Synthesis of zinc glutarates with various morphologies using an amphiphilic template and their catalytic activities in the copolymerization of carbon dioxide and propylene oxide

Various heterogeneous zinc glutarate (ZnGA) catalysts were synthesized in solvent systems of various polarities from zinc acetate dihydrate and glutaric acid with and without the aid of an amphiphilic block copolymer, poly(ethylene glycol‐b‐propylene glycol‐b‐ethylene glycol) (PE6400), as a template. The presence of the PE6400 template and the polarity of the solvent significantly affected the morphology, particle size, surface area, and crystallinity of the resulting catalyst. However, all the catalysts had the same crystal lattice unit cell structure and similar surface compositions. The surface compositions of the catalysts were quite different from those of conventionally prepared ZnGA catalysts, that is, those prepared from zinc oxide and glutaric acid in toluene. All these characteristics of the catalysts influenced the ZnGA‐catalyzed copolymerization of carbon dioxide and propylene oxide. The catalytic activities of the catalysts in this copolymerization depended primarily on their surface area and secondarily on their crystallinity; a larger surface area and a higher crystallinity resulted in higher catalytic activity. Of the catalysts that we prepared, the ZnGA catalyst that was prepared in ethanol containing 5.5 wt % water with the PE6400 template, ZnGA‐PE3, exhibited the highest catalytic activity in the copolymerization. The catalytic activity of ZnGA‐PE3 was attributed to its wrinkled petal bundle morphology, which provided a large surface area and high crystallinity. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4079–4088, 2005     

Crosslinkable poly(propylene carbonate): High‐yield synthesis and performance improvement

A crosslinking strategy was used to improve the thermal and mechanical performance of poly(propylene carbonate) (PPC): PPC bearing a small moiety of pendant C?C groups was synthesized by the terpolymerization of allyl glycidyl ether (AGE), propylene oxide (PO), and carbon dioxide (CO₂). Almost no yield loss was found in comparison with that of the PO and CO₂ copolymer when the concentration of AGE units in the terpolymer was less than 5 mol %. Once subjected to UV‐radiation crosslinking, the crosslinked PPC film showed an elastic modulus 1 order of magnitude higher than that of the uncrosslinked one. Moreover, crosslinked PPC showed hot‐set elongation at 65 °C of 17.2% and permanent deformation approaching 0, whereas they were 35.3 and 17.2% for uncrosslinked PPC, respectively. Therefore, the PPC application window was enlarged to a higher temperature zone by the crosslinking strategy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5329–5336, 2006     

Zinc Glutarate Catalyzed Synthesis and Biodegradability of Poly(carbonate-co-ester)s from CO2, Propylene Oxide,and ϵ-Caprolactone

A zinc glutarate (ZnGA) catalyst was prepared from the reaction of zinc oxide and glutaric acid in dry toluene. ZnGA was found to exhibit a catalytic activity for the copolymerization of carbon dioxide (CO₂) and propylene oxide (PO) and the homopolymerization of PO but to reveal no catalytic activity for the homopolymerization of ϵ-caprolactone (CL). The ZnGA-catalyzed polymerization was extended for the terpolymerization of CO₂ with PO and CL, producing poly(propylene carbonate-co-ϵ-caprolactone)s (PPCCLs) with a reasonably high molecular weight in high yields. In the terpolymerization, PO and CL were used as both co-monomers and reaction media, after the reaction completed, the excess co-monomers were easily recovered and reused in the next terpolymerization batch. For the synthesized polymers, enzymatic and biological degradability were investigated.     

Copolymerization of carbon dioxide and propylene oxide by several metallosalen‐based bifunctional catalysts

A series of new metallosalen‐based bifunctional catalysts with Co(III), Cr(III), Fe(III), Mn(III), and Ni(III) were synthesized for the first time, and a detailed study on the mechanism of the copolymerization of CO₂ and propylene oxide (PO) was performed. Meanwhile, the impact factors of the reaction conditions (metal cations, temperature, CO₂ pressure, and reaction time) on catalytic activity and selectivity were investigated. The results indicated that, with the increase of temperature, both the catalyst efficiency and the molecular weight of the copolymer decrease for all the five complexes. The salen‐Co(III) complex demonstrated higher activity under mild conditions: reaction temperature at 30 °C, copolymerization time of 24 hr, and 2 MPa of CO₂ pressure. The DSC curve indicated that the PPC by the salen‐Co(III) complex has the highest T_g of 46.19 °C. DTGA curves demonstrated that there were two thermal degradation peaks: the first is for the ester bond, and the second is for the C C bond.     

