Robust solvent‐free fabrication and characterization of (polydimethylsiloxane‐co‐2‐hydroxyethylmethacrylate)/poly (ethylene glycol) methacrylate (PDMS‐HEMA)/PEGMA hydrogels

Combining hydrophobic materials such as polydimethylsiloxane (PDMS), a natural hydrophobic material with typical hydrophilic monomers without using organic solvent remains a big challenge due to their extreme different properties; hence, fabricating a class of silicone hydrogels with two extremes without use of organic solvents could bring us a novel class of silicone hydrogels. Herein, a range of PDMS‐HEMA‐PEGMA hydrogels was prepared from hydroxyl‐terminated PDMS, 2‐hydroxyethylmethacrylate (HEMA), poly (ethylene glycol) methacrylate (PEGMA), and isophorone diisocyanate via condensation and radical copolymerization reactions. The infrared results confirmed the PDMS‐HEMA‐PEGMA network formation, while the hydrophilicity of the as‐prepared block copolymer was dependent on (PDMS‐HEMA)/PEGMA ratio. Increasing the PEGMA content resulted in increased equilibrium water content, phase separation, surface roughness, and tensile strength, while the tensile modulus, elongation at break, optical transmittance, water contact angle, and oxygen permeability (Dk) were decreasing. At PEGMA content of 28.3%, the relative protein adsorption ratio decreased to 20% and 36% for bovine serum albumin and lysozyme, respectively, compared with that of the control (PDMS‐HEMA), suggesting antiprotein adsorption ability. In overall, the results showed that the PDMS‐HEMA‐PEGMA hydrogels not only exhibited remarkable hydrophilicity and suppressed protein adsorption but also maintained higher optical transparency and oxygen permeability (Dk).     

Study of hydrophilicity and stability of chemically modified PDMS surface using piranha and KOH solution

Successful realization of various BioMEMS devices demands effective surface modification techniques of PDMS elastomer. This paper presents a detailed report on a simple and cost effective approach for surface modification of PDMS films involving wet chemical treatment in two‐step processes: primarily involving piranha solution followed by KOH dip to improve hydrophilicity and stability of PDMS surface. Chemical composition of the solution and surface treatment condition have been varied and optimized to significantly increase the surface energy. The effect of surface modification of the elastomer after wet chemical treatment is analyzed using contact angle measurement and FTIR‐ATR study. PDMS surface treated in piranha solution with H₂O₂ and H₂SO₄ in the ratio of 2:3 followed by a dip in KOH solution for 15 min duration each, demonstrated a maximum reduction of contact angle to ～27° as compared to untreated sample having a contact angle of ～110°. The removal of hydrophobic methyl group from elastomer surface and subsequent hydrophilization of surface by wet chemical process was confirmed from FTIR‐ATR spectra. This result is also supported by improved adhesion and electrical continuity of deposited aluminum metal film over the modified PDMS surface. Copyright © 2011 John Wiley & Sons, Ltd.     

A Photocatalytically Active Lubricant‐Impregnated Surface

Lubricant impregnated surfaces (LISs) exhibit sliding angles below 5°. A LIS is presented that possesses photocatalytic activity as well as improved liquid repellency. In a single‐step reaction, the surface of photocatalytic mesoporous TiO₂ substrate is modified by grafting polydimethylsiloxane (PDMS) brush and the residual non‐bound PDMS serves as lubricant. Since the lubricant and the hydrophobic layer are chemically identical, the grafting PDMS layer is stably swollen by the lubricant PDMS, which inhibits direct contact of liquid drops to the solid substrate. Liquid drops such as water, methanol, and even low‐surface‐tension fluorocarbons, slide on the surface with tilt angles below 1°. The surface exhibits long‐term stable photocatalytic activity while retaining its liquid repellency. This photocatalytic activity allows photocatalytic chemistry, for example, decomposition of organics, on LIS to be carried out.     

