Study on the influence of cross-sectional area and zeta potential on separation for hybrid-chip-based capillary electrophoresis using 3-D simulations

Hybrid chips combing microchips with capillaries have displayed particular advantages in achieving UV-vis and mass spectroscopic detection. In this work, systematic 3-D numerical simulations have been carried out to explore the influence of junction interface cross-sectional area and ζ-potential distribution on sample band broadening in hybrid-chip electrophoresis separation. In this case, the ratio of cross-sectional area of chip to capillary channel (S(ratio) ) is used as the parameter of the variation in junction interface cross-sectional area. Theoretical simulations demonstrated that the decrease of the S(ratio) would increase the separation efficiency in the hybrid-chip-based CE with uniform ζ-potential distribution. ζ-potential distribution along the axial direction of the channel also affects mass transport in hybrid-chip-based CE. Therefore, the effect of ζ-potential distribution has been considered in the 3-D simulation. Theoretical simulation results reveal that ζ-potential distribution rather than the interface cross-sectional area variation (S(ratio) ) controls the sample band broadening and manipulates sample separation efficiency in the hybrid-chip-based CE with non-uniform ζ-potential distribution. Both the theoretical simulations and experimental results show that optimal hybrid-chip CE separation efficiency can be achieved at S(ratio) =1.     

Combination of flow injection with capillary electrophoresis: 8. Miniaturized capillary electrophoresis system with flow injection sample introduction and electrogenerated chemiluminescence detection

The combined flow injection (FI)-capillary electrophoresis (CE) system was further exploited by coupling to an electrogenerated chemiluminescence (ECL) detection system. A low-cost miniaturized CE system was developed on a chip platform to provide easy interface both with FI sample introduction and with ECL detection. A falling-drop interface was employed to perform FI split-flow sample introduction while achieving electrical isolation from the CE high voltage. A plexiglas reservoir at the capillary outlet served as both the reaction and detection cell for the ECL reaction, with Ru(bpy)₃²⁺ reagent continuously flowing through the cell. An optical fiber was positioned within the reservoir close to the capillary outlet for transferring the ECL emission to the PMT. The relative positions of the capillary outlet, working electrode and optical fiber as well as reagent renewal flow-rate were optimized to achieve both good sensitivity and separation efficiency under non-interrupted sampling conditions, involving large numbers of samples. An on-column joint often used in other works for isolating the ECL detection system from the CE separation voltage was not found necessary. The performance of the system was illustrated by the baseline separation of proline, valine and phenylalanine with a high throughput of 50 h⁻¹ and plate height of 14 μm for proline under 147 V cm⁻¹ field strength. Detection limits (3σ) were 1.2, 50 and 25 μM and peak height precisions were 1.4, 5.4 and 4.3% R.S.D. (n=9) for proline, valine and phenylalanine, respectively.     

On-column detection of multiphoton-excited fluorescence in CE using hyphenated cylindrical-square capillaries

Multiphoton-excited fluorescence (MPEF) is a complementary and useful mode of LIF detection in CE with advantages of ultra-low mass detectability and spectral excitability, but it is currently quite limited by its end-column configuration. In this article, we demonstrate a novel strategy of on-column schemes that can greatly facilitate MPEF detection in CE. FITC-labeled amine species were used as the model samples for the evaluation and comparison of those detection scenarios. By using the square capillary instead of the conventional cylindrical one, the on-column MPEF could be readily achieved, with detection sensitivity of 0.72 microM that was comparable with the end-column mode. However, this strategy unfavorably reduced separation efficiency. The theoretical plate number on averaging all the sample peaks was significantly decreased from 283,000 to 19,000/m. To minimize such an influence, a short square capillary acting as an on-column MPEF detection cell was then mounted to a long cylindrical capillary responsible for the CE separation. Results indicated that both high separation efficiency (240,000/m) and better detectability (0.42 microM) were realized simultaneously by using this binary-capillary configuration. Quantitative analysis was performed under the optimized detector configuration and revealed a linear dynamic range of 2 orders of magnitude, with mass detection limit down to the mid-yottomole level.     