Asymmetric,regio‐ and stereo‐selective alternating copolymerization of CO2 and propylene oxide catalyzed by chiral chromium Salan complexes

Chiral chromium complexes of tetradentate N,N′‐disubstituted bis(aminophenoxide) (designated as Salan, a saturated version of Schiff‐base Salen ligand) in conjunction with an ionic quaternary ammonium salt can efficiently catalyze the copolymerization of CO₂ with racemic propylene oxide (rac‐PO) at mild conditions to selectively afford completely alternating poly(propylene carbonate) (PPC) with ～ 95% head‐to‐tail linkages and moderate enantioselectivity. These new catalyst systems predominantly exceed the previously much‐studied SalenCr(III) systems in catalytic activity, polymer enantioselectivity, and stereochemistry control. The chiral diamine backbone, sterically hindered substitute groups on the aromatic rings, and the presence of sp³‐hydridized amino donors and its N,N′‐disubstituted groups in chiral SalanCr(III) complexes all play significant roles in controlling polymer stereochemistry and enantioselectivity. Furthermore, a relationship between polycarbonate enantioselectivity and its head‐to‐tail linkages in relation to regioselective ring‐opening of the epoxide was also discussed on the basis of stereochemical studies of PPCs derived from the copolymerization of CO₂ with chiral PO at various conditions. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6102–6113, 2008     

Study of electronic effect in bifunctional catalysts for the copolymerization of CO2 and PO/CHO

Carbon dioxide (CO₂) is an easily available renewable carbon source that can be used as a comonomer in the catalytic ring-opening polymerization of epoxides to form aliphatic polycarbonates. Herein, a series of new Salen-Co(III) bifunctional catalysts were synthesized for the first time, and they were studied to catalyze the copolymerization of CO₂ and propylene oxide (PO)/cyclohexene oxide (CHO). At the same time, the effects of reaction conditions (electronic effect, temperature, time) on catalytic activity and selectivity were investigated. The results show that the Salen-Co(III) complexes with electron-withdrawing groups have higher selectivity and activity for propylene carbonate (PPC)/cyclohexylene carbonate (PCHC). At the same time, the Salen-Co(III) complexes can better catalyze the copolymerization of CHO and CO₂ than that of PO and CO₂. The catalytic efficiency of the four complexes increased with increasing temperature, and the best reaction condition is 80°C, 30 min and 2 MPa of CO₂.     

Regio‐regular structure high molecular weight poly(propylene carbonate) by rare earth ternary catalyst and Lewis base cocatalyst

Lewis base modification strategy on rare earth ternary catalyst was disclosed to enhance nucleophilic ability of active center during copolymerization of carbon dioxide and propylene oxide (PO), poly(propylene carbonate) (PPC) with H‐T linkages over 83%, and number–average molecular weight (M_n) up to 100 kg/mol was synthesized at room temperature using Y(CCl₃OO)₃‐ZnEt₂‐glycerine catalyst and 1,10‐phenanthroline (PHEN) cocatalyst. Coordination of PHEN with active Zinc center enhanced the nucleophilic ability of the metal carbonate, which became more regio‐specific in attacking carbon in PO, leading to PPC with improved H‐T linkages. Moreover, the binding of PHEN to active Zinc center also raised the carbonate content of PPC to over 99%, whereas the PPC from common rare earth ternary catalyst was about 96%. Unlike the highly regio‐regular structure PPC but with relatively low molecular weight recently reported in the literature, our high molecular weight regio‐regular PPC did show significant improvement in thermal and mechanical performances. PPC with H‐T linkages up to 83.2% showed glass transition temperature (T_g) of 43.3 °C, while T_g of PPC with H‐T linkages of 69.7% was only 36.1 °C. When H‐T connectivity was raised from 69.7 to 83.2%, the modulus of PPC showed a 78% increase. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4451–4458, 2008     

Preparation of poly(propylene‐co‐γ‐butyrolactone carbonate) and release profiles of drug‐loaded microcapsules

