锰助剂对Fe／ZrO2催化剂F—T反应催化性能的影响

应用ＸＲＤ，ＸＰＳ，Ｍｏｓｓｂａｕｅｒ谱，ＴＰＲ，ＣＯ化学吸附ＣＯ－ＴＰＤ，ＣＯ＋Ｈ２反应性能测试等手段研究了锰助剂对Ｆ－Ｔ合成制低碳烯烃Ｍｎ－Ｆｅ／ＺｒＯ２催化剂结构及催化性能的影响。结果表明，与Ｆｅ／Ｚｒ催化相比，加锰助剂后的催化剂Ｆ－Ｔ反应催化活性上升，甲烷选择性降低，低碳烯烃选择性增加。     

Fe_2O_3／ZrO_2催化剂上一氧化碳加氢反应制低碳烯烃 Ⅱ．预处理条件对催化剂结构及性能的影响

用ＴＰＲ，Ｍｏｓｓｂａｕｅｒ谱法，ＸＰＳ，ＸＲＤ及反应评价等手段研究了Ｆｅ２Ｏ３／ＺｒＯ２催化剂的还原行为、铁物种状态和ＣＯ加氢反应性能．结果表明，预处理条件明显影响Ｆｅ２Ｏ３／ＺｒＯ２催化剂表面铁原子的数量、铁锆间的相互作用、催化剂的物相变化以及ＣＯ加氢反应的催化性能．以Ｆｅ２Ｏ３／ＺｒＯ２经氢氟混合气程序升温至７５３Ｋ还原生成的Ｆｅ－Ｚｒ－Ｏ物种为前身，在合成气中进一步还原得到的铁锆催化剂，具有较好的Ｆ－Ｔ反应合成低碳烯烃的选择性．     

碱改性γ－Al_2O_3催化剂表面碱强度分布与COS水解活性的研究

用非水滴定法和Ｈａｍｍｅｔｔ系列指示剂测定了ＣＯＳ水解碱改性γ－Ａｌ_２Ｏ_３催化剂的表面碱强度分布．发现表面碱强度分布不均匀与表面能量分布不均匀相呼应．采用零点酸碱强度（Ｈ_（０，ｍａｘ））及碱中心区域分析法，Ｂｒｏｎｓｔｅｄ催化定律，进一步证实ＣＯＳ水解反应具有明显碱催化特征，较高活性催化剂的Ｈ_（０，ｍａｘ）一般为１０左右，对ＣＯＳ水解反应起主要作用的碱性中心的碱强度（Ｈ_０）为４．８≤Ｈ_０≤９．８．对碱金属氧化物改性后的γ－Ａｌ_２Ｏ_３催化剂，Ｂｒｏｎｓｔｅｄ规律在每个碱强度分区域内是适用的．     

Fe_2O_3／ZrO_2催化剂上一氧化碳加氢反应制低碳烯烃──I．催化剂反应性能及反应过程中铁物相的变化

用浸渍法制得一系列不同铁负载量的Ｆｅ２Ｏ３／ＺｒＯ２催化剂，应用催化反应评价结合穆斯堡尔谱对催化剂的ＣＯ加氢反应性能、催化剂活性相结构及催化剂铁物种在合成气反应过程中的物相变化进行了研究．结果表明，铁负载量的大小对于Ｆｅ２Ｏ３／ＺｒＯ２催化剂的Ｆ－Ｔ反应催化性能有很大影响，铁负载量适当时，Ｆｅ２Ｏ３／ＺｒＯ２催化剂铁锆间适当的强相互作用使得催化剂在保持较高催化活性的同时高选择性地生成低碳烯烃，产物分布偏离Ｓｃｈｕｌｚ－Ｆｌｏｒｙ分布规律．     

