聚醚砜-羟基磷灰石混合溶液的流变性能

采用N,N-二甲基乙酰胺（DMAc）为溶剂配制含羟基磷灰石（HAP）的聚醚砜（PES）溶液,研究了PES-HAP-DMAc体系的流变曲线以及HAP的质量分数、混合溶液温度等对流变性能的影响。结果表明：混合溶液的非牛顿指数（n）随着温度的升高、HAP质量分数的增大而降低,表现为非牛顿流体。     

聚乙二醇对聚醚砜超滤膜微结构和性能的影响

通过改变铸膜液中添加剂PEG的含量，测试了当铸膜液中PES的质量分数为0．21，凝固浴(DM—SO／H2O体系)中DMSO的质量分数为0．10时，所成膜的水通量和尿素、肌酐去除率。研究了PES／DMSO体系中小分子添加剂PEG作用的规律。     

醇/盐双水相体系中α-环己基扁桃酸手性分子识别

以含羟丙基-β-环糊精（HP-β-CD）手性识别剂的醇/盐双水相体系作为一种新型的手性识别萃取体系,研究了α-环己基扁桃酸(CHMA)对映体在其中的手性识别行为.详细考察了HP-β-CD浓度、CHMA浓度、乙醇和硫酸铵质量分数、体系温度和pH值等因素对CHMA对映体分配比（D）和分离因子(α)的影响.结果显示,含有手性识别剂HP-β-CD的乙醇∕硫酸铵双水相体系对CHMA对映体具有很强的手性识别能力;体系中HP-β-CD浓度、乙醇质量分数、温度和pH值等因素对对映体的分离度影响较大;在体系温度为40 ℃,pH值为2,乙醇质量分数为30%,硫酸铵质量分数为15%,HP-β-CD的浓度为50 g.L-1,CHMA浓度为0.5 mmol.L-1时,手性识别分离效果最佳,分离因子（α）达到了1.86.     

富N生物质原料气化过程NOx前驱物生成特性及规律

基于水平管式反应器气化条件，结合化学吸收-分光光度法和X射线光电子能谱（XPS）分析，研究了四种富氮生物质（豆秆（SBS）、稻秆（RS）、玉米秆（CS）和中密度纤维板（MDF））气化过程NO_x前驱物生成特性及规律，对比考察了燃料特性（燃料N官能团、N含量）及气化条件（温度、气化介质）的影响。结果表明，NH₃-N为主要NO_x前驱物并伴随一定量的HCN-N，绝大部分形成于初次裂解和二次反应同时进行的挥发分析出阶段。各因素通过影响NO_x前驱物组分生成路径而改变其产率：燃料特性对产率的影响主要体现在N官能团（胺类-N（N-A）类型）稳定性方面，与N含量关系不大，因不稳定N-A在初次裂解中的关键作用，MDF总产率高达74.7%（质量分数），比秸秆类平均总产率高出15%（质量分数）；温度和气化介质会影响二次反应中与NO_x前驱物相关的反应路径（特别是加氢氢化反应），秸秆SBS气化，温度从800℃到1000℃，NH₃-N产率从38.9%（质量分数）增加至47.7%（质量分数），HCN-N产率先增加后减少，峰值为18.3%（质量分数），源于各反应路径受温度影响的平衡性；气化介质改变加氢氢化反应，CO₂主要影响HCN-N，起一定抑制作用，H₂O主要影响NH₃-N，起促进作用，因此，通过调节气化介质比例可一定程度改变NO_x前期物组分的选择性。     

