Co-M(M=La,Ce, Fe,Mn, Cu,Cr)复合金属氧化物催化分解N2O

通过共沉淀法制备了一系列Co-M(M= La, Ce, Fe, Mn, Cu, Cr)复合金属氧化物及纯Co3O4催化剂, 考察了其催化分解N2O 的活性. 结果表明在研究的系列催化剂中, Co-Ce 复合氧化物催化剂具有最好的催化分解N2O的活性; 其活性与Ce/Co 摩尔比有直接的关系, 当Ce/Co 摩尔比为0.05 时(CoCe0.05 催化剂)催化活性最佳; 当有NO 和O2共存时, 可能在催化剂活性中心上形成表面硝酸盐或亚硝酸盐吸附物种而使其活性受到较大影响. 通过对Co-M 催化剂的XRD、BET、O2-TPD及H2-TPR 等表征结果的分析, 发现作为主要活性位的Co2+的氧化还原能力是影响催化剂活性的主要原因. 这是因为根据反应机理, N2O 的表面分解步骤与Co2+氧化成Co3+的能力相关, 而吸附氧的脱附与Co3+还原成Co2+的能力相关. 在所研究的催化剂中, 添加除CeO2之外的其它过渡金属氧化物时, 催化剂中Co3+/Co2+的氧化还原能力降低, 因此其催化性能降低. 另外, 添加不同过渡金属氧化物也改变了N2O 催化分解反应的速控步骤.     

V2.1TiNi0.4Zr0.06Cu0.03M0.10 (M=Cr,Co, Fe,Nb, Ta)储氢合金的微结构及电化学性能

采用磁悬浮感应熔炼方法制备了V2.1TiNi0.4Zr0.06Cu0.03M0.10(M=Cr, Co, Fe, Nb, Ta)储氢电极合金, 通过X射线衍射(XRD)、扫描电子显微镜(SEM)、电子衍射能谱(EDS)分析和电化学测试等手段系统研究了添加元素M对合金微结构与电化学性能的影响. 结果表明, 所有合金均由BCC结构的V基固溶体主相和C14型Laves第二相组成, 且第二相沿主相晶界形成三维网状分布; Cr、Nb 和Ta元素主要分布在合金主相中, 而Co和Fe元素主要分布在第二相中. 电化学性能测试表明, 在V2.1TiNi0.4Zr0.06Cu0.03合金中掺加Cr、Co、Fe、Nb或Ta元素后, 虽然会降低最大放电容量, 但能有效抑制合金中V和Ti的腐蚀溶出, 提高电极充放电循环稳定性; 同时还能明显改善合金的高倍率放电性能. 相比之下, V2.1TiNi0.4Zr0.06Cu0.03Cr0.10合金具有最佳的综合电化学性能.     

掺杂纳米TiO2光催化性能的研究

利用浸渍法分别制备了Cr、Mn、Fe、Co、Ni、Cu六种过渡金属离子掺杂改性的二氧化钛光催化剂，以乙酸水溶液的光催化氧化反应和二氧化碳还原反应为探针,评价了掺杂催化剂的光催化性能.借助光电子能谱（XPS）、X射线衍射分析（XRD）等手段对掺杂催化剂进行了表征.研究结果表明，经过渡金属离子掺杂后，光催化性能均有不同程度的改善，改善程度按Cr、Co、Ni、Fe、Mn、Cu递增.掺杂后催化剂表面吸附氧的活泼性、金属离子的价态及得电子能力上的差异决定了不同离子掺杂纳米二氧化钛光催化性能的差异.     

V2.1TiNi0．4Zr0．06Cu0．03M0．10（M=Cr，Co，Fe，Nb，Ta）储氢合金的微结构及电化学性能

采用磁悬浮感应熔炼方法制备了V2.1TiNi0.4Zr0.06Cu0.03M0.10(M=Cr,Co,Fe,Nb,Ta)(M=Cr,Co,Fe,Nb,Ta)储氢电极合金,通过X射线衍射(XRD)、扫描电了显微镜(SEM)、电子衍射能谱(EDS)分析和电化学测试等手段系统研究了添加元素M对合金微结构与电化学性能的影响.结果表明,所有合金均由BCC结构的V基同溶体主相和C14型Laves第二相组成,且第二相沿主相品界形成三维网状分布;Cr、Nb和Ta元素主要分布在合金主相中,而Co和Fe元素主要分布在第二相中.电化学性能测试表明,在V2.1TiNi0.4Zr0.06Cu0.03合金中掺加Cr、Co、Fe、Nb或Ta元素后,虽然会降低最大放电容量,但能有效抑制合金中V和Tj的腐蚀溶出,提高电极充放电循环稳定性;同时还能明显改善合金的高倍率放电性能.相比之下,V2.1TiNi0.4Zr0.06Cu0.03Cr0.10合金具有最佳的综合电化学性能.     

