由镁、铝醇盐配合物合成纳米粒子MgAl2O4尖晶石

Mg and Al alkoxide complex was synthesized in a cell without battery separator by electrochemical dissolution of aluminum for 6 h and magnesium for 1.8 h at 45 ℃ in ethanol solution of 0.04 mol·dm^-3 (Bu₄N)Br with a current density of 100 mA·cm^-2. IR and Raman spectroscopy were used to characterize the structure of the precursor of MgAl₂O₄. The results show that the current efficiency attains 98.4% and the precursor is MgAl₂(OCH₂CH₃)₅(acac)₃. The acac^- group-containing precursor could prevent it from agglomeration. The xerogel was obtained by drying in vacuum for 24 h and hydrolysis under pH≈8.5 of the precursor, which was heated at 350 ℃ for 2 h to obtain the nano-MgAl₂O₄ powder. XRD and TEM were used to investigate the structure of nano-MgAl₂O₄. The result suggests that the xerogel with an average particle size of 10 nm and the Nano-sized Spinel MgAl₂O₄ Particle of 12 nm thus obtained are with high purity.     

有机体系中电合成纳米PbTiO3粉体及表征

The precursor PbTi(OCH₂CH₃)_6-y(acac)_y for the mixed oxide PbTiO₃was synthesized by electrochemical dissolution of Lead and Titanium with a 1∶2 electricity quality in ethanol and acetyl-acetone solution. Nano-sized PbTiO₃powder was prepared by drying and calcining the xerogel from a direct sol-gel hydrolyzation of the precursor solution under pH of 8.5. The FTIR, TG-DTA, XRD and TEM were employed to characterize the structure of the precursor and nano-sized PbTiO₃. The results showed that the optimized conditions for the preparation of nano-sized PbTiO₃ were the electrolysis of the Lead plate and Titanium plate at 50 ℃ and 40 ℃ respectively under 0.03mol·dm^-3Bu₄NBr solution. The nano-sized PbTiO₃prepared by electrolysis exhibited a dispersive structure with an average diameter of 10 to 15 nm.     

N2O活化的Fe/ZSM-5表面活性氧的表征(英)

Temperature-programmed reduction (H₂-TPR) was employed to quantitatively characterize the active oxygen species generated from a high Fe-loading Fe/ZSM-5 catalyst exposed to N₂O at 250 ℃. [Fe-O-Fe]²⁺ dimer was determined as the active iron complex for N₂O decomposition to produce the active oxygen. Reduction of Fe³⁺ to Fe²⁺ by H₂ in the dimer and removal of OH^- groups from Fe²⁺ dimer by heating Fe/ZSM-5 to 700 ℃ were the prerequisites for the formation of this active Fe complex. A linear correlation with a slope of 1.0 between the amount of [Fe-O-Fe]²⁺ and that of active oxygen species was observed. Maximum amount of active oxygen species can be generated by reducing Fe/ZSM-5 catalyst with H₂ at the temperatures over 500 ℃ and then heating the resulting product in Ar to 700 ℃, followed by N₂O exposure at 250 ℃. The ratio of the total number of oxygen atoms (Ode) deposited by interaction of [Fe-O-Fe]²⁺ with N₂O to the amount of [Fe-O-Fe]²⁺ was 2. However, not all the deposited oxygen atoms were active oxygen (O_a); the ratio of O_a and O_de was 0.5. The iron dimer complex composing active oxygen is a five-atom ion [Fe₂O₃]²⁺; the most probable structure is as follows:     

有机溶液中电化学制备纳米MgTiO3

In a cell without separating the cathode and anode spaces, the precursor MgTi(OCH₂CH₃)_(6-y)(acac)_y of the mixed oxide MgTiO₃ was directly synthesized by electrochemical dissolution of titanium for 4 hours and then of magnesium for 1 hour 40 minutes at the current of 0.2 A in ethanol and acetyl-acetone solution. The nano- MgTiO₃ powder was prepared by a direct sol-gel process of the electrolyte solution under pH≈8.5 followed by washing, drying in vacuum for 24 h, and calcination at 500 ℃ for 2 h. IR and Raman spectroscopy, XRD, and TEM were used to investigate the structure of nano-MgTiO₃ and its precursor. The result suggested that it was more appropriate to control the temperature between 35～40 ℃ and the concentration of conductive additive (Bu₄N)Br at 0.04 mol·L^-1. The xerogel with an average particle size of 12 nm and the nano-MgTiO₃ of 20 nm was thus obtained in a high purity.     

电化学法制备高热稳定性锐钛矿型纳米TiO2

Titanium alkoxides were prepared by anodic dissolution of metallic titanium in absolute ethanol in the presence of HN(C₂H₅)₂*HCl (electro－conductive additives).The solution was directly hydrolyzed to prepare nanocrystalline of TiO₂ (about 10nm)by a sol－gel process.The precursor gels was calcined at T=450 ℃ and 720 ℃for 30 min,and nanocrystalline of TiO₂ (anatase) with high textural and thermal stability was obtained.FTIR,XRD,TEM,were used to characterize the structure of titanium alkoxides and nanocrystalline of TiO₂.The characteristics of nanocrystalline of TiO₂ was depended on the properties of titanium alkoxides.The Ti(OEt)₄ as a source of titanium yielded the best textural and thermal stability nanocrystalline of TiO₂.     