Comprehensive two-dimensional separations based on capillary high-performance liquid chromatography and microchip electrophoresis

A novel comprehensive two-dimensional (2-D) separation system coupling capillary high-performance liquid chromatography (cHPLC) with microchip electrophoresis (chip CE) is demonstrated. Reversed-phase cHPLC was used as the first dimension, and chip CE acted as the second dimension to perform fast sample transfers and separations. A valve-free gating interface was devised simply by inserting the outlet-end of LC column into the cross-channel on a specially designed chip. A home-made confocal laser-induced fluorescence detector was used to perform on-chip high-sensitive detection. The cHPLC effluents were continuously delivered to the chip and pinched injections of the effluents every 20 seconds were employed for chip CE separation. Gradient elution of cHPLC was carried out to obtain the high-efficiency separation. Free-zone electrophoresis was performed with triethylamine buffer to achieve high-speed separation and prevent sample adsorption. Such a simple-made comprehensive system was proved to be effective. The relative standard deviations for migration time and peak height of rhodamine B in 150 sample transfers were 3.2% and 9.8%, respectively. Peptides of the fluorescein isothiocyanate (FITC)-labeled tryptic digests of bovine serum albumin were fairly resolved and detected with this comprehensive 2-D system.     

Toward million-fold sensitivity enhancement by sweeping in capillary electrophoresis combined with thermal lens microscopic detection using an interface chip

This paper reports a thermal lens microscope (TLM) detection coupled with capillary electrophoresis (CE) by using an interface chip (IFChip) to achieve highly sensitive detection with high reproducibility. Fused silica capillaries with an inner diameter of 50 microm were directly connected to a microchannel on the IFChip. In comparison with an on-capillary detection method in CE-TLM, ca. 10-fold improvements in the reproducibility for peak height were obtained by using IFChips. The detection limit of an azo dye was estimated to be 3.6 x 10(-7)M (100 ppb), which was above 100-times lower than that of conventional absorbance detection. Toward further improvement of the detectability for nonfluorescent compounds, on-line sample preconcentration by sweeping was applied to the CE-TLM using the IFChip. Due to the sweeping effect, 3900000-fold increase in the sensitivity was successfully achieved.     

An on-column fracture/end-column reaction interface for chemiluminescence detection in capillary electrophoresis

Chemiluminescence (CL) offers a sensitive detection method for capillary electrophoresis (CE), but the implementation of CE–CL is usually under compromised operating conditions for CE, such as the prerequisite of extreme pH buffer for optimal CL reaction at the capillary outlet. This has sometimes significantly deteriorated the separation of CE. In this study, the development of a new interface makes it possible to optimize the operating conditions for CE separation and CL detection independently. The interface consists of an on-column fracture being installed in a reservoir near the capillary end to create an electrical connection and also serve as reagent addition entrance. The capillary terminal is inserted into an end-column reservoir for CL reaction and detection. In this arrangement, the applied electric field has been decoupled from the CL detection, which is proved to effectively improve CE's performance by allowing the use of optimal CE buffers. At the same time, it enables the optimization of CL detection independently. The applicability of this interface was evaluated by using acridinium ester (AE) and luminol systems. For AE system, the interfering products of CL reagent (⁻OH, HO₂⁻) have been prevented, and the pH range of CE buffer can be independent to the optimal pH value of AE CL reaction, which is usually below 3. The AE was detected using running buffer at pH 8.7, giving a detection limit of 0.1 nM (S/N = 3), and the theoretical plate numbers is as high as 56 000. The on-column fracture based configuration is simple, sensitive and easy to implement.     

