Electron beam crosslinking of poly(ethylene-co-vinyl acetate)/clay nanocomposites

Effect of electron beam irradiation on the thermal and mechanical properties of poly(ethylene-co-vinyl acetate) (EVA)/clay nanocomposites prepared by melt blending method has been investigated. The hot set test results show that elongation at high temperature under static load decreased with the increase of irradiation dose. The tensile modulus increased continuously with increasing dose. While the tensile strength increased up to 100 kGy, it decreased with further increase in dose. The elongation at break decreased continuously with increasing dose. Thermogravimetric analysis showed that thermal stability of the EVA/clay nanocomposites improved with increasing dose. The improvement in the mechanical and thermal properties is attributed to the formation of radiation-induced crosslinking as evidenced by the gel content results.     

Characterization of irradiation-induced crosslink of epoxidised natural rubber/ethylene vinyl acetate (ENR-50/EVA) blend

The effect of irradiation on tensile, dynamic mechanical properties, thermal properties and morphology of ENR-50, EVA and ENR-50/EVA blend was investigated. All the samples were irradiated using a 3.0 MeV electron beam (EB) machine with doses ranging from 20 to 100 kGy. Results indicate that the gel fraction of ENR-50, EVA and ENR-50/EVA blend increases with irradiation dose. Concerning tensile properties, it can be seen that EB radiation increases the tensile strength of all the samples, increases the elongation at break of ENR-50 and ENR-50/EVA blend, reduces the elongation at break of EVA, increases M200 (modulus at 200% strain) of ENR-50 and EVA, while decreases M200 of the ENR-50/EVA blend. For dynamic mechanical studies, it was found that EB radiation increases the T_g of all the samples due to the effect of irradiation-induced crosslinking. The compatibility of ENR-50/EVA blend also found to be improving upon irradiation. In the case of thermal properties, it was detected that T_m, T_c and the degree of crystallinity of ENR-50/EVA blend increase with an increase in irradiation dose. This was due to the perfection in the crystal growth occurring upon radiation. Morphology changes play a major role in the changes of the properties of ENR-50/EVA blend. Finally, it can be concluded that ENR-50/EVA blend can be vulcanized by EB radiation.     

丙烯-乙烯共聚物/乙烯-1-辛烯共聚物层状复合材料的力学性能研究

利用自主设计的一套可进行微层共挤出的口模,分别制备了2层、16层、32层和64层丙烯-乙烯共聚物(PPE)/乙烯-1-辛烯共聚物(POE)交替层状复合材料。研究了制得的层状复合材料的应力-应变行为,利用等效盒子模型(equivalent box model)描述了层状复合材料与相应的常规PPE/POE共混材料力学行为的区别.通过对共挤出材料和共混材料的拉伸数据进行分析后发现,具有层状结构特别是多层结构的共挤出材料具有比共混材料更为优异的屈服和断裂伸长性能.     

Rheology, morphology and mechanical properties of polyethylene/ethylene vinyl acetate copolymer (PE/EVA) blends

Rheology, morphology and mechanical properties of binary PE and EVA blends together with their thermal behavior were studied. The results of rheological studies showed that, for given PE and EVA, the interfacial interaction in PE-rich blends is higher than EVA-rich blends, which in turn led to finer and well-distributed morphology in PE-rich blends. Using two different models, the phase inversion composition was predicted to be in 45 and 47 wt% of the PE phase. This was justified by morphological studies, where a clear co-continuous morphology for 50/50 blend was observed. The tensile strength for PE-rich blends showed positive deviation from mixing rule, whereas the 50/50 blend and EVA-rich blends displayed negative deviation. These results were in a good agreement with the results of viscoelastic behavior of the blends. The elongation at break was found to follow the same trend as tensile strength except for 90/10 PE/EVA blend. The latter was explained in terms of the effect of higher co-crystallization in 90/10 composition, which increased the tensile strength and decreased the elongation at break in this composition. The results of thermal behavior of the blends indicated that the melting temperatures of PE and EVA decrease and increase, respectively, due to the dilution effect of EVA on PE and nucleation effect of PE on EVA.     