A new aliphatic poly(propylene‐co‐γ‐butyrolactone carbonate) (PPCG) was successfully synthesized through the copolymerization of carbon dioxide, propylene oxide (PO), and γ‐butyrolactone (GBL). GBL was inserted into the backbone of PO–CO₂. The glass transition of PPCG was as high as 16 °C, far higher than that (?1.5 °C) of poly(propylene carbonate) (PPC). The decomposition temperatures of PPCG and PPC were only slightly different. Because of the existence of the GBL ester unit, PPCG had stronger degradability than PPC in a pH 7.4 phosphate‐buffered solution. However, when the PO/GBL ratio increased beyond 5:2, the excessive amount of GBL was not added to the polymerization. PPCG and PPC microcapsules were prepared by the water‐in‐oil‐in‐water multiple‐emulsion method. Glucose was encapsulated. The PPCG microcapsules, about 2 μm in diameter, had smooth and spherical surfaces. The glucose release test revealed that the glucose release speed of the PPCG–glucose microcapsules was more than eight times faster than that of the PPC–glucose microcapsules in a pH 7.4 phosphate‐buffered solution. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2468–2475, 2005     

Temperature‐responsive Catalyst for the Coupling Reaction of Carbon Dioxide and Propylene Oxide

The selective synthesis of polypropylene carbonate (PPC) and cyclic propylene carbonate (CPC) from coupling reaction of CO₂ and propylene oxide (PO) is a long term pursuing target. Here we report that a temperature controllable porphyrin aluminum catalyst using 5,10,15,20‐tetra(1,2,3,4,5,6, 7,8‐octahydro‐1,4:5,8‐dimethanoanthracen‐9‐yl)porphyrin as ligand, once in conjunction with suitable onium salt, achieved single cycloaddition or copolymerization reaction. Only cycloaddition reaction happened at temperature above 75 °C to produce 100% CPC, whereas copolymerization became dominant to afford PPC with selectivity over 99% at 25 °C, and the obtained PPC showed over 99% carbonate linkage and 92% head‐to‐tail structure. Based on systematic analysis of the electronic and steric feature in the porphyrin ligand, it was found that the electronic feature of the substituent in porphyrin ligand was decisive for PPC selectivity, porphyrin ligand bearing strong electron‐donating substituents displayed a significantly reduced tolerance towards increased temperature with respect to PPC formation. Therefore, temperature‐responsive catalyst could be designed by suitable modification in porphyrin ligand, and such accurate synthesis of target product by one catalyst may create a useful and facile platform for selective PPC or CPC production.     

High yield synthesis of biodegradable poly(propylene carbonate) from carbon dioxide and propylene oxide

A novel SalenCo^III (2,4‐dinitrophenoxy) (Salen = N,N'‐bis(3,5‐di‐tert‐butylsalicylidene)‐1,2‐cyclohexanediamino) and 1,10‐phenanthroline monohydrate catalyst system was designed and employed for the copolymerization of CO₂ and propylene oxide (PO). The perfectly alternating copolymerization of CO₂ and PO proceeds effectively under middle temperature and pressure to yield poly(propylene carbonate) with a high yield and a high number average molecular weight of polymer. The structure of polymer was characterized by the IR and NMR measurements. The perfectly alternating copolymer was confirmed. The MALDI‐TOF spectrum insinuates that the copolymerization of CO₂ and PO was initiated by H₂O. Copyright © 2016 John Wiley & Sons, Ltd.     

Dicarboxylic acid promoted immortal copolymerization for controllable synthesis of low‐molecular weight oligo(carbonate‐ether) diols with tunable carbonate unit content

Low‐molecular weight oligo(carbonate‐ether) diols are important raw materials for polyurethane formation, which with tunable carbonate unit content (CU) may endow new thermal and mechanical performances to polyurethane. Herein, facile synthesis of oligo(carbonate‐ether) diols with number average molecular weight (M_n) below 2000 g mol^?1 and CU tunable between 40% and 75% are realized in high activity by immortal copolymerization of CO₂/propylene oxide (PO) using zinc‐cobalt double metal cyanide complex (Zn‐Co‐DMCC) in the presence of sebacic acid (SA). M_n of the oligomer is in good linear relationship to the mole ratio of PO and SA (PO/SA) and hence can be precisely controlled by adjusting PO/SA. Besides, the molecular weight distribution is quite narrow due to the rapid reversible chain transfer in the immortal copolymerization. High pressure and low temperature are favorable for raising CU. In all the reactions, the weight fraction of propylene carbonate (W_PC) can even be controlled as low as 2.0 wt %, and the catalytic activity of Zn‐Co‐DMCC is above 1.0 kgg^?1 cat. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polymer cyclization inhibits thermal decomposition of carbon‐dioxide‐derived poly(propylene carbonate)s