Efforts to improve detection sensitivity for capillary electrophoresis coupled to atmospheric pressure photoionization mass spectrometry

Electrospray ionization performs best with volatile buffers. However, generally the best separation performance for capillary electrophoresis (CE) is achieved with non‐volatile buffers. Hyphenation of CE with mass spectrometry (MS) utilizing atmospheric pressure photoionization (APPI) enables use of a wider range of separation buffers without compromising detection sensitivity. As APPI is considered to be mass flow sensitive, the use of a larger inner diameter separation capillary (75 µm) allows larger volumes to be injected, without decreased separation performance, thus providing improved sensitivity (approx. a factor of 10), compared to the use of a 25 µm capillary. However, nebulizing gas flow and position of capillary tip in the sprayer have to be carefully optimized to prevent excessive band broadening. Further improvement in sensitivity (approx. a factor of 2) was obtained by decreasing the distance between the sprayer and ionization region, indicating that a specially designed CE/APPI‐MS interface for low flow rates will be favourable. Copyright © 2010 John Wiley & Sons, Ltd.     

Effects of nebulizing and drying gas flow on capillary electrophoresis/mass spectrometry

This study was focused on examining the influence of gas flow parameters on capillary electrophoresis/mass spectrometry (CE /MS) performance using sheath-liquid CE /MS interfaces. The effects of nebulizing and drying gas velocity and drying gas temperature on CE separation and MS detection sensitivity were systematically determined. Nebulizing gas velocity was observed to be a critical parameter in the optimization of CE /MS method, since it affected both MS detection sensitivity, and also CE separation efficiency for one interface design tested. Better detection sensitivity was obtained when the nebulizing gas velocity was increased. However, high velocity of the nebulizing gas flow can cause a hydrodynamic bulk flow inside the CE capillary, thus clearly increasing the apparent mobility and decreasing the resolution obtained for the compounds studied. Increasing the drying gas velocity or temperature did not affect the apparent mobility or the separation efficiency and the temperature could be increased to achieve the optimal detection sensitivity in the CE /MS analysis. For comparison, the effects of nebulizing gas flow were studied using a different design of the coaxial sheath-liquid CE /MS interface, and in this case better detection sensitivity but no effect on CE separation efficiency was observed with increased nebulizing gas velocity. These different effects of nebulizing gas flow on the CE bulk flow were concluded to result from pressure differences at the tip of the CE capillaries for the different CE /MS interface arrangements. It is therefore recommended that the cross-sectional dimensions of the fused-silica and steel capillaries, and the gas streamlines, should be optimized when CE /MS interfaces are built. Moreover, the effect of gas flow on CE separation should be studied when optimizing the CE /MS operation parameters.     

A novel sheathless interface for capillary electrophoresis/electrospray ionization mass spectrometry using an in-capillary electrode

A simple and rugged sheathless interface for capillary electrophoresis/electrospray ionization-mass spectrometry (CE/ESI-MS) was designed using common laboratory tools and chemicals. The interface uses a small platinum (Pt) wire that is inserted into the CE capillary through a small hole near the terminus. The position of the wire inside the CE capillary and within the buffer solution is analogous to standard CE separation operations where the terminus of the CE capillary is placed inside a buffer reservoir along with a grounded platinum electrode. By combining the use of the in-capillary electrode interface with sharpening of the fused silica tip of the CE capillary outlet, a stable electrospray current was maintained for an extended period of time. The design was successfully applied to CE/ESI-MS separations and analysis of mixtures of peptides and proteins. A detection limit of approximately 4 femtomole (S/N = 3) was achieved for detection of myoglobin utilizing a 75-µm-i.d. aminopropylsilane treated CE column and using a wide scan range of 550–1300 Da. The advantages of this new design include (1) a stable CE and ESI current, (2) durability, (3) a reduced risk of sparking between the capillary tip and the inlet of the mass spectrometer, (4) lack of any dead volume, and (5) facile fabrication with common tools and chemicals.     