Thermal,rheological, morphological and mechanical properties of high density polyethylene/ethylene vinyl acetate copolymer (HDPE/EVA) blends

Thermal, rheological, morphological and mechanical properties of binary HDPE and EVA blends were studied. The results of rheological studies showed that for given HDPE and EVA, the interfacial interaction in HDPE-rich blends is higher than EVA-rich blends. Using three different rheological criterions, the phase inversion composition was predicted to be in 30 wt% of the EVA phase. This showed good agreement with morphological studies. The tensile strength for HDPE-rich blends showed positive deviation from mixing rule, whereas the EVA-rich blends played negative deviation. These results were in a good agreement with the results of viscoelastic behavior of the blends. The thermal analysis revealed that high co-crystallizaiton in 90/10 composition, which increased the tensile strength and decreased the elongation at break in this composition. Furthermore, the results of thermal behavior of the blends indicated that the melting temperatures of HDPE decrease due to the dilution effect of EVA on HDPE.     

兼具导热和自修复功能的聚合物复合材料

针对聚合物复合材料存在的结构受损导致导热和力学强度降低的问题,提出利用导热填料增强自修复聚合物,实现导热性能和力学强度的快速修复.通过对双(3-氨丙基)封端的聚二甲基硅氧烷(H2N-PDMS-NH2)进行端基改性,得到脲基嘧啶酮(UPy)双封端的聚二甲基硅氧烷(UPy-PDMS-UPy),于60℃下20 h后拉伸强度修复效率可达86.6%.进一步填充羟基化氮化硼(mBN)制备兼具自修复功能的导热复合材料,研究发现mBN的填充导致复合材料强度提高但韧性降低,对导热性能和自修复功能分别起积极和不利影响.当mBN含量为30 wt%时,热导率高达2.579 W·m^?1·K^?1,于60℃下40 h后拉伸强度修复效率达82.0%.红外热像仪显示,损伤处接触10 h后,mBN-30/UPy-PDMS-UPy上表面温度接近初始温度,展现出导热通路的修复特征,实现导热与自修复功能的兼备.     

微层共挤出(PP+EVOH)/PP阻隔材料的结构与性能研究

利用微层共挤出技术制备了具有交替层状结构的(PP+EVOH)/PP复合材料,其中PP为聚丙烯,EVOH为乙烯-乙烯醇其聚物.通过扫描电子显微镜观察、气体渗透实验、差示扫描量热仪分析以及力学性能测试研究了微层共挤出复合材料的形态结构及其对复合材料气体阻隔性能、力学性能以及结晶性能的影响.研究结果表明,通过微层共挤出技术,PP层和(PP+EVOH)层沿挤出方向交替排列,EVOH在PP基体中的的分散形态由零维球形变为一维纤维状,进而演变为二维片状.这些形态导致微层共挤出材料的氮气渗透系数和断裂伸长率较普通共混物分别下降了两个数量级和提高了27倍,并且显著影响其结晶行为.当层数超过64层后,由于PP层减薄,界面增多,EVOH不仅对(PP+EVOH)层中PP相存在结晶成核作用,而且对PP层也有结晶成核作用.     

Development of novel elastomeric blends derived from chlorinated nitrile rubber and chlorinated ethylene propylene diene rubber

Chlorinated nitrile rubber (Cl-NBR) has been blended with chlorinated ethylene propylene diene rubber (Cl-EPDM) in different ratios by a conventional mill mixing method. The effect of the blend ratio on processing characteristics, mechanical properties (such as tensile and tear strength, elongation at break, hardness, abrasion resistance, heat build-up and resilience), structure, morphology, glass transition temperature (Tg), thermal stability, flame retardancy, oil resistance, AC conductivity, dielectric properties and transport behavior of petrol, diesel and kerosene were investigated. The shift in absorption bands of blends studied from FTIR spectra, single Tg from DSC analysis and decrease in amorphous nature from XRD showed the molecular miscibility in Cl-NBR/Cl-EPDM blends. SEM images showed the uniform mixing of both Cl-NBR and Cl-EPDM in a 50/50 blend ratio. The TGA curves indicated the better thermal stability of the polymer blend. The elongation at break, heat build-up, resilience and hardness of the polymer blend decreases with an increase in Cl-NBR content in the blend whereas the flame and oil resistance were increased with increase in Cl-NBR content. Among the polymer blends, the maximum torque, tensile strength, tear and abrasion resistance was obtained for the 50/50 blend ratio because of the effective interfacial interactions between the blend components. AC conductivity and dielectric properties of polymer blend increased with increase in the ratio of Cl-NBR in the blend. Different transport properties such as diffusion, permeation and sorption coefficient were measured with respect to nature of solvent and different blend ratios. Temperature dependence of diffusion was used to estimate the activation parameters and the mechanism of transport found to be anomalous.     

