Comprehensive survey of Nd substitution In La2Mo2O9 oxide-ion conductor

Differential thermal analysis coupled to temperature-controlled diffraction have given evidence of a topological metastability phenomenon in an extended compositional range of the La_2−xNd_xMo₂O₉ solid solution. A metastable-stable phase diagram is proposed for this series of LAMOX-type fast oxide-ion conductors. In the Nd range 0<x?0.35, a freezing of the oxygen/vacancy disorder of the β-phase at ambient temperature can be achieved through a splat-quenching to water-ice mixture or/and shaping/sintering into pellet. In the intermediate 0.4?x?1.2 range, the amount of β-metastable phase grows upon substitution for powders. The negative impact of β-metastable to α phase transition on conductivity tends to disappear through the partial stabilization of the β phase by shaping/sintering.     

Structural and dielectric/ferroelectric properties of (La1−xNdx)2Ti2O7 synthesized by sol-gel route

A series of compounds with the general formula (La_1−xNd_x)₂Ti₂O₇ (0.0≤x≤1.0) has been prepared by the sol-gel method. The decomposition of the gel was characterized by thermo-gravimetric analysis coupled to mass spectrometry, indicating the reaction is achieved above 850 °C. The lattice parameters versus x show an expected decrease in the a and b parameters while c and the β angle remain almost unchanged with respect to the monoclinic symmetry conserved for the full solid solution. Dielectric, piezoelectric and ferroelectric properties were measured on the entire series.     

XRD and Si MAS-NMR spectroscopy across the β-Lu2Si2O7-β-Y2Si2O7 solid solution

Samples in the system Lu_2−xY_xSi₂O₇ (0?x?2) have been synthesized following the sol-gel method and calcined to 1300 °C, a temperature at which the β-polymorph is known to be the stable phase for the end-members Lu₂Si₂O₇ and Y₂Si₂O₇. The XRD patterns of all the compositions studied are compatible with the structure of the β-polymorph. Unit cell parameters are calculated as a function of composition from XRD patterns. They show a linear change with increasing Y content, which indicates a solid solubility of β-Y₂Si₂O₇ in β-Lu₂Si₂O₇ at 1300 °C. ²⁹Si MAS NMR spectra of the different members of the system agree with the XRD results, showing a linear decrease of the ²⁹Si chemical shift with increasing Y content. Finally, a correlation reported in the literature to predict ²⁹Si chemical shifts in silicates is applied here to obtain the theoretical variation in ²⁹Si chemical shift values in the system Lu₂Si₂O₇-Y₂Si₂O₇ and the results compare favorably with the values obtained experimentally.     

Phase relations, crystal chemistry, and dielectric properties in sections of the La2O3-CaO-MgO-TiO2 system

