纳米复合水凝胶的研究进展

传统水凝胶存在机械性能差、响应速度慢等缺点,限制了它作为新材料的应用前景。纳米材料具有独特的微观尺度结构和性质,在电子学、光学、机械学、生物学等领域展现出巨大的潜力。将无机纳米材料添加入水凝胶中不但有可能提高水凝胶的机械强度,同时还能赋予凝胶特殊的新性能,如电响应性能、紫外吸收性能、磁敏感性能等。因而纳米复合水凝胶成为近期的研究热点。本文综述了纳米复合水凝胶的增强理论、典型制备方法及其功能化研究进展。     

自修复聚乙烯醇/细菌纤维素水凝胶电解质制备及应用

以聚乙烯醇(PVA)、细菌纤维素(BC)和硫酸为原料,采用物理交联的冻融循环法制备了聚乙烯醇/细菌纤维素复合水凝胶电解质;经过冻融循环后,聚乙烯醇和细菌纤维素形成了大量的分子间氢键,赋予复合水凝胶良好的自修复性能和力学性能.探讨了纤维素含量对水凝胶电解质力学性能和离子电导率的影响,结果表明,BC含量为0.6％时复合水凝...     

石墨烯基水凝胶的研究进展

石墨烯具有独特的导电、导热和力学性能,既能够自组装为电化学性能优良的石墨烯水凝胶,又可以与小分子和聚合物进行复合制备多功能性复合水凝胶,大幅度地拓展了传统水凝胶的应用范围。本文主要分为四部分来综述近些年来石墨烯基水凝胶的研究进展。第一部分简要介绍了石墨烯的研究背景和石墨烯基水凝胶的研究意义。第二部分主要根据石墨烯基水凝胶的组成将其分为石墨烯水凝胶、石墨烯/小分子和石墨烯/聚合物复合水凝胶三类,分别介绍了它们的制备方法、形成机理和凝胶性能。其中,对石墨烯/小分子复合水凝胶的介绍以石墨烯基超分子水凝胶为主,而对石墨烯/聚合物复合水凝胶的介绍以智能型水凝胶为主。第三部分主要介绍了石墨烯基水凝胶在超级电容器、水处理、控释药物、微流体开关、催化剂载体等方面的应用和发展。最后,对该领域所面临的挑战进行了总结和展望。     

羧甲基纤维素基复合水凝胶的研究及应用进展

羧甲基纤维素(CMC)水凝胶是一种具有亲水性的天然三维聚合物材料,具有高吸水性,因此以羧甲基纤维素钠制备的水凝胶安全无毒可生物降解,被广泛应用于医药、食品、农业和环境等领域,作为保鲜材料、抗菌材料、生物传感器、药物输送系统和去除重金属的吸附剂。本文按CMC复合水凝胶材料来源的不同,分类综述了大分子/CMC水凝胶、单体/CMC水凝胶和无机物/CMC水凝胶的研究进展、功能特性以及应用领域,为羧甲基纤维素复合水凝胶的研究提供一定的思路和理论依据。总结此方向研究中不同材料对羧甲基纤维素复合水凝胶性能的提升情况,同时对羧甲基纤维素水凝胶的应用前景进行了展望。     

纳米复合水凝胶的力学行为与刺激响应性

纳米复合水凝胶（nanocomposite hydrogels,NC凝胶）由于其简便的制备方法、独特的组成、优异的力学性能、高光学透明度以及良好的溶胀/去溶胀性等,引起了广泛的关注.近年来,本课题组在NC凝胶的力学行为及刺激响应性NC凝胶的制备方面取得了可喜的研究成果.观察到新合成的和溶胀平衡的聚N-异丙基丙烯酰胺（PNIPAm）-锂藻土LaponiteNC凝胶的超拉伸性,发现了在大应变下的应变硬化现象;发现利用Mooney-Rivlin方程可以描述NC凝胶的压缩应力-应变,但不能描述较大的应变硬化;Creton模型能很好地描述NC凝胶在大形变下的应力-应变曲线,特别是凝胶的应变硬化;从NC凝胶小应变下的平衡剪切模量得到了有效交联密度,观察到NC凝胶形变-回复过程的迟滞现象,测定了NC凝胶的松弛指数.我们认为NC凝胶具有超拉伸性的原因是其较低的交联密度和适度的松弛速率;在响应性NC凝胶的制备方面,发现了溶胶型Laponite的水分散液的稳定窗口,避免了加入离子性单体引起的聚集沉淀;通过共聚制备了具有超拉伸性、pH响应或温度和pH双响应的透明NC凝胶.本文主要综述了我们课题组在NC凝胶力学行为及响应性NC凝胶领域的一些研究进展,并分析了NC凝胶研究领域仍然未解决的科学问题,以及今后可能的发展方向.     