聚氧乙烯山梨醇酐脂肪酸酯乳化剂对聚氧乙烯(10)油基醚胶束形成的影响

通过平衡表面张力的测定,研究了聚氧乙烯山梨醇酐脂肪酸酯（Tween）系列与聚氧乙烯(10)油基醚（Brij97）混合胶束形成的相互作用参数βm、分子交换能εm及热力学参数（ΔGom、ΔHom、ΔSom）,并探讨了Tween系列分子结构、混合体系的组成及温度对胶束形成的影响。 研究表明,随着Tween碳链的增大,混合胶束中Tween的摩尔分数Xm1增大,协同效应增强;在Tween60/Brij97混合胶束中,ΔGom随着Tween60摩尔分数（α1）的增大而增大;在混合胶束形成中,α1≤0.33时,两组分表现出协同效应;在α1＞0.33时,未表现出协同效应;温度对Tween60/Brij97混合体系的影响表明,温度升高,CMC和ΔGom减小,ΔHom和ΔSom增大,协同效应减弱。     

DMSO对鸡蛋白溶菌酶溶液变性的影响

利用差示扫描量热(DSC)和温度调制差示扫描量热(MDSC)研究了鸡蛋白溶菌酶在纯水及二甲基亚砜(DMSO)/水混合溶剂中的热变性过程, 探讨了酶的浓度、扫描速率和共溶剂的含量对热变性行为的影响规律. 在纯水溶液中, 溶菌酶的变性焓(△Hm)随酶浓度的增大而增大. 而在DMSO/水混合溶剂中, 变性温度(Tm)随DMSO体积分数的增大向低温方向移动, 变性峰变低变宽; 当DMSO体积分数达到70%后, 热变性曲线变成了一条光滑的直线. 另外, 在纯水溶液中溶菌酶的MDSC图除了出现DSC中可观察到的主吸热峰(I)外, 在峰(I)的前面还出现一个小而对称的吸热峰(II), 并且当体系中有DMSO存在时也未能观察到此峰. 当溶菌酶浓度增大时, Tm(II)移向低温, △Hm(II)减小, Tm(I)与Tm(II)之间的距离变长. 吸热峰(II)的出现被认为是由于水溶液中溶菌酶二聚体的可逆离解造成的.     

二甲基亚砜对乙酸气相色谱保留时间的影响及其机理

通过气相色谱、红外光谱分析和量子化学计算,探究溶于二甲基亚砜（DMSO）中乙酸保留时间发生波动的原因。 结果显示,乙酸保留时间变化与DMSO体积等量递增呈线性关系,R²=0.99301;根据红外光谱分析得出,DMSO和乙酸之间生成了氢键,以DMSO-乙酸分子的形式通过色谱柱;根据Gaussian09程序计算结果,DMSO电子密度大的部分给予电子,与乙酸之间形成了氢键,而DMSO电子密度小的部分容易获得电子与具有强偶极矩的色谱柱固定液聚乙二醇产生作用力,吸附在固定液上。因此,在上述一系列复杂的分子间作用力的共同影响下,乙酸保留时间发生了波动,且随着溶剂DMSO体积比增加,乙酸保留时间不断延长。     

PANI—PBOPy复合材料的制备及介电性能

采用甲基磺酸（MSA）掺杂聚苯胺（PANI）,并以MSA为溶剂,将其与聚（2,6-亚吡啶基）苯并二嗯唑（PBOPy）采用溶液共混法制备了不同PANI质量分数的PANIPBOPy复合材料。采用红外光谱、wXRD、Uv—Vis、TGA以及SEM对复合材料的结构和性能进行了表征。研究了PANI的质量分数、温度、频率等因素对PANIPBOPy复合材料导电性能和介电性能的影响。研究表明：当PANI的质量分数达到20％时,复合材料的电导率增大了10个数量级;复合材料的介电常数和介电损耗则随着PANI质量分数的增加呈现先增大后减小的趋势,随着频率的升高先迅速降低而后趋于稳定,并且随温度升高而增大,40℃时PANI质量分数为15％的复合材料的介电常数约为230。     

激光法测定硝唑尼特结晶介稳区间

用激光法测定了不同温度下硝唑尼特在N,N-二甲基甲酰胺（DMF）、二甲基亚砜（DMSO）、甲醇和丙酮4种溶剂体系中的溶解度与超溶解度,得到硝唑尼特在不同溶剂和不同温度下的介稳区宽度。 结果表明,硝唑尼特在4种溶剂体系中的溶解度、超溶解度和介稳区宽度随温度升高逐渐增大。 在相同温度下,硝唑尼特在DMF、DMSO、甲醇和丙酮中介稳区宽度关系为：丙酮＜DMSO＜甲醇＜DMF。     

