Immobilized Fullerene C60‐Enzyme‐Based Electrochemical Glucose Sensor

A mixed‐valence cluster of cobalt(II) hexacyanoferrate and fullerene C60‐enzyme‐based electrochemical glucose sensor was developed. A water insoluble fullerene C60‐glucose oxidase (C60‐GOD) was prepared and applied as an immobilized enzyme on a glassy carbon electrode with cobalt(II) hexacyanoferrate for analysis of glucose. The glucose in 0.1 M KCl/phosphate buffer solution at pH = 6 was measured with an applied electrode potential at 0.0 mV (vs Ag/AgCl reference electrode). The C60‐GOD‐based electrochemical glucose sensor exhibited efficient electro‐catalytic activity toward the liberated hydrogen peroxide and allowed cathodic detection of glucose. The C60‐GOD electrochemical glucose sensor also showed quite good selectivity to glucose with no interference from easily oxidizable biospecies, e.g. uric acid, ascorbic acid, cysteine, tyrosine, acetaminophen and galactose. The current of H₂O₂ reduced by cobalt(II) hexacyanoferrate was found to be proportional to the concentration of glucose in aqueous solutions. The immobilized C60‐GOD enzyme‐based glucose sensor exhibited a good linear response up to 8 mM glucose with a sensitivity of 5.60 × 10² nA/mM and a quite short response time of 5 sec. The C60‐GOD‐based glucose sensor also showed a good sensitivity with a detection limit of 1.6 × 10^‐6 M and a high reproducibility with a relative standard deviation (RSD) of 4.26%. Effects of pH and temperature on the responses of the immobilized C60‐GOD/cobalt(II) hexacyanoferrate‐based electrochemical glucose sensor were also studied and discussed.     

MOF‐Derived Spinel NiCo2O4 Hollow Nanocages for the Construction of Non‐enzymatic Electrochemical Glucose Sensor

Non‐enzymatic glucose sensor is greatly expected to take over its enzymatic counterpart in the future. In this paper, we reported on a facile strategy to construct a non‐enzymatic glucose sensor by use of NiCo₂O₄ hollow nanocages (NiCo₂O₄ HNCs) as catalyst, which was derived from Co‐based zeolite imidazole frame (ZIF‐67). The NiCo₂O₄ HNCs modified glassy carbon electrode (NiCo₂O₄ HNCs/GCE), the key component of the glucose sensor, showed highly electrochemical catalytic activity towards the oxidation of glucose in alkaline media. As a result, the proposed non‐enzymatic glucose sensor afforded excellent analytical performances assessed with the aid of cyclic voltammetry and amperometry (i–t). A wide linear range spanning from 0.18 μΜ to 5.1 mM was achieved at the NiCo₂O₄ HNCs/GCE with a high sensitivity of 1306 μA mM^?1 cm^?2 and a fast response time of 1 s. The calculated limit of detection (LOD) of the sensor was as low as 27 nM (S/N=3). Furthermore, it was demonstrated that the non‐enzymatic glucose sensor showed considerable anti‐interference ability and excellent stability. The practical application of the sensor was also evaluated by determination of glucose levels in real serum samples.     

Binderless Solution Processed Zn Doped Co3O4 Film on FTO for Rapid and Selective Non‐enzymatic Glucose Detection

A simple solution based deposition process has been used to fabricate Zn doped Co₃O₄ electrode as an electrocatalyst for non‐enzymatic oxidation of glucose. XRD, HRTEM, SEM, EELS, AFM, EIS was used to characterise the electrode. The addition of Zn as dopant on Co₃O₄ resulted in enhanced electrochemical performance of Zn:Co₃O₄ material compared to pristine Co₃O₄ due to increased charge transferability. The as prepared electrode showed fast response (<7 s) time, good sensitivity (193 μA mM⁻¹ cm⁻²) in the linear range of 5 μM–0.62 mM, good selectivity towards glucose at a relatively lower applied potential of +0.52 V in 0.1 M NaOH solution. A detection limit of ∼2 μM was measured for the Zn:Co₃O₄ electrode. The applied fabrication method resulted in good inter and intra electrode reproducibility as was shown by the lower relative standard deviation values (R.S.D). The electrode retained 70 % of initial current response after 30 days. Although the as prepared Zn:Co₃O₄ electrodes did not result in highest reported sensitivity, and lowest limit of detection; the ease of fabrication and scalability of production, good inter and intra electrode reproducibility makes it a potential candidate for commercial application as glucose sensor.     

