聚电解质PDDA/PSS层层自组装膜的渗透汽化性能

采用聚电解质层层自组装(LbL)技术, 在不同盐浓度下制备了聚(二烯丙基二甲基氯化铵)/聚苯乙烯磺酸钠(PDDA/PSS) 多层自组装膜, 并用于渗透汽化性能的研究. 重点考察了组装溶液中NaCl的浓度、组装层数及操作温度对自组装膜的异丙醇脱水性能的影响. 同时, 用扫描电镜观测了不同条件下制备膜的表面形貌. 结果表明, 在高NaCl含量的聚电解质溶液中只需组装几个双层的LbL膜, 即能获得较高的分离因子和较大的通量, 并解释了该LbL膜呈现反“trade-off”现象的原因.     

一种偶氮聚电解质在不同pH值条件下的静电逐层自组装研究

研究了一种光响应偶氮聚电解质(PEAPE)在不同pH值条件下的自组装,重点讨论了pH值对静电逐层自组装以及对光响应性能的影响.研究表明,在所研究的pH范围内,pH值越低,越有利于生成吸光度高的自组装膜,对应的自组装膜厚度也越大.红外光谱分析表明,偶氮聚电解质在不同pH溶液中存在不同的电离情况.pH值越低,用于自组装的溶液中的聚合物链上的电荷数越少,链构象越卷曲.解释了不同pH值条件下自组装膜吸光度和厚度差别的原因.     

银/聚电解质复合纳滤膜的制备及表征

利用层层自组装技术(LbL),采用原位还原方法在聚醚砜(PES)基膜上制备了银/聚电解质复合纳滤膜.SEM分析表明:膜表面结构致密,Ag粒子在复合膜中分布均匀,粒径100～200 nm,UV-vis图谱证明膜中粒子为Ag粒子,所得银/聚电解质纳滤膜呈现出优异的抗菌性能.[PSS/PDADMAC]3[PAS/PAH-Ag]3PSS膜对负二价离子显示出较高的截留性能,达到93%.     

旋光聚[乙烯-alt-R-N-(1-苯乙基)马来酰胺酸]的合成及静电自组装

以聚(乙烯-alt-马来酸酐)为原料,通过与R-(+)-α-苯乙胺的酰胺化反应,合成了一种新型的旋光聚电解质聚[乙烯-alt-R-N-(1-苯乙基)马来酰胺酸],利用红外吸收光谱、紫外吸收光谱、核磁共振氢谱和旋光度数据对其结构进行表征.聚[乙烯-alt-R-N-(1-苯乙基)马来酰胺酸]与聚二甲基二烯丙基氯化铵(PDDA)逐层静电自组装过程的紫外跟踪测试结果表明,带相反电荷的聚电解质间能够形成稳定增长的自组装膜,多层膜组装量随双层数指数增大.     

冷冻干燥法制备天然高分子复合聚电解质纳米纤维

将壳聚糖(CS)溶液和透明质酸钠(SH)溶液共混,制备成CS-SH复合聚电解质溶液,并对溶液中所形成的胶粒进行了粒径分布和ZETA电位表征。用冷冻干燥法除去溶剂,制备了CS-SH复合聚电解质纳米纤维膜。用FT-IR对其结构进行分析,并用SEM对其形貌进行了表征。并将复合聚电解质纳米纤维膜作为疏水性药物紫杉醇(PTX)的载药体系,研究了其药物释放行为。结果表明,PTX在该载体中的释放较为平缓,这可以延长药物的有效时间,降低给药次数,增强治疗效果,降低药物的毒副作用。     

高分子化8-羟基喹啉锂的合成与静电自组装研究

设计合成了甲基丙烯酸二甲氨基乙酯(DM)含量为9.69%的丙烯酸甲酯共聚物(CPA),将制得的5-氯甲基-8-羟基喹啉(CHQ)挂接到CPA上,得到季铵型高分子化8-羟基喹啉(CPA-HQ)后,与金属离子Li+配位得到CPA-HQ-Li.化合物结构通过红外、紫外和荧光光谱等表征.多层超薄膜用CPA-HQ-Li和聚阴离子电解质(全氟磺酸)通过静电自组装制得.自组装膜的紫外和荧光相对于溶液(溶剂为四氢呋喃)发生了红移,膜的紫外吸收强度随组装膜层数增加线性增大,荧光强度随膜层数增加线性递减.高分子化8-羟基喹啉锂溶液和自组装膜的紫外和荧光光谱与文献报道一致.实验结果表明这种材料可用于有机电致发光器件(OLEDs)的制备.     

