双单体原位接枝插层法制备聚丙烯纳米复合材料的研究Ⅰ.制备、表征及力学性能的研究

用有机插层剂处理蒙脱土原土 ,制得有机蒙脱土 (O MMT) .采用双单体 (马来酸酐和苯乙烯 )原位接枝插层法 ,制备了聚丙烯 蒙脱土纳米复合材料母料 .将母料与聚丙烯基体在双螺杆上共混挤出 ,制得聚丙烯 蒙脱土纳米复合材料 (PP Montmorillonetenanocomposites,PMNC) .这是制备聚合物纳米复合材料的一种新方法 .通过X 射线衍射测试 (XRD)表明 ,有机蒙脱土片层 0 0 1面间距从原土的 1 4 9nm扩大到 2 96nm ,复合材料中蒙脱土片层 0 0 1面间距由有机蒙脱土的 2 96nm扩大到 4 0nm .力学性能测试表明 ,复合材料的力学性能明显优于PP基体 ,在提高材料拉伸强度的同时 ,缺口冲击强度也得到很大的提高 .用扫描电镜 (SEM)对材料的冲击断面形貌进行了研究 ,并从理论上分析了断裂机理 .随着蒙脱土含量的增加 ,冲击断裂形式逐渐从脆性断裂变成韧性断裂     

聚苯胺/离子液体/蒙脱土纳米复合材料的制备及其导电性能研究

采用1-羧甲基-3-甲基咪唑氯化盐离子液体对钠化蒙脱土进行插层改性,然后用苯胺的盐酸溶液进行二次插层,以过硫酸铵为氧化剂,盐酸溶液为掺杂剂,使进入离子液体/蒙脱土(CMMIm/MMT)层间的苯胺(An)发生氧化聚合反应,制备了一种具有良好导电性的聚苯胺/离子液体/蒙脱土复合材料(PANI/CMMIm/MMT).用红外光谱、X-射线衍射,热重分析和DSC对样品进行了表征.结果表明当离子液体/蒙脱土用量为7.5%、盐酸浓度为1mol/L、过硫酸铵与苯胺的摩尔比为1∶1、0℃下反应6h时制备的PANI/CMMIm/MMT纳米复合材料电导率最高,达到了0.3S/cm,是相同条件下聚苯胺/钠化蒙脱土纳米复合材料电导率的2.5倍,聚苯胺的7.5倍.     

聚萘并噁嗪/蒙脱土纳米复合材料的制备与表征

用原位插层反应法地制备了聚萘并嗪 蒙脱土纳米复合材料 .采用X ray衍射 (XRD)及透射电镜(TEM)研究复合材料中蒙脱土硅酸盐片层间距 ,发现硅酸盐片层间距由 1 2 6nm扩增至 5 88nm以上 .同时研究了该复合材料的耐热性 ,并探讨了复合材料的结晶行为     

sPS/PA6/蒙脱土纳米复合材料的制备与性能

讨论了间规聚苯乙烯 (sPS) 尼龙 6(PA6) 磺化间规聚苯乙烯 (SsPS H) 蒙脱土纳米复合材料的制备技术和新材料的结构与性能特征 .蒙脱土经层间改性处理后 (MTN) ,可分别将SsPS H和aPS(无规聚苯乙烯 )插入其纳米层间 ,制备出插层型纳米复合物MTN SsPS和MTN aPS .在sPS/PA6/SsPS H三组分共混体系中加入MTN SsPS或MTN aPS ,进行四组分熔融共混即可制备出sPS/PA6/SsPS H/蒙脱土纳米复合材料 .TEM测定证实了蒙脱土在基体中的层厚分布约为 5 0nm .此外 ,采用DSC、DMA、XRD及力学性能测试仪等现代分析方法对sPS/PA6/SsPS H/蒙脱土纳米复合材料的结构与性能进行了详细研究 .研究结果表明这种纳米复合材料具有优良的综合性能     

聚氨酯弹性体/蒙脱土纳米复合材料的合成与性能

采用聚氨酯本体预聚法 ,利用原位插层聚合合成了聚氨酯 蒙脱土纳米复合材料 .通过X 射线衍射(XRD)和Molau实验研究了蒙脱土在复合材料中的分散情况 .红外分析 (IR)表明随着蒙脱土含量的增加 ,复合材料羰基氢键减少 .动态力学分析 (DMA)以及差热分析 (DSC)结果说明随着蒙脱土含量的增加 ,材料的玻璃化温度降低 .聚氨酯纳米复合材料的拉伸强度和断裂伸长率同时提高 ,表现出较好的力学性能 .     

