Determination of Melamine in Food by SPE and CZE with UV Detection

A novel method for the determination of melamine residue in food was developed using solid-phase extraction and capillary zone electrophoresis with UV detection. Spiked samples were extracted with 1% trichloroacetic acid while 0.03 g sodium deoxycholate was used to precipitate protein in the real samples. After centrifuging and clean-up by solid-phase extraction cartridge, the extract was directly analyzed by CZE–UV. The method was validated and good results were obtained with respect to precision, repeatability and spiked recovery. The limit of detection for melamine varied between 0.25 and 0.5 mg kg^?1. The proposed method was successfully applied for the analysis of melamine in food with total recoveries ranging from 94 to 102% in the spiked range of 0.5–5 mg kg^?1, and the relative standard deviations were between 1.5 and 4.1%.     

Development of novel thin-film solid-phase microextraction materials based on deep eutectic solvents for preconcentration of trace amounts of parabens in surface waters

A green and sensitive thin-film solid-phase microextraction method based on deep eutectic solvent was developed that enables simultaneous isolation, preconcentration, and determination of parabens in surface waters. Six new deep eutectic solvents were synthesized and used directly to prepare thin-film coatings on a stainless steel mesh support. Among the compounds obtained, the highest efficiency in the extraction of parabens was found for a material consisting of trihexyltetradecylphosphonium chloride and n-docosanol in a molar ratio of 1:2. For the proposed method, parameters affecting the extraction efficiency of parabens, such as the coating material, the desorption solvent, the volume of the sample, the pH of the sample, the extraction and desorption time, and the salting-out effect, were optimized. Under optimal conditions, the proposed method allowed us to achieve good precision between 3.6 and 6.5% and recovery ranging from 68.1 to 91.4%. The limits of detection range from 0.018 to 0.055 ng/mL.     

Development of a new strategy for the synthesis of graphene oxide-alumina nanocomposite as an efficient adsorbent for dispersive solid-phase extraction of parabens

The present study investigates the synthesis and application of the graphene oxide-alumina nanocomposite as a new adsorbent for the dispersive solid-phase extraction of three parabens and their determination using high-performance liquid chromatography-ultraviolet detection. The characterization of the synthesized material was accomplished and its size, morphology, chemical composition, porosity, and thermal stability were studied. Application of the proposed strategy for the synthesis of the nanocomposite resulted in the incorporation of Al₂O₃ nanoparticles into graphene oxide nanosheets, further resulting in the exfoliation of graphene oxide nanosheets increasing their surface area. An orthogonal rotatable central composite design was used to optimize the extraction. Under the optimum conditions, the analytical performance of the method showed a suitable linear dynamic range (0.2–100.0 μg/L), reasonable limits of detection (0.03–0.05 μg/L), and preconcentration factors ranging from 128 to 173. Finally, the new validated method was applied for the determination of parabens in some real samples including wastewater, cream, toothpaste, and juice samples with satisfactory recoveries (88%–109%), and relative standard deviations less than 8.7% (n = 3). Results demonstrated that inserting alumina nanoparticles into graphene oxide nanosheets improved the extraction efficiency of parabens, as polar acidic compounds, by providing additional efficient interactions including hydrogen bonding, dipole-dipole, and Brønsted and Lewis acid-base interactions.     

Fabrication of the Metal-Organic Framework Membrane with Excellent Adsorption Properties for Paraben Based on Micro Fibrillated Cellulose