聚砜/聚醚砜相容性对合金膜结构和性能的影响

通过混合焓法预测并用相差显微镜表征了PSF/PES合金体系的相容性,表明二者为相容性比较差的部分相容体系.合金膜中聚合物的组成影响PSF/PES间的相容性,进而影响合金膜的结构和性能.随合金体系相容性下降,膜的平均孔径显著增加,水通量增大而相应的截留率下降;研究表明,改变PSF/PES间的相容性是调节膜结构、提高膜性能的有效方法.     

聚乙二醇对聚醚砜微孔膜致孔作用的研究

以聚醚砜聚乙二醇溶剂为铸膜液体系、采用干湿相转化法制备微孔滤膜,研究了各种制膜条件对膜孔径结构的影响.实验发现聚乙二醇在体系中起到分散稳定的作用,只有到浓度大于70%时,才会对铸膜液的粘度产生明显影响,聚合物在铸膜液中的溶解状态也随之改变,进而影响膜的结构.不同溶剂NMP、DMF、DMAc、DMSO等极性溶剂或固体溶剂己内酰胺均可制得开孔率较高的微孔膜,但对膜的结构和性能影响差别不大.在本研究体系中,膜的结构取决于聚乙二醇、溶剂的浓度比例关系.     

Water effect on the gelation behavior of polyacrylonitrile/dimethyl sulfoxide solution

The gelation behavior of polyacrylonitrile (PAN)/dimethyl sulfoxide (DMSO) solution containing different amounts of water has been investigated using various methods. The ternary phase diagram of PAN/DMSO/water system indicated that water enhanced the temperature at which phase separation of PAN/DMSO solution occurred. Intrinsic viscosities [η] of dilute PAN/DMSO solution and PAN/DMSO/water solution at varied temperatures were measured to examine the influence of water on the phase behavior of PAN/DMSO solution. The presence of water in the solution gave rise to elevated critical temperature T_c. The gelation temperature T_g obtained by measuring the loss tangent tan δ at different oscillation frequencies in a cooling process was found to increase with increased water content in the solution. The critical relaxation exponent n value, however, changed little with varied concentration. During the aging process, the gelation rate of PAN/DMSO solution increases with the water level. The n values of the PAN/DMSO solutions with 2 wt% and 4 wt% water were a little larger than that of the solution without water, which may be explained by the turbid gel resulted from phase separation. The n values obtained in the aging process were larger than those obtained in the cooling process for the same three solutions, ascribed to the weaker gel with less cross-linking points formed in long time. Water led to the formation of denser gel structure. The coarser gel surface can also be attributed to the phase separation promoted by water.     

丙烯腈与衣康酸在DMSO/H_2O中的聚合及聚合物性能表征

采用丙烯腈 (AN)与衣康酸 (IA)为共聚单体 ,以偶氮二异丁腈为引发剂在混合介质二甲基亚砜 水(DMSO H2 O)中自由基沉淀共聚合 ,合成了高分子量的聚丙烯腈 .通过正交设计方法研究了聚合反应条件 ,如反应温度、单体浓度、混合介质DMSO H2 O配比等对聚合反应的转化率的影响 ,还重点探讨了混合介质DMSO H2 O配比对转化率和粘均分子量的影响 .采用DSC ,TG ,IR等手段研究了PAN均聚物及 (PAN co IA)的结构与性能 .研究结果表明 ,增加反应温度 ,降低单体浓度 ,降低喂料AN IA配比中IA的含量 ,均有利于提高聚合反应的转化率 .AN与IA共聚反应的转化率随着反应介质中DMSO含量的增加而降低 ,同时聚合物的粘均分子量也降低 .对于喂料AN IA配比中IA含量相同的P(AN co IA)共聚物 ,高分子量P(AN co IA)共聚物比常规低分子量的放热峰起始温度低 ,放热峰宽     