三聚苯撑乙烯/蒙脱土发光光谱的时间依赖性

用原位插层法制备了插层型的三聚苯撑乙烯/蒙脱土(TPV/MMT)纳米复合材料. 研究了新制备及在室温储存180天后的TPV/MMT纳米复合材料的荧光光谱及蒙脱土层间距的变化情况. 荧光光谱分析表明, 储存180天后, TPV/MMT纳米复合材料的最大发射峰由494 nm蓝移到438 nm, 半峰宽由77 nm增加到104 nm. X射线衍射结果表明, 与新制备的复合材料相比, 蒙脱土的层间距由1.52 nm减小到1.22 nm. 红外光谱分析表明, 室温储存180天后的三聚苯撑乙烯苯环的某些特征峰由1598 和1554 cm-1分别红移到1506和1462 cm-1. 依据相关实验和理论数据探讨了储存180 天前后TPV在蒙脱土中聚集态结构的变化方式.     

尼龙6/蒙脱土纳米复合材料非等温结晶动力学和透明性研究

将有机化的蒙脱土与尼龙6(PA6)在Haake共混机中共混,制备出尼龙6/蒙脱土纳米复合材料(PA6N);对尼龙6/蒙脱土纳米复合材料和纯尼龙6分别进行差示扫描量热法非等温结晶试验,以了解蒙脱土在尼龙6/蒙脱土纳米复合材料中的成核作用、扩大尼龙6在包装领域的应用范围.与此同时,采用偏光显微镜测定了样品的结晶形态;采用紫...     

高抗冲聚苯乙烯/粘土纳米复合材料的制备、热稳定性及流变性能

用双螺杆挤出共混法制备了高抗冲聚苯乙烯 (HIPS) 有机蒙脱土 (Org MMT)插层纳米复合材料以及HIPS 无机蒙脱土 (MMT)常规复合材料 .分别用TGA和毛细管流变仪研究了它们的热性能与流变性能 ,并比较了两种结构材料的性能差异 .结果表明 ,纳米复合材料比纯HIPS和常规的复合材料具有更好的热稳定性和流动性 ,前者具有更强的剪切变稀行为 .此外 ,当蒙脱土达到纳米级分散时 ,复合材料的表面也变得更加平整光滑 .     

聚氨酯弹性体/蒙脱土纳米复合材料的合成、结构与性能

采用插层聚合法合成了综合力学性能优异的聚氨酯 蒙脱土纳米复合材料 .X 射线衍射结果表明 ,蒙脱土以平均层间距不小于 4 5nm的宽分布分散在聚氨酯基体中 .加入 7 5wt%左右的蒙脱土 ,复合材料的拉伸强度高于纯PU基体的 2倍 ,断裂伸长率则高于纯PU基体的 4倍以上 .TGA分析表明 ,聚氨酯 蒙脱土纳米复合材料的热稳定性略有提高     

聚苯乙烯/蒙脱土纳米复合材料中的剪切诱导有序结构(Ⅰ)——广角X射线衍射与透射电镜研究

聚合物/层状硅酸盐(PLS)纳米复合材料是近10余年来迅速发展起来的的交叉学科.由于其具有常规复合材料所没有的结构、形态以及较常规聚合物基复合材料更优异的性能等而引起人们的广泛关注[1].以往文献主要报道PLS纳米复合材料的制备与性能表征,如尼龙-6/蒙脱土[2]、PET/蒙脱土[3]和硅橡胶/蒙脱土[4]等.对于熔融加工过程中粘土片层及高分子的取向和结构研究很少.Kojima等[5]发现并研究了尼龙-6/蒙脱土纳米复合材料中的熔融剪切诱导取向结构,其X射线衍射与透射电镜(TEM)结果均表明,粘土片层沿熔体流动方向平行取向,但片层间距不等,因此为一平行取向但无序的结构.对于PLS纳米复合材料中的剪切诱导有序结构尚未见报道.     

A new approach of enhancing the shear stress of electrorheological fluids of montmorillonite nanocomposite by emulsion intercalation of poly-N-methaniline

Poly-N-methaniline/montmorillonite (PNMA-MMT) nanocomposite particles with high dielectric constant as well as suitable conductivity were synthesized by an emulsion intercalation method and characterized by FT-IR, XRD, and TEM spectrometry, respectively. The electrorheological (ER) properties of the suspensions of PNMA-MMT particles in silicone oil (20 wt%) were investigated under DC electric fields. It was found that the shear stress of poly-N-methaniline/montmorillonite electrorheological fluid (ERF) is 6.0 kPa in 3 kV/mm (74.5 s(-1)), which is 3.6 times that of electrorheological fluid at zero field, and also much higher than that of pure poly-N-methaniline (PNMA) and montmorillonite (MMT). In the range of 10-90 degrees C, the shear stress changes slightly with the temperature. The sedimentation ratio of PNMA-MMT ERF was about 97% after 60 days. Furthermore, the dielectric constant of PNMA-MMT nanocomposite was increased 3.74 times that of PNMA and 1.99 times that of MMT at 1000 Hz, the dielectric loss tangent also increased about 1.58 times that of PNMA. It is apparent that the notable ER effect of PNMA-MMT ER fluid was attributed to the prominent dielectric property of the poly-N-methaniline/montmorillonite nanocomposite particles.     