Cp_2M_2(μ-B_4N_4H_8)(M=V,Cr,Mn,Fe)金属多重键成键性质的理论研究

对金属多重键配合物Cp2M2(μ-B4N4H8)(M=V,Cr,Mn,Fe)的结构和成键进行了理论研究,并与Cp2M2(μ-C8H8)进行对比.计算结果表明,在Cp2M2(μ-B4N4H8)基态构型中,B4N4H8配体均以硼为桥原子,金属原子的配位数均为5.其中,Cp2M2(μ-B4N4H8)(M=V,Cr,Mn)基态的结构和成键都与Cp2M2(μ-C8H8)非常接近;而Cp2Fe2(μ-B4N4H8)基态结构与Fe为4配位的Cp2Fe2(μ-C8H8)有所不同.Cp2M2(μ-B4N4H8)(M=V,Cr,Mn,Fe)基态结构分别为含V-V三重键的三态、含Cr-Cr三重键的单态、含Mn-Mn双键的三态及含Fe-Fe单键的单态.     

LaMO3纳米复合钙钛矿氧载体化学循环重整甲烷制合成气

采用溶胶-凝胶法制备了不同B位可变价离子的LaMO3 (M= Cr,Mn,Fe,Co)复合氧化物氧载体,采用X射线衍射、N2吸附-脱附、扫描电镜及CH4程序升温表面反应等手段对氧载体进行了表征,并用于直接选择氧化CH4的反应中.结果表明,Cr,Mn,Fe 和Co均能形成LaMO3纳米复合钙钛矿结构,其氧物种氧化能力大小...     

利用跟踪TPR—GC和XRD技术考察LaNiO3的还原机理

钙钛矿型复合氧化物对许多反应具有较高的催化活性,它们被广泛地用作CO氧化的催化剂.陈水华等对SmMeO_3(Me:V、Cr、Mn、Fe、Co)和Tascon等对LaMeO_3(Me:V、Cr、Mn、Fe、Co、Ni)上CO催化活性评价说明,LnMnO_3和LnCoO_3(Ln=La、Sm)活性最好,而LaNiO_3则表现和LaCoO_3相似活性,由此可推断这些氧化物具有相似的催化性能.本文用TPR-GC和XRD考察了在还原气氛下,LaNiO_3的还原机理,这对研究其电、磁特性具有一定的指导意义.     

低压离子分离-化学发光在线检测过渡金属离子

 研究了低压离子 (LPIC)分离 柱后鲁米诺化学发光 (CL)检测方法 ,并分离测定了Cu2 + ,Co2 + ,Cr3 + ,Fe2 + ,Mn2 + 等 5种过渡金属离子。以草酸 柠檬酸混合溶液作为洗脱液 ,Luminol H2 O2 Mn + 作为化学发光检测体系 ,对过渡金属离子进行在线检测。测定的线性范围分别为 (mg·L-1) :Co2 + ,0 0 0 1～ 0 .1;Cu2 + ,0 1～ 6 ;Mn2 + ,0 0 6～ 4 ;Fe2 + ,0 0 3～ 5 ;Cr3 + ,0 0 2 5～ 1。检测限分别为 (μg·L-1) :Co2 + ,0 85 ;Cu2 + ,85 ;Mn2 + ,4 2 ;Fe2 + ,2 1;Cr3 + ,2 0。     

锰锆复合氧化物CO催化还原NO性能研究

采用柠檬酸络合法制备了锰锆复合氧化物催化剂,用XRD、H_2-TPR、XPS和SEM等技术进行了表征,研究了其CO催化还原NO性能。结果表明,MnO_x主要以Mn_3O_4物相存在,Zr占比的增加会促进Mn_3O_4物相的分散,引起Mn_3O_4平均晶粒粒径减小;Mn主要有Mn~(2+)、Mn~(3+)、Mn~(4+)离子价态形式,添加Cu和Ce后,(Mn~(3+)+Mn~(4+))含量和表面吸附氧(OA)含量增加,H_2-TPR还原峰温度向低温区偏移,有利于催化活性的提升。Mn-Zr-O复合氧化物的CO催化还原NO活性较低,加入Cu后的Mn-Cu-Zr-O复合氧化物其CO催化还原NO的活性得到改善,而添加Ce后所制备的Mn-Cu-Ce-Zr-O复合氧化物的催化活性进一步提高;在350℃下、反应空速为18000 h~(-1)时,Mn-Cu-Ce-Zr-O复合氧化物表现出较好的CO催化还原NO活性,CO转化率达到了89.17%,NO转化率达到了91.70%。     