Nickel Hydroxide and Intercalated Graphene with Ionic Liquid Nanocomposite‐modified Electrode for Sensing of Glucose

A novel non‐enzymatic glucose sensor based on nickel hydroxide and intercalated graphene with ionic liquid (G‐IL) nanocomposite modified glass carbon electrode was fabricated. Scanning electron microscope, Fourier transform infrared spectra and energy dispersive X‐ray spectroscopy of the nanocomposite confirmed the morphology and ingredient of Ni(OH)₂ as well as G‐IL. Moreover, experimental results of cyclic voltammetry, electrochemical impedance spectroscopy and chronoamperometry indicated the sensing properties of Ni(OH)₂ at Ni(OH)₂/G‐IL modified electrode towards the typical electrocatalytic oxidation process of glucose at 0.43 V in 0.10 M NaOH. The current response was linearly related to glucose concentration in a range from 0.5 to 500 μM with a detection limit of 0.2 μM (S/N = 3) and sensitivity of 647.8 μA mM^?1 cm^?2. The response time of the sensor to glucose was less than 2 s. This work may be expected to develop an excellent electrochemical sensing platform of G‐IL as a catalysis carrier.     

A Non‐Enzymatic Hydrogen Peroxide Sensor Based on Gold Nanoparticles/Carbon Nanotube/Self‐Doped Polyaniline Hollow Spheres

In this study, a novel non‐enzymatic hydrogen peroxide (H₂O₂) sensor was fabricated based on gold nanoparticles/carbon nanotube/self‐doped polyaniline (AuNPs/CNTs/SPAN) hollow spheres modified glassy carbon electrode (GCE). SPAN was in‐site polymerized on the surface of SiO₂ template, then AuNPs and CNTs were decorated by electrostatic absorption via poly(diallyldimethylammonium chloride). After the SiO₂ cores were removed, hollow AuNPs/CNTs/SPAN spheres were obtained and characterized by transmission electron microscopy (TEM), field‐emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR). The electrochemical catalytic performance of the hollow AuNPs/CNTs/SPAN/GCE for H₂O₂ detection was evaluated by cyclic voltammetry (CV) and chronoamperometry. Using chronoamperometric method at a constant potential of ?0.1 V (vs. SCE), the H₂O₂ sensor displays two linear ranges: one from 5 µM to 0.225 mM with a sensitivity of 499.82 µA mM^?1 cm^?2; another from 0.225 mM to 8.825 mM with a sensitivity of 152.29 µA mM^?1 cm^?2. The detection limit was estimated as 0.4 µM (signal‐to‐noise ratio of 3). The hollow AuNPs/CNTs/SPAN/GCE also demonstrated excellent stability and selectivity against interferences from other electroactive species. The sensor was further applied to determine H₂O₂ in disinfectant real samples.     

Novel Sn Doped Co3O4 Thin Film for Nonenzymatic Glucose Bio‐Sensor and Fuel Cell

A facile chemical solution deposition via two‐step spin coating technique was used to fabricate nano‐particulate novel Sn doped Co₃O₄ thin film for glucose sensor and fuel cell applications. Substitution of Sn into Co₃O₄ host lattice lead to a remarkable increase in the electrocatalytic activity of the Co₃O₄ electrode material. Film thickness played a significant role in enhancing the charge transferability of the electrode as was observed from electrochemical impedance spectroscopy (EIS). The best sensor exhibited two wide linear response ranges (2 μM up to ∼0.5 mM and 0.6 mM up to ∼5.5 mM respectively) with sensitivities of 921 and 265 μA cm⁻² mM⁻¹ respectively and low limit of detection of 100 nM (S/N=3). The sensor was very selective towards glucose in the presence of various interference and showed long term stability. Moreover, the developed thin film modified electrode could generate one electron current in nonenzymatic fuel cell setup at room temperature.     