Subsolidus phase equilibria and crystal chemistry were studied for the La₂O₃-MgO-TiO₂ system and for the ternary sections LaMg_1/2Ti_1/2O₃-CaTiO₃-La₂O₃ and LaMg_1/2Ti_1/2O₃-CaTiO₃-La_0.833Mg_0.25Ti_0.75O₃ in the quaternary La₂O₃-CaO-MgO-TiO₂ system. Dielectric properties (relative permittivity and temperature coefficient of resonant frequency, τ_f) were measured at 5-10 GHz and mapped onto the phase equilibria relations to reveal the compositions of temperature-stable (τ_f=0) compounds and mixtures. Phase equilibria relations were obtained by X-ray powder diffraction analysis of approximately 80 specimens prepared by solid-state reactions in air at ∼1450°C. Six ternary phases were found to form in the La₂O₃-MgO-TiO₂ system, including the three previously reported compounds LaMg_1/2Ti_1/2O₃, La₅Mg_0.5Ti_3.5O₁₅, and “La₆MgTi₄O₁₈”; and the new phases La₁₀MgTi₉O₃₄, La₉Mg_0.5Ti_8.5O₃₁, and a perovskite-type solid solution (1−x)LaMg_1/2Ti_1/2O₃-xLa_2/3TiO₃ (0?x?0.5). The phase previously reported as “La₆MgTi₄O₁₈” was found to form off-composition, apparently as a point compound, at La₆Mg_0.913Ti_4.04O₁₈. Indexed experimental X-ray powder diffraction patterns are given for LaMg_1/2Ti_1/2O₃, La₅Mg_0.5Ti_3.5O₁₅, La₆Mg_0.913Ti_4.04O₁₈, La₁₀MgTi₉O₃₄, and La₉Mg_0.5Ti_8.5O₃₁. LaMg_1/2Ti_1/2O₃ exhibits a slightly distorted perovskite structure with ordered B-cations (P2₁/n; a=5.5608(2) Å, b=5.5749(3) Å, c=7.8610(5) Å, β=90.034(4)°). La₅Mg_0.5Ti_3.5O₁₅ (Pm1; a=5.5639(1), c=10.9928(5) Å) and La₆Mg_0.913Ti_4.04O₁₈ (R3m; a=5.5665(1), c=39.7354(9) Å) are n=5 and n=6 members, respectively, of the (111) perovskite-slab series A_nB_n−1O_3n. The new phases La₁₀MgTi₉O₃₄ (a=5.5411(2), b=31.3039(9), c=3.9167(1) Å) and La₉Mg_0.5Ti_8.5O₃₁ (a=5.5431(2), b=57.055(1), c=3.9123(1) Å) are n=5 and n=4.5 members, respectively, of the (110) perovskite-slab series A_nB_nO_3n+2, which exhibit orthorhombic subcells; electron diffraction revealed monoclinic superlattices with doubled c-parameters for both compounds. Extensive perovskite-type solid solutions form in the ternary sections LaMg_1/2Ti_1/2O₃-CaTiO₃-La₂O₃ and LaMg_1/2Ti_1/2O₃-CaTiO₃-La_0.833Mg_0.25Ti_0.75O₃. The La₂O₃-MgO-TiO₂ system contains two regions of temperature-stable (τ_f=0) compositions. The quaternary La₂O₃-CaO-MgO-TiO₂ system contains an extensive single-phase perovskite-type volume through which passes a surface of temperature-stable compositions with permittivities projected to be in the 40-50 range. Traces of this surface occur as lines of τ_f=0 perovskite-type phases in the ternary sections LaMg_1/2Ti_1/2O₃-CaTiO₃-La₂O₃ and LaMg_1/2Ti_1/2O₃-CaTiO₃-La_0.833Mg_0.25Ti_0.75O₃.     

Synthesis and characterization of La2Mo2O9 obtained from freeze-dried precursors

La₂Mo₂O₉ ceramics have been prepared from freeze-dried precursors and their properties compared to those of lantanum molybdate obtained by conventional solid state (SS) reaction. All materials have been characterized by X-ray diffraction, scanning electron microscopy and thermal analysis (TGA/DTA/DSC and dilatometry) to characterize the phase formation and phase transition. When the freeze-dried method was applied, the synthesis temperature required to obtain dense samples was much lower than that for powders obtained by SS reaction. The morphology and structure of the oxide particle are significantly dependent on the synthesis method. The grain size is smaller, whereas the density of sintered pellets is higher for the freeze-dried precursor powder when compared with the SS reaction method. Impedance spectroscopy was used to measure the electrical conductivity of La₂Mo₂O₉ from 548 to 1123 K, in air, and to characterize the blocking effects of grain boundaries.     