Flexible superhydrophobic gold film for magnetical manipulation of droplets

Herein, we present a simple, efficient, and economical approach for the preparation of superhydrophobic gold film embedded on polydimethylsiloxane (PDMS) sheets without the requirement of surface pretreatment. The reduction reaction between chloroauric acid (HAuCl₄) and sodium formate (HCOONa) at room temperature was performed to generate the aggregated gold microstructures on a PDMS sheet without chemical residuals. Superhydrophobic property was achieved when deposition time was reached to 2 h with water contact angle >160° and low contact angle hysteresis (H = 1.93°). Systematic investigations of the size, morphology, and mechanism of the generated gold films are presented. The generated gold film contains two different layers involving uniform spherical gold particles attached to the PDMS surface with the complex hierarchical structures on top. The complex structures play an important role in the superhydrophobic property, as they strongly promote the roughness to the PDMS surface. The durability of the fabricated gold film was elucidated by dropping ~7,200 waterdrops and external physical forces (e.g. stretch, bend, and twist). The main structures and their superhydrophobic properties have not disoriented after the tests. Moreover, the surface of the gold film demonstrated the potential applications as magnetical manipulation of droplets and a robust Surface enhanced Raman spectroscopy (SERS substrate).     

拒水型有机硅改性聚氨酯嵌段共聚物的合成与表征

以氨丙基硅氧烷偶联剂和端羟基聚二甲基硅氧烷(PDMS)为原料,合成了端氨丙基聚二甲基硅氧烷低聚物(SN2),并将其作为扩链剂,制备了有机硅-聚氨酯(Si-PU)嵌段共聚物.考察了聚氨酯预聚体的加料比(rNCO/OH)、SN2与聚氨酯预聚体的加料比(rNH2/NCO)对Si-PU嵌段共聚物溶液流变行为及其膜性能的影响.研究发现,该Si-PU共聚物的异丙醇溶液呈现较低的表观黏度及牛顿特性;成膜时,有机硅链段向表面迁移;膜表面对水的接触角达110°以上,且随着有机硅链段含量的增高而增大;共聚物膜的24 h吸水率较低(<1.5 wt%);但当有机硅链段含量过高时,吸水率反而增高.     

Laser induced surface modification of polydimethylsiloxane as a super-hydrophobic material

In order to render the surface of polydimethylsiloxane (PDMS) super-hydrophobic without changing its bulk properties, a PDMS film without photosensitizer was exposed to CO₂ pulsed laser, at room temperature, as the excitation source. The modified surfaces have been studied by performing scanning electron microscopy (SEM) combined with energy dispersive X-ray analysis (EDXA) and attenuated total reflectance infrared (ATR-IR) spectroscopy. To evaluate the surface property, the water drop contact angle was measured. The dependence of ---Si---O---Si infrared peak intensity, O/Si ratio and water drop contact angle of the treated PDMS as a function of the number of laser pulses were studied. SEM micrographs and water drop contact angle variations show the uniform porosity and super-hydrophobic nature on the surface of PDMS. ATR-FTIR spectra show that the modified PDMS surface contains carbonate groups which enriched the oxygen content of the surface. EDXA analysis shows a higher percentage of oxygen on the surface of the modified PDMS. The hydrophobicity of the samples was found to depend upon the number of laser pulses, but with significant variation between the treated samples. The bulk mechanical properties of PDMS after being laser-treated did not change as shown by dynamic mechanical thermal analysis (DMTA).     