A kind of novel environmental-friendly composite absorbent material was designed and prepared in this paper. Nanoscale metal-organic frameworks(MOFs) were embedded in the skeleton of cotton micro fibrillated cellulose. By scanning electron microscope(SEM), we observed that a large number of MOFs were attached to the cellulose skeleton. In addition, under the condition of 1800 r/min vortex, the structure of the composite material was stable and was not easily damaged by external forces. The water contact angle test showed that the composite material had excellent hydrophilicity and could be used for the adsorption of pollutants. Then, the material was characterized by energy dispersive X-ray spectroscopy(EDX), X-ray diffraction(XRD), Fourier transform infrared spectroscopy(FTIR) and BET adsorption. Through verification, the material had very stable reusability(n=10). The composite material was applied to the solid phase extraction of water samples, such as rain water, toning water and fruit juice, and was quantitatively analyzed by high performance liquid chromatography(HPLC)-UV. This method was then applied to the extraction of four parabens(methyl-, ethyl-, propyl-, and butyl-paraben) from real samples, yielding limits of detection(LODs) of 0.29-0.58 ng/mL. The linear range was 2-500 ng/mL. The inter-day and intra-day recoveries were 90.7%-106.0% and 87.1%-109.3%, respectively(relative standard deviation<10.8%).     

Self‐assembly of poly(ionic liquid) functionalized mesoporous magnetic microspheres for the solid‐phase extraction of preservatives from milk samples

In this work, a novel, rapid, and simple analytical method was proposed for the detection of parabens in milk sample by gas chromatography coupled with mass spectrometry. At the same time, milk sample was pretreated by magnetic solid phase extraction, which detected up to five parabens. A series of important parameters of magnetic solid phase extraction were investigated and optimized, such as pH value of loading buffer, amount of material, adsorption time, ionic strength, eluting solvents, and eluting time. Under the optimized conditions, the corresponding values were more than 0.9991, limits of detection and the limit of quantification were 0.1 and 0.5 ng/mL, respectively. In addition, the recoveries were achieved in range of 95–105%, the liner range were within 0.1–600 ng/mL, and the relative standard deviations were even lower than 5%.     

Application of dispersive liquid–liquid microextraction for the preconcentration of eight parabens in real samples and their determination by high‐performance liquid chromatography

A simple and sensitive method for the simultaneous determination of eight parabens in human plasma and urine samples was developed. The samples were preconcentrated using dispersive liquid–liquid microextraction based on the solidification of floating organic drops and determined by high‐performance liquid chromatography with ultraviolet detection. The influence of variables affecting the extraction efficiency was investigated and optimized using Placket–Burman design and Box–Behnken design. The optimized values were: 58 μL of 1‐decanol (as extraction solvent), 0.65 mL methanol (as disperser solvent), 1.5% w/v NaCl in 5.0 mL of sample solution, pH 10.6, and 4.0 min centrifugation at 4000 rpm. The extract was injected into the high‐performance liquid chromatography system for analysis. Under the optimum conditions, the linear ranges for eight parabens in plasma and urine were 1.0–1000 ng/mL, with correlation coefficients above 0.994. The limit of detection was 0.2–0.4 and 0.1–0.4 ng/mL for plasma and urine samples, respectively. Relative recoveries were between 80.3 and 110.7%, while relative standard deviations were less than 5.4%. Finally, the method was applied to analyze the parabens in 98 patients of primary breast cancer. Results showed that parabens existed widely, at least one paraben detected in 96.9% (95/98) of plasma samples and 98.0% (96/98) of urine samples.     

Simultaneous derivatization and air‐assisted liquid–liquid microextraction of some parabens in personal care products and their determination by GC with flame ionization detection

A simultaneous derivatization/air‐assisted liquid–liquid microextraction technique has been developed for the sample pretreatment of some parabens in aqueous samples. The analytes were derivatized and extracted simultaneously by a fast reaction/extraction with butylchloroformate (derivatization agent/extraction solvent) from the aqueous samples and then analyzed by GC with flame ionization detection. The effect of catalyst type and volume, derivatization agent/extraction solvent volume, ionic strength of aqueous solution, pH, numbers of extraction, aqueous sample volume, etc. on the method efficiency was investigated. Calibration graphs were linear in the range of 2–5000 μg/L with squared correlation coefficients >0.990. Enhancement factors and enrichment factors ranged from 1535 to 1941 and 268 to 343, respectively. Detection limits were obtained in the range of 0.41–0.62 μg/L. The RSDs for the extraction and determination of 250 μg/L of each paraben were <4.9% (n = 6). In this method, the derivatization agent and extraction solvent were the same and there is no need for a dispersive solvent, which is common in a traditional dispersive liquid–liquid microextraction technique. Furthermore, the sample preparation time is very short.     