针状TiO2锐钛矿晶粒溶胶的制备、结构及形成机理研究

The PTA sol was prepared using titanyl sulfate(TiOSO₄), peroxide (H₂O₂) and ammonia (NH₃·H₂O) as raw materials. The semitransparent, light yellow AS(autoclaved sol) with ultra-fine needle-like anatase crystals was synthesized by autoclaving the PTA sol at 80～100 ℃ for different times. The anatase crystals were needle-like and 80 nm in length, 20～30 nm in diameter. The FTIR, XRD, SEM were used to analyse the chemical structure, properties of the AS and influencing factors during the sol preparation. The mechanism model of the AS formation was established based on the inorganic and crystal structural chemistry. The PTA molecules were decomposed to form Ti⁴⁺ under hydrothermal conditions and the Ti⁴⁺ were hydrated with water to get [Ti(OH)₄(OH₂)₂]⁰, a growing units of the anatase crystals. The appearance of the needle-like anatase crystals and the anatase precipitate are also explained in this paper.     

Ce0.8Y0.2O1.9-Ca3(PO4)2-K3PO4复合电解质在中温区的质子导电性及在常压合成氨中的应用

A precursor of Ce_0.8Y_0.2O_1.9(YDC) solid electrolyte was synthesized by the gol-gel method. YDC and phosphates powders were prepared by mixing the YDC and phosphates according to different weight ratios. The mixtures of the YDC and binary phosphates were ground and sintered at 1 400 ℃. The proton conductivity in solid electrolyte of the sintered samples was examined using electrochemical methods at 400～800 ℃. Ammonia was synthesized from nitrogen and hydrogen at atmospheric pressure in the solid state proton conducting cell reactor. The optimal condition for the ammonia production was determined. The result indicated that composite electrolyte of 80wt% YDC: 20wt% binary phosphates as proton conductor could obtain the highest ionic conductivity and ammonia production rate among the four samples, the rate of evolution of ammonia was up to 9.5 × 10^-9 mol·s^-1·cm^-2.     

[Ru(bpy)2tpphz]2+与Zn2+形成的双核配合物的荧光性质研究

The formation of heterobimetallic ruthenium(Ⅱ) complex was investigated by absorption and emission spectra. As an intercalator of DNA， the luminescent monometallic ruthenium(Ⅱ) complex [Ru(bpy)₂tpphz]²⁺ could coor-dinate with Zn²⁺ to form the nonluminescent heterobimetallic complex [Ru(bpy)₂(tpphz)Zn]⁴⁺. The emission in-tensity of complex decreased as increasing the amounts of Zn²⁺ and the luminescence was almost lost at the ratio of [Zn]/[Ru] of 1. After binding to DNA， the peripheral coordination site on the tpphz ligand remained accessible for Zn²⁺， the coordination occurred from the oppsite side of helix with respect to intercalated [Ru(bpy)₂tpphz]²⁺ and the nonluminescent heterobimetallic complex was formed. On the other hand， the [Ru(bpy)₂(tpphz)Zn]⁴⁺ also bound to DNA by intercalation and situated the region of the intercalated [Ru(bpy)₂tpphz]²⁺ between the base pairs of DNA. The complex looked like a molecular nut (the Zn²⁺) and bolt (the [Ru(bpy)₂tpphz]²⁺).     

纳米BaFe12O19永磁铁氧体的制备、结构和磁性的研究

In this paper, the nanometer permanent magnetic BaFe₁₂O₁₉ powder was synthesized by a novel method of independent nucleation and crystallization steps and subsequent heat treatment,during the synthesis, Ba(NO₃)₂, Fe(NO₃)₂ and NH₄HCO₃·NH₂COONH₄ were used as starting materials. The effect of crystallization process and heat treatment conditions on the particle size, microstructure and magnetic properties of powder was studied by using XRD, TEM and vibration sample magnetometometer techniques.XRD results showed that the hematite, α-Fe₂O₃, was the main phase in the powder at heat treatment temperatures below 650℃ and its amount in the powder was decreased with increasing temperature and small amount of α-Fe₂O₃ was still remained after being heated at 900℃ for 8hrs. BaFe₁₂O₁₉ was formed about 650℃ and its amount increased in the powder as temperature raised and the higher temperature was needed to attain considerable amount of BaFe₁₂O₁₉ and ideal nanometer BaFe₁₂O₁₉ particle in the powder. The temperature between 40℃～60℃ in the crystallization process was favor to the formation of good BaFe₁₂O₁₉ crystal and to the good magnetic properties of the powder. TEM showed that the particle size in the powder increased with the enhancement of the temperature and the powder crystallized at 40℃ and heated at 800℃ for 8hrs afterwards had a very homogenous particle size distribution, and that the powder heated at 900℃ for 8hrs with the same crystalline condition as the former had a typical hexagonal shape and a chain aggregation. Specific saturation and residential magnetizations and coercive force of the powder increased mono-tonically with the increase of temperature, and reached 39.86A·m²·kg^-1, 23.96A·m²·kg^-1, 480kA·mg^-1 at 900℃, respectively.     

梯度材料LiNi0.8Co0.2O2的合成与表征

The gradient composite LiNi_0.8Co_0.2O₂ was synthesized using spherical Ni(OH)₂ particle coated by a sol-gel containing cobalt and lithium. The precursor was examined by DSC-TG. The gradient composite was characterized by SEM, EDS, XPS, XRD and ICP-AES. The XPS, EDS and ICP-AES results show that content of cobalt in the surface is higher than in the center of the spherical particle of the gradient composite. The first discharge specific capacity of the gradient composite sintered at 700 ℃ is 187.3 mAh·g^-1.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.