Au@PS纳米颗粒掺杂PDMS/(PVDF-TrFE)复合薄膜的制备及介电-疏水性能

结合乳液聚合和还原法在250 nm的聚苯乙烯(PS)微球表面均匀负载了Au纳米颗粒. 通过溶液共混法, 使Au@PS纳米颗粒与聚二甲基硅氧烷(PDMS)/聚偏氟乙烯-三氟乙烯[P(VDF-TrFE)](质量比为2∶3)均匀混合, 制备出结构致密、 Au@PS均匀分布的微突起的复合薄膜. 研究了不同Au@PS纳米颗粒掺杂量对复合薄膜的结构、 熔融结晶行为和介电疏水特性的影响. 研究发现, Au@PS纳米颗粒的引入阻碍了P(VDF-TrFE)的β相的产生, 但对PDMS/P(VDF-TrFE)复合薄膜的化学健结构没有显著影响; 随着Au@PS纳米颗粒含量的增多, 复合薄膜结晶温度和玻璃化转化温度升高, 熔点略有降低. 由于界面极化和微电容效应协同作用, 掺杂Au@PS复合薄膜的介电常数有显著提升. PS球表面均匀负载的Au纳米颗粒减少了导电网络的构成, 使介电损耗维持在较低值. 掺杂5%(质量分数)Au@PS的复合薄膜介电常数达到22(100 Hz), 分别为纯PDMS和PDMS/P(VDF-TrFE)的8.8倍和3.14倍, 同时具有优异的疏水特性, 接触角达到112.31°.     

Deposition of polysiloxane‐like nanofilms onto an aluminium alloy by plasma polymerized hexamethyldisiloxane: characterization by XPS and contact angle measurements

In this work, aluminium (Alclad 2024‐T3) substrates were cleaned by an r.f. (13.56 MHz) plasma, using argon (Ar), oxygen (O₂) and a mixture of O₂/Ar (50:50) gases. The effectiveness of plasma cleaning was checked in situ using X‐ray photoelectron spectroscopy (XPS) and ex situ using water contact angle measurements. XPS O/Al surface atomic ratios are in excellent agreement with those of the crystalline boehmite and the pseudoboehmite. Oxygen O 1s peak‐fitting was used to quantify the proportion of hydroxyl ions and the functional composition on the aluminium surface: the surface cleaned with O₂ plasma contains 50% of aluminium hydroxides, the ones cleaned with Ar plasma and with Ar/O₂ plasma contain, respectively, 25 and 37% hydroxyl ions. The binding energy separation between Al 2p and O 1s is characteristic of AlO(OH). Thin SiO_x films were subsequently deposited from a mixture of hexamethyldisiloxane (HMDSO) and oxygen. In the absence of oxygen, a hydrophobic (Θ≥ 100° ) film characteristic of polydimethylsiloxane (PDMS) is formed: polysiloxane‐like thinner films (SiO_x) are obtained with the introduction of oxygen. XPS and contact angle measurements confirmed both the composition and the structure of these films. More importantly, contact angle measurements using different liquids and interpreted with the van Oss‐Good‐Chaudhury theory allowed determination of the surface free energy of the deposited films: the calculated values of surface tension of the film formed from HMDSO/O₂: (50/50) are in excellent agreement with those of reference silica‐based materials such as a silicon wafer and cleaned glass. Copyright © 2007 John Wiley & Sons, Ltd.     

Super‐Hydrophobic PDMS Surface with Ultra‐Low Adhesive Force

Summary: Rough polydimethylsiloxane (PDMS) surface containing micro‐, submicro‐ and nano‐composite structures was fabricated using a facile one‐step laser etching method. Such surface shows a super‐hydrophobic character with contact angle higher than 160° and sliding angle lower than 5°, i.e. self‐cleaning effect like lotus leaf. The wettabilities of the rough PDMS surfaces can be tunable by simply controlling the size of etched microstructures. The adhesive force between etched PDMS surface and water droplet is evaluated, and the structure effect is deduced by comparing it with those own a single nano‐ or micro‐scale structures. This super‐hydrophobic PDMS surface can be widely applied to many areas such as liquid transportation without loss, and micro‐pump (creating pushing‐force) needless micro‐fluidic devices.

Etched PDMS surface containing micro‐, submicro‐, and nano‐composite structures shows a self‐cleaning effect with water CA as high as 162° and SA lower than 5°.     