Preparation and performance analysis of monodisperse glycidyl methacrylate modified restricted access media-imprinted materials

Using monodisperse poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) as the matrix, and pefloxacin template molecules, a novel restricted-access medium molecularly imprinted polymers with Bovine serum albumin crosslinked on its surface was prepared through reversible addition–fragmentation chain-transfer polymerization. Then, the obtained material was employed in dispersive solid-phase extraction to analyze the fluoroquinolones in untreated egg samples by high-performance liquid chromatography–ultraviolet detection. Adsorption performance revealed a good binding amount (40.72 mg/g), fast binding kinetics (25 min), satisfactory selectivity, and good ability to eliminate matrix interference. The reusability experiments indicated the materials have good reusable performance after repetition. Under the optimized conditions, restricted access media-molecularly imprinted polymers-dispersive solid-phase extraction was combined with high-performance liquid chromatography–ultraviolet to enrich fluoroquinolones in untreated eggs, good limit of detection (1.31–3.15 μg/L) and high recovery (89.5–96.8%) were obtained. The results showed that the prepared restricted-access material is promising for the direct detection of antibiotics in complex samples.     

Green dispersive solid-phase microextraction of melamine using crosslinked beta-cyclodextrin with citric acid followed by high-performance liquid chromatography

In this research, a green approach for dispersive solid phase microextraction was introduced for the extraction and determination of melamine in various matrices such as infant formula and hot water in a melamine bowl. In this way, a natural polar polymer called ß-cyclodextrin has been cross-linked with citric acid to create a water-insoluble adsorbent. The extraction was carried out by dispersion of the sorbent into the sample solution. The effective parameters on the extraction efficiency of the melamine, including ion strength, extraction time, sample volume, amount of absorbent, pH, type of desorption solvent, desorption time, and desorption solvent volume were optimized by one variable at a time approach. Under the optimal conditions, the method showed a good linear dynamic range for melamine in the range of 1–1000 μg/L with a coefficient of determination of 0.9985. The obtained limit of detection was 0.3 μg/L. The intra-day and inter-day relative standard deviations (n = 3) were 3.1% and 3.2% respectively. Lastly, this technique was applied to extract and determine the analyte in a melamine bowl and infant formula with acceptable and satisfactory results.     

Primary amide-functionalized cyclotricatechylene covalent organic frameworks membrane for efficient enrichment of melamine and its derivatives in migration solution of food contact materials

A highly chemically stable primary amide-functionalized cyclotricatechylene covalent organic framework was synthesized by an irreversible reaction and a post-synthetic modification. It possessed a rod-like morphology and exhibited strong solvent stability owing to the polyether bonds. The material showed good adsorption performance for melamine and its derivatives and adsorption mechanism was investigated by molecular simulations. The adsorbent was coated on the nylon-66 membrane to prepare the enrichment membrane. Under optimized conditions, an in-syringe membrane-based extraction method, combined with ultra-high performance liquid chromatography-tandem mass spectrometry was developed for the analysis of melamine and six melamine derivatives in the migration solution. A good linearity was obtained with correlation coefficients ranging from 0.9924 to 0.9995. The limits of detection were 1–200 ng/L and the limits of quantification were 3–500 ng/L. This method was successfully applied to the migration solution of sushi bamboo rolling mats with spiked recoveries of 73.2%–115% and relative standard deviations of 0.9%–9.9%. This work shows a practical and perspective approach for the efficient enrichment of food contact material hazards.     

