN)₆] was studied on an ITO electrode that was coated with β‐cyclodextrin (CD) modified multi‐walled carbon nanotubes (MWNTs) and with carboxyl modified multi‐walled carbon nanotubes (MWNT‐COOHs). MWNT‐COOHs showed an excellent electrocatalytic effect on the redox of K₃[Fe(CN)₆] while MWNT‐CDs had a subdued effect on the electrochemical response of K₃[Fe(CN)₆]. It is probably due to mismatching between K₃[Fe(CN)₆] and cyclodextrin, which hampers the contact of K₃[Fe(CN)₆] with carbon nanotubes. Moreover, the electrochemical behavior of K₃[Fe(CN)₆] on the MWNT‐COOHs coated ITO electrode at various scan rates also was measured. The results indicated that both potential difference between redox peaks and peak current of K₃[Fe(CN)₆] increased with increasing scan rate. A good linearity of peak current versus scan rate was observed.     

Electrochemical behavior of Ru(H_2bpp)_2(PF_6)_2 and its interaction with bovine serum albumin(BSA)

In this paper,it was found that Ru（H₂bpp）₂（PF₆）2（H₂bpp = 2,6-bis（pyrazol-3-yl）pyridine） complex had excellent electrochemical activity at the carbon paste electrode in the buffer solution of Tris-HCl（pH 7.0） with a couple reversible redox peaks at 0.296 V and 0.348 V,respectively.Voltammetry was used to investigate the electrochemical behavior of Ru（H₂bpp）₂（PF₆）₂ and the interaction between Ru（H₂bpp）₂（PF₆）₂ and bovine serum albumin（BSA）.In the present of BSA,the oxidation peak current of Ru（H₂bpp）₂（PF₆）₂ complex was decreased linearly and the decrease of oxidation peak current of Ru（H₂bpp）₂（PF₆）₂ is proportional to BSA concentration from 0.1 to 2.5 mg/L with a detection limit 0.02 mg/L.     

基于铁氰化钾电子媒介体及醛基吡啶盐的电化学免疫传感器

采用聚二烯丙基二甲基氯化铵(PDDA)将铁氰化钾电子媒介体固定在电极表面,构建免标记的电化学免疫传感器. 醛基吡啶盐不仅作为基底物质直接固定抗体,还可以很好地增强电极表面的导电性能. 将构建的传感器用于肿瘤标志物甲胎蛋白的检测. 其线性范围为0.01-20 ng·mL^-1,检测下限为0.004 ng·mL^-1（3 S/N）. 此传感器的构建简单方便、无标记、特异性好,为甲胎蛋白及其他肿瘤标志物提供了新的检测方法.     

电化学石英晶体阻抗系统研究金电极上Fe(CN)_6~(3-)/Fe(CN)_6~(4-)电化学过程

电化学过程的石英晶体阻抗分析法已用于现场获取电活性聚合物粘弹性等信息［１,２］．本文联用ＨＰ４３９５Ａ阻抗／网络／频谱分析仪和ＥＧ＆ＧＭ２８３恒电位仪开发出电化学石英晶体阻抗系统（ＥｌｅｃｔｒｏｃｈｅｍｉｃａｌＱｕａｒｔｚＣｒｙｓｔａｌＩｍｐｅｄａｎ...     

Resonance Rayleigh scattering, second-order scattering and frequency doubling scattering methods for the indirect determination of penicillin antibiotics based on the formation of Fe3[Fe(CN)6]2 nanoparticles

Under the HCl solution and heating condition, penicillin antibiotics such as amoxicillin (AMO), ampicillin (AMP), sodium cloxacillin (CLO), sodium carbenicillin (CAR) and sodium benzylpenicillin (BEN) could react with Fe(III) to produce Fe(II) which further reacted with Fe(CN)₆³⁻ to form a Fe₃[Fe(CN)₆]₂ complex. By virtue of hydrophobic force and Van der Waals force, the complex aggregated to form Fe₃[Fe(CN)₆]₂ nanoparticles with an average diameter of 45 nm. This resulted in a significant enhancement of resonance Rayleigh scattering (RRS) and non-linear scattering such as second-order scattering (SOS) and frequency doubling scattering (FDS). The increments of scattering intensity (ΔI) were directly proportional to the concentrations of the antibiotics in a certain range. The detection limits for the five penicillin antibiotics were 2.9–6.1 ng ml⁻¹ for RRS method, 4.0–6.8 ng ml⁻¹ for SOS method and 7.4–16.2 ng ml⁻¹ for FDS method, respectively. Among them, the RRS method exhibited the highest sensitivity and the AMO system was more sensitive than other antibiotics systems. Based on the above researches, a new highly sensitive and simple method for the indirect determination of penicillin antibiotics has been developed. It can be applied to the determination of penicillin antibiotics in capsule, tablet, human serum and urine samples. In this work, the spectral characteristics of absorption, RRS, SOS and FDS spectra, the optimum conditions of the reaction and the influencing factors were investigated. In addition, the reaction mechanism was discussed.     