添加元素对AB2型Laves相合金电化学性能的影响

比较系统地研究了AB2型Laves相合金Zr0.9Ti0.1Ni0.1Mn0.7V0.3M0．1(M=None，Ni．Mn．V．Co．Cr．Al．Fe，Mo．Si．C．Zn，Cu和B)的相结构和电化学性能以及高温和低温放电性能等．结果表明．14种合金均具有六方C14型Laves相的主相晶体结构．同时，含有少量立方Cl5型Laves相和一些由Zr9Ni11及ZrNi组成的非Laves相；添加V和Mn可提高AB2合金的放电容量；添加B和Mn则显著提高了AB2合金的高倍率放电性能和低温放电容量；添加Al，C．Si和Co对合金电极的循环稳定性改善明显；而Mn．Ni．V．Fe．Cu．Mo和B等却不同程度地降低了循环稳定性；添加Si．Mo，V，Cr和Al可明显改善合金电极的自放电性能；添加Si．Cr．V可显著改善AB2合金电极的高温放电性能．讨论了各种添加元素影响合金性能的可能原因．     

噻吩在M(111)(M=Pd,Pt, Au)表面的吸附

采用密度泛函理论(DFT), 选取DMol³程序模块, 对噻吩在M(111) (M=Pd, Pt, Au)表面上的吸附行为进行了探讨. 通过对噻吩在不同底物金属上的吸附能、吸附构型、Mulliken 电荷布居、差分电荷密度以及态密度的分析发现, 噻吩在Pd(111)面上的吸附能最大, Pt(111)面次之, Au(111)面最小. 吸附后, 噻吩在Au(111)面上的构型几乎保持不变, 最终通过S端倾斜吸附于top 位; 噻吩在Pd(111)及Pt(111)面上发生了折叠与变形, 环中氢原子向上翘起, 最终通过环平面平行吸附于hollow 位. 此外, 噻吩环吸附后芳香性遭到了破坏, 环中碳原子发生sp³杂化, 同时电子逐渐由噻吩向M(111)面发生转移, M(111)面上的部分电子也反馈给了噻吩环中的空轨道, 这种协同作用最终导致了噻吩分子稳定吸附于M(111)面.     

噻吩在M(111)(M=Pd,Pt,Au)表面的吸附(英文)

采用密度泛函理论(DFT),选取DMol3程序模块,对噻吩在M(111)(M=Pd,Pt,Au)表面上的吸附行为进行了探讨.通过对噻吩在不同底物金属上的吸附能、吸附构型、Mulliken电荷布居、差分电荷密度以及态密度的分析发现,噻吩在Pd(111)面上的吸附能最大,Pt(111)面次之,Au(111)面最小.吸附后,噻吩在Au(111)面上的构型几乎保持不变,最终通过S端倾斜吸附于top位;噻吩在Pd(111)及Pt(111)面上发生了折叠与变形,环中氢原子向上翘起,最终通过环平面平行吸附于hollow位.此外,噻吩环吸附后芳香性遭到了破坏,环中碳原子发生sp3杂化,同时电子逐渐由噻吩向M(111)面发生转移,M(111)面上的部分电子也反馈给了噻吩环中的空轨道,这种协同作用最终导致了噻吩分子稳定吸附于M(111)面.     

Phase Transitions in Crystalline [M(H2O)6](ClO4)2 (M=Mg,Mn, Fe,Co, Ni,Cu, Zn,Cd and Hg)

The results of DSC measurements in the temperature range 140–370 K on nine crystalline compounds of the type [M(H₂O)₆](ClO₄)₂, where M=Mg, Mn, Fe, Co, Ni, Cu, Zn, Cd and Hg, are discussed. Anomalies detected in the DSC curves are related to the existence of solid-solid phase transitions and/or to the melting points of these compounds. In consequence of two different hypothetical structural modifications of [Fe(H₂O)₆](ClO₄)₂, two DSC curves are obtained. For the compounds with M=Fe, Cd and Hg, new phase transitions have been discovered. The transition temperatures of the other phase transitions are in good agreement with literature data obtained by adiabatic calorimetry. For the compounds with M=Mg, Ni and Cd, DTA measurements were also carried out and the melting points of theses compounds were established. This revised version was published online in August 2006 with corrections to the Cover Date.     