担体对Fe-MnO催化剂CO加氢合成烯烃性能影响的TPSR表征

考察了不同担体担载的Ｆｅ－ＭｎＯ催化剂上ＣＯ加氢合成烯烃的反应。结果表明担体直接影响低碳烯烃选择性。通过对催化剂的ＣＯ，ＣＯ／Ｈ２，Ｃ２Ｈ４等吸附的ＴＰＳＲ表征及催化剂表面ＣＯ加氢微观反应的研究，证明以碱性担体为基质的ＰＢＣ催化剂具有强吸附ＣＯ能力，且生成的烯烃不易发生二次反应，因而ＰＢＣ催化剂具有较高的烯烃选择性；以酸性担体为基质的ＰＡＣ催化剂对ＣＯ为弱吸附，对Ｈ２为较强吸附，且烯烃会发生强烈的     

氧化铈对F-T反应铁锆催化剂的助催化作用

应用ＸＲＤ、ＸＰＳ、Ｍｏｓｓｂａｕｅｒ谱、ＴＰＲ、ＣＯ－ＴＰＤ、ＣＯ＋Ｈ２反应性能测量试等手段研究了ＣｅＯ２对Ｆ－Ｔ合成制低碳烯烃Ｃｅ－Ｆｅ／ＺｒＯ２催化剂催化性能的影响。结果表明，与Ｆｅ／Ｚｒ催化剂相比，加铈助剂后的催化剂Ｆ－Ｔ反应催化活性明显上升。     

Kam insky型催化剂催化乙烯齐聚──二酚基二茂锆的催化作用

通过改变 Ａｌ／ Ｚｒ 比、反应温度及反应时间, 分别考察了 Ｃｐ２ Ｚｒ（ Ｏ Ａｒ）２／ Ｅ Ａ Ｏ （ Ａｒ＝ Ｃ６ Ｈ５、ｐ  Ｃ６ Ｈ４ Ｍ ｅ、ｍ  Ｃ６ Ｈ４ Ｎ Ｏ２、ｐ  Ｃ６ Ｈ４ Ｎ Ｏ２） ４ 种体系对乙烯齐聚的催化作用． 发现用 Ｃｐ２ Ｚｒ（ Ｏ Ａｒ）２ 代替 Ｃｐ２ Ｚｒ Ｃｌ２ 作为主催化剂, 对于 Ｋａｍ ｉｎｓｋｙ 型体系 Ｃｐ２ Ｚｒ Ｌ２／ Ｅ Ａ Ｏ 催化乙烯齐聚, 具有调变作用,在提高催化活性的同时, 可使低碳烯烃的选择性明显改善． 在 Ｃｐ２ Ｚｒ（ Ｏ Ａｒ）２／ Ｅ Ａ Ｏ 的４ 种催化体系中, 当酚基对位带有强吸电子基团时（ Ａｒ＝ ｐ  Ｃ６ Ｈ４ Ｎ Ｏ２）, 对乙烯齐聚的催化性能最佳．     

天然气和氧偶联制环氧乙烷催化剂的反应性能

研制了天然气和氧经偶联反应制环氧乙烷的Ａｇ－Ｂａ－Ｃｓ／Ａｌ２Ｏ３催化剂（ＮＥＯ－１）。用Ｎ２＋Ｏ２＋Ｃ２Ｈ４和偶联产物气加氧作原料气，在２５０℃，空速２５００ｈ＾－１时，乙烯转化率和ＥＯ选择性分别达到了３０％和８０％，ＮＥＯ－１催化具有适宜的比表面和孔结构，用ＸＰＳ分析发现，与新鲜的催化相比，经活化和反应后的催化剂表面的Ｂａ，Ｃｓ原子浓度增高，并具有较多的吸附氧物种。     

K_2O和MnO助剂对Fe／Silicalite－2催化剂CO加氢制低碳烯烃性能的影响

在Ｓｉｌｉｃａｌｉｔｅ－２分子筛担载的铁催化剂中添加ＭｎＯ和Ｋ２Ｏ助剂，可显著提高其ＣＯ加氢制低碳烯烃的选择性及催化活性．ＭｎＯ助剂主要抑制乙烯和丙烯的加氢反应而提高烯／烷比值；Ｋ２Ｏ助剂则增加催化剂对ＣＯ的吸附能力，同时抑制乙烯在催化剂表面的二次反应（主要是乙烯的歧化反应），从而有利于提高低碳烯烃的选择性及催化剂活性．     