Remarkable enhancement of CO₂‐derived poly(propylene carbonate) (PPC) against thermal decomposition was achieved by cyclization of linear PPCs. Thus, a CO₂‐derived linear vinyl‐telechelic PPC was synthesized by CO₂–propylene oxide alternating copolymerization initiated from H₂O followed by an end‐capping esterification with 4‐pentenoic acid. Cyclic PPC was synthesized by the end‐to‐end intramolecular reaction of the vinyl‐telechelic linear PPC by metathesis condensation. Comparison of the thermal decomposition temperature (T_d) with linear and cyclic PPCs confirms surprisingly enhanced T_ds of cyclic PPCs. The elimination of chain ends through cyclization is indeed valuable for enhancing T_d of CO₂‐derived PPCs and thus turn the spotlight on the materials design utilizing CO₂. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3336–3342     

Mechanistic insight into initiation and chain transfer reaction of CO2/cyclohexene oxide copolymerization catalyzed by zinc?cobalt double metal cyanide complex catalysts

Although zinc? cobalt (III) double metal cyanide complex (Zn? Co (III) DMCC) catalyst is a highly active and selective catalyst for carbon dioxide (CO₂)/cyclohexene oxide (CHO) copolymerization, the structure of the resultant copolymer is poorly understood and the catalytic mechanism is still unclear. Combining the results of kinetic study and electrospray ionization‐mass spectrometry (ESI‐MS) spectra for CO₂/CHO copolymerization catalyzed by Zn? Co (III) DMCC catalyst, we disclosed that (1) the short ether units were mainly generated at the early stage of the copolymerization, and were hence in the “head” of the copolymer and (2) all resultant PCHCs presented two end hydroxyl (? OH) groups. One end ? OH group came from the initiation of zinc? hydroxide (Zn? OH) bond and the other end ? OH group was produced by the chain transfer reaction of propagating chain to H₂O (or free copolymer). Adding t‐BuOH (CHO: t‐BuOH = 2:1, v/v) to the reaction system led to the production of fully alternating PCHCs and new active site of Zn? Ot‐Bu, which was proved by the observation of PCHCs with one end ? Ot‐Bu (and ? OCOOt‐Bu) group from ESI‐MS and ¹³C NMR spectra. Moreover, Zn?OH bond in Zn? Co (III) DMCC catalyst was also characterized by the combined results from FT‐IR, TGA and elemental analysis. This work provided new evidences that CO₂/CHO copolymerization was initiated by metal? OH bond. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Stereoregular polycarbonate synthesis: Alternating copolymerization of CO2 with aliphatic terminal epoxides catalyzed by multichiral cobalt(III) complexes

Completely stereoregular polycarbonate synthesis was achieved with the use of unsymmetric multichiral cobalt‐based complexes bearing a derived chiral BINOL and an appended 1,5,7‐triabicyclo[4.4.0] dec‐5‐ene as catalyst for the copolymerization of CO₂ and aliphatic terminal epoxides at mild conditions. The (S,S,S)‐Co(III) complex 1c with sterically hindered substituent group is more stereoregular catalyst for the copolymerization of CO₂ and racemic propylene oxide to afford a perfectly regioregular poly(propylene carbonate) (PPC), with >99% head‐to‐tail linkages, >99% carbonate linkages, and a K_rel of 24.4 for the enchainment of (R)‐epoxide over (S)‐epoxide. The isotactic PPC exhibits an enhanced glass transition temperature of 47 °C, which is 10–12 °C higher than that of the corresponding irregular polycarbonate. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Catalytic Chain Transfer Copolymerization of Propylene Oxide and CO2 using Zinc Glutarate Catalyst

Oligo and poly(propylene ether carbonate)-polyols with molecular weights from 0.8 to over 50 kg/mol and with 60–92 mol % carbonate linkages were synthesized by chain transfer copolymerization of carbon dioxide (CO₂) and propylene oxide (PO) mediated by zinc glutarate. Online-monitoring of the polymerization revealed that the CTA controlled copolymerization has an induction time which is resulting from reversible catalyst deactivation by the CTA. Latter is neutralized after the first monomer additions. The outcome of the chain transfer reaction is a function of the carbonate content, i. e. CO₂ pressure, most likely on account of differences in mobility (diffusion) of the various polymers. Melt viscosities of poly(ether carbonate)diols with a carbonate content between 60 and 92 mol % are reported as function of the molecular weight, showing that the mobility is higher when the ether content is higher. The procedure of PO/CO₂ catalytic chain copolymerization allows tailoring the glass temperature and viscosity.     