胶束增强型聚电解质微胶囊的制备

采用杂化碳酸钙微球作为模板, 利用LbL技术, 选择聚苯乙烯磺酸钠(PSS), 烯丙基胺的盐酸盐(PAH)和二烯丙基二甲基胺盐酸盐(PADA)聚电解质, 分别组装了PAH/PSS(弱/强)聚电解质胶囊和PADA/PSS(强/强)聚电解质微胶囊. 除去模板后得到了球形良好、分散均匀的聚电解质微胶囊. 研究结果表明, 利用杂化碳酸钙微球作为聚电解质微胶囊的模板, 得到的微胶囊的囊壁厚而致密, 同时, 由于组装采用的聚电解质的种类不同, 囊壁的微观形貌有较大差异.     

间位聚亚吡啶基亚乙炔基共轭聚电解质的合成与溶液光物理性质

合成了单体1,4-双(3-磺酰化丙氧基)-2,5-二碘苯与2,6-二乙炔基吡啶,利用Heck-Sonogashira偶联反应制备了间位聚亚吡啶基亚乙炔基共轭聚电解质m-PPYPE-SO3Na,对单体以及聚合物进行了红外光谱与核磁氢谱表征.测试了该共轭聚电解质m-PPYPE-SO3Na的紫外-可见吸收光谱与荧光发射光谱.研究了该共轭聚电解质的溶液光物理性质,发现该聚电解质具有荧光发射的溶剂依赖性以及浓度依赖性,在水溶液中存在聚集.在聚合物溶液浓度为1×10-6mol/L左右时,聚集发射基本消失,说明此时在溶液中聚合物的聚集程度已经比较低.该聚电解质在水溶液中与表面活性剂之间存在一定的相互作用,加入非离子型高分子表面活性剂聚乙烯吡咯烷酮(PVP)的聚合物水溶液荧光显著增强,表明该表面活性剂破坏聚电解质的聚集.该共轭聚电解质的溶液光物理性质表明其具有成为水溶性荧光探针的应用潜力.     

由聚电解质自组装多层膜制备微孔薄膜

带有相反电荷的聚电解质通过静电作用交替沉积可以得到自组装多层膜,由于这种技术可操作性强,用途广泛,近十几年来已有了大量的研究．聚电解质多层膜在一定条件下可以形成纳米孔和微米孔．Fu等研究了聚丙烯酸和聚乙烯基吡啶组成的氢键自组装多层膜在碱溶液中溶去其中的聚丙烯酸后,剩下的聚乙烯基吡啶重构形成微孔薄膜．Mendelsohn等发现将聚丙烯酸和聚烯丙基胺自组装而成的多层膜浸入pH=2．4左右的溶液中可制备微孔薄膜．但这些方法并不能使强聚电解质多层膜形成多孔结构。     

静电组装金纳米粒子制备局域表面等离子体共振传感膜

采用聚电解质自组装技术制备局域表面等离子体共振(LSPR)传感膜的方法, 在玻璃基片上依次沉积聚电解质PDDA, PSS和PVTC, 并通过静电吸附构建胶体金纳米粒子自组装膜形成LSPR传感膜. 利用扫描电镜对LSPR传感膜表面形貌以及膜中金纳米粒子的粒径进行了表征, 同时通过紫外-可见消光光谱对其灵敏度和渗透深度等重要参数进行检测. 研究结果表明, 所制备的LSPR传感膜粒子分布均匀、单分散性好、稳定性高、重现性好; 消光峰位对样品溶液折射率的检测灵敏度为71 nm/RIU, 相应的峰强检测灵敏度为0.21 AU/RIU, 对表面吸附层的渗透深度约为16 nm.     

Fabrication of free-standing multilayer films by using pH-responsive microgels as sacrificial layers

A facile way to prepare free-standing polyelectrolyte multilayer films of poly(sodium 4-styrenesulfonate)(PSS)/poly(diallyldimethylammonium)(PDDA) was developed by applying a new pH-dependent sacrificial system based on cross-linked poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA) microgels. The tertiary amine groups of PDMAEMA microgels can be protonated in acidic environment, and the protonated microgels were deposited by layer-by-layer (LbL) technique with PSS. PSS/PDDA multilayer films were constructed on the top of the PSS/microgels sacrificial layers. The LbL assembly process was investigated by UV–vis spectroscopy. Further study shows that the free-standing PSS/PDDA multilayer films can be obtained within 3 min by treating the as-prepared films in alkali aqueous solution with a pH of 12.0. The pH-triggered exfoliation of PSS/PDDA multilayer films provides a simple and facile way to prepare LbL assembled free-standing multilayer films.     