Fe/ZrO2催化剂的Mossbauer谱及XAFS表征

考察了经不同温度还原的Ｆｅ／ＺｒＯ２催化剂在ＣＯ２加氢制低碳烃反应中的催化活性,最佳结果为ＣＯ２转化率２７．０％,对Ｃ２＋烃的选择性５６．７％,采用ＸＲＤ,＾５７ＦｅＭｏｓｓｂａｕｅｒ谱,Ｆｅ－Ｋ－吸收边的Ｘ射线吸收近边结构（ＸＡＮＥＳ）及扩展Ｘ射线吸收精细结构（ＥＸＡＦＳ）等表征方法研究了催化剂的表面结构。结果表明,在ＺｒＯ２表面上主要存在α－Ｆｅ及配位不饱和的Ｆｅ＾３＋两种物种。催化剂表面明显呈氧缺位,零价铁相对富集的状态,还原温度对表面结构有显著的影响,最佳还原温度与表面Ｆｅ－Ｏ键的键长有关,结合这种催化剂在ＣＯ２加氢制低碳烃反应中的催化活性,认为α－Ｆｅ与配位不饱和的Ｆｅ＾３＋物种的协同作用是其具有较高催化活性的重要原因。     

A comparative study of the surface structure, acidity, and catalytic performance of tungstated zirconia prepared from crystalline zirconia or amorphous zirconium oxyhydroxide

Tungstated zirconias prepared from W deposition on zirconium oxyhydroxide are reportedly active for alkane isomerization, whereas solids synthesized by impregnation of zirconia are inactive. The origin of the differences between the two preparations is not fully understood. The present paper examines the influence of W surface density and the nature of the support on the surface structure, development of the acidity, and catalytic performance of WO(x)()/ ZrO(2) catalysts. Two series of catalysts containing W surface densities up to 5.2 at. W/nm(2) were prepared by pore volume impregnation of two different supports: zirconium oxyhydroxide and predominantly tetragonal zirconia (65% tetragonal, 35% monoclinic). The texture and structure of the catalysts were investigated by BET measurements, X-ray diffraction, Raman and infrared spectroscopy. The catalytic activity was tested for 2-propanol dehydration and n-hexane isomerization. For catalysts obtained by impregnation of Zr oxyhydroxide, Raman results showed that W was present as a surface phase. Infrared spectra indicated an increase in the degree of polymerization of W species with increasing W surface density. The development of the acidity was monitored by lutidine adsorption and desorption at 523 K, followed by infrared spectroscopy. The results indicated the presence of a threshold of W surface density at 1.3 at. W/ nm(2) for the detection of these acid sites, followed by a progressive increase in their abundance with increasing W surface density. The development of Br?nsted acidity correlated with the evolution of the infrared bands attributed to "extensively" polymerized W species. A direct relationship was observed between the abundance of Br?nsted acid sites and the catalytic activity for 2-propanol dehydration. For n-hexane isomerization, compared to 2-propanol dehydration, a higher threshold of W surface densities (3.4 at. W/ nm(2)) for the development of activity was observed. The difference was attributed to stronger Br?nsted acid sites required for n-hexane isomerization. The catalysts prepared by impregnation of zirconia exhibited comparable behavior. For a given W surface density, the crystalline composition of the support (tetragonal/monoclinic zirconia), the W surface structure, abundance of Br?nsted acid sites, and catalytic performance were similar. Thus, in an apparent variance with some of the results reported in the literature with respect to the influence of preparation methods, no significant effect of the initial form of the support (Zr oxyhydroxide versus predominantly tetragonal zirconia) was evidenced.     