Composition-induced structural phase transitions in the (Ba1−xLax)2In2O5+x (0?x?0.6) system

Composition-induced structural phase changes across the high temperature, fast oxide ion conducting (Ba_1−xLa_x)₂In₂O_5+x, 0?x?0.6, system have been carefully analysed using hard mode infrared (IR) powder absorption spectroscopy, X-ray powder diffraction and electron diffraction. An orthorhombic brownmillerite to three-dimensionally disordered cubic perovskite phase transition in this system is signalled by a drastic change in slope of both wavenumber and average line widths of IR spectra as a function of composition. Some evidence is found for the existence of an intermediate tetragonal phase (previously reported to exist from electron diffraction data) around x∼0.2. The new spectroscopic data have been used to compare microscopic and macroscopic strain parameters arising from variation in composition. The strain and spectroscopic data are consistent with first-order character for the tetragonal→orthorhombic transition, while the cubic→tetragonal transition could be continuous. Differences between the variation with composition of spectral parameters and of macroscopic strain parameters are consistent with a substantial order/disorder component for the transitions. There is also evidence for precursor effects within the cubic structure before symmetry is broken.     

The Crystal Structures, Microstructure and Ionic Conductivity of Ba2In2O5 and Ba(InxZr1−x)O3−x/2

This paper describes the results of electron microscopy, high-temperature powder neutron diffraction, and impedance spectroscopy studies of brownmillerite-structured Ba₂In₂O₅ and perovskite structured Ba(In_xZr_1−x)O_3−x/2. The ambient temperature structure of Ba₂In₂O₅ is found to adopt Icmm symmetry, with disorder of the tetrahedrally coordinated (In³⁺) ions of the type observed previously in Sr₂Fe₂O₅. Ba₂In₂O₅ undergoes a ∼6-fold increase in its ionic conductivity over the narrow temperature range from ∼1140 K to ∼1230 K, in broad agreement with previous studies. This transition corresponds to a change from the brownmillerite structure to a cubic perovskite arrangement with disordered anions. Electron microscopy investigations showed the presence of extended defects in all the crystals analyzed. Ba(In_xZr_1−x)O_3−x/2 samples with x=0.1 to 0.9 adopt the cubic perovskite structure, with the lattice parameter increasing with x.     

Phase relations in NaxCrxTi8−xO16 at 1350 °C and crystal structure of hollandite-like Na2Cr2Ti6O16

Phase relations of rutile, freudenbergite, and hollandite structures were examined in the pseudobinary system NaCrO₂-TiO₂ (i.e., Na_xCr_xTi_8−xO₁₆) at 1350 °C. The hollandite structure was obtained in the composition range 1.7?x?2.0. The symmetry of the samples at room temperature was tetragonal for x=1.7 and 1.75, and monoclinic for x=1.8 and above. Single crystals of monoclinic hollandite Na₂Cr₂Ti₆O₁₆ were grown and the structure refinement has been carried out using an X-ray diffraction technique. The space group was I2/m and cell parameters were a=10.2385(11), b=2.9559(9), c=9.9097(11)Å, and β=90.545(9)° with Z=1. The Na ion distribution in the tunnel was markedly deformed from that in the tetragonal form. It was suggested that Cr/Ti ratios were different between the two framework metal sites.     

Crystal structure, thermal expansion and conductivity of anisotropic La1−xSrxGa1−2xMg2xO3−y (x=0.05, 0.1) single crystals

Crystal structure and anisotropy of the thermal expansion of single crystals of La_1−xSr_xGa_1−2xMg_2xO_3−y (x=0.05 and 0.1) were measured in the temperature range 300-1270 K. High-resolution X-ray powder diffraction data obtained by synchrotron experiments have been used to determine the crystal structure and thermal expansion. The room temperature structure of the crystal with x=0.05 was found to be orthorhombic (Imma, Z=4, a=7.79423(3) Å, b=5.49896(2) Å, c=5.53806(2) Å), whereas the symmetry of the x=0.1 crystal is monoclinic (I2/a, Z=4, a=7.82129(5) Å, b=5.54361(3) Å, c=5.51654(4) Å, β=90.040(1)°). The conductivity in two orthogonal directions of the crystals has been studied. Both, the conductivity and the structural data indicate three phase transitions in La_0.95Sr_0.05Ga_0.9Mg_0.1O_2.92 at 520-570 K (Imma-I2/a), 770 K (I2/a-R3c) and at 870 K (R3c-R-3c), respectively. Two transitions at 770 K (I2/a-R3c) and in the range 870-970 K (R3c-R-3c) occur in La_0.9Sr_0.1Ga_0.8Mg_0.2O_2.85.     