Fabrication of biomimetic superhydrophobic surfaces by a simple flame treatment method

A simple flame treatment method was explored to construct micro/nanostructures on a surface and then fabricate a biomimetic superhydrophobic surface at a relatively low cost. SiO₂‐containing polydimethylsiloxane (PDMS) was used as a substrate. The PDMS replicas with various micropatterned surfaces were fabricated using grass leaf, sand paper, and PET sheet with parallel groove geometry as templates via PDMS replica molding. The PDMS replica surfaces with micron structures and the surface of a flat PDMS sheet as a control sample were further treated by flame. The fabricated surfaces were characterized by scanning electron microscopy and water contact angle measurements. The effect of surface microstructures on the transparency of PDMS was also investigated. The studies indicate that the fine nanoscale structures can be produced on the surfaces of PDMS replicas and a flat PDMS sheet by a flame treatment method, and that the hierarchical surface roughness can be adjusted and controlled by varying the flame treatment time. The flame‐treated surfaces of PDMS replicas and a flat PDMS sheet possess superhydrophobicity and an ultra‐low sliding angle reaching a limiting value of 1°, and the anisotropic wettability of the PDMS replica surface with oriented microgroove structures can be greatly suppressed via flame treatment. The visible light transmittance of the flame‐treated flat PDMS surface decreases with prolonged flame treatment times. Copyright © 2016 John Wiley & Sons, Ltd.     

可粘贴超疏水薄膜的制备

通过聚二甲基硅氧烷(PDMS)与碳纤维织物复合, 采用模板法在PDMS聚合物表面构筑微阵列结构, 制备了一种具有可重复粘贴性的超疏水薄膜. 研究结果表明, 该薄膜微结构表面的接触角为154°, 滚动角为14°, 具有低黏附的超疏水特性. 而PDMS与碳纤维织物的紧密结合, 赋予了超疏水薄膜较高的黏接力和力学性能, 断裂强度达到116.96 MPa. 所制备的超疏水薄膜可粘贴于多种材料表面, 同时经过30 d的长时间粘贴以及50次的循环粘贴后, 该薄膜依然保持着较高的黏附性能及超疏水特征, 表明超疏水薄膜具有良好的力学稳定性及耐久性, 满足长时间可重复使用的要求, 可应用于对破损超疏水涂层的快速、 大面积粘贴修复.     

Surface modification with BSA blocking based on in situ synthesized gold nanoparticles in poly(dimethylsiloxane) microchip

A stable BSA blocking poly(dimethylsiloxane) (PDMS) microchannel was prepared based on in situ synthesized PDMS–gold nanoparticles composite films. The modified microchip could successfully suppress protein adsorption. The assembly was followed by contact angle, charge-coupled device (CCD) imaging, electroosmotic flow (EOF) measurements and electrophoretic separation methods. Contact angle measurements revealed the coated surface was hydrophilic, water contact angle for coated chips was 45.2° compared to a water contact angle for native PDMS chips of 88.5°. The coated microchips exhibited reproducible and stable EOF behavior. With FITC-labeled myoglobin incubation in the coated channel, no fluorescence was observed with CCD image, and the protein exhibited good electrophoretic effect in the modified microchip.     

Specific properties of in situ ruthenium‐catalyzed polyamide 12/polydimethylsiloxane compatibilized blend

The main objective of this work focused on the chemical modification of polyamide 12 (PA12) properties through the reaction with a hydride‐terminated polydimethylsiloxane (PDMS‐SiH). The investigated PA12/PDMS‐SiH blend was compatibilized by ruthenium derivative catalyzed hydrosilylation reaction in molten state. This original route enhanced interfacial adhesion and avoid PDMS‐SiH leaching phenomenon between the two immiscible phases. More specifically, the size of PDMS‐SiH domains in the blend decreased from around 4 μm to 800 nm and from 30 to 1 μm after compatibilization with 10 and 20 wt % PDMS‐SiH, respectively. For the best compatibilized PA12/PDMS‐SiH blend, the introduction of PDMS lowered the surface free energy and the PA12‐based blend turned from hydrophilic to hydrophobic behavior, as evidenced by the water contact angle measurements. Gas permeability and CO₂/H₂ and CO₂/He gas selectivity were also improved with the increase in PDMS content. Besides, the mechanical properties were enhanced with 13% increase in Young's modulus after in situ compatibilization with 15 wt % PDMS‐SiH. Thermal stability was also improved after compatibilization as the initial degradation temperature of reactive blends obviously increased compared with nonreactive ones. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 978–988     