Fourier transform infrared spectroscopic study of surface acidity by pyridine adsorption on Mo/ZrO2-SiO2(Al2O3) catalysts

Acidity of the oxidic molybdenum catalysts supported on mixed ZrO2-SiO2 and ZrO2-Al2O3 carriers was investigated by Fourier transform infrared spectroscopy of pyridine adsorption. Deposition of molybdenum on ZrO2-SiO2 and ZrO2-Al2O3 supports leads to formation of surface Br?nsted acid sites. The number of the Br?nsted and Lewis acid sites in supported-molybdenum catalysts depends on both the ZrO2 content and the type of the support. With increasing ZrO2 content, the Lewis acid sites increase for both series of catalysts. The Br?nsted acid sites are higher for Mo/ZrO2-SiO2 samples compared to those for Mo/ZrO2-Al2O3 and also increase with zirconia.     

CO2/H2在不同形态ZrO2上的吸附行为

利用傅立叶变换红外光谱技术(FT-IR)考察了CO2和CO2＋H2在不同形态氧化锆上的吸附和转化行为，结果表明,氧化锆的形态影响CO2的吸附形式和表面物种的生成.无定型氧化锆上主要生成碳酸氢盐和离子碳酸盐，单斜氧化锆上还出现了双齿碳酸盐，而在四方氧化锆上出现最强的线式吸附CO2，并生成聚碳酸盐.在氢气存在的条件下，单斜氧化锆上生成甲烷而在四方氧化锆上则生成甲酸盐.     

Solvent-free preparation of nanosized sulfated zirconia with Brønsted acidic sites from a simple calcination

Nanosized sulfated zirconia with Br?nsted acidic sites has been prepared by a simple calcination in the absence of any solvent. XRD patterns reveal that the sulfated zirconia mainly consists of tetragonal crystalline zirconia with average size of about 7 nm, which is further confirmed by TEM images. N2 adsorption data show that the nanosized sulfated zirconia has high surface area (165-193 m2/g) and exhibits uniform pore distribution aggregated by zirconia nanoparticles. IR spectra of samples show that the sulfur species in the nanosized sulfated zirconia is a little different from that in conventional sulfated zirconia. Furthermore, IR spectra of adsorbed pyridine indicate that the nanosized sulfated zirconia contains relatively more Br?nsted acidic sites than conventional sulfated zirconia. Catalytic tests show that the nanosized sulfated zirconia exhibits much higher activity than conventional sulfated zirconia in catalytic esterification of cyclohexanol with acetic acid.     

Adsorption of 2-chloropyridine on oxides--an infrared spectroscopic study

The adsorption of 2-chloropyridine on SiO(2), TiO(2), ZrO(2), SiO(2)-Al(2)O(3) and H-mordenite has been studied by IR spectroscopy. The different modes of interaction with oxide surfaces, i.e. hydrogen-bonding and adsorption at Br?nsted or Lewis acid sites, was modelled by ab initio calculations at the B3LYP/DZ+(d) level. Adsorption on SiO(2) results in hydrogen bonding to surface hydroxyl groups, whereas the spectra obtained following adsorption on TiO(2) and ZrO(2) display evidence for electron transfer at Lewis acidic surface sites. Protonation of 2-chloropyridine at Br?nsted acidic sites was detected only for adsorption on SiO(2)-Al(2)O(3) and H-mordenite, indicating the presence of Br?nsted acidic sites on these oxide surfaces with pK(a) values 相似文献   

不同形态ZrO2负载Co催化剂上CO+H2吸附与反应行为研究

利用FTIR,TPSR和微量反应技术考察了CO和CO/H2在无定形、四方相和单斜相3种形态氧化锆为载体的钴基催化剂上的吸附和反应行为.结果表明,CO在以不同形态氧化锆为载体的催化剂上的吸附形式和转化行为具有较大差异.在单斜氧化锆为载体的催化剂上生成桥式和多桥式吸附的CO,并容易进一步加氢生成烃类物种,具有较高的反应活性和C5+烃的选择性.而以四方氧化锆为载体的催化剂上桥式吸附的CO较稳定,加氢反应活性较低.     