La doping of the Sr2CoWO6 double perovskite: A structural and magnetic study

La-doped Sr₂CoWO₆ double perovskites have been prepared in air in polycrystalline form by solid-state reaction. These materials have been studied by X-ray powder diffraction (XRPD), neutron powder diffraction (NPD) and magnetic susceptibility. The structural refinement was performed from combined XRPD and NPD data (D2B instrument, λ=1.594 Å). At room temperature, the replacement of Sr²⁺ by La³⁺ induces a change of the tetragonal structure, space group I4/m of the undoped Sr₂CoWO₆ into the distorted monoclinic crystal structure, space group P2₁/n, Z=2. The structure of La-doped phases contains alternating CoO₆ and (Co/W)O₆ octahedra, almost fully ordered. On the other hand, the replacement of Sr²⁺ by La³⁺ induces a partial replacement of W⁶⁺ by Co²⁺ into the B sites, i.e. Sr_2−xLa_xCoW_1−yCo_yO₆ (y=x/4) with segregation of SrWO₄. Magnetic and neutron diffraction measurements indicate an antiferromagnetic ordering below T_N=24 K independently of the La-substitution.     

Synthesis and structural study of a new NASICON-type solid solution: Li1−xLax/3Zr2(PO4)3

A new complete solid solution of NASICON-type compounds between LiZr₂(PO₄)₃ and La_1/3Zr₂(PO₄)₃ was evidenced with the general formula Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1). These phases were synthesized by a complex polymerizable method and structurally characterized from Rietveld treatment of their X-ray and neutron powder diffraction data. This solid solution results from the substitution mechanism Li⁺→1/3La³⁺+2/3□ leading to an increase of the vacancies number correlated to an increase of the La content. According to this substitution mechanism, the general formula can then be written Li_1−xLa_x/3□_2x/3Zr₂(PO₄)₃ (0?x?1) in order to underline the correlation between the La content and the vacancies rate. For all the compounds, the structure is clearly related to that of the NASICON family with three crystallographic domains evidenced. For 0?x?0.5, all the members adopt at high temperature the typical NASICON-type structure (s.g. R3¯c), while at lower temperature, their structure distorts to a triclinic form (s.g. C 1¯), as observed for LiZr₂(PO₄)₃ prepared above 1100 °C. Moreover, in this domain, the reversible transition is clearly soft and the transition temperature strongly depends of the x value. For 0.6?x?0.9, the compounds crystallize in a rhombohedral cell (s.g. R3¯), while for x=1, the phase La_1/3Zr₂(PO₄)₃ is obtained (s.g. P3¯, Z=6, a=8.7378(2) Å, c=23.2156(7) Å).This paper is devoted to the structure analysis of the series Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1), from X-ray and neutron powder thermo diffraction and transmission electron microscopy (TEM) studies.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

Compatibility evaluation between La2Mo2O9 fast oxide-ion conductor and Ni-based materials

The chemical reactivity of La₂NiO_4+δ and nickel metal or nickel oxide with fast oxide-ion conductor La₂Mo₂O₉ is investigated in the annealing temperature range between 600 and 1000 °C, using room temperature X-ray powder diffraction. Within the La₂NiO_4+δ/La₂Mo₂O₉ system, subsequent reaction is evidenced at relatively low annealing temperature (600 °C), with formation of La₂MoO₆ and NiO. The reaction is complete at 1000 °C. At reverse, no reaction occurs between Ni or NiO and La₂Mo₂O₉ up to 1000 °C. Together with a previous work [G. Corbel, S. Mestiri, P. Lacorre, Solid State Sci. 7 (2005) 1216], the current study shows that Ni-CGO cermets might be chemically and mechanically compatible anode materials to work with LAMOX electrolytes in solid oxide fuel cells.     