Determination of parabens and endocrine-disrupting alkylphenols in soil by gas chromatography–mass spectrometry following matrix solid-phase dispersion or in-column microwave-assisted extraction: a comparative study

Two rapid methods were evaluated for the simultaneous extraction of seven parabens and two alkylphenols from soil based on matrix solid-phase dispersion (MSPD) and microwave-assisted extraction (MAE). Soil extracts were derivatized with N,O-bis(trimethylsilyl)trifluoroacetamide and analyzed by gas chromatography with mass spectrometry. Extraction and clean-up of samples were carried out by both methods in a single step. A glass sample holder, inside the microwave cell, was used in MAE to allow the simultaneous extraction and clean-up of samples and shorten the MAE procedure. The detection limits achieved by MSPD were lower than those obtained by MAE because the presence of matrix interferences increased with this extraction method. The extraction yields obtained by MSPD and MAE for three different types of soils were compared. Both procedures showed good recoveries and sensitivity for the determination of parabens and alkylphenols in two of the soils assayed, however, only MSPD yielded good recoveries with the other soil. Finally, MSPD was applied to the analysis of soils collected in different sites of Spain. In most of the samples analyzed, methylparaben and butylparaben were detected at levels ranging from 1.21 to 8.04 ng g⁻¹ dry weight and 0.48 to 1.02 ng g⁻¹ dry weight, respectively.     

Miniaturized matrix solid‐phase dispersion coupled with supramolecular solvent‐based microextraction for the determination of paraben preservatives in cream samples

An analytical method is presented for the determination of paraben preservatives in semisolid cream samples by matrix solid‐phase dispersion combined with supramolecular solvent‐based microextraction. Due to the oily and sticky nature of the sample matrix, parabens were first extracted from the samples by matrix solid‐phase dispersion using silica as sorbent material with a clean‐up performed with tetrahydrofuran in the elution step. The eluate (500 μL), 1‐decanol (120 μL), and water (4.4 mL) were then mixed in a polyethylene pipette to form supramolecular solvent. Finally, the analytes in the supramolecular solvent were separated and determined by liquid chromatography with ultraviolet detection. Under optimal extraction conditions, the extraction recoveries of the studied compounds were obtained in the range of 63–83%. The limits of detection for the analytes were between 0.03 and 0.04 μg/g. The precision of the method varied between 4.0–6.7 (intraday) and 6.2–7.9% (interday). Finally, the optimized procedure was applied to the determination of the target preservatives in a variety of cream samples (diaper rash, skin allergy, face and hand moisturizing) with satisfactory recoveries (86–102%).     

Facile synthesis of a novel magnetic covalent organic frameworks for extraction and determination of five fungicides in Chinese herbal medicines

A novel magnetic covalent organic framework was synthesized via a one-step coating approach with solvothermal reaction employing 2,4,6-tris(4-aminophen-yl)-1,3,5-triazine and 2,4,6-triformylphloroglucinol as two building blocks by covalent bonding. The prepared magnetic covalent organic frameworks were properly characterized by different techniques and employed as adsorbents of magnetic solid-phase extraction. An analytical method was developed for the simultaneous determination of five fungicides in two Chinese herbal medicine samples via magnetic solid-phase extraction coupled to ultra high performance liquid chromatography with tandem mass spectrometry analysis. Under optimized magnetic solid-phase extraction conditions, the method exhibited satisfactory recoveries (74.0−109.6%) with relative standard deviations of 0.4−4.6%, low limits of detection (0.003−0.015 μg/kg), and good linearity (R² > 0.9960). Compared with the traditional extraction method, the proposed method required a lower amount of adsorbent (3 mg) and extraction time (5 min). The adsorbent also had favorable reusability (not less than eight times). Therefore, the magnetic covalent organic frameworks could be a promising adsorbent for the extraction and quantitation of fungicides in Chinese herbal medicines.     