Chip-based capillary electrophoresis with an electrodeless nanospray interface

A sheathless and electrodeless nanospray interface has been used to interface a polycarbonate capillary electrophoresis (CE) chip to a mass spectrometer (MS). The chip was made of two flat polycarbonate plates which were bolted together. Channels were imprinted in one of the plates with metal wires, using a hydraulic press. A short tapered capillary connected to the chip was used as the nanospray emitter. The advantage of this electrodeless interface is that it was not necessary to apply a electrospray voltage to the chip or the nanospray emitter. Instead, the CE voltage already applied to the buffer compartment on the chip, to drive the electrophoresis, was used to generate the spray also. A low conductivity buffer of 1.25 mmol/L ammonium acetate in 80% methanol was used to obtain a large electric field across the buffer channel. The performance of the device was evaluated by analyzing a mixture of three beta-agonists Relative standard deviation (RSD) values obtained were between 4.8 and 5.0%. A sample concentration of 40 nmol/L resulted in a signal-to-noise ratio of 2 to 5 for the different components. Compared to a conventional CE analysis in a fused silica capillary with UV detection, only a minor loss of resolution was observed, which can be attributed to the design of the chip.     

21世纪毛细管电泳技术及应用发展趋势

在21世纪，毛细管电泳技术面临着新的挑战和机遇，在其检测手段，仪器的小型化和集成化，以及分离模式上都存在着极大的发展空间，文中针对这三方面的发展趋势和毛细管电泳的应用进行了讨论。     

A sheathless poly(methyl methacrylate) chip-CE/MS interface fabricated using a wire-assisted epoxy-fixing method

Using a wire-assisted epoxy-fixing method, a sheathless CE/MS interface on a poly-(methyl methacrylate) (PMMA) CE chip has been developed. The sheathless chip-CE/MS interface utilized a tapered fused-silica tip and the electrical connection was achieved through a layered coating of conductive rubber. The wire-assisted method provided facile alignment of channels between the PMMA CE chip and an external capillary sprayer without the need for micromachining. Because the wire was in the channel during fixing, the risk of channel blockage by the epoxy was avoided. This chip CE device has minimal dead volume because the interstitial spaces were filled by a fast-fixing epoxy resin. The performance of the chip-CE-ESI-MS device was demonstrated with the analysis of peptide mixtures.     

Separation of Compounds in Traditional Chinese Medicines Using Comprehensive Two Dimensional Chromatography

Traditional Chinese medicine is an invaluable treasure of the Chinese nationalities. Thousands of natural species that are of pharmaceutical importance have been accumulated. Most of them are plants. Traditional Chinese medicines generally are of unusual complexity. Even a single medicinal material may contain hundreds of compounds. Since these compounds play cooperative roles pharmacologically, it is essential to analyze all compounds as a whole. It is also important for quality controls in each step of productions, such as raw material collection, processing, and manufacturing. A comprehensive two-dimensional separation system coupling capillary high performance liquid chromatography with fast capillary electrophoresis (μ-HPLC-CE) is developed to provide a powerful means to separate such complex samples. In the first dimensional separation, a home-packed micro-HPLC column was used to reduce the consultation of sample injection and avoid sample dilution. The second dimensional analysis was carried out by micellar electrokinetic chromatography(MEKC) considering the fact that most compounds in Chinese medicine are neutrals. In order to achieve high-speed separation^ theory of fast MEKC was extensively studied. Models of the fast MEKC migration behaviors were established. Relationships of theoretical plates vs. electric field strength and column length were derived. It is concluded that maintaining certain column length and applying high-voltage at the ends of the capillary simultaneously are the key points to achieving fast MEKC separation. A pulse-contacting interface was developed for the 2-D μ-HPLC-CE system. CE sampling was carried out in an instant contact of HPLC and CE columns in an optimized timing program. During the short contact period, a certain fraction of HPLC effluent was introduced into the CE capillary. Injection efficiency for such an interface was up to 81%. Relative standard deviation (RSD) of migration times and peak heights for 100 consecutive MEKC. separation were 3.0% and 1.8%, respectively. With this novel 2-D μ-HPLC-CE system, some traditional Chinese medicines were analyzed and hundreds of peaks were observed. For liquorice, over 110 components were fairly resolved. More than 250 peaks were obtained for a compound mixture of Cheng-Qi-Tang. The peak capacity of this novel comprehensive 2-D HPLC-CE system was estimated to be about 2400 in 80 min.     