A one‐step strategy for aliphatic poly(carbonate‐ester)s with high performance derived from CO2, propylene oxide and l‐lactide

To improve the performance of PPC, aliphatic poly(carbonate‐ester)s were prepared in one‐step strategy from the terpolymerization of CO₂, propylene oxide (PO), and l ‐lactide (L ‐LA) catalyzed by zinc glutarate. Consequently giving high‐molecular weight terpolymers (PPCLAs) in a very high yield (8450.8–9435.8 g mol^?1 of Zn). The resulting terpolymers PPCLAs were characterized by ¹H NMR, showing that PPCLAs had an almost alternating structure for the components of CO₂, PO, and L‐LA. The influence of molecular weight and L‐LA content on the properties of PPCLAs was also investigated. Differential scanning calorimetry and thermogravimetric analysis (measurements revealed that the glass transition temperature (T _g) and thermal decomposition temperature (T _d) of PPCLAs are all much higher than those of PPC and increased with increasing molecular weight and L‐LA content. Tensile tests showed that the high mechanical properties of PPCLAs are due to the introduction of L‐LA into the copolymerization of CO₂ and PO. Furthermore, PPCLA4 exhibits high degradability, and after 10 weeks, the weight loss increases up to 6.58%, which is significantly higher than that of PPC of 4.58%. Copyright © 2016 John Wiley & Sons, Ltd.     

Copolymerization of carbon dioxide and propylene oxide under inorganic oxide supported rare earth ternary catalyst

Recently, rare earth ternary coordination catalyst represented as Y(CCl₃OO)₃‐Glycerin‐ZnEt₂ has been used for producing poly(propylene carbonate) (PPC, an alternating copolymer of carbon dioxide and propylene oxide) in industry scale, but its catalytic activity needs further improvement. One reason for the relatively low catalytic activity lied in that only 11.7% of active center was efficient due to possible embedding of active center in the heterogeneous catalyst. In this report, supporting strategy was developed, where Y(CCl₃OO)₃‐Glycerin‐ZnEt₂ was supported on various inorganic oxides. Two supporting methods were carried out. One way was to mix Y(CCl₃OO)₃‐Glycerin with inorganic oxide first and then ZnEt₂ was dropped to form the supported catalyst, and the other was to make Y(CCl₃OO)₃‐Glycerin‐ZnEt₂ at first and then mixing with inorganic oxides. The former showed decreasing catalytic activity compared with corresponding unsupported rare earth ternary catalyst, while an improvement of 16–36% in catalytic activity was realized in the latter. PPC with an average number molecular weight (M_n) of over 100 kg/mol and carbonate unit (CU) content of higher than 96% was prepared by both supported catalysts. The catalytic activity of the supported catalyst depended significantly on the supports, which increased in the following order: α‐Al₂O₃ < MgO < ZnO ≈ SiO₂ <γ‐Al₂O₃. γ‐Al₂O₃ was the best support for rare earth ternary catalyst, which showed a remarkable 36% increase in catalytic activity, corresponding to the utilization of 17% of active center. Although MgO supported catalyst gave only an 8% increase in catalytic activity, the M_n and CU content of PPC were raised to about 143 kg/mol and 99%, whereas the PPC from common rare earth ternary catalyst was about 108 kg/mol and 97%, respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Alternating copolymerization of propylene oxide and carbon dioxide with highly efficient and selective (salen)Co(III) catalysts: Effect of ligand and cocatalyst variation

Synthetic routes to a series of new (salen)CoX (salen = N,N′-bis(salicylidene)-1,2-diaminoalkane; X = Br or pentafluorobenzoate (OBzF₅)) species are described. Several of these complexes are active for the copolymerization of propylene oxide (PO) and CO₂, yielding regioregular poly(propylene carbonate) (PPC) without the generation of propylene carbonate byproduct. Variation of the salen ligand, as well as the inclusion of organic-based ionic or Lewis basic cocatalysts, has dramatic effects on the resultant (salen) CoX catalytic activity. Highly active (R,R)-(salen- 1 )CoOBzF₅ (salen- 1 = N,N′-bis(3,5- di-tert-butylsalicylidene)-1,2-diaminocyclohexane) catalysts with [Ph₄P]Cl or [PPN]Y ([PPN] = bis(triphenylphosphine)iminium; Y = Cl or OBzF₅) cocatalysts exhibited turnover frequencies up to 720 h⁻¹ for rac-PO/CO₂ copolymerization, yielding PPC with greater than 90% head-to-tail connectivity. Additionally, the (R,R)-(salen- 1 )CoOBzF₅/[PPN]Cl catalyst system demonstrated a k_rel of 9.7 for the enchainment of (S)- over (R)-PO when the copolymerization was carried out at low temperatures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5182–5191, 2006     