Correlations between acidity, surface structure, and catalytic activity of niobium oxide supported on zirconia

The development of the acidity and the relationship between acidity, catalytic activity, and the surface structure for niobium oxide supported on zirconia were investigated for a series of solids. The catalysts were active for 2-propanol dehydration only above a threshold in Nb loading. The acidity was studied by infrared spectroscopy of adsorbed 2,6-dimethylpyridine as a probe molecule, and the onset of activity was correlated with that of the formation of relatively strong Br?nsted acid sites. The variation in the abundance of these sites also correlated with the catalytic activity. Raman, IR, and UV spectroscopy results indicated that the active sites were related to polymeric Nb surface species. These results were compared to those previously reported for the WO(x)/ZrO(2) catalysts.     

FeOx／ZrO2催化剂结构及CO氧化性能的研究

利用XRD、TPR及固定床微反技术,研究了添加FeOx对ZrO2载体结构稳定性和催化性能的影响。结果表明,FeOx对载体ZrO2具有良好的热稳定性,能阻止ZrO2从四方晶型向单斜晶型的转变;FeOx与载体ZrO2之间的相互作用,能促进FeOx在载体表面的分散,并提提高FeOx/ZrO2催化剂的氧化和还原性能。     

Relations between structure, acidity, and activity of WOx/TiO2: influence of the initial state of the support, titanium oxyhydroxide, or titanium oxide

Two series of WO(x)/TiO(2) catalysts, containing W surface densities up to 4.4 W atoms/nm(2), were prepared by pore volume impregnation of two different supports, titanium oxyhydroxide (amorphous) or titanium oxide (crystallized, 100% anatase). The influence of W surface density and the nature of the support on the surface structure, development of the acidity, and catalytic performances were examined. The texture and structure of the catalysts were investigated by Brunauer-Emmett-Teller measurements, X-ray diffraction (XRD), and Raman and infrared spectroscopy. The catalytic activity was tested for 2-propanol dehydration and n-hexane isomerization. For catalysts obtained by impregnation of titanium oxide, XRD and Raman results showed that W was present as a surface phase. Infrared spectra indicated an increase in the degree of polymerization of W species with increasing W surface density. CO and lutidine adsorption, followed by infrared spectroscopy, showed an increase in the strength and abundance of Br?nsted acid sites (measured after lutidine desorption at 573 K) with the W surface density above a threshold of 1.3 W atoms/nm(2). The development of Br?nsted acidity correlated with the evolution of the infrared bands attributed to polymerized W species. A direct relationship was observed between the concentration of Br?nsted acid sites and the catalytic activity for 2-propanol dehydration. Catalytic activity, for n-hexane isomerization, appears to be associated with the presence of highly condensed W species. The catalysts synthesized by impregnation of titanium oxyhydroxide exhibited a comparable behavior. Hence, for a given W surface density, the W surface structure, concentration of Br?nsted acid sites, and catalytic performances were similar. Thus, no significant effect of the initial form of the support (titanium oxyhydroxide versus titanium oxide; 100% anatase) was evidenced.     

Acidity, surface structure, and catalytic performance of WO(x) supported on monoclinic zirconia

The relationship between the acidity, catalytic activity, and surface structure for tungsten oxide supported on zirconia was investigated for a series of solids prepared by equilibrium adsorption on monoclinic zirconia. The catalysts were active for propanol dehydration only above a threshold in W loading. The acidity was studied by infrared spectroscopy of adsorbed probe molecules (2,6-dimethylpyridine and CO), and the onset of activity was correlated with that of the formation of relatively strong Br?nsted acid sites. The variation in the abundance of these sites correlated with the catalytic activity. Lewis sites were present but could not be directly associated with the activity. Raman, IR, and UV spectroscopy results indicated that the active sites were related to polymeric W surface species.