Facile synthesis and responsive behavior of PDMS‐b‐PEG diblock copolymer brushes via photoinitiated “thiol‐ene” click reaction

We present herein a mild and rapid method to create diblock copolymer brushes on a silicon surface via photoinitiated “thiol‐ene” click reaction. The silicon surface was modified with 3‐mercaptopropyltrimethoxysilane (MPTMS) self‐assembled monolayer. Then, a mixture of divinyl‐terminated polydimethylsiloxane (PDMS) and photoinitiator was spin‐coated on the MPTMS surface and exposed to UV‐light. Thereafter, a mixture of thiol‐terminated polyethylene glycol (PEG) and photoinitiator were spin‐coated on the vinyl‐terminated PDMS‐treated surface, and the sequent photopolymerization was carried out under UV‐irradiation. The MPTMS, PDMS, and PEG layers were carefully identified by X‐ray photoelectron spectroscopy, atomic force microscopy, ellipsometry, and water contact angle measurements. The thickness of the polydimethylsiloxane‐block‐poly(ethylene glycol) (PDMS‐b‐PEG) diblock copolymer brush could be controlled by the irradiation time. The responsive behavior of diblock copolymer brushes treated in different solvents was also discussed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Surface characterization of polydimethylsiloxane treated pharmaceutical glass containers by X-ray-excited photo- and Auger electron spectroscopy

The siliconization of pharmaceutical glass containers is an industrially frequently applied procedure. It is done by spreading an aqueous silicone oil emulsion film on the inner surface and successive heat curing treatment at temperatures above 300?°C for 10–30 min. It was often proposed that a covalent bonding of PDMS to the glass or branching of the linear PDMS occurs during heat treatment. The present study was performed for a detailed investigation of the glass and silicone (polydimethylsiloxane = PDMS) chemical state before and after heat-curing treatment and analysis of the bond nature. Combined X–ray excited photoelectron (XPS) and Auger electron spectroscopy as well as angle resolved XPS-measurements were used for analysis of the glass samples. The silicon surface atoms of the borosilicate container glass were transformed to a quartz-like compound whereas the former linear PDMS had a branched, two-dimensional structure after the heat curing treatment. It was concluded that the branching indicates the formation of new siloxane bonds to the glass surface via hydroxyl groups. Further evidence for the presence of bonded PDMS at the glass surface can be found in the valence band spectra of the siliconized and untreated samples. However, this bond could not be detected directly due to its very similar nature to the siloxane bonds of the glass matrix and the organosilicon backbone of PDMS. Due to the high variation of data from the siliconized samples it was concluded, that the silicone film is not homogeneous. Previously raised theories of reactions during heat-curing glass siliconization are supported by the XPS data of this investigation. Yet, the postulation of fixing or baking the silicone on the glass surface is only partially true since the bonded layer is very thin and most of the silicone originally on the surface after heat curing can be removed by suitable solvents. This fraction can therefore still interact with drug products being in contact to the siliconized container wall.     

Surface modification of polydimethylsiloxane with photo-grafted poly(ethylene glycol) for micropatterned protein adsorption and cell adhesion

In this study, we applied photo-induced graft polymerization to micropatterned surface modification of polydimethylsiloxane (PDMS) with poly(ethylene glycol). Two types of monomers, polyethylene glycol monoacrylate (PEGMA) and polyethylene glycol diacrylate (PEGDA), were tested for surface modification of PDMS. Changes in the surface hydrophilicity and surface element composition were characterized by contact angle measurement and electron spectroscopy for chemical analysis. The PEGMA-grafted PDMS surfaces gradually lost their hydrophilicity within two weeks. In contrast, the PEGDA-grafted PDMS surface maintained stable hydrophilic characteristics for more than two months. Micropatterned protein adsorption and micropatterned cell adhesion were successfully demonstrated using PEGDA-micropatterned PDMS surfaces, which were prepared by photo-induced graft polymerization using photomasks. The PEGDA-grafted PDMS exhibited useful characteristics for microfluidic devices (e.g. hydrophilicity, low protein adsorption, and low cell attachment). The technique presented in this study will be useful for surface modification of various research tools and devices.     