Fe(ClO_4)_3氧化合成聚乙撑二氧-三噻吩

分别以Fe(Cl O4)3、FeCl3、Fe2(SO4)3作为氧化剂,对3′,4′-乙撑二氧-2,2′∶5′,2″-三噻吩(TET)进行了化学氧化聚合,并研究了聚合条件对聚合物结构和电化学性能的影响。利用红外光谱、紫外光谱、X射线衍射对聚合物进行了表征,采用循环伏安、恒电流充放电等电化学方法研究了聚合物的电化学性能。结果表明:当TET与Fe(Cl O4)3的摩尔比为1∶4,反应温度为18℃,反应时间为12 h时,聚3′,4′-乙撑二氧-2,2′∶5′,2″-三噻吩(PTET)具有更好的共轭结构和电化学性能,导电率可达1.47 S/m,比电容可达133 F/g。     

Interaction of Photoactive[Fe（CN）6]4^- with TiO2 Anatase（101） Surface： A Periodic Density Functional Theory Study

The plane-wave pseudopotential function method,based on density-functional theory,has been used to calculate the adsorption,electronic band structures,orbitals and optical absorption spectrum of [Fe(CN)6]4-on TiO2 anatase(101) surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe(CN)6]4-adsorption on the (101) surface could lead to a large red shift of the anatase optical absorption threshold,which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development of photovoltaic materials that are active under visible light.     

二茂铁衍生物L—B膜修饰SnO2电极的性能

用外层单电子快速转移的氧化还原剂二茂铁及其衍生物修饰电极,在电极/溶液界面作为电子传递的中介物,可使电极上进行的慢反应得到加速、起中介催化作用。目前研究较多的是共价键合和高分子膜的修饰,其他方式的修饰报道不多。用能实现分子有序化排列的L-B膜技术进行氧化还原电活性分子的修饰电极还未见报道。我们用L-B膜技术在SnO_2电极上修饰了二茂铁的衍生物-硬脂酸二茂铁酯(FcOCOC_(17)H_(35))双亲化合物,曾研究了修饰膜的电化学可逆行为和稳定性。本文研究硬脂酸二茂铁酯L-B膜修饰的SnO_2电极     

Micellar effects on photoinduced redox reactions of Fe(bpy)2(CN)2

Excitation of solutions of Fe(bipy)₂(CN)₂ by a 266-nm laser pulse produces a hydrated electron and the oxidized complex, Fe(bipy)₂ (CN)₂⁺, in the primary photochemical step, in homogeneous aqueous solution as well as in aqueous solutions containing cetyltrimethylammonium bromide (CTAB) or sodium dodecyl sulfate (SDS) micelles. In all cases nascent hydrated electrons react with ground state Fe(bipy)₂(CN)₂ to form Fe(bipy)₂(CN)₂⁻, and comparison of the decay constants in the three media (H₂O: k = 2.8 × 10¹⁰ M⁻¹ s⁻¹; CTAB: k = 2.9 × 10¹⁰ M⁻¹ s⁻¹; SDS: k = 5.5 × 10⁹ M⁻¹ s⁻¹), shows that the reaction is essentially unaffected by CTAB micelles but is much slower in SDS solution. Similar micellar effects were found for the back reaction between e_aq⁻ and Fe(bpy)₂(CN)₂⁺. Rate constants for the scavenging of the photogenerated hydrated electrons by methyl viologen (MV²⁺) cations and NO₃⁻ anions were measured in the three systems, and the results indicate that for scavenging by MV²⁺ the rate constants are decreased in the micelle systems (k in H₂O, 8.4 × 10¹⁰; CTAB, 3.5 × 10¹⁰ and SDS, 1.58 × 10¹⁰ M⁻¹ s⁻¹), whereas for NO₃⁻ the CTAB micelle decreases while the SDS micelle enhances the scavenging compared to water solution (k in H₂O, 8.3 × 10⁹; CTAB, 7 × 10⁸; and SDS, 2.05 × 10¹⁰ M⁻¹ s⁻¹). For the comproportionation reaction between Fe(bipy)₂(CN)₂⁺ and Fe(bipy)₂(CN)₂⁻ both micelles reduce the rate (k in H₂O, 3.3 × 10¹⁰; CTAB, 2.3 × 10¹⁰; and SDS, 1.05 × 10¹⁰ M⁻¹s⁻¹), but while the reaction of Fe(bipy)₂(CN)₂⁺ with MV⁺ is increased in CTAB compared to water, it is slowed in SDS (k in H₂O, 2.4 × 10¹⁰; CTAB, 8.9 × 10¹⁰; and SDS, 1.8 × 10¹⁰ M⁻¹s⁻¹). All effects observed in these microheterogeneous systems can be uniformly interpreted in terms of Coulombic interactions between the actual reactants and the charged surface of the micelles.     

Fabrication of Fe(CN)63− Functionalized PDDA/CdTe Layer‐by‐layer Film with Good Electron Transfer Ability

(PDDA/CdTe)_n layer‐by‐layer (LBL) film immobilized with Fe(CN)₆^3? was fabricated on the gold electrode. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were used to investigate the electrochemical properties of this film. The peak current of the immobilized Fe(CN)₆^3? increased as the number of the bilayers increased and was proportional to the scan rate. Compared with pure (PDDA/CdTe)_n and (PDDA/PSS)_n LBL film, Fe(CN)₆^3? immobilized (PDDA/CdTe)_n LBL film had good electron transfer ability. The immobility of Fe(CN)₆^3? into the film was attributed to its interaction with Cd²⁺ on the surface of CdTe QDs. Fe(CN)₆^3? also can interact with other metal ions, which would make Fe(CN)₆^3? release from the film. The concentrations of metal ions will affect the CV response of Fe(CN)₆^3? immobilized LBL film. It has provided a novel prototype of device or sensor for quantitative detection of metal ions.