Porous ZnO/Co3O4/N‐doped carbon nanocages synthesized via pyrolysis of complex metal–organic framework (MOF) hybrids as an advanced lithium‐ion battery anode

Metal oxides have a large storage capacity when employed as anode materials for lithium‐ion batteries (LIBs). However, they often suffer from poor capacity retention due to their low electrical conductivity and huge volume variation during the charge–discharge process. To overcome these limitations, fabrication of metal oxides/carbon hybrids with hollow structures can be expected to further improve their electrochemical properties. Herein, ZnO‐Co₃O₄ nanocomposites embedded in N‐doped carbon (ZnO‐Co₃O₄@N‐C) nanocages with hollow dodecahedral shapes have been prepared successfully by the simple carbonizing and oxidizing of metal–organic frameworks (MOFs). Benefiting from the advantages of the structural features, i.e. the conductive N‐doped carbon coating, the porous structure of the nanocages and the synergistic effects of different components, the as‐prepared ZnO‐Co₃O₄@N‐C not only avoids particle aggregation and nanostructure cracking but also facilitates the transport of ions and electrons. As a result, the resultant ZnO‐Co₃O₄@N‐C shows a discharge capacity of 2373 mAh g^?1 at the first cycle and exhibits a retention capacity of 1305 mAh g^?1 even after 300 cycles at 0.1 A g^?1. In addition, a reversible capacity of 948 mAh g^?1 is obtained at a current density of 2 A g^?1, which delivers an excellent high‐rate cycle ability.     

Cobalt‐Doped Perovskite‐Type Oxide LaMnO3 as Bifunctional Oxygen Catalysts for Hybrid Lithium–Oxygen Batteries

Perovskite‐type oxides based on rare‐earth metals containing lanthanum manganate are promising catalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in alkaline electrolyte. Perovskite‐type LaMnO₃ shows excellent ORR performance, but poor OER activity. To improve the OER performance of LaMnO₃, the element cobalt is doped into perovskite‐type LaMnO₃ through a sol–gel method followed by a calcination process. To assess electrocatalytic activities for the ORR and OER, a series of LaMn_1?xCo_xO₃ (x=0, 0.05, 0.1, 0.2, 0.3, 0.4, and 0.5) perovskite oxides were synthesized. The results indicate that the amount of doped cobalt has a significant effect on the catalytic performance of LaMn_1?xCo_xO₃. If x=0.3, LaMn_0.7Co_0.3O₃ not only shows a tolerable electrocatalytic activity for the ORR, but also exhibits a great improvement (>200 mV) on the catalytic activity for the OER; this indicates that the doping of cobalt is an effective approach to improve the OER performance of LaMnO₃. Furthermore, the results demonstrate that LaMn_0.7Co_0.3O₃ is a promising cost‐effective bifunctional catalyst with high performance in the ORR and OER for application in hybrid Li?O₂ batteries.     

Ag−Co3O4 @ Nr GO Material Synthesized by One‐pot Hydrothermal Method for Carcinoembryonic Antigen (CEA) Detection of Enzyme‐mimetic Electrochemical Immunosensor

A high‐sensitivity carcinoembryonic antigen immunosensor was successfully prepared via a one‐step hydrothermal method, wherein nitrogen‐doped graphene oxide (Nr GO) loaded Ag and Co₃O₄ nanomaterials were synthesized using ammonia as the nitrogen source. Doping nitrogen atoms into the graphene structure forms a new type of N‐type semiconductor with an increased number of graphene layers and more active sites for bonding with chemicals, thereby providing excellent in biocompatibility and good electrical conductivity. The electrical signal of the sensor is further amplified due to the good catalytic effect of Co₃O₄ and Ag NPs on H₂O₂. The signal probe requires neither pretreatment nor acid treatment, and can be easy to loaded with metal‐immobilized antibodies, which greatly simplifies the detection step not shorten the detection time. The sensor has good sensitivity to detecting carcinoembryonic antigen (CEA) and can easily operate, and requires mild reaction conditions. Under optimal experimental conditions, the linear range of the sensor is 0.001–200 ng ? mL^?1, the detection limit is 0.18 pg ? mL^?1, and the linear correlation coefficient is 0.991, which can be used for CEA determination of the actual sample.     