Highly toughened poly(lactic acid) (PLA) prepared through melt blending with ethylene-co-vinyl acetate (EVA) copolymer and simultaneous addition of hydrophilic silica nanoparticles and block copolymer compatibilizer

In this study, a highly toughened PLA was prepared through physical melt-blending with EVA at the presence of hydrophilic nanosilica and SEBS-g-MA block copolymer compatibilizer. The effect of nanosilica and compatibilizer on the morphology, mechanical properties, and linear rheology of the PLA/EVA blends was also investigated. According to TEM images, nanosilica was selectively located in the PLA matrix while some were placed on the interface between the two polymers as was also predicted by thermodynamic and kinetic analysis. Upon the addition of nanoparticles, the interfacial adhesion between the phases was enhanced and the average droplet size decreased. Interestingly, incorporation of SEBS-g-MA induced morphological changes as the spherical EVA droplets turned into a cylindrical shape. DSC results indicated that blending with EVA copolymer resulted in the reduction of crystallization of PLA matrix; however, the crystallinity increased at the presence of nanoparticles up to 5 wt%. The addition of compatibilizer considerably hindered the crystallization of the PLA phase. PLA/EVA blend containing optimum levels of nanosilica exhibited considerably enhanced tensile toughness, elongation at break, and impact strength. On the other hand, the simultaneous addition of nanoparticles and SEBS-g-MA led to synergistic toughening effects and the compatibilized blend containing nanosilica exhibited excellent impact toughness. For instance, the elongation at break of the compatibilized PLA/EVA blend containing the optimal content of nanosilica was increased from 7% to 121% (compared to neat sample). The notched Izod impact strength was also increased from 5.1 to 65 kJ/m². Finally, the microstructure of the blends was assessed by rheological measurements.     

Thermal,mechanical, and morphological properties of soybean oil-based polyurethane/epoxy resin interpenetrating polymer networks (IPNs)

A series of interpenetrating polymer networks (IPNs) based on epoxy (EP) resin and polyurethane (PU) prepolymer derived from soybean oil-based polyols with different mass ratios were synthesized. The structure, thermal properties, damping properties, tensile properties, and morphology of soybean oil-based PU/EP IPNs were characterized by Fourier-transform infrared spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), universal test machine, and scanning electron microscopy (SEM). DSC and DMA results show that the glass transition temperature of the soybean oil-based PU/EP IPN decreases with the increase of PU prepolymer contents. Soybean oil-based PU/EP IPNs have better damping properties than that of the pure epoxy resin. The tensile strength and modulus of PU/EP IPNs decrease, while elongation at break increases with the increase of PU prepolymer contents. SEM observations reveal that phase separation appears in PU/EP IPNs with higher PU prepolymer contents.     

动态固化聚丙烯/环氧树脂共混物的研究

将动态硫化技术应用于热塑性树脂 热固性树脂体系 ,制备了动态固化聚丙烯 (PP) 环氧树脂共混物 .研究了动态固化PP 环氧树脂共混物中两组分的相容性、力学性能、热性能和动态力学性能 .实验结果表明 ,马来酸酐接枝的聚丙烯 (PP g MAH)作为PP和环氧树脂体系的增容剂 ,使分散相环氧树脂颗粒变细 ,增加了两组分的界面作用力 ,改善了共混物的力学性能 .与PP相比 ,动态固化PP 环氧树脂共混物具有较高的强度和模量 ,含 5 %环氧树脂的共混物拉伸强度和弯曲模量分别提高了 30 %和 5 0 % ,冲击强度增加了 15 % ,但断裂伸长率却明显降低 .继续增加环氧树脂的含量 ,共混物的拉伸强度和弯曲模量增加缓慢 ,冲击强度无明显变化 ,断裂伸长率进一步降低 .动态力学性能分析 (DMTA)表明动态固化PP 环氧树脂共混物是两相结构 ,具有较高的储能模量 (E′)     

Evaluation of the SEBS copolymer in the compatibility of PP/ABS blends through mechanical,thermal, thermomechanical properties,and morphology

