新型球形纳米空心SiO2的模板合成方法研究

以纳米碳酸钙颗粒为新颖的无机模板剂,硅酸钠为无机硅源,通过溶胶-凝胶法形成CaCO3／SiO2的核壳结构;随后通过高温煅烧、酸溶和干燥处理,合成出了具有高比表面积的球形纳米空心二氧化硅粒子．然后,分别采用TEM,SEM,EDS,XRD,FTIR和TG等测试手段对样品进行了分析和表征,并考察了不同合成条件,如反应温度、反应pH值、煅烧温度和包覆反应时SiO2／CaCO3的配比对纳米空心二氧化硅粒子的比表面积变化．实验结果表明：较高的反应温度如60～80℃,pn值9左右、SiO2包覆量为碳酸钙质量的10％,以及煅烧温度为700℃,有利于形成空心形貌较好、比表面较大的球形纳米空心二氧化硅。     

SiO2/Co3O4核壳催化剂对AP热分解的催化性能研究

采用改良的Stöber法制备粒径约为200 nm的单分散球形SiO₂颗粒,以此为内核,分别通过液相沉淀法和尿素均匀沉淀法制备包覆形式不同的新型SiO₂/Co₃O₄核壳式纳米催化剂。采用X-射线衍射分析(XRD)、透射电子显微镜(TEM)、红外光谱分析(IR)、拉曼光谱分析(Raman)、BET比表面积测试等手段对产物进行表征,利用差式扫描量热仪(DSC)考察SiO₂/Co₃O₄复合物对高氯酸铵(AP)热分解反应的催化作用,探讨不同包覆形式对其催化活性的影响。结果表明,两种方法制备得到的SiO₂/Co₃O₄复合物分别为层包覆和粒子包覆,比表面积大,具有明显的核壳结构,且粒子包覆形式的SiO₂/Co₃O₄对AP热分解反应的催化效果最好,使AP的高温分解温度降低了110 ℃,放热量增加了662 J·g^-1。     

Au@ZrO2空心纳米微球的制备及其催化性质

以Stober法合成了不同粒径的SiO₂微球。以这些SiO₂微球为硬模板,通过ZrOCl₂前驱体吸附和水解制备得到了ZrO₂@SiO₂复合物,然后用HF溶解去除二氧化硅模板剂,制备得到ZrO₂空心球。以ZrO₂空心球为载体,采用沉积-沉淀法（DP）合成了Au@ZrO₂纳米空心微球。考察了Au@ZrO₂纳米空心微球在对硝基苯胺还原反应中的催化性能。研究结果表明,所合成的SiO₂微球粒径大小均一、形状规则、分散性好;ZrO₂空心微球大小及比表面积可以通过硬模板SiO₂微球粒径进行有效控制;与Au@ZrO₂实心微球相比,Au@ZrO₂空心微球在对硝基苯胺还原反应中表现出良好的催化性能,当反应温度为45℃、反应7 min时,对硝基苯胺能够完全转化为对苯二胺。     

用ATRP方法制备聚苯乙烯/纳米二氧化硅杂化粒子

采用过量的甲苯-2,4-二异氰酸酯(TDI)对SiO₂纳米粒子表面进行修饰, 将原子转移自由基聚合(ATRP)引发剂引入到SiO₂粒子表面合成大分子引发剂, 采用ATRP技术将聚苯乙烯(PS)大分子链接枝到SiO₂表面制备出以纳米二氧化硅为核, 聚苯乙烯为壳的PS/SiO₂杂化粒子. 利用红外光谱(FTIR)、核磁共振谱( NMR)、凝胶色谱(GPC)等实验手段对杂化粒子及表面接枝聚苯乙烯进行了表征分析.     