Preparation and drug delivery study of electrospun hollow PES ultrafine fibers with a multilayer wall

The focus of this work was the preparation of hollow ultrafine fibers with a multilayer wall via coaxial electrospinning technology in one step and then studied their drug delivery properties. In this paper, by choosing a suitable dilute hydrophilic polymer solution as the core solution, polyethersulfone (PES) hollow ultrafine fibers with two different layers wall (porous structure layer and dense smooth layer) were formed during coaxial electrospinning process in one step. They showed good drug delivery capacity when curcumin was used as the model drug. There were much larger delivery amounts, more stable release rate, and higher utilization rate of PES hollow ultrafine fibers with a multilayer wall to curcumin than that of PES porous ultrafine fibers. Compared with porous ultrafine fibers, hollow ultrafine fibers with two different layers wall were more suitable to be used as drug delivery materials. Besides, between the two hollow ultrafine fibers with two different layers wall mentioned in this paper, there was much better drug delivery capacity for the hollow fibers produced with the core solution of PVA/DMSO. These results showed that PES hollow ultrafine fibers with two different layers wall have the potential to be used as the drug delivery materials.     

Polyethersulfone/polyacrylonitrile blend ultrafiltration membranes with different molecular weight of polyethylene glycol: preparation,morphology and antifouling properties

Asymmetric ultrafiltration (UF) membranes were prepared from blends of polyethersulfone (PES)/polyacrylonitrile (PAN) via phase inversion method induced by immersion precipitation. Polyethylene glycol (PEG) with four different molecular weights was used as pore former and hydrophilic polymeric additive. N,N‐dimethylformamide (DMF) and water were used as solvent and coagulant (nonsolvent), respectively. The effects of different proportion of PES/PAN and molecular weight of PEG on morphology and performance of the prepared membranes were investigated. Performance of the membranes was evaluated using UF experiments of pure water and buffered bovine serum albumin (BSA) solution as feed. The contact angle measurements indicated that the hydrophilicities of PES/PAN membrane increase by increasing the PAN concentration in the casting solution. However, performance of the membranes improves by increasing the PAN concentration in the casting solution up to 20% and then decreases with further addition of PAN. It was found out that the rejection of BSA decreases with increasing the PAN concentration in the casting solution. Furthermore, it was found that the performance of the membranes increases by increasing the molecular weight of PEG up to 1500 Da and then decreases with the higher molecular weights. The morphology of the prepared membranes was studied by scanning electron microscopy. Copyright © 2011 John Wiley & Sons, Ltd.     

DNA sequencing of close to 1000 bases in 40 minutes by capillary electrophoresis using dimethyl sulfoxide and urea as denaturants in replaceable linear polyacrylamide solutions

The goal of this work was to reduce the capillary electrophoresis (CE) separation time of DNA sequencing fragments with linear polyacrylamide solutions while maintaining the previously achieved long read lengths of 1000 bases. Separation speed can be increased while maintaining long read lengths by reducing the separation matrix viscosity and/or raising the column temperature. As urea is a major contributor to the separation buffer viscosity, reducing its concentration is desirable both for increase in the separation speed and easier solution replacement from the capillary. However, at urea concentrations below 6 M, the denaturing capacity of the separation buffer is not sufficient for accurate base-calling. To restore the denaturing properties of the buffer, a small amount of an organic solvent was added to the formulation. We found that a mixture of 2 M urea with 5% v/w of dimethyl sulfoxide (DMSO) resulted in 975 bases being sequenced at 70 degrees C in 40 min with 98.5% accuracy. To achieve this result, the software was modified to perform base-calling at a peak resolution as low as 0.24. It is also demonstrated that the products of thermal decomposition of urea had a deleterious effect on the separation performance at temperatures above 70 degrees C. With total replacement of urea with DMSO, at a concentration of 5% v/w in the same linear polyacrylamide (LPA)-containing buffer, it was possible to increase the column temperature up to 90 degrees C. At this temperature, up to 951 bases with 98.5% accuracy could be read in only 32 min of separation. However, with DMSO alone, some groups of C-terminated peaks remained compressed, and column temperature at this level cannot at present be utilized with existing commercial instrumentation.     