聚电解质PSS/PDDA分子沉积膜表面性能研究

PSS PDDAMD膜紫外 可见吸光度与层数呈线性关系 ,其延长线基本为零证实了是一单分子层层状沉积过程 ;利用接触角测量仪跟踪MD膜沉积过程 ,其结果表明 ,层数较少时PSS PDDAMD膜表面润湿性呈“奇 偶”性规律变化 ,层数较多时规律性不明显 ,这说明聚电解质MD膜结构缺陷随着层数的增加有增大趋势 ;通过对原子力显微镜 (AFM)测定结果的分析 ,进一步证实了多层PSS PDDAMD膜存在结构缺陷 .     

静电层层自组装制备聚苯乙烯微球(核)/MCM-41纳米粒子(壳)阶层结构复合微粒

采用聚苯乙烯磺酸钠(PSS)和聚二烯丙基二甲基氯化铵(PDDA)两种聚电解质, 通过静电层层自组装成功地将MCM-41介孔二氧化硅纳米粒子包覆到聚苯乙烯(PS)微球表面. 实验结果表明, 当以尺寸为1.4 μm的PS微球为核时, 包覆了两个聚电解质双层(PDDA/PSS)2的PS(PDDA/PSS)2(PDDA/MCM-41)复合结构微粒与包覆了一个聚电解质双层(PDDA/PSS)的PS(PDDA/PSS)(PDDA/MCM-41)复合结构微粒相比, 复合结构微粒之间的交联程度降低, 但是MCM-41纳米粒子在聚苯乙烯微球表面的包覆都比较松散, 且产物中存在大量杂质. 而当以尺寸为5 μm的聚苯乙烯微球为核时, MCM-41纳米粒子紧密地包覆在聚苯乙烯微球表面, 复合结构微粒之间只有少量桥连物, 且产物中杂质很少.     

Colloid stability of sodium dihexadecyl phosphate/poly(diallyldimethylammonium chloride) decorated latex

The colloid stability of supramolecular assemblies composed of the synthetic anionic lipid sodium dihexadecyl phosphate (DHP) on cationic poly(diallyldimethylammonium chloride) (PDDA) supported on polystyrene sulfate (PSS) microspheres was evaluated via turbidimetry kinetics, dynamic light scattering for particle sizing, zeta-potential analysis, and determination of DHP adsorption on PDDA-covered particles. At 0.05 g/L PDDA and 5 x 10(9) PSS particles/mL, PDDA did not induce significant particle flocculation and a vast majority of PDDA covered single particles were present in the dispersion so that this was the condition chosen for determining DHP concentration (C) effects on particle size and zeta-potentials. At 0.8 mM DHP, charge neutralization, maximal size, and visible precipitation indicated extensive flocculation and minimal colloid stability for the DHP/PDDA/PSS assembly. At 0.05 g L(-1) PDDA, isotherms of high affinity for DHP adsorption on PDDA-covered particles presented a plateau at a limiting adsorption of 135 x 10(19) DHP molecules adsorbed per square meter PSS which was well above bilayer deposition on a smooth particle surface. The polyelectrolyte layer on hydrophobic particles was swelled and fluffy yielding ca. 6 +/- 1.5 nm hydrodynamic thickness. Maximal and massive adsorption of DHP lipid onto this layer produced polydisperse DHP/PDDA/PSS colloidal particles with low colloid stability and which, at best, remained aggregated as doublets over a range of large lipid concentrations so that it was not possible to evaluate the mean total thickness for the deposited film. The assembly anionic lipid/cationic PDDA layer/polymeric particle was relatively stable as particle doublets only well above charge neutralization of the polyelectrolyte by the anionic lipid, at relatively large lipid concentrations (above 1 mM DHP) with charge neutralization leading to extensive particle aggregation.     