Evolution and characterization of fluorite-like nano-SrBi2Nb2O9 phase in the SrO-Bi2O3-Nb2O5-Li2B4O7 glass system

Transparent glasses of various compositions in the system (100−x)Li₂B₄O₇−x(SrO-Bi₂O₃-Nb₂O₅) (where x=10, 20, 30, 40, 50 and 60, in molar ratio) were fabricated via splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses. X-ray powder diffraction (XRD) and transmission electron microscopic studies confirmed the amorphous nature of the as-quenched and crystallinity in the heat-treated samples. Fluorite phase formation prior to the perovskite SrBi₂Nb₂O₉ phase was analyzed by both the XRD and high-resolution transmission electron microscopy. Dielectric and the optical properties (transmission, optical band gap and Urbach energy) of these samples have been found to be compositional dependent. Refractive index was measured and compared with the values predicted by Wemple-Didomemenico and Gladstone-Dale relations. The glass nanocomposites comprising nanometer-sized crystallites of fluorite phase were found to be nonlinear optic active.     

A novel route to synthesize cubic ZrW2−xMoxO8 (x=0-1.3) solid solutions and their negative thermal expansion properties

Cubic ZrW_2−xMo_xO₈ (c-ZrW_2−xMo_xO₈) (x=0-1.3) solid solutions were prepared by a novel polymorphous precursor transition route. X-ray diffraction (XRD) analysis reveals that the solid solutions are single phase with α- and β-ZrW₂O₈ structure for 0?x?0.8 and 0.9?x?1.3, respectively. The optimum synthesis conditions of ZrWMoO₈ are obtained from differential scanning calorimetry-thermal gravimetric analysis (DSC-TGA), XRD and mass loss-temperature/time curves. Following the above experience, the stoichiometric solid solutions of c-ZrW_2−xMo_xO₈ (x=0-1) are obtained within 1 wt% of mass loss. The relationships of lattice parameters (a), phase transition temperatures (T_c) and instantaneous coefficients of thermal expansion (α_i) against the content x of Mo are discussed based on the variation of order degree parameters of ZrW_2−xMo_xO₈.     

A Structural Investigation of La2(GeO4)O and Alkaline-Earth-Doped La9.33(GeO4)6O2

The structures of the oxyorthogermanate La₂(GeO₄)O and the apatite-structured La_9.33(GeO₄)₆O₂ have been refined from powder neutron diffraction data. La₂(GeO₄)O crystallizes in a monoclinic unit cell (P2₁/c) and is cation stoichiometric in contrast to previous reports. La_9.33(GeO₄)₆O₂ crystallizes in a hexagonal unit cell (P6₃/m) and the powder diffraction data show anisotropic peak broadening that is observed in electron diffraction patterns as incommensurate diffuse spots at hkq reciprocal planes (with q=1.6-1.7) and can be attributed to a correlated disorder in the “apatite channels”. This compound was doped up to a nominal composition close to M₂La₈(GeO₄)₆O₂ with M=Ca, Sr, Ba. The dopant ions preferentially occupy the 4f sites as the number of La vacancies decreases. The measured ionic conductivity of La_9.33(GeO₄)₆O₂ is about 3 orders of magnitude larger than for La₂(GeO₄)O at high temperatures and decreases with increasing dopant content from the highest value of about 0.16 S cm⁻¹ at 1160 K.     

Crystal chemistry of Co-doped Zn7Sb2O12

Zn₇Sb₂O₁₂ forms a full range of Co-containing α solid solutions, Zn_7−xCo_xSb₂O₁₂, with an inverse-spinel structure at high temperature. At low temperatures for x<2, the solid solutions transform into the low temperature β-polymorph. For x=0, the β→α transition occurs at 1225±25 °C; the transition temperature decreases with increasing x. At high x and low temperatures, α solid solutions are formed but are non-stoichiometric; the (Zn+Co):Sb ratio is >7:2 and the compensation for the deficiency in Sb is attributed to the partial oxidation of Co²⁺ to Co³⁺. From Rietveld refinements using ND data, Co occupies both octahedral and tetrahedral sites at intermediate values of x, but an octahedral preference attributed to crystal field stabilisation, causes the lattice parameter plot to deviate negatively from the Vegard's law. Sub-solidus compatibility relations in the ternary system ZnO-Sb₂O₅-CoO have been determined at 1100 °C for the compositions containing ?50% Sb₂O₅.     