Polypropylene (PP) blends with acrylonitrile-butadiene-styrene (ABS) were prepared using the styrene-ethylene-butylene-styrene copolymer (SEBS) as a compatibilizing agent. The blends were prepared in a co-rotational twin-screw extruder and injection molded. Torque rheometry, Izod impact strength, tensile strength, heat deflection temperature (HDT), differential scanning calorimetry, thermogravimetry, and scanning electron microscopy properties were investigated. The results showed that there was an increase in the torque of PA6/ABS blends with SEBS addition. The PP/ABS/SEBS (60/25/15%) blend showed significant improvement in impact strength, elongation at break, thermal stability, and HDT compared with neat PP. The elastic modulus and tensile strength have not been significantly reduced. The degree of crystallinity and the crystalline melting temperature increased, indicating a nucleating effect of ABS. The PP/ABS blends compatibilized with 12.5% and 15% SEBS presented morphology with well-distributed fine ABS particles with good interfacial adhesion. As a result, thermal stability has been improved over pure PP and the mechanical properties have been increased, especially impact strength. In general, the addition of the SEBS copolymer as the PP/ABS blend compatibilizer has the advantage of refining the blend's morphology, increasing its toughness and thermal stability, without jeopardizing other PP properties.     

Photocrosslinking of EVA/inorganic filler blends and characteristics of related properties

The blends of EVA filled with talc, calcium carbonate, and glass ball (GB) have been photocrosslinked by UV irradiation in the presence of benzophenone (BP) as a photoinitiator and triallyl isocyanurate (TAIC) as a crosslinker. The various factors affecting the crosslinking process and the related properties have been studied by gel determination, heat extension test, mechanical and thermal aging test, UV spectroscopy, and scanning electron microscopy. The results show that the EVA/talc, EVA/CaCO₃, and EVA/GB samples of 1 mm thickness filled with 25 phr inorganic filler can be photocrosslinked to gel content of above 70 wt% by 5 sec UV‐irradiation under optimum conditions, which is sufficient for some applications of EVA blend materials. The crosslinking rate and final gel content level are in the order of EVA/GB > EVA/talc > EVA/CaCO₃. The data from mechanical and thermal aging tests give evidence that the photocrosslinked EVA/talc, EVA/CaCO₃, and EVA/GB samples are of much better tensile strength and thermal aging properties than those of the unphotocrosslinked ones. Copyright © 2009 John Wiley & Sons, Ltd.     

高导热氮化硼/芳纶沉析复合薄膜的制备及性能

利用多巴胺(DA)的氧化自聚合特性, 对六方氮化硼(h-BN)进行表面修饰, 并以多巴胺改性后的氮化硼(h-BN@PDA)为导热填料, 对基体芳纶沉析纤维(AF)进行填充, 通过真空辅助抽滤法制备多巴胺改性氮化硼/芳纶沉析(h-BN@PDA/AF)复合薄膜, 并对其微观形貌、 表面官能团、 导热性能、 绝缘性能及力学性能进行研究. 结果表明, 聚多巴胺(PDA)包覆在h-BN表面, 并引入活性基团, 与AF纤维产生氢键, 改善了两者的界面结合, 显著提高了复合薄膜导热性能及绝缘性能. 当h-BN@PDA含量为70%时, h-BN@PDA/AF复合薄膜的导热系数为1.36 W/(m·K), 与纯芳纶沉析薄膜相比, 导热系数的增幅约为697.65%, 体积电阻率为5.96×10 ¹⁴ Ω·m, 拉伸模量高达287.19 MPa.     

Effect of Surface-modified Clay on the Thermal Stability and Insulation of Polyorganosiloxane Foam

Polyorganosiloxane foam(SIF) nanocomposites reinforced with vinyl-modified montmorillonite(Mt-V) and hydrox-yl-modified montmorillonite(Mt-OH) were prepared through cross-linking and foaming. The effects of modified Mt on the density, pore morphology, and thermal and compressive properties of the prepared polyorganosiloxane foams were investi-gated. The structure of the polyorganosiloxane foam was studied by solid-state nuclear magnetic resonance analysis. Clay dispersion in polyorganosiloxane nanocomposites and pore morphology were investigated by X-ray diffraction and scan-ning electron microscopy analyses. The thermal and mechanical properties of the prepared materials were also evaluated by differential scanning calorimeter, thermogravimetric analysis, thermal diffusivity and compressive strength. The results show that Mt-V exhibits improved cell structure, thermal insulation, and crush compressive than Mt-OH. The addition of modified Mt reduces the density, cell size, and thermal conductivity but increases the high-temperature resistance and com-pressive strength of the nanocomposite. The amount of the residues of SIF/Mt-OH nanocomposites increases by 9% com-pared with that of the pure SIF. Furthermore, SIF/Mt-V decreases the thermal conductivity to 0.014 W/mK and the cell size to 98 μm. Those properties give the material potential application value in the aerospace and construction industry.     