Electrochemical Fabrication of Cobalt Oxides/Nanoporous Gold Composite Electrode and its Nonenzymatic Glucose Sensing Performance

A nonenzymatic glucose sensor was successfully established by electrochemically decorating cobalt oxides (CoO_x) on a nanoporous gold electrode (NPG) using cobalt hexacyanoferrate (CoHCF) as a precursor. It exhibited high sensitivity and long‐term stability as well as satisfactory quantification of glucose concentration in human serum samples. The morphology and surface analysis of the resulting CoO_x/NPG were carefully characterized. Two detection methods, cyclic voltammetry and amperometry, were employed to evaluate the performance of CoO_x/NPG towards glucose sensing in alkaline solution. Using cyclic voltammetry, at ?0.5 V, the glucose partial oxidation peak current is linear to the glucose concentration up to 14 mM with a sensitivity of 283.7 µA mM^?1 cm^?2. A linear amperometric response at 0.55 V was obtained in the glucose concentration range from 2 µM to 2 mM with a sensitivity of 2025 µA mM^?1 cm^?2 and a response time <3 s.     

Heterostructured Inter‐Doped Ruthenium–Cobalt Oxide Hollow Nanosheet Arrays for Highly Efficient Overall Water Splitting

The development of transition‐metal‐oxides (TMOs)‐based bifunctional catalysts toward efficient overall water splitting through delicate control of composition and structure is a challenging task. Herein, the rational design and controllable fabrication of unique heterostructured inter‐doped ruthenium–cobalt oxide [(Ru–Co)O_x] hollow nanosheet arrays on carbon cloth is reported. Benefiting from the desirable compositional and structural advantages of more exposed active sites, optimized electronic structure, and interfacial synergy effect, the (Ru–Co)O_x nanoarrays exhibited outstanding performance as a bifunctional catalyst. Particularly, the catalyst showed a remarkable hydrogen evolution reaction (HER) activity with an overpotential of 44.1 mV at 10 mA cm^?2 and a small Tafel slope of 23.5 mV dec^?1, as well as an excellent oxygen evolution reaction (OER) activity with an overpotential of 171.2 mV at 10 mA cm^?2. As a result, a very low cell voltage of 1.488 V was needed at 10 mA cm^?2 for alkaline overall water splitting.     

Highly Responsive and Selective Ethanol Gas Sensor Based on Co3O4-Modified SnO2 Nanofibers

SnO₂ nanofibers were synthesized by electrospinning and modified with Co₃O₄ via impregnation in this work. Chemical composition and morphology of the nanofibers were systematically characterized, and their gas sensing properties were investigated. Results showed that Co₃O₄ modification significantly enhanced the sensing performance of SnO₂ nanofibers to ethanol gas. For a sample with 1.2 mol% Co₃O₄, the response to 100 ppm ethanol was 38.0 at 300℃, about 6.7 times larger than that of SnO₂ nanofibers. In addition, the response/recovery time was also greatly reduced. A power-law dependence of the sensor response on the ethanol concentration as well as excellent ethanol selectivity was observed for the Co₃O₄/SnO₂ sensor. The enhanced ethanol sensing performance may be attributed to the formation of p-n heterojunctions between the two oxides.     

Enhanced Electrochemical Capacitive Properties of Nickel‐Cobalt Oxide Nano‐flakes Materials

Nickel‐cobalt oxide nano‐flakes materials are successfully synthesized by a facile chemical co‐precipitation method followed by a simple calcination process. The studies show that the as‐prepared nickel‐cobalt oxides with different Ni/Co ratio are composed of NiO and Co₃O₄ compounds. The Co_0.56Ni_0.44 oxide material, which exhibits a mesoporous structure with a narrow distribution of pore size from 2 to 7 nm, possesses markedly enhanced charge‐discharge properties at high current density compared with the pure NiO and pure Co₃O₄. The Co_0.56Ni_0.44 oxide electrode shows a specific capacitance value of 1227 F/g at 5 mA/cm², which is nearly three times greater than that of the pure NiO electrode at the same current density.     

Synthesis of Tri‐functional Core‐shell CuO@carbon Quantum Dots@carbon Hollow Nanospheres Heterostructure for Non‐enzymatic H2O2 Sensing and Overall Water Splitting Applications

