La1－xSrxNi1－yFeyO3型钙钛矿双功能氧电极的电化学性能研究

采用溶胶-凝胶法制备了一系列La_1－xSr_xNi_1－yFe_yO₃ (x＝0, 0.1, 0.2, 0.5; y＝0～1.0)型的钙钛矿催化剂, 以活性碳为载体, PTFE乳液为粘接剂制备双功能氧电极. 对催化剂进行了XRD结构分析以及SEM分析和BET比表面积测量. 采用三电极体系测试了氧电极的稳态极化曲线和电化学交流阻抗谱并对其阴极极化和阳极极化的交流阻抗谱图进行分析. 通过等效电路的拟合研究了该系列双功能氧电极氧还原反应的工作机理. 实验表明对于LaNiO₃化合物, B位掺杂可显著提高催化剂的电催化性能; 电极氧还原反应的极化主要由电荷转移反应和Nernstian扩散过程造成. 通过各个电极对于催化分解H₂O₂的分解速率常数的测定得知, Ni离子对于催化H₂O₂分解反应的活性大于Fe离子, 继续在对于氧还原反应和氧析出反应都具有较高电催化活性的LaNi_0.8Fe_0.2O₃催化剂上进行A位掺杂Sr离子后显著提高了催化剂分解H₂O₂的催化活性, 主要是因为氧空位的增多和金属离子d电子含量的降低有利于催化分解H₂O₂的活性的提高, 但由于氧空位的增多导致催化剂电导率的降低, 所以其电催化活性降低了. 通过多圈循环伏安扫描的测试, 催化剂LaNi_0.8Fe_0.2O₃有很好的稳定性.     

铜物种对Cu/Fe2O3水煤气变换反应催化剂性能的影响

采用共沉淀法制备了系列铜负载量不同的Cu/Fe₂O₃水煤气变换(WGS)催化剂,并考察了铜负载量对催化剂结构和水煤气变换反应性能的影响. 结果表明,Cu/Fe₂O₃催化剂呈现出良好的水煤气反应性能,当CuO质量分数为20%时,催化剂的WGS性能最优,250 ℃时CO转化率高达97.2%,同时热稳定性也最好. 运用X射线粉末衍射(XRD)、N₂物理吸脱附和H₂程序升温还原(H₂-TPR)等手段对Cu/Fe₂O₃催化剂的物相、织构特征及还原性能进行了表征,结果表明,CuFe₂O₄物种的存在极大地改善了催化剂的还原性能和WGS反应活性. 这是由于CuFe₂O₄特殊的尖晶石结构有利于Cu微晶的稳定;同时,CuFe₂O₄在低温下即被还原为单质铜,有利于促进催化剂体系中电子的转移. 此外,通过(NH₄)₂CO₃溶液处理,研究了独立相CuO对Cu/Fe₂O₃催化剂WGS反应性能的影响,结果发现,独立相CuO的存在,有利于H原子在各组分传递,从而促进催化剂的CuFe₂O₄的还原,改善Cu/Fe₂O₃催化剂的WGS反应性能.     

ZnO/In2O3复合空心球的制备及其光电催化葡萄糖降解性能

通过葡萄糖协助的水热以及随后的退火处理两步法成功制备了系列ZnO/In₂O₃复合空心球. X射线衍射谱(XRD)表明, 经500 ℃退火制得的ZnO/In₂O₃复合空心球中ZnO以非晶态存在, 但是随着退火温度的提高, 其逐渐转变为纤锌矿结构. 场发射扫描电子显微镜(FE-SEM)和透射显微镜(TEM)结果表明, ZnO/In₂O₃复合材料具有空心球结构, 复合纳米颗粒之间结合紧密. 将ZnO/In₂O₃复合空心球组装成薄膜光电极, 研究了其光电催化降解葡萄糖的性能. 结果表明, 700 ℃退火处理的ZnO/In₂O₃复合空心球薄膜电极可产生最高的光致电流密度. 通过光致发光光谱(PL)发现, 与ZnO或In₂O₃空心球相比, ZnO/In₂O₃复合空心球的发光强度猝灭效果明显. 这是由于复合材料中晶界处产生的p-n结电场, 降低了光生电子-空穴对的复合几率, 从而使更多的光生电子可迁移到电极表面.     