Preparation of flower-like molybdenum disulfide for solid-phase extraction of N-nitrosoamines in environmental water samples

In this paper, a flower-like molybdenum disulfide material was prepared by hydrothermal method and was first used as adsorbents in the solid-phase extraction process for enriching N-nitrosoamines. Molybdenum disulfide exhibited three-dimensional petal-like microspheres with about 500 nm in diameter. The relevant analyte extraction and elution parameters (sample volumes, solution pH, washing solvents, elution solvents, and elution volumes) were optimized to improve the solid-phase extraction efficiency. The solid-phase extraction process coupled with high-performance liquid chromatography-tandem mass spectrometry for determining N-nitrosoamines in environmental water samples was established. The limits of detection were in the range of 0.01–0.05 ng/mL. The satisfactory recoveries (68.9–106.1%) were obtained at three different spiked concentrations (2, 5, and 8 ng/mL) in water samples, and the relative standard deviations were between 1.96 and 8.38%. This proposed method not only showed high sensitivity and good reusability but also provided a new adsorbent for enriching trace N-nitrosoamines in environmental water samples.     

Electrophoretic deposition of polyaniline nanofibers on a stainless steel wire as an adsorbent for determination of tamoxifen by SPME/GC–FID in urine samples

Polyaniline nanofiber films were fabricated on the surface of stainless steel wire via a controllable and simple electrophoretic deposition route from a nonaqueous colloidal suspension consisting of polyaniline nanofibers. The prepared coating material was then characterized by field emission scanning electron microscopy equipped with energy dispersive spectroscopy and elemental mapping analysis. The fabricated polyaniline film-coated stainless steel wire was then utilized as an effective and novel sorbent phase for solid-phase microextraction of tamoxifen for subsequent gas chromatography/flame ionization detection of this anticancer drug. Parameters consisting of the temperature, extraction time, salt concentration, agitation speed, pH, temperature and time of desorption were studied and optimized using a one-at-a-time strategy. Under the optimum conditions, detection limit (S/N = 3), the limit of quantification (10/3 limit of detection), linear dynamic range, repeatability and reproducibility values of 0.51 μg L⁻¹, 1.7 μg L⁻¹, 2–1,130 μg L⁻¹, 5.7% and 8.6% were attained, respectively. The prepared fiber can preserve 90% of its efficacy after 20 consecutive cycles, demonstrating the suitable thermal stability and cyclability of the proposed solid-phase microextraction coating material for the determination of tamoxifen by gas chromatography/flame ionization detection. The route was effectively utilized to determine tamoxifen in urine samples, with relative recoveries ranging from 89 to 106%.     

Validation of a confirmatory method for the determination of melamine in egg by gas chromatography-mass spectrometry and ultra-performance liquid chromatography-tandem mass spectrometry

A sensitive and reliable method was developed and validated for detection and confirmation of melamine in egg based on gas chromatography-mass spectrometry (GC-MS) and ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). Trichloroacetic acid solution was used for sample extraction and precipitation of proteins. The aqueous extracts were subjected to solid-phase extraction by mixed-mode reversed-phase/strong cation-exchange cartridges. Using ultra-performance liquid chromatography and electrospray ionization in the positive ion mode, melamine was determined by LC-MS/MS, which was completed in 5 min for each injection. For the GC-MS analysis, extracted melamine was derivatized with N,O-bis(trimethylsilyl)trifluoracetamide prior to selected ion monitoring detection in electron impact mode. The average recovery of melamine from fortified samples ranged from 85.2% to 103.2%, with coefficients of variation lower than 12%. The limit of detection obtained by GC-MS and UPLC-MS/MS was 10 and 5 μg kg⁻¹, respectively. This validated method was successfully applied to the determination of melamine in real samples from market.     

Molecularly imprinted polymer as SPE sorbent for selective extraction of melamine in dairy products

In this paper, a highly selective sample cleanup procedure combining molecular imprinting and solid-phase extraction (MI-SPE) was developed for the isolation of melamine in dairy products. The molecularly imprinted polymer (MIP) was prepared using melamine as the template molecule, methacrylic acid as the functional monomer and ethylene glycol dimethacrylate as the cross-linking monomer. The melamine imprinted polymer was used as selective sorbent for the solid-phase extraction of melamine from dairy products. An off-line MI-SPE method followed by high-performance liquid chromatography with diode-array detection for the detection of melamine was also established. The mean recoveries of melamine from ultra-heat treatment (UHT) milk and milk powders were 92.9-98.0% and 91.6-102.8%, respectively. Good linearity was obtained from 0.5 μM to 10 μM (r > 0.999) with a quantitation limit of 0.5 μmol/L (0.06 ppm) which was sufficient to analyse melamine at the maximum level permitted by U.S. Food and Drug Administration (1 ppm) in dairy products. It was demonstrated that the proposed MI-SPE-HPLC method could be applied to direct determination of melamine in dairy products.     