A core‐shell structure with CuO core and carbon quantum dots (CQDs) and carbon hollow nanospheres (CHNS) shell was prepared through facile in‐situ hydrothermal process. The composite was used for non‐enzymatic hydrogen peroxide sensing and electrochemical overall water splitting. The core‐shell structure was established from the transmission electron microscopy image analysis. Raman and UV‐Vis spectroscopy analysis confirmed the interaction between CuO and CQDs. The electrochemical studies showed the limit of detection and sensitivity of the prepared composite as 2.4 nM and 56.72 μA μM^?1 cm^?2, respectively. The core‐shell structure facilitated better charge transportation which in turn exhibited elevated electro‐catalysis towards hydrogen evolution reaction (HER), oxygen evolution reaction (OER) and overall water splitting. The overpotential of 159 mV was required to achieve 10 mA cm^?2 current density for HER and an overpotential of 322 mV was required to achieve 10 mA cm^?2 current density for OER in 1.0 M KOH. A two‐electrode system was constructed for overall water splitting reaction, which showed 10 and 50 mA cm^?2 current density at 1.83 and 1.96 V, respectively. The prepared CuO@CQDs@CHNS catalyst demonstrated excellent robustness in HER and OER catalyzing condition along with overall water splitting reaction. Therefore, the CuO@CQDs@CHNS could be considered as promising electro‐catalyst for H₂O₂ sensing, HER, OER and overall water splitting.     

Fabrication of Hierarchically Structured MOF‐Co3O4 on Well‐aligned CuO Nanowire with an Enhanced Electrocatalytic Property

Engineering appropriate shape and size of three‐dimensional inorganic nanostructures materials is of one the main critical problems in pursuing high‐performance electrode materials. Herein, we fabricate a metal‐organic framework derived cobalt oxide (Co₃O₄) are grown on copper oxide nanowire (CuO NWs) supported on the surface of 3D copper foam substrate. The highly aligned CuO NWs were prepared by using electrochemical anodization of copper foam in ambient temperature and followed by MOF Co₃O₄ was grown via a simple in situ solution deposition then consequent calcination process. The obtained binder‐free 3D CuO NWs@Co₃O₄ nanostructures were further characterized by using X‐ray diffraction, X‐ray photoelectron spectroscopy, field‐emission scanning electron microscopy, and transmission electron microscopy. Furthermore, electrochemical sensing of glucose was studied by using Cyclic Voltammetry, and chronoamperometry techniques. Interestingly, 3D CuO NWs@Co₃O₄ electrode exhibits excellent performance for the oxidation of glucose compared with individual entities. The proposed sensor shows wide linear ranges from 0.5 μM to 0.1 mM with the sensitivity of 6082 μA/μM and the lowest detection limit (LOD) of 0.23 μM was observed with the signal to noise ratio, (S/N) of 3. The superior catalytic oxidation of glucose mainly is endorsed by the excellent electrical conductivity and synergistic effect of the Co₃O₄ and CuO NWs.     

Hollow Nanotubes of N‐Doped Carbon on CoS

Low‐cost, single‐step synthesis of hollow nanotubes of N‐doped carbon deposited on CoS is enabled by the simultaneous use of three functionalities of polyacrylonitrite (PAN) nanofibers: 1) a substrate for loading active materials, 2) a sacrificial template for creating hollow tubular structures, and 3) a precursor for in situ nitrogen doping. The N‐doped carbon in hollow tubes of CoS provides a high‐capacity anode of long cycle life for a rechargeable Li‐ion or Na‐ion battery cell that undergoes the conversion reaction 2 A⁺+2 e^?+CoS →Co+A₂S with A=Li or Na.     

Self‐assembly of p‐Aminothiophenol on Gold Surface: Application for Impedimetric and Potentiometric Sensing of Cobalt (II) Ions – A Comparative Study

Cobalt, despite an essential biological element, imposes threat to humans when exposed to high concentration or even to low concentration for long term which demands the development of highly sensitive and selective analytical methods for its trace analysis. In the present work, self‐assembly of p‐aminothiophenol (p‐ATP) on gold surface (Au?ATP SAM) was carried out and for the first time, applied as a platform for impedimetric and potentiometric sensing of Co²⁺. Au?ATP SAM was characterized using electrochemical techniques: cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), in the presence of two redox probes: [Fe(CN)₆]^3?/4? and [Ru(NH₃)₆]^2+/3+ to evaluate associated passivating behaviour. Au?ATP SAM completely blocked [Fe(CN)₆]^3?/4? as compared to [Ru(NH₃)₆]^2+/3+ which may be attributed to inner‐sphere and outer‐sphere ET mechanisms, respectively. Au?ATP SAM was found to exhibit excellent sensitivity towards Co²⁺ in a wider concentration range from 1.0×10^?12 M to 1.0×10^?5 M (r²=0.963) at pH 5.5 with a detection limit of 6.0×10^?13 M and superior selectivity. Further, carbon paste electrode (CPE) was prepared by incorporating p‐ATP bound gold nanoparticles and explored for potentiometric sensing of Co²⁺ which exhibited Nernstian slope of 29.2±0.2 mV/dec in linear concentration range of 1.0×10^?6 M–1.0×10^?1 M (r²=0.971) with a detection limit of 8.0×10^?7 M. The proposed sensors were successfully applied for estimation of Co²⁺ content in water samples.     