Concerning the Deactivation of Cobalt(III)‐Based Porphyrin and Salen Catalysts in Epoxide/CO2 Copolymerization

Functioning as active catalysts for propylene oxide (PO) and carbon dioxide copolymerization, cobalt(III)‐based salen and porphyrin complexes have drawn great attention owing to their readily modifiable nature and promising catalytic behavior, such as high selectivity for the copolymer formation and good regioselectivity with respect to the polymer microstructure. Both cobalt(III)–salen and porphyrin catalysts have been found to undergo reduction reactions to their corresponding catalytically inactive cobalt(II) species in the presence of propylene oxide, as evidenced by UV/Vis and NMR spectroscopies and X‐ray crystallography (for cobalt(II)–salen). Further investigations on a TPPCoCl (TPP=tetraphenylporphyrin) and NaOMe system reveal that such a catalyst reduction is attributed to the presence of alkoxide anions. Kinetic studies of the redox reaction of TPPCoCl with NaOMe suggests a pseudo‐first order in cobalt(III)–porphyrin. The addition of a co‐catalyst, namely bis(triphenylphosphine)iminium chloride (PPNCl), into the reaction system of cobalt(III)–salen/porphyrin and PO shows no direct stabilizing effect. However, the results of PO/CO₂ copolymerization by cobalt(III)–salen/porphyrin with PPNCl suggest a suppressed catalyst reduction. This phenomenon is explained by a rapid transformation of the alkoxide into the carbonate chain end in the course of the polymer formation, greatly shortening the lifetime of the autoreducible PO‐ring‐opening intermediates, cobalt(III)–salen/porphyrin alkoxides.     

Cobalt catalysts for the alternating copolymerization of propylene oxide and carbon dioxide: combining high activity and selectivity

Synthetic pathways to (salcy)CoX (salcy = N,N'-bis(3,5-di-tert-butylsalicylidene)-1,2-diaminocyclohexane; X = halide or carboxylate) complexes are described. Complexes (R,R)-(salcy)CoCl, (R,R)-(salcy)CoBr, (R,R)-(salcy)CoOAc, and (R,R)-(salcy)CoOBzF(5) (OBzF(5) = pentafluorobenzoate) are highly active catalysts for the living, alternating copolymerization of propylene oxide (PO) and CO(2), yielding poly(propylene carbonate) (PPC) with no detectable byproducts. The PPC generated using these catalyst systems is highly regioregular and has up to 99% carbonate linkages with a narrow molecular weight distribution (MWD). Inclusion of the cocatalysts [PPN]Cl or [PPN][OBzF(5)] ([PPN] = bis(triphenylphosphine)iminium) with complex (R,R)-(salcy)CoCl, (R,R)-(salcy)CoBr, or (R,R)-(salcy)CoOBzF(5) results in remarkable activity enhancement of the copolymerization as well as improved stereoselectivity and regioselectivity with maximized reactivity at low CO(2) pressures. In the case of [PPN]Cl with (R,R)-(salcy)CoOBzF(5), an unprecedented catalytic activity of 620 turnovers per hour is achieved for the copolymerization of rac-PO and CO(2), yielding iso-enriched PPC with 94% head-to-tail connectivity. The stereochemistry of the monomer and catalyst used in the copolymerization has dramatic effects on catalytic activity and the PPC microstructure. Using catalyst (R,R)-(salcy)CoBr with (S)-PO/CO(2) generates highly regioregular PPC, whereas using (R)-PO/CO(2) with the same catalyst gives an almost completely regiorandom copolymer. The rac-PO/CO(2) copolymerization with catalyst rac-(salcy)CoBr yields syndio-enriched PPC, an unreported PPC microstructure. In addition, (R,R)-(salcy)CoOBzF(5)/[PPN]Cl copolymerizes (S)-PO and CO(2) with a turnover frequency of 1100 h(-1), an activity surpassing that observed in any previously reported system.