Bioactive surface modification of mica and poly(dimethylsiloxane) with hydrophobins for protein immobilization

Bioactive surfaces with appropriate hydrophilicity for protein immobilization can be achieved by hydrophobin II (HFBI) self-assembly on mica and polydimethylsiloxane (PDMS) surfaces. X-ray photoelectron spectroscopy and water contact angle measurements illustrated that the surface wettability can be changed from superhydrophobic (PDMS) or superhydrophilic (mica) to moderately hydrophilic, which is suitable for protein (chicken IgG) immobilization on both substrate surfaces. The results suggest that HFBI assembly, one kind of hydrophobin from Trichoderma reesei, may be a versatile and convenient method for the immobilization of biomolecules on diverse substrates, which may have potential applications in biosensors, immunoassays, and microfluidic networks.     

Simple fabrication of hydrophilic nanochannels using the chemical bonding between activated ultrathin PDMS layer and cover glass by oxygen plasma

This study describes a simple and low cost method for fabricating enclosed transparent hydrophilic nanochannels by coating low-viscosity PDMS (monoglycidyl ether-terminated polydimethylsiloxane) as an adhesion layer onto the surface of the nanotrenches that are molded with a urethane-based UV-curable polymer, Norland Optical Adhesive (NOA 63). In detail, the nanotrenches made of NOA 63 were replicated from a Si master mold and coated with 6 nm thick layer of PDMS. These nanotrenches underwent an oxygen plasma treatment and finally were bound to a cover glass by chemical bonding between silanol and hydroxyl groups. Hydrophobic recovery that is observed in the bulk PDMS was not observed in the thin film of PDMS on the mold and the PDMS-coated nanochannel maintained its surface hydrophilicity for at least one month. The potentials of the nanochannels for bioapplications were demonstrated by stretching λ-DNA (48,502 bp) in the channels. Therefore, this fabrication approach provides a practical solution for the simple fabrication of the nanochannels for bioapplications.     

Biomimetic superhydrophobic and highly oleophobic cotton textiles

We report a biomimetic procedure to prepare superhydrophobic cotton textiles. By in situ introducing silica particles to cotton fibers to generate a dual-size surface roughness, followed by hydrophobization with polydimethylsiloxane (PDMS), normally hydrophilic cotton has been easily turned superhydrophobic, which exhibits a static water contact angle of 155 degrees for a 10 microL droplet. The roll-off angle of water droplets depends on the droplet volume, ranging from 7 degrees for a droplet of 50 microL to 20 degrees for a 7 microL droplet. When a perfluoroalkyl chain is introduced to the silica particle surface, the superhydrophobic textile also becomes highly oleophobic, as demonstrated by a static contact angle of 140 degrees and a roll-off angle of 24 degrees for a 15 microL sunflower oil droplet.     

Easy‐to‐fabricate thin‐film coating on PDMS substrate with super hydrophilicity and stability

With the fast expansion of microfluidic applications, stable, and easy‐to‐fabricate PDMS surface coating with super hydrophilicity is highly desirable. In this study, we introduce a new kind of copolymer‐based, single‐layer thin‐film coating for PDMS. The coating can exist in air at room temperature for at least 6 months without any noticeable deterioration in the super hydrophilicity (water contact angle ～7°), resistance of protein adsorption, or inhibition of the EOF. In addition, this coating enables arbitrary patterning of cells on planar surfaces.