壳聚糖-聚丙烯酸复合水凝胶的药物控制释放行为

以壳聚糖(Cs)和丙烯酸(AA)为原料,利用自由基聚合法制备了具有孔洞结构的复合水凝胶Cs-PAA,并研究了AA的量、交联剂的量、聚合温度和AA的中和度对水凝胶溶胀度的影响以及复合水凝胶对烟酸的控制释放。 结果表明,Cs-PAA复合水凝胶具有良好的pH值、离子强度敏感性,且溶胀度最高达1228 g/g,其在pH=686的缓冲溶液中的烟酸累积释放率明显大于其在pH=1.80的缓冲溶液,因此Cs-PAA水凝胶可作为肠口服药物的载体。     

酶凝干酪素物理凝胶化过程的有限元模拟

以酶凝干酪素的凝胶化过程为对象,利用有限元方法数值分析了在凝胶化过程中温度场的空间分布和时间演变规律.在此基础上,基于一阶的凝胶化动力学方程,数值模拟了凝胶体系的复剪切模量场,进而分析了材料配方、体系尺寸与冷却方案对复剪切模量场的影响规律.模拟结果表明,由于热阻的差异,体系表面的冷却速率大于内部,表面首先发生凝胶化;而由于预凝胶化阶段的平均冷却速率决定了无穷复剪切模量的值,最终体系内部的复剪切模量超过表面的.     

肝素钠/聚乙烯醇复合水凝胶的制备与性能

通过循环冷冻-解冻法,制成了肝素钠/聚乙烯醇(HS/PVA)复合水凝胶材料。 探讨了不同质量分数肝素钠对复合水凝胶材料的可见光透过率、含水率、亲水性、力学性能以及肝素钠释放量的影响。 结果表明,复合水凝胶的可见光透过率为92%以上,溶胀平衡的含水率为72%~78%,亲水性较纯PVA水凝胶有所提升,拉伸强度和断裂伸长率都稍有下降。 细胞粘附实验结果表明,适量的肝素钠的释放可以达到减少细胞粘附的效果。 这种HS/PVA复合水凝胶材料有望用作人工角膜中心区材料。     

微凝胶增强两性复合水凝胶的制备与性能

将核壳微凝胶包埋在两性基质中,制备了复合水凝胶(CAH)。 研究发现,利用微凝胶与聚合物链之间的物理缠结作用,可以使复合凝胶具有致密的网络结构,力学性能显著提高;复合凝胶对pH和离子强度敏感,呈现出典型的两性聚电解质凝胶的溶胀行为。 同时微凝胶的存在和特殊的复合结构,可赋予CAH两性凝胶基质所不具有的响应性,并实现在高温下快速响应。     

海藻酸钠-锌自修复水凝胶的制备及其对亚甲基蓝的吸附性能

废水处理中迫切需要制备多重刺激响应和具有自修复性能的吸附剂。基于此,本文选择海藻酸钠（ALG）和锌离子（Zn2+）为原料,通过一步法快速（仅2s）制备了超分子水凝胶。所制备的水凝胶显示出多重刺激（pH,金属盐等）响应性和自修复性能,这对吸附有机污染物至关重要。选择亚甲基蓝（MB）为模型染料研究了水凝胶的吸附性能。水凝胶对MB的最大吸附量为5.3 mg/g,对低浓度污染物具有良好的吸附能力（去除率超过80％）。吸附动力学均符合准二级动力学方程,Freundlich模型能很好地拟合等温吸附过程,表明ALG-Zn水凝胶对MB的吸附以多层吸附为主。制备出的ALG-Zn水凝胶适合作为吸附剂应用于废水处理。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.