PET/PC共混体系的酯交换反应对其高压结晶行为的影响

利用转矩流变仪、DSC、SEM及WAXD等表征手段研究了PET/PC共混体系的酯交换反应对其高压结晶行为的影响.SEM观察表明,PET和PC熔混时的酯交换反应有利于PET/PC体系在高压结晶时生成厚度较大的伸直链晶体,且可以促进其高压下酯交换反应的发生.楔形伸直链晶体和弯曲伸直链晶体的存在证明链滑移扩散和酯交换反应两种机制对体系中聚酯伸直链晶体的增厚有贡献.拟合分峰法和War-ren-Averbach傅里叶分析法的计算结果表明,随PET/PC体系熔混时酯交换反应程度的增加,高压结晶共混物的结晶度降低,PET的平均微晶尺寸增大,点阵畸变平均值则减小,而微晶尺寸分布变宽.提出了在共聚物组分都具备结晶能力时,结晶诱导化学反应和化学反应诱导结晶两种过程在一定条件下可同时发生的观点.     

胶体颗粒在聚电解质多层膜表面的可控组装

利用原子力显微镜和扫描电子显微镜研究了磺化聚苯乙烯胶体颗粒在由聚二甲基二烯丙基氯化铵和聚苯乙烯磺酸钠层状自组装而成的多层膜表面的组装.该组装受表面性质影响,通过对多层膜的最外层的组装条件或利用盐溶液对多层膜进行后处理可以控制胶体颗粒在膜表面的组装密度.     

STUDIES ON RELATION BETWEEN INTRINSIC VISCOSITY OF POLYELECTROLYTES IN SOLUTIONS USED FOR LAYER-BY-LAYER SELF-ASSEMBLY AND THEIR CORRESPONDING ADSORPTION AMOUNTS IN THE RESULTANT MULTILAYER MEMBRANES

The adsorption amount of poly(styrene sulfonate)and poly(dimethyldiallyl ammonium chloride)(PSS/PDDA) self-assembled multilayer membranes in designed dipping solvents were measured by UV-Vis-spectroscopy and quartz crystal microbalance(QCM).Intrinsic viscosities of PSS and PDDA in corresponding dipping solvents were determined by an Ubbelohde viscometer.It is found that the adsorption amount of PSS/PDDA self-assembled multilayer membranes built up in different dipping solutions,added salt concentration,p...     

聚电解质结构及盐浓度对基于DNA和聚阳离子的层层组装型大孔薄膜结构的影响

选择2种不同类型的聚阳离子[强电解质型聚二烯丙基二甲基氯化铵(PDDA)和弱电解质型聚盐酸丙烯胺(PAH)], 分别和脱氧核糖核酸(DNA)分子通过静电吸附作用制备层层组装膜. 利用原子力显微镜和紫外-可见分光光度计研究了聚阳离子结构和组装分子溶液中盐(NaCl)浓度对大孔结构及薄膜生长规律的影响. 结果表明, 在DNA/PDDA体系中, 盐浓度对于大孔结构的形成起到关键性作用. 而对于DNA/PAH薄膜体系, 即使增加DNA或PAH溶液中盐的浓度, 也不会有大孔结构出现, 这主要是由PAH分子的弱电解质特性决定的.     

Polyelectrolyte layer-by-layer self-assembly enhanced by electric field and their multilayer membranes for separating isopropanol–water mixtures

An electric field enhanced method is developed for fabricating layer-by-layer (LbL) self-assembly polyelectrolyte multilayer membranes. Three kinds of electric field enhanced polyelectrolyte multilayer membranes (EPEMs), poly(diallyl dimethylammonium chloride)/poly(styrenesulfonate sodium salt) (PDDA/PSS), poly(diallyldimethylammonium chloride)/poly(acrylic acid sodium salt) (PDDA/PAA) and polyethylenimine/poly(acrylic acid sodium salt) (PEI/PAA), were self-assembled on a reverse osmosis membrane (ROM). The pervaporation performances of EPEMs for separating isopropanol–water mixtures (90/10, w/w) are all superior to those of corresponding normal self-assembled polyelectrolytes membranes (PEMs), and the selectivity increases with PDDA/PSS, PDDA/PAA and PEI/PAA in order. For (PEI/PAA)₄PEI EPEM, the separation factor is 1075 and permeation flux is 4.05 kg m⁻² h⁻¹ at 70 °C. This novel method speeds up the LbL process, which makes it promising for the practical application of the LbL multilayer membrane.