纳米TiO2-SiO2复合光催化剂的超临界流体干燥法制备及其光催化性能研究

本文以廉价无机盐Na₂SiO₃·9H₂O和TiCl₄溶液为原料,采用化学包覆结合超临界流体干燥(SCFD)法制备纳米级TiO₂-SiO₂复合光催化剂。利用XRD、TEM、NMR等手段对复合粉体进行了表征。结果表明,采用超临界流体干燥法可直接制得锐钛矿型TiO₂-SiO₂纳米复合光催化剂,其中SiO₂以单分散、无定形形式存在。以苯酚和邻苯二酚紫光催化降解为反应模型,考察了TiO₂-SiO₂复合光催化剂的催化性能。证明掺入适量SiO₂的TiO₂-SiO₂纳米复合光催化剂既减少了TiO₂的用量、降低了成本,又在某种程度上提高了TiO₂的光催化活性。SiO₂的引入可以有效抑制纳米粒子粒径的长大和晶相的转变,增强了二氧化钛纳米粒子的热稳定性。二氧化硅的最优掺杂量为15%(质量分数)。     

不同pH值制备的TiO2和TiO2/SiO2催化剂结构、表面性质及光催化活性

以TiOSO₄和SiO₂溶胶为原料, 采用沉淀法用氨水调节pH值制备TiO₂和TiO₂/SiO₂催化剂. 制备的催化剂用X射线衍射(XRD), 扫描电镜(SEM), N₂吸附(BET), 紫外-可见(UV-Vis)漫反射光谱, 程序升温脱附(NH₃-TPD), 傅里叶变换红外(FT-IR)光谱技术分析. XRD谱图显示纯TiO₂中锐钛型和金红石相共存, 且金红石相含量随pH值升高而增加. 但是, TiO₂/SiO₂催化剂只有锐钛型. 扫描电镜发现制备的催化剂呈类球形, 颗粒间相互交叠, 粒径在10-25 nm之间. TiO₂和TiO₂/SiO₂光催化剂的比表面积随pH值升高略有增大. SiO₂的添加会增大催化剂的比表面积. 程序升温脱附实验结果说明催化剂的表面酸量随pH值升高而增加. TiO₂/SiO₂的表面酸量比相同pH值制备的TiO₂大. 红外光谱分析说明Si掺杂和高pH值有利于催化剂表面生成更多的羟基. TiO₂和TiO₂/SiO₂光催化剂的催化活性随pH值升高而明显增强. TiO₂/SiO₂的光催化活性优于TiO₂. TiO₂/SiO₂催化剂具有较好的耐久性.     

反相微乳液法制备纳米Al2O3颗粒及其形成反应机理的研究

通过聚乙二醇辛基苯基醚(曲拉通X-100)/正丁醇/环己烷/水溶液形成的体系, 采用反相微乳液法合成了Al₂O₃纳米粒子. 对前驱体进行热分析(TG-DTG-DTA), 确定了合适的煅烧温度为1150 ℃. 采用X射线衍射(XRD)、透射电镜(TEM)、紫外可见分光光度法(UV-vis)分别对产物的结构、粒度和形貌进行了表征, 考察了微乳液中水与表面活性剂的物质的量之比(ω_o)、煅烧温度和煅烧时升温速率等关键因素对产物形貌和晶相的影响, 并通过分析进一步揭示了Al₂O₃纳米粒子的形成机理. 结果表明, 控制ω_o为10、煅烧温度为1150 ℃可得到分散性好、粒径分布均匀的Al₂O₃纳米粒子, 且2 ℃/min的升温速率更有利于产物向稳定的α晶相转变.     

SiO2-CeO2复合氧化物的制备及抛光性能

采用正硅酸乙酯溶胶-凝胶法制备纳米SiO₂，并与氯化铈溶液混合，用氨水沉淀法制备了SiO₂-CeO₂复合氧化物。利用XRD、SEM等手段对其物相类型、外观形貌、颗粒大小、表面电位等物理性能进行了表征，测定了它们对3种光学玻璃的抛光速率。结果表明：合成复合氧化物具有立方萤石型结构，由Sherrer方程计算的晶粒D_XRD(200)小于100 nm甚至10 nm。随着SiO₂复配量的增加和煅烧温度的降低，晶粒度减小，比表面增大；激光粒度分析仪测定的中位粒径D₅₀在2～3 μm之间，且随SiO₂复配量的增加呈增大趋势，但随煅烧温度的变化在800 ℃时出现极小值，而此时的ζ电位的负值最大，对3种玻璃的抛光速率也最大。证明抛光速率与表面电位及相应的悬浮性、颗粒大小有直接关系。随着SiO₂复配量的增加，复合氧化物的ζ电位负值及对3种玻璃的抛光速率均增大。因此，在CeO₂中复配SiO₂是提高抛光速率的有效方法，此时，最佳的煅烧温度为800 ℃。     