Self‐Template Synthesis of Hybrid Porous Co3O4–CeO2 Hollow Polyhedrons for High‐Performance Supercapacitors

In this work, hybrid porous Co₃O₄–CeO₂ hollow polyhedrons have been successfully obtained via a simple cation‐exchange route followed by heat treatment. In the synthesis process, ZIF‐67 polyhedron frameworks are firstly prepared, which not only serve as a host for the exchanged Ce3⁺ ions but also act as the template for the synthesis of hybrid porous Co₃O₄–CeO₂ hollow polyhedrons. When utilized as electrode materials for supercapacitors, the hybrid porous Co₃O₄–CeO₂ hollow polyhedrons delivered a large specific capacitance of 1288.3 F g^?1 at 2.5 A g^?1 and a remarkable long lifespan cycling stability (<3.3 % loss after 6000 cycles). Furthermore, an asymmetric supercapacitor (ASC) device based on hybrid porous Co₃O₄–CeO₂ hollow polyhedrons was assembled. The ASC device possesses an energy density of 54.9 W h kg^?1, which can be retained to 44.2 W h kg^?1 even at a power density of 5100 W kg^?1, indicating its promising application in electrochemical energy storage. More importantly, we believe that the present route is a simple and versatile strategy for the preparation of other hybrid metal oxides with desired structures, chemical compositions and applications.     

A MnOOH‐Polyaniline Nanocomposite Modified Gold Electrode for Electrochemical Sensing of Nitrite

A novel non‐enzymatic nitrite sensor was fabricated by immobilizing MnOOH‐PANI nanocomposites on a gold electrode (Au electrode). The morphology and composition of the nanocomposites were investigated by transmission electron microscopy (TEM ) and Fourier transform infrared spectrum (FTIR ). The electrochemical results showed that the sensor possessed excellent electrocatalytic ability for NO₂⁻ oxidation. The sensor displayed a linear range from 3.0 μmol•L⁻¹ to 76.0 mmol•L⁻¹ with a detection limit of 0.9 μmol•L⁻¹ (S/N = 3), a sensitivity of 132.2 μA •L•mol⁻¹•cm⁻² and a response time of 3 s. Furthermore, the sensor showed good reproducibility and long‐term stability. It is expected that the MnOOH‐PANI nanocomposites could be applied for more active sensors and used in practice for nitrite sensing.     

Redox‐Inert Fe3+ Ions in Octahedral Sites of Co‐Fe Spinel Oxides with Enhanced Oxygen Catalytic Activity for Rechargeable Zinc–Air Batteries

Bimetallic cobalt‐based spinel is sparking much interest, most notably for its excellent bifunctional performance. However, the effect of Fe³⁺ doping in Co₃O₄ spinel remains poorly understood, mainly because the surface state of a catalyst is difficult to characterize. Herein, a bifunctional oxygen electrode composed of spinel Co₂FeO₄/(Co_0.72Fe_0.28)_Td(Co_1.28Fe_0.72)_OctO₄ nanoparticles grown on N‐doped carbon nanotubes (NCNTs) is designed, which exhibits superior performance to state‐of‐the‐art noble metal catalysts. Theoretical calculations and magnetic measurements reveal that the introduction of Fe³⁺ ions into the Co₃O₄ network causes delocalization of the Co 3d electrons and spin‐state transition. Fe³⁺ ions can effectively activate adjacent Co³⁺ ions under the action of both spin and charge effect, resulting in the enhanced intrinsic oxygen catalytic activity of the hybrid spinel Co₂FeO₄. This work provides not only a promising bifunctional electrode for zinc–air batteries, but also offers a new insight to understand the Co‐Fe spinel oxides for oxygen electrocatalysis.