Synthesis and characterization of asymmetric polyethersulfone membranes: effects of concentration and polarity of nonsolvent additives on morphology and performance of the membranes

In this study, effects of methanol, ethanol and 1‐propanol as variable nonsolvent additives (NSAs) on the morphology and performance of flat sheet asymmetric polyethersulfone (PES) membranes were investigated. The membranes were prepared from PES/Polyvinylpyrrolidone (PVP)/N‐methyl‐2‐pyrrolidone (NMP) system via phase inversion. The obtained results indicate that with the addition of NSAs to the casting solution, the membrane morphology changes slowly from macrovoids to an asymmetric structure with finger‐like pores. By increasing the NSAs concentrations in the casting solution and decreasing their polarities, the membrane structure changes from finger‐like pores to sponge. The AFM and SEM images reveal that addition of NSA to the casting solution decreases the pore size of the prepared membranes and reduces the pure water flux and BSA solution flux, while increasing the protein rejection. Surface analysis of the membranes showed that mean pore size and surface porosity of the prepared membranes with NSAs in the casting solution are smaller compared with those of the membrane prepared with no NSA. Pure water flux and BSA solution flux through the membranes decrease and BSA rejection increases with increase in the concentration of NSAs and decrease in their polarity. Finally, it can be concluded that the T_g values of the PES membranes increase by addition of NSAs to the casting solution. Copyright © 2009 John Wiley & Sons, Ltd.     

Molecularly imprinted polyethersulfone microspheres for the binding and recognition of bisphenol A

BPA-imprinted polyethersulfone (PES) microspheres for the binding and recognition of bisphenol A (BPA) were fabricated by means of a liquid-liquid phase separation technique. The imprinted novel PES microspheres had a porous structure with a skin layer, under which was followed by a finger-like structure. The recognition experiments with the BPA-imprinted microspheres were carried out by applying the microspheres to various BPA solutions. In water, high binding amounts of BPA were observed in the range of 19-42 μmol/g capacity, but the recognition was low in the BPA water solution. With the increase of the concentration in BPA solution, the binding amounts and the recognition coefficient increased. However, 1,4-butylene glycol/water media showed high recognition of the imprinted microspheres with a low binding capacity of BPA. In addtion, with the increase of the BPA amounts in the PES solution used to prepare the imprinted microspheres, the specific recognition sites increased, and the recognition ability increased. Evidence revealed that microsphere recognition was effective for BPA due to the binding to specific recognition sites [S]_(sites). The imprinted microspheres showed the selectivity for BPA in the wine including BPA and other organic compounds. Charge transfer and special cavities could be employed to explain the mechanism.     

LCST and UCST behavior of poly(N-isopropylacrylamide) in DMSO/water mixed solvents studied by IR and micro-Raman spectroscopy

Temperature-responsive phase separations of poly(N-isopropylacrylamide) (PNiPAm)/dimethylsulfoxide (DMSO)/water mixtures have been investigated by infrared and confocal micro-Raman spectroscopy. The ternary mixtures exhibited lower critical solution temperature (LCST) and upper critical solution temperature (UCST) phenomena at low and high DMSO concentrations, respectively. The amide I band of PNiPAm consists of two components; the intensity of the 1650 cm-1 component increased, and that of the 1625 cm-1 component decreased with increasing temperature during both LCST and UCST phase transitions. Gradual red shifts of the C-H stretching and the amide II bands with increasing temperature or increasing DMSO concentration indicate a removal of water molecules from the alkyl and N-H groups. Raman microscopic measurements showed that DMSO is excluded from the polymer-rich phases upon both LCST and UCST phase separation. On the basis of the experimental results and the quantum chemical calculations, a model that explains the solvation change of the polymer during phase transitions was proposed.