SiO2@CdTe@Au复合纳米粒子的制备与非线性吸收特性

应用SiO₂纳米粒子、CdTe量子点和Au纳米粒子,采用逐层吸附法制备SiO₂@CdTe@Au纳米复合材料。同时对样品进行了测试和表征,从多个方面证明纳米复合材料成功制备。利用Z扫描技术测量了SiO₂@CdTe和SiO₂@CdTe@Au纳米复合材料在纳秒激光脉冲作用下的非线性吸收光学特性。实验结果表明：SiO₂@CdTe和SiO₂@CdTe@Au纳米复合材料均表现出饱和吸收特性。SiO₂@CdTe@Au较SiO₂@CdTe纳米复合材料具有更强的非线性光学特性,并对其机理进行了分析。     

核/壳型CdTe@SiO2荧光纳米复合粒子的制备与表征

利用反相微乳法, 以巯基乙酸修饰的水溶性CdTe量子点为核, 包覆SiO₂, 制备得到核壳型CdTe@SiO₂荧光纳米复合粒子. 用紫外-可见(UV-vis)分光光度计, 荧光(PL)分光光度计, 红外(FT-IR)光谱仪, 透射电子显微镜(TEM)等分析测试手段, 对得到的荧光纳米复合粒子的性能进行表征, 结果表明: 得到的CdTe@SiO₂纳米复合粒子是核壳型结构, 由SiO₂壳层包覆多个量子点, 其大小均匀, 水溶性好, 有效地提高了量子点的稳定性, 大大增强了其抗光漂白性能, 为该材料的进一步生物应用打下了良好的基础.     

Fabrication of hollow SiO2 and Au (core)–SiO2 (shell) nanostructures of different shapes by CdS template dissolution

Core–shell silica (SiO₂) coated CdS nanorods (NR) and nanospheres (NS) were prepared (SiO₂@CdS) by deposition of a Si–O–Si amorphous layer over the CdS surface through the hydrolysis of 3-mercaptopropyltrimethoxysilane and tetraethylorthosilicate. Nanoporous SiO₂ matrix (NPSM), hollow SiO₂ nanotubes (HSNT) and nanospheres (HSNS) useful for efficient adsorption and catalytic processes were prepared by chemical dissolution of CdS–NS (size: 9–10 nm) and CdS–NR (length: 116–128 nm and width: 6–11 nm) template from SiO₂@CdS with 2 M HNO₃. These SiO₂ nanostructures were characterized by optical absorption, TEM, EDX, SAED and BET surface area analysis. TEM images revealed the fabrication of slightly distorted HSNS (size: 9–12 nm) and closed HSNT (length: 30–45 nm and diameter: 9–14 nm) of shorter dimensions than the CdS–NR template used. The BET surface area (112–134 m² g^?1) of NPSM and HSNS is found to be larger than the surface area (29–51 m² g^?1) of SiO₂@CdS composites indicating hollow SiO₂ morphology. Silica coated Au (SiO₂@Au) composites formed by CdS dissolution from Au (2 wt%) deposited CdS–NR core-encapsulated into SiO₂ shell (SiO₂@Au–CdS–NR) exhibited a surface plasmon band at 550 nm and displayed high catalytic activity for 4-nitrophenol reduction by Au nanoparticle.     

以碳酸钙为模板制备不同形貌的SiO_2中空粒子

以粒径1μm左右的球形和斜方碳酸钙为模板,制备了不同形貌的SiO2中空粒子。通过SEM,TEM,XRD,BET,TGA等对模板和中空粒子的结构和性能进行了表征,对包覆机理进行了探讨。结果表明:由于碳酸钙对壳层具有良好的物理支撑作用和化学亲和作用,SiO2中空粒子不仅结构完整,孔径分布良好,而且准确地复制了模板表面的细微结构。该方法操作简便,成本低廉,适合于工业化生产。     

Preparation of poly(methyl methacrylate)/CaCO3/SiO2 composite particles via emulsion polymerization