Effect of Electron Beam Irradiation and Ethylene Vinyl Acetate Copolymer on the Properties of NBR/HDPE Blends

The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M₅₀), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E _b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.     

Effect of Electron Beam Irradiation on the Properties of High Styrene Rubber/Styrene Butadiene Rubber Blends

High styrene rubber (HSR)/styrene butadiene rubber (SBR) blends at different ratios were exposed to various doses of electron beam irradiation. The effect of irradiation dose and blend ratios on the mechanical properties and shape memory characteristics in terms of strain fixation) rate (R_f) and strain recovery rate (R_r) was investigated. The results revealed that rich styrene blends displayed higher tensile strength and hardness than low styrene content blends at all irradiation doses. However, elongation at break, and toughness were lower for rich styrene content. Also, it was observed that for most specimens, the tensile strength, elongation at break and hardness increases up to100 kGy. Increasing irradiation doses resulted in slight deterioration in some mechanical properties only for low styrene content at150 kGy. According to the normalized tensile stress at 25% elongation, it was found that the contribution of irradiation in enhancing the mechanical properties is higher for rich butadiene blends. On the other hand, it was observed that rich styrene content blends possess higher R_f and R_r at all the irradiation doses and stretching temperatures. However, the increase of irradiation dose decreases R_f values; the extent of this decrease depends on the blend ratios. Conversely, for all blends, R_r were increased by increasing irradiation dose and styrene content ratios.     

Synthesis and characterization of polyaniline filled PU/PMMA interpenetrating polymer networks

A series of conducting interpenetrating polymer networks (IPNs), are prepared by sequential polymerization of castor oil based polyurethane (PU) with poly(methyl methacrylate) (PMMA) and polyaniline doped with camphor sulphonic acid (PAni)_CSA. The effect of different amount of PAni (varies from 2.5-12.5%) on the properties of PU/PMMA (50/50) IPNs such as electrical properties like conductivity, dielectric constant and dissipation factor; mechanical properties like tensile strength and percentage elongation at break have been reported. (PAni)_CSA filled IPNs shows improved tensile strength than the unfilled IPN system. The thermal stability and surface morphology of unfilled and (PAni)_CSA filled PU/PMMA (50/50) IPN sheets were investigated using a thermogravimetric analyzer (TGA) and a scanning electron microscope (SEM). TGA thermograms of (PAni)_CSA filled PU/PMMA (50/50) IPNs show a three-step thermal degradation process. SEM micrograms of filled PU/PMMA IPN system shows spherulitic structure at higher concentration of (PAni)_CSA.     

Method for Simultaneously Improving the Thermal Stability and Mechanical Properties of Poly(lactic acid): Effect of High-Energy Electrons on the Morphological, Mechanical, and Thermal Properties of PLA/MMT Nanocomposites

Nanocomposites derived from poly(lactic acid) (PLA) and organically modified montmorillonite (oMMT) have been cross-linked by high-energy electrons in the presence of triallyl cyanurate (TAC). The morphology of untreated and cross-linked PLA/MMT nanocomposites was characterized by wide-angle X-ray scattering (WAXS) and transmission electron microscopy (TEM). This treatment can improve both the thermal stability and the glass-transition temperatures of the PLA nanocomposites (e.g., PLA-MMT-TAC 30kGy, 50kGy, and 70kGy) because of the formation of cross-linking structures in the nanocomposites that will considerably reduce the mobility of polymers. Interestingly, at relatively low irradiation doses (e.g., 30 and 50 kGy) a good balance between tensile strength and elongation at break for the PLA nanocomposites could be achieved. These mechanical properties are superior to those of pure PLA. Therefore, combining nanotechnology and electron beam cross-linking is a promising new method of simultaneously improving the mechanical properties (toughness and tensile strength) and thermal stability of PLA.     

高耐热、低介电常数含氟聚酰亚胺材料的合成与性能研究

合成了一系列新型含氟耐高温、低介电常数聚酰亚胺 (PI)材料 ,并对其进行了热性能、电性能等方面的测试 .结果表明 ,这类分子结构中含吡啶环单元的材料可保持PI固有的耐热性能 ,其在氮气下的热分解温度为 5 4 5～ 6 0 1℃ ;而侧链的双三氟甲基取代结构一方面使分子具有较高的氟含量 ,另一方面增大了分子的自由体积 ,这两方面的共同作用使得这类材料具有优良的介电性能 ,其介电常数为 2 86～ 2 91;击穿电压为15 0 4～ 197 3kV mm .