Structure and Polymorphism of M(thd)3 (M = Al,Cr, Mn,Fe, Co,Ga, and In)

Formation, crystal structure, polymorphism, and transition between polymorphs are reported for M(thd)₃, (M = Al, Cr, Mn, Fe, Co, Ga, and In) [(thd)^– = anion of H(thd) = C₁₁H₂₀O₂ = 2, 2, 6, 6‐tetramethylheptane‐3, 5‐dione]. Fresh crystal‐structure data are provided for monoclinic polymorphs of Al(thd)₃, Ga(thd)₃, and In(thd)₃. Apart from adjustment of the M–O_k bond length, the structural characteristics of M(thd)₃ complexes remain essentially unaffected by change of M. Analysis of the M–O_k, O_k–C_k, and C_k–C_k distances support the notion that the M–O_k–C_k–C_k–C_k–O_k– ring forms a heterocyclic unit with σ and π contributions to the bonds. Tentative assessments according to the bond‐valence or bond‐order scheme suggest that the strengths of the σ bonds are approximately equal for the M–O_k, O_k–C_k, and C_k–C_k bonds, whereas the π component of the M–O_k bonds is small compared with those for the O_k–C_k, and C_k–C_k bonds. The contours of a pattern for the occurrence of M(thd)₃ polymorphs suggest that polymorphs with structures of orthorhombic or higher symmetry are favored on crystallization from the vapor phase (viz. sublimation). Monoclinic polymorphs prefer crystallization from solution at temperatures closer to ambient. Each of the M(thd)₃ complexes subject to this study exhibits three or more polymorphs (further variants are likely to emerge consequent on systematic exploration of the crystallization conditions). High‐temperature powder X‐ray diffraction shows that the monoclinic polymorphs convert irreversibly to the corresponding rotational disordered orthorhombic variant above some 100–150 °C (depending on M). The orthorhombic variant is in turn transformed into polymorphs of tetragonal and cubic symmetry before entering the molten state. These findings are discussed in light of the current conceptions of rotational disorder in molecular crystals.     

钛,锆和铪羰基化合物M(CO)_n(M=Ti,Zr,Hf;n=4～7)的理论研究

利用密度泛函方法对标题化合物的平衡几何、热化学及振动频率进行了理论预测,发现这3种金属原子都有相似的M(CO)n(n=4～7)结构.全局最低构型对M(CO)7都是单态C3v戴帽八面体7S-1,对M(CO)6都是三重态D3d畸变八面体6T(而对应的单重态M(CO)5仅比它低不到21 kJ·mol-1).对M(CO)n(n=5,4)都是三重态6S-1,其构型分别为从6T中移去1个或2个CO基的衍生物5T和4T.此外,五重态的D3h的三角双锥M(CO)5和单态的Td四面体M(CO)4以及能量更高的含有C和O同时与金属成键的独特配位CO基的M(CO)6和M(CO)3也被发现.最后,给出M(CO)7→M(CO)6+CO反应的离解能.并讨论了金属18价电子的Ti(CO)7存在的可能性.     

Tetrafluoroaurate(III) der Lanthaniden M2F[AuF4]5 (M = Tb,Dy, Ho,Er)

Tetrafluoroaurates(III) of Lanthanoides M₂F[AuF₄]₅ (M = Tb, Dy, Ho, Er) Tetrafluoroaurates(III) M₂F[AuF₄]₅ with M = Tb, Dy, Ho, Er, all yellow, have been obtained. From single crystal data they crystallize triclinic, space group P1 -C¹_i (No. 2) with Tb: a = 1 194,34(7) pm, b = 798,46(6) pm, c = 902,02(7) pm, α = 89,033(7)°, β = 88,990(6)°, γ = 89,006(7)°; Dy: a = 1 191,66(9) pm, b = 796,33(8) pm, c = 899,65(9) pm, α = 88,956(8)°, β = 89,056(8)°, γ = 88,972(8)°; Ho: a = 1 189,06(10) pm, b = 795,46(6) pm, c = 896,81(7) pm, α = 88,912(8)°, β = 89,101(7)°, γ = 88,873(8)°; Er: a = 1 185,20(40), b = 793,98(14), c = 893,83(20), α = 88,751(23)°, β = 89,187(26)°, γ = 88,884(9)°     