A novel method to prepare organic/inorganic composite particles, i.e. poly(methyl methacrylate)/CaCO₃/SiO₂ three-component composite particles, using emulsion polymerization of methyl methacrylate with sodium lauryl sulfate as a surfactant in an aqueous medium was reported. CaCO₃/SiO₂ two-component inorganic composite particles were obtained firstly by the reaction between Na₂CO₃ and CaCl₂ in porous silica (submicrometer size) aqueous sol and the specific surface area of the particles was measured by the Brunauer–Emmett–Teller (BET) method. The results show that the BET specific surface area of the CaCO₃/SiO₂ composite particle is much smaller than that of the silica particle, indicating that CaCO₃ particles were adsorbed by porous silica and that two-component inorganic composite particles were formed. Before copolymerization with methyl methacrylate, the inorganic composite particles were coated with a modifying agent through covalent attachment. The chemical structures of the poly(methyl methacrylate)/CaCO₃/SiO₂ composite particles obtained were characterized by Fourier transform IR spectroscopy and thermogravimetric analysis. The results show that the surface of the modified inorganic particles is grafted by the methyl methacrylate molecules and that the grafting percentage is about 15.2%.     

Thermal Preparation and Application of a Novel Silicon Fertilizer Using Talc and Calcium Carbonate as Starting Materials

The deficiency of available silicon (Si) incurred by year-round agricultural and horticultural practices highlights the significance of Si fertilization for soil replenishment. This study focuses on a novel and economical route for the synthesis of Si fertilizer via the calcination method using talc and calcium carbonate (CaCO₃) as starting materials. The molar ratio of talc to CaCO₃ of 1:2.0, calcination temperature of 1150 °C and calcination time of 120 min were identified as the optimal conditions to maximize the available Si content of the prepared Si fertilizer. X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR) characterizations elucidate the principles of the calcination temperature-dependent microstructure evolution of Si fertilizers, and the akermanite Ca₂Mg(Si₂O₇) and merwinite Ca₃Mg(SiO₄)₂ were identified as the primary silicates products. The results of release and solubility experiments suggest the content of available metallic element and slow-release property of the Si fertilizer obtained at the optimum preparation condition (Si-OPC). The surface morphology and properties of Si-OPC were illuminated by the results of scanning electron microscope (SEM), surface area and nitrogen adsorption analysis. The acceleration action of CaCO₃ in the decomposition process of talc was demonstrated by the thermogravimetry-differential scanning calorimetry (TG-DSC) test. The pot experiment corroborates that 5 g kg⁻¹ soil Si-OPC application sufficed to facilitate the pakchoi growth by providing nutrient elements. This evidence indicates the prepared Si fertilizer as a promising candidate for Si-deficient soil replenishment.     

Nano-silica and SiO2/CaCO3 nanocomposite prepared from semi-burned rice straw ash as modified papermaking fillers

Silica (SiO₂) nanoparticles and silica/calcium carbonate (SiO₂/CaCO₃) core–shell nanocomposites were prepared by sol–gel technique as fillers for papermaking application. Semi-burned rice straw ash (SBRSA), as waste material, was used to prepare the targeted fillers. Preparation of SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites was carried out using Na₂SiO₃ solution that was prepared from SBRSA and CaCO₃ nanoparticles of 30–70 nm. The targeted SiO₂/CaCO₃ nanocomposites were prepared with different molar ratio of SiO₂:CaCO₃ 1:15, 1:10 and 1:5. The percentage of silica increased from 62.5% to 82.9% by thermal treatment of SBRSA at 800 °C for 2 h. The prepared SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites were characterized by using XRD, XRF, TEM, FT-IR and Zeta potential. The results indicate that a pure semi-crystalline SiO₂ nanoparticle and semi-crystalline shell of SiO₂ coated CaCO₃ core particles were produced. The work extended also to investigate the effect of the prepared fillers on physical, mechanical and optical properties of paper.Application of the prepared SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites improved the optical properties of paper (brightness, whiteness and opacity) but it slightly reduced the mechanical properties when compared to commercial precipitated CaCO₃ (PCC) filler.The results showed that the retention of SiO₂ nano-particles was highly increased. The retention of the prepared nanocomposites increased along with increasing of SiO₂:CaCO₃ molar ratio.     