Novel cyromazine imprinted polymer applied to the solid-phase extraction of melamine from feed and milk samples

A water compatible molecularly imprinted polymer (MIP) using cyromazine as a mimic template, methacrylic acid as the functional polymer and ethylene glycol dimethacrylate as the cross-linker was synthesized and used to extract melamine from feed and milk samples via a molecularly imprinted solid-phase extraction (MISPE) protocol. Optimum retention of melamine on the MISPE cartridge was achieved using methanol, and the interferences in the samples were effectively washed out. The binding capacity of the polymer toward melamine was found to be about 500 μg of melamine/g of polymer. The recoveries of 2 μg and 20 μg melamine standard spiked into water extract of blank feeds and milk samples were between 83.4% and 103%, with relative standard deviation <5.6%. The cyromazine-MIP demonstrated high cross-reactivity for melamine and low affinity to cyanuric acid. The ionic bond interaction was regarded as the main factors that dominated the retention of the melamine on the MISPE cartridge.     

Selective extraction of apixaban from plasma by dispersive solid-phase microextraction using magnetic metal organic framework combined with molecularly imprinted polymer nanocomposite

This research aims to synthesize a specific and efficient sorbent to use in the extraction of apixaban from human plasma samples and its determination by high-performance liquid chromatography-tandem mass spectrometry. High specific surface area of metal-organic framework, magnetic property of iron oxide nanoparticles, selectively of molecular imprinted polymer toward the analyte, and the combination of dispersive solid-phase extraction method with a sensitive analysis system provided an efficient analytical method. In this study, first, a molecularly imprinted polymer combined with magnetic metal organic framework nanocomposite was prepared and then characterized using different techniques. Then the sorbent particles were used for selective extraction of the analyte from plasma samples. The efficiency of the method was improved by optimizing effective parameters. According to the validation results, wide linear range (1.02–200 ng mL⁻¹), acceptable coefficient of determination (0.9938), low limit of detection (0.32 ng mL⁻¹) and limit of quantification (1.02 ng mL⁻¹), high extraction recovery (78%), and good precision (relative standard deviations ≤ 2.9% for intra- (n = 6) and interday (n = 6) precisions) were obtainable using the proposed method. These outcomes showed the high potential of the proposed method for screening apixaban in the human plasma samples.     

Simultaneous derivatization and lighter‐than‐water air‐assisted liquid–liquid microextraction using a homemade device for the extraction and preconcentration of some parabens in different samples

Simultaneous derivatization and air‐assisted liquid–liquid microextraction using an organic that is solvent lighter than water has been developed for the extraction of some parabens in different samples with the aid of a newly designed device for collecting the extractant. For this purpose, the sample solution is transferred into a glass test tube and a few microliters of acetic anhydride (as a derivatization agent) and p‐xylene (as an extraction solvent) are added to the solution. After performing the procedure, the homemade device consists of an inverse funnel with a capillary tube placed into the tube. In this step, the collected extraction solvent and a part of the aqueous solution are transferred into the device and the organic phase indwells in the capillary tube of the device. Under the optimal conditions, limits of detection and quantification for the analytes were obtained in the ranges of 0.90–2.7 and 3.0–6.1 ng/mL, respectively. The enrichment and enhancement factors were in the ranges of 370–430 and 489–660, respectively. The method precision, expressed as the relative standard deviation, was within the range of 4–6% (n = 6) and 4–9% (n = 4) for intra‐ and interday precisions, respectively. The proposed method was successfully used for the determination of methyl‐, ethyl‐, and propyl parabens in cosmetic, hygiene and food samples, and personal care products.