蒙脱土/二氧化钛复合颗粒电流变液材料的制备及其性能

利用溶胶-凝胶法制备了一种新型的蒙脱土/二氧化钛(MMT/TiO_2)复合电流变 颗粒材料，FT-IR，XRD，SEM分析表明TiO_2以纳米晶的形态包覆于蒙脱土表面。电 流变性能测试表明，MMT/TiO_2复合颗粒的电流变效应比纯蒙脱土电流变液有显著 提高，当颗粒体积分数为25%，直流电场强度为3kV/mm时，TiO_2质量分数为22.7% 的MMT/TiO_2复合颗粒电流变液的静态屈服应力达8.3kPa，此值约为纯蒙脱土电流 变液的4倍。同时发现TiO_2包覆量对电流变效应有重要影响。     

Preparation of montmorillonite/titania nanocomposite and enhanced electrorheological activity

We prepared a new type of electrorheological particle composed of TiO2 nanocrystallites-coated montmorillonite (MMT/TiO2) nanocomposite by the sol-gel technique. The characterizations including TGA, XRD, TEM, SEM, EDS, and FTIR showed that TiO2 was deposited on the surface of the MMT flakes with anatase nanocrystallite. An obviously enhanced ER effect was found in the MMT/TiO2 nanocomposites based ER fluids compared with pure MMT and TiO2. Furthermore, the temperature and sedimentation stabilities of the MMT/TiO2 ER fluids had also been improved greatly. Interestingly, the content of TiO2 was demonstrated to have an important influence on the ER effect. When the content of TiO2 was about 20 wt%, the ER effect of MMT/TiO2 ER fluid reached its maximum, which was about 5 times that of pure MMT ER fluid and 27 times that of pure TiO2 ER fluid. Based on dielectric analysis, the significant ER enhancement by formation nanocrystallites-coated montmorillonite was attributed to the enhanced interfacial polarization in this nanocomposite particle due to the effective limitation of the long-range drift of active ions in montmorillonite particles.     

The influence of high dielectric constant core on the activity of core-shell structure electrorheological fluid

The core-shell structural dielectric particles are applied widely in the electrorheological (ER) fluids. The properties of the dielectric core are critical factors influencing their ER activity. In this paper, we successfully synthesized two kinds of core-shell hydroxyl titanium oxalate (TOC) particles with SiO(2) and TiO(2) as core, respectively. The obtained core-shell structural SiO(2)-TOC and TiO(2)-TOC particles were well-dispersed spherical nanoparticles with ideal morphology and a narrow size distribution. Under DC electric fields, the TiO(2)-TOC ER fluid showed notable ER activity with a yield stress of about 96 kPa (at 4 kV/mm), which is 3 times of that SiO(2)-TOC ER fluid and outclassed the yield stress of the TOC ER fluid. The dielectric spectra indicated that the higher dielectric constant of TiO(2) core induces the stronger interaction between the neighboring particles, which contribute to the enhancement of ER activity.     

辐照法制备PVAc/蒙脱土纳米复合材料及其表征

蒙脱土有机化后 ,片层结构间距离增大 ,对有机物的亲和性有所增强 .采用VAc单体渗入有机化蒙脱土层间 .经γ 射线辐照引发原位插层聚合 ,使蒙脱土片层结构发生剥离 ,形成无机 有机纳米复合材料 .并用X衍射、红外光谱、扫描电镜以及透射电镜等现代测试手段对复合材料进行了表征     

The influence of intercalation rate and degree of substitution on the electrorheological activity of a novel ternary intercalated nanocomposite

Kaolinite/dimethylsulfoxide (DMSO)/carboxymethyl starch (CMS) ternary nanocomposites were prepared according to the combination of intercalation and solution reaction. The results show that the intercalation rate (IR) of kaolinite in the ternary composite is adjusted by changing the mass rate, and the basal spacing of kaolinite was swelled from 0.715 to 1.120 nm. At the suitable component ratio of ternary nanocomposite, the optimum electrorheological (ER) effect can be attained. It is apparent that the notable ER effect of ternary ER fluid was attributed to the prominent dielectric property of the ternary nanocomposite electrorheological fluids (ERF), which is closely associated with the IR. With the increase of degree of substitution, the ER effect of ternary composite ERF is enhanced.     