Development of a sheathless CE‐ESI‐MS interface

A sheath‐flow interface is the most common ionization technique in CE‐ESI‐MS. However, this interface dilutes the analytes with the sheath liquid and decreases the sensitivity. In this study, we developed a sheathless CE‐MS interface to improve sensitivity. The interface was fabricated by making a small crack approximately 2 cm from the end of a capillary column fixed on a plastic plate, and then covering the crack with a dialysis membrane to prevent metabolite loss during separation. A voltage for CE separation was applied between the capillary inlet and the buffer reservoir. Under optimum conditions, 52 cationic metabolite standards were separated and selectively detected using MS. With a pressure injection of 5 kPa for 15 s (ca. 1.4 nL), the detection limits for the tested compounds were between 0.06 and 1.7 μmol/L (S/N = 3). The method was applied to analysis of cationic metabolites extracted from a small number (12 000) of cancer cells, and the number of peaks detected was about 2.5 times higher than when using conventional sheath‐flow CE‐MS. Because the interface is easy to construct, it is cost‐effective and can be adapted to any commercially available capillaries. This method is a powerful new tool for highly sensitive CE‐MS‐based metabolomic analysis.     

Separation of double-stranded DNA fragments in plastic capillary electrophoresis chips by using E99P69E99 as separation medium.

The separation of double-stranded DNA (dsDNA) fragments in polymethylmethacrylate (PMMA) capillary electrophoresis (CE) chips by using E99P69E99 as a separation medium has been demonstrated. The PMMA CE chips were simply manufactured by micromachining and adhesive tape sealing. To make the separation channel compatible with the separation medium, a dynamic nonionic surfactant coating procedure was developed, which made the plastic separation channel sufficiently hydrophilic to allow the separation medium to fill the channel by capillary action. Subsequent separation of DNA fragments was successful with a separation efficiency of the order of 10(4) theoretical plates over an effective separation distance of 1.5 cm. By using an applied electric field strength of 200 V/cm, the separation of low DNA mass ladder was completed within 5 min. The simple coating procedure, together with the self-assembled viscosity-adjustable separation medium, should be useful to meet some of the essential requirements for developing single-use disposable CE chips. Coating the channels with polymer blends of PMMA and the separation medium also showed promise.     

Focusing and stabilization of bis‐intercalating dye–DNA complexes for high‐sensitive CE‐LIF DNA analysis

Multiple labeling of nucleic acids by intercalative dyes is a promising method for ultrasensitive nucleic acid assays. The properties of the fast dissociation and instability of dye–DNA complexes may prevent from their wide applications in CE‐LIF nucleic acid analysis. Here, we describe an optimum CE focusing method by using appropriately paired sample and separation buffers, Tris‐glycine buffer and Tris‐glycine‐acetic acid buffer. The developed method was applied in both uncoated and polyacrylamide coated fused‐silica capillary‐based CE‐LIF analysis while the sample and separation buffers were conversely used. The complexes of intercalative dye benzoxazolium‐4‐pyridinium dimer and dsDNA were greatly focused (separation efficiency: 1.8 million theoretical plates per meter) by transient isotachophoresis mechanism in uncoated capillary, and moderately focused by transient isotachophoresis in combination of field amplified sample stacking and further stabilized by the paired buffer in polyacrylamide coated capillary. Based on the developed focusing strategy, an ultrasensitive DNA assay was developed for quantitation of calf thymus dsDNA (from 0.02 to 2.14 pM). By the use of an excitation laser power as low as 1 mW, the detection limits of calf thymus dsDNA (3.5 kb) are 7.9 fM in concentration and 2.4×10^?22 mol (150 molecules) in mass. We further demonstrate that the non‐gel sieving CE‐LIF analysis of DNA fragments can be enhanced by the same strategy. Since the presented strategy can be applied to uncoated and coated capillaries and does not require special device, it is also reasonable to extend to the applications in chip‐based CE DNA analysis.     