Core-shell structured nanospheres with mesoporous silica shell and Ni core as a stable catalyst for hydrolytic dehydrogenation of ammonia borane

Core-shell structured nanospheres with mesoporous silica shell and Ni core (denoted as Ni@meso-SiO₂) are prepared through a three-step process. Monodispersed Ni precursors are first prepared, and then coated with mesoporous SiO₂. Final Ni@meso-SiO₂ spheres are obtained after calcination. The products are characterized by X-ray powder diffraction, transmission electron microscopy and N₂ adsorption-desorption methods. These spheres have a high surface area and are well dispersed in water, showing a high catalytic activity with a TOF value of 18.5, and outstanding stability in hydrolytic dehydrogenation of ammonia borane at room temperature.     

中空纳米二氧化硅复合微球的制备及其对蛋白的亲和分离

利用水热法合成了中空巯基纳米二氧化硅微球(SiO₂-SH), 然后在其表面修饰亚氨基二乙酸基团(-IDA), 形成了中空SiO₂-SH/IDA双功能化纳米微球。利用该纳米微球表面的-SH和-IDA双功能团, 可以更多的吸附溶液中的Ni²⁺, 形成SiO₂-SH/IDA-Ni²⁺复合微球从而可以更好的分离以六聚组氨酸为标签的(His-tagged)蛋白。结果显示制备的样品对分离His-tagged蛋白具有广谱性, 并且具有较好的再生能力。     

中空纳米二氧化硅复合微球的制备及其对蛋白的亲和分离

利用水热法合成了中空巯基纳米二氧化硅微球(SiO₂-SH), 然后在其表面修饰亚氨基二乙酸基团(-IDA), 形成了中空SiO₂-SH/IDA双功能化纳米微球。利用该纳米微球表面的-SH和-IDA双功能团, 可以更多的吸附溶液中的Ni²⁺, 形成SiO₂-SH/IDA-Ni²⁺复合微球从而可以更好的分离以六聚组氨酸为标签的(His-tagged)蛋白。结果显示制备的样品对分离His-tagged蛋白具有广谱性, 并且具有较好的再生能力。     

用于木质素催化湿式氧化反应的纳米空心球钙钛矿催化剂

利用尿素辅助溶剂热法合成了一系列LaFe_xMn_1-xO₃和La_0.9Sr_0.1MnO₃纳米空心球材料,并采用X射线衍射、透射电子显微镜和物理吸附等方法对其晶相、形貌和比表面积进行了表征. 在木质素的催化湿式氧化反应(CWAO)中,该催化剂表现出比传统的柠檬酸溶胶-凝胶法制备的钙钛矿材料更高的催化活性. 这主要是由于空心球结构所致. 当T=120℃,p(O₂)=0.2MPa时,CWAO反应1h后木质素转化率超过80%. 反应后组分离子溶出量很低,表明由于钙钛矿相结构的存在,催化剂在该反应条件下非常稳定.     

SiO2 nanospheres with tailorable interiors by directly controlling Zn and NH3·H2O species in an emulsion process

SiO₂ nanospheres with tailorable interiors were synthesized by a facile one-spot microemulsion process using TEOS as silica source, wherein cyclohexane including triton X-100 and n-octanol as oil phase and Zn²⁺ or NH₃·H₂O aqueous solution as dispersive phase, respectively. The products were characterized by Scanning Electron Microscopy, Transmission Electron Microscopy and X-ray Powder Diffraction. It was suggested that the as-synthesized silica nanospheres possessed grape-stone-like porous or single hollow interior, and also found that the ammonia dosage and aging time played key roles in controlling the size and structure of silica nanospheres. Furthermore, the comparative results confirmed that in-situ zinc species [ZnO/Zn(OH)₂] acted as the temporary templates to construct grape-stone-like interior, and a simultaneously competing etching process occurred owing to the soluble Zn(NH₃)₄²⁺ complex formation while the additional excessive ammonia was introduced. With the aging time being extended, the in-situ nanocrystals tended to grow into bigger ones by Ostwald Ripening, producing single hollow interior.