Transition metal tetramolybdate dihydrates MMo4O13·2H2O (M=Co,Ni) having a novel pillared layer structure

Hydrothermal synthesis in the M/Mo/O (M=Co,Ni) system was investigated. Novel transition metal tetramolybdate dihydrates MMo₄O₁₃·2H₂O (M=Co,Ni), having an interesting pillared layer structure, were found. The molybdates crystallize in the triclinic system with space group P−1, Z=1 with unit cell parameters of a=5.525(3) Å, b=7.058(4) Å, c=7.551(5) Å, α=90.019(10)°, β=105.230(10)°, γ=90.286(10)° for CoMo₄O₁₃·2H₂O, and a=5.508(2) Å, b=7.017(3) Å, c=7.533(3) Å, α=90.152(6)°, β=105.216(6)°, γ=90.161(6)° for NiMo₄O₁₃·2H₂O The structure is composed of two-dimensional molybdenum-oxide (2D Mo-O) sheets pillared with CoO₆ octahedra. The 2D Mo-O sheet is made up of infinite straight ribbons built up by corner-sharing of four molybdenum octahedra (two MoO₆ and two MoO₅OH₂) sharing edges. These infinite ribbons are similar to the straight ones in triclinic-K₂Mo₄O₁₃ having 1D chain structure, but are linked one after another by corner-sharing to form a 2D sheet structure, like the twisted ribbons in BaMo₄O₁₃·2H₂O (or in orthorhombic-K₂Mo₄O₁₃) are.     

Synthesis, characterization, and structure determination of the orthorhombic U2(PO4)(P3O10)

β-UP₂O₇ has been synthesized under hydrothermal conditions (θ=500°C, P=200 MPa), using UO₂ and H₃PO₄. β-UP₂O₇ crystallizes in the orthorhombic space group Pn2₁a, with a=11.526 (2) Å, b=7.048 (2) Å, c=12.807 (2) Å and Z=4. Its structure has been determined through direct methods and difference Fourier synthesis and has been refined to R=0.0396. The structure is built on UO₈ polyhedral chains along the b-axis. PO₄³⁻ and P₃O₁₀⁵⁻ groups coexist in the structure and the latter groups form non-linear chains. Cohesion of the structure is made through the linkage of UO₈ chains by PO₄ and P₃O₁₀ groups leading to the formula U₂(PO₄)(P₃O₁₀) instead of β-UP₂O₇. Vibrational and optical spectra confirm the results obtained by X-ray diffraction. DTA-TGA measurements show that the transformation of U₂(PO₄)(P₃O₁₀) to the cubic α-UP₂O₇ occurs at θ=870°C.     

Pt2Mo3N and PdPtMo3N: new interstitial nitrides prepared from freeze-dried precursors

The molybdenum bimetallic and trimetallic nitrides Pt₂Mo₃N and PdPtMo₃N have been synthesized by ammonolysis of the stoichiometric amorphous precursor, obtained by freeze drying of aqueous solutions of the appropriate metal salts. These compounds have been characterized by elemental analysis, energy-dispersive analysis of X-rays, X-ray diffraction, scanning electron microscopy, transmission electron microscopy and thermogravimetry analysis under an oxygen atmosphere. Pt₂Mo₃N and PdPtMo₃N crystallize in the cubic space group P4₁32 (213), with lattice parameters of a=6.83586(4) and 6.82542(3) Å, respectively, and form with the unusual filled β-manganese structure. These compounds are stable under air up to 580 K, the oxidation being complete at 910 K.