Synthese,Struktur und Eigenschaften der Tetraarsenidometallate(V) M7[TAs4] (M = K,Rb; T = Nb,Ta)

Synthesis, Structure, and Properties of the Tetraarsenidometallates(V) M₇[TAs₄] (M = K, Rb; T = Nb, Ta) The tetraarsenidometallates(V) M₇[TAs₄] (M = K, Rb; T = Nb, Ta) have been prepared from RbAs, KAs, Rb₃As, K₃As, and Nb or Ta in sealed Nb(Ta) ampoules at T = 1100 K. They crystallize in a new structure type oP24 (Pmn2₁, no. 31); K₇[NbAs₄]: a = 1019.2(2) pm, b = 916.2(2) pm, c = 830.6(1) pm; K₇[TaAs₄]: a = 1017.3(2) pm, b = 915.5(2) pm, c = 830.5(2) pm; Rb₇[NbAs₄]: a = 1059.2(4) pm, b = 952.8(4) pm, c = 860.4(4) pm; Z = 2 formula units per unit cell). The compounds form dark red crystals and they are sensitive against air and moisture. They are semiconductors with E_g = 1.80 eV. The thermal decomposition in dynamical vacuum gives evidence for the existance of K₄TAs₃ and K₂TAs₂ (T = Nb, Ta). Main structural units are polar oriented tetrahedra [TAs₄] with d (T – As) = 252.2(1) pm; 251.3(1) pm; 253.0(4) pm, respectively. The As atoms are trigonal prismatically coordinated by M and T atoms. These trigonal prisms form anionic and cationic layers [M₄As₂]^2? and _∞²[M₃TAs₂]²⁺ alternating along the b axis. The structure is comparable with that of Co₂P and can be described as a stuffed shear variant of the Na₆□ZnO₄ type of structure.     

Synthesis,Crystal Structures and Electrochemical Properties of Complexes [M(ImH)4(tfbdc)(H2O)] (M=Co,Ni)

The title complexes [M(ImH)₄(tfbdc)(H₂O)] ( 1 : M=Co; 2 : M=Ni) (ImH=imidazole, tfbdc=2,3,5,6‐tetrafluoroterephthalate) were synthesized by the reaction of M(OAc)₂·4H₂O, H₂tfbdc and ImH in water solution. The complexes were characterized by elemental analysis, IR spectra, thermogravimetric analysis, cyclic voltammetry and X‐ray single crystal structure analysis. Structural analysis reveals that 1 and 2 possess isostructure: monoclinic, P2₁/c, Z=4. M(II) ion in complexes 1 and 2 has a distorted octahedral geometry coordinated by one oxygen atom from water, one oxygen atom from tfbdc^2? and four nitrogen atoms from ImHs. They are discrete zero‐dimensional molecular complexes. And the adjacent monomeric components are connected by hydrogen bonds to form a supramolecule. Electrochemical properties of the complexes 1 and 2 show that electron transfer of M(II) between M(III) in electrolysis is a quasi‐reversible process.     

紫外激光诱导C60与M(CO)6(M=Cr,Mo, W)的配位反应

研究了用紫外激光(355 nm)诱导C_(60)与金属羰基化合物M(CO)_6(M＝Cr；Mo，W)的配位反应，合成了具有C_(4υ)对称性的配位络合物(η~2－C_(60))M(CO)_5，并初步讨论了C_(60)与M(CO)_6反应的动力学过程．     

M(bpy)2+3(M=Fe,Ru,Os)电子结构与相关性质

报导了对配合物Ｍ（ｂｐｙ）＾２＋３（Ｍ＝Ｆｅ,Ｒｕ,Ｏｓ）的量子化学密度泛函法研究的结果。Ｂ３ＬＹＰ／ＬａｎＬ２ＤＺ方法与基组的水平上进行计算,探讨Ｍ（ｂｐｙ）＾２＋３电子结构特征及相关性质,特别是中心原子对配合物的配位键长、光谱性质,电荷布局及化学稳定性等的影响规律,为该类配合物的合成,为分析光、电、催化作用机理提供理论参考。