Self‐Assembled Poly(N‐methylaniline)–Lignosulfonate Spheres: From Silver‐Ion Adsorbent to Antimicrobial Material

Self‐assembled poly(N‐methylaniline)–lignosulfonate (PNMA–LS) composite spheres with reactive silver‐ion adsorbability were prepared from N‐methylaniline by using lignosulfonate (LS) as a dispersant. The results show that the PNMA–LS composite consisted of spheres with good size distribution and an average diameter of 1.03–1.27 μm, and the spheres were assembled by their final nanofibers with an average diameter of 19–34 nm. The PNMA–LS composite spheres exhibit excellent silver‐ion adsorption; the maximum adsorption capacity of silver ions is up to 2.16 g g^?1 at an adsorption temperature of 308 K. TEM and wide‐angle X‐ray results of the PNMA–LS composite spheres after absorption of silver ions show that silver ions are reduced to silver nanoparticles with a mean diameter of about 11.2 nm through a redox reaction between the PNMA–LS composite and the silver ions. The main adsorption mechanism between the PNMA–LS composite and the silver ions is chelation and redox adsorption. In particular, a ternary PNMA–LS–Ag composite achieved by using the reducing reaction between PNMA–LS composite spheres and silver ions can be used as an antibacterial material with high bactericidal rate of 99.95 and 99.99 % for Escherichia coli and Staphylococcus aureus cells, respectively.     

Electrorheological characterization of polyaniline-coated poly(methyl methacrylate) suspensions

Surface-conductive particles consisting of a poly(methyl methacrylate) (PMMA) core and a polyaniline (PA)-coated shell were synthesized and adopted as suspended particles for electrorheological (ER) fluids. The PA-PMMA composite particles synthesized were monodisperse and spherical in shape. The PA-PMMA suspensions in silicone oil showed typical ER characteristics under an applied electric field. The PA-PMMA composite particles possess a higher dielectric constant and conductivity than the pure PA particle, within an acceptable conductivity range for ER fluids, but the PA-based ER fluid showed larger shear-stress enhancement than the PA-PMMA-based systems. This phenomena can be explained by the interfacial polarizability of PA-based ER fluids, which is the difference between the ER fluid's dielectric constant and loss factor - this polarizability was higher than that of PA-PMMA-based ER fluids, as shown by the dielectric spectrum of each fluid. The insulating PMMA core suppressed the interfacial polarization in ER fluids, resulting in reduced interaction among particles under an imposed electric field.     

Electrorheological property and microstructure of acetamide-modified TiO<Subscript>2</Subscript> nanoparticles

A sol–gel method has been proposed to prepare uniform TiO₂ nanoparticles whose average size is about 30 nm. The prepared nanometer TiO₂ particles are modified by acetamide via different self-assembled processes. X-ray diffraction analyses, scanning electron microscopy, and Fourier transform infrared spectrometry are used to determine the structure of the nanoparticles. The results indicate that the different synthesis processes do not change the morphology of the TiO₂/acetamide nanoparticles; nevertheless, they affect the interaction between amide and acetamide. The electrorheological (ER) activity is studied by shear stress under DC electric field. The acetamide-modified TiO₂ ER fluid shows notable ER activity with shear stress about 45 kPa (at 5 kV/mm), which outclasses the shear stress (2 kPa) of unmodified TiO₂ ER fluid. It is also found that the ER effect is very sensitive to the interaction of molecules on TiO₂ particles. The chemical bond between core and shell can enhance the ER activity of the sample.     

Synthesis and characterization of organosoluble,thermoplastic elastomer/clay nanocomposites

We synthesized organosoluble, thermoplastic elastomer/clay nanocomposites by making a jelly like solution of ethylene vinyl acetate containing 28% vinyl acetate (EVA‐28) and blending it with organomodified montmorillonite. Sodium montmorillonite (Na⁺‐MMT) was made organophilic by the intercalation of dodecyl ammonium ions. X‐ray diffraction patterns of Na⁺‐MMT and its corresponding organomodified dodecyl ammonium ion intercalated montmorillonite (12Me‐MMT) showed an increase in the interlayer spacing from 11.94 to 15.78 Å. However, X‐ray diffraction patterns of the thermoplastic elastomer and its hybrids with organomodified clay contents up to 6 wt % exhibited the disappearance of basal reflection peaks within an angle range of 3–10°, supporting the formation of a delaminated configuration. A hybrid containing 8 wt % 12Me‐MMT revealed a small hump within an angle range of 5–6° because of the aggregation of silicate layers in the EVA‐28 matrix. A transmission electron microscopy image of the same hybrid showed 3–5‐nm 12Me‐MMT particles dispersed in the thermoplastic elastomer matrix; that is, it led to the formation of nanocomposites or molecular‐level composites with a delaminated configuration. The formation of nanocomposites was reflected through the unexpected improvement of thermal and mechanical properties; for example, the tensile strength of a nanocomposite containing only 4 wt % organophilic clay was doubled in comparison with that of pure EVA‐28, and the thermal stability of the same nanocomposite was higher by about 34 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2065–2072, 2002