Optimization of capillary electrophoretic-electrospray ionization-mass spectrometric analysis of catecholamines

The capillary electrophoretic-mass spectrometric analysis (CE-MS) of catecholamines was optimized with coaxial sheath flow interface and electrospray ionization (ESI). The parameters studied included the sheath liquid composition and its flow rate, separation conditions in ammonium acetate buffer together with the ESI and cone voltages as mass spectrometric parameters. In addition, the effect of ESI voltage on injection as well as the siphoning effect were considered. The optimized conditions were a sheath liquid composition of methanol-water (80:20 v/v) with 0.5% acetic acid, with a flow rate of 6 microL/min. The capillary electrophoretic separation parameters were optimized with 50 mM ammonium acetate buffer, pH 4.0, to +25 kV separation voltage together with a pressure of 0.1 psi. The most intensive signals were obtained with an ESI voltage of +4.0 kV and a cone voltage of +20 V. The nonactive ESI voltage during injection as well as avoidance of the siphoning effect increased the sensitivity of the MS detection considerably. The use of ammonium hydroxide as the CE capillary conditioning solution instead of sodium hydroxide did not affect the CE-MS performance, but allowed the conditioning of the capillary between analyses to be performed in the MS without contaminating the ion source.     

粒子群算法优化中药化学成分的毛细管电泳分离条件

建立了一种基于粒子群优化算法的毛细管电泳条件辅助优化方法。以丹参为研究对象,将改良的色谱指数方程用于评价酚酸类成分的电泳分离性能,用粒子群优化算法对分离条件进行全局寻优,获得最佳的区带电泳分离条件(5.0 mmol/L硼砂,18.5 mmol/L磷酸二氢钠,6.1%乙腈,运行电压18.2 kV)。为进一步改善分离,在所获优化条件下添加50.0 mmol/L SDS,在胶束电动毛细管色谱分离模式下使酚酸类成分(原儿茶醛、丹参素、丹酚酸B等)得到更好分离。本方法准确可靠,可推广应用于其他复杂化学体系的毛细管电泳分离条件优化。     

Capillary zone electrophoresis and capillary electrophoresis-mass spectrometry for analyzing qualitative and quantitative variations in therapeutic albumin

The present study describes a reproducible and quantitative capillary zone electrophoresis (CZE) method, which leads to the separation of nine forms (native, oxidized and glycated) of human serum albumin (HSA). In an attempt to identify the different species separated by this CZE method, the capillary electrophoresis was coupled to mass spectrometry using a sheath liquid interface, an optimized capillary coating and a suitable CE running buffer. CE-MS analyses confirmed the heterogeneity of albumin preparation and revealed new truncated and modified forms such as Advanced Glycation End products (AGEs). Assignment of the CZE peaks was carried out using specific antibodies, carboxypeptidase A or sample reduction before or during the CE separation. Thus, five HSA forms were unambiguously identified. Using this CZE method several albumin batches produced by slightly different fractionation ways could be discriminated. Furthermore, analyses of HSA preparations marketed by five pharmaceutical industries revealed that two therapeutic albumins, including that marketed by LFB, contained the highest proportion of native form and lower levels of oxidized forms.     

无死体积蚀刻多孔膜接口的制作及其在二维毛细管电泳分离系统中的应用

介绍了一种在毛细管柱上原位腐蚀而成的多孔膜接口的制作方法,并用该接口构建了一类毛细管电泳二维分离技术平台。柱上原位腐蚀刻成的多孔膜接口具有零死体积、制作过程简易、成本低廉、耐用、柱间切换便捷等优点,特别适合作为基于毛细管柱的二维及多维电泳联用中的接口,是目前二维及多维毛细管柱联用中一类较为新型、实用、理想的接口。以鹿茸冻干粉可溶物样品为例,验证了该接口在二维毛细管电泳联用系统中的可行性和分离效能。实验结果表明：鹿茸冻干粉可溶物整个二维分离分析的时间在1 h内完成,二维分离系统的分辨率和总峰容量都比一维的高。