Fe3O4改性的Ru/γ-Al2O3催化剂的原位液相加氢性能

采用分步浸渍法制备负载型Ru-Fe₃O₄/γ-Al₂O₃ 催化剂, 并利用透射电子显微镜(TEM)、X 射线衍射(XRD)、N₂吸附-脱附(BET)、傅里叶变换红外(FTIR)光谱与X射线光电子能谱(XPS)表征催化剂的纳米颗粒粒径分布、晶相组成、表面结构及吸附物种等性质. 将Ru-Fe₃O₄/γ-Al₂O₃催化剂用于3,4-二氯硝基苯选择性原位液相加氢反应, 考察了反应条件对催化活性的影响, 并讨论了不同制备条件下催化剂的稳定性能. 结果表明, 在473 K、液压3 MPa、原料质量分数2%, 乙醇/水体积比75:25 的反应条件下, 3,4-二氯硝基苯的转化率为100%, 3,4-二氯苯胺的选择性高达96.4%. Fe₃O₄含量对催化剂稳定性能有显著影响, 当Ru和Fe 的质量分数分别为2%和6%时, 催化剂可稳定200 h以上. 表面吸附CO与积碳是导致催化剂失活的主要原因, 以Fe₃O₄作为高效的助剂, 进行水汽转换(WGS)反应与费托合成(FTS)可移除CO, 而采用煅烧法去除表面积碳. 晶相变化与纳米颗粒的聚集可能导致催化剂部分失活, 其原因以及再生方法需进一步考察.     

M/Al2O3-CeO2（M=Pt-Ru，Ru，Pt）催化剂在甲胺催化湿式氧化中的活性与选择性

采用浸渍法制备了M/Al₂O₃-CeO₂（M=Pt-Ru,Ru,Pt）催化剂,并将其用于甲胺的催化湿式氧化反应（CWAO）.结果表明,Pt-Ru/Al₂O₃-CeO₂具有最佳活性和选择性.运用程序升温还原、X射线光电子能谱、X射线衍射、透射电子显微镜、N₂吸附和CO化学吸附等技术对催化剂的物化性质进行了表征.Pt组分的引入可有效提高双金属催化剂活性组分的分散度,从而明显提高了其催化性能.升降温过程中总有机碳（TOC）转化率与N₂选择性迟滞效应表明,甲胺CWAO遵循化学吸附-脱附机理.     

La1－xSrxNi1－yFeyO3型钙钛矿双功能氧电极的电化学性能研究

采用溶胶-凝胶法制备了一系列La_1－xSr_xNi_1－yFe_yO₃ (x＝0, 0.1, 0.2, 0.5; y＝0～1.0)型的钙钛矿催化剂, 以活性碳为载体, PTFE乳液为粘接剂制备双功能氧电极. 对催化剂进行了XRD结构分析以及SEM分析和BET比表面积测量. 采用三电极体系测试了氧电极的稳态极化曲线和电化学交流阻抗谱并对其阴极极化和阳极极化的交流阻抗谱图进行分析. 通过等效电路的拟合研究了该系列双功能氧电极氧还原反应的工作机理. 实验表明对于LaNiO₃化合物, B位掺杂可显著提高催化剂的电催化性能; 电极氧还原反应的极化主要由电荷转移反应和Nernstian扩散过程造成. 通过各个电极对于催化分解H₂O₂的分解速率常数的测定得知, Ni离子对于催化H₂O₂分解反应的活性大于Fe离子, 继续在对于氧还原反应和氧析出反应都具有较高电催化活性的LaNi_0.8Fe_0.2O₃催化剂上进行A位掺杂Sr离子后显著提高了催化剂分解H₂O₂的催化活性, 主要是因为氧空位的增多和金属离子d电子含量的降低有利于催化分解H₂O₂的活性的提高, 但由于氧空位的增多导致催化剂电导率的降低, 所以其电催化活性降低了. 通过多圈循环伏安扫描的测试, 催化剂LaNi_0.8Fe_0.2O₃有很好的稳定性.     

偏硼酸锶/碳酸锶复合催化剂光催化还原CO2生成CH4的研究

采用溶胶-凝胶法制备出SrB₂O₄和SrCO₃复合催化剂(SrB₂O₄/SrCO₃). 紫外光催化还原CO₂生成CH₄的实验证明, SrB₂O₄/SrCO₃复合催化剂的光催化活性已超过SrB₂O₄和TiO₂(P25)催化剂. 利用X 射线电子衍射(XRD)谱、透射电子显微镜(TEM)和等温氮气吸附-脱附分析确定了催化剂的晶相结构、粒子尺寸和比表面积.利用紫外-可见(UV-Vis)漫反射吸收光谱、X射线光电子能谱(XPS)的价带谱和荧光光谱(PL)确定了催化剂的能带结构, 结果表明: SrB₂O₄/SrCO₃复合催化剂异质结构有利于光生载流子的分离, 从而抑制了光生电子和光生空穴的复合, 提高了光生电子和光生空穴在固液界面参加光催化反应的利用率. 因此, SrB₂O₄/SrCO₃复合催化剂的紫外光催化活性得到了有效的提高.     

硫与Mn2O3空心球的复合结构及其在锂硫电池中的应用

在水热条件下,以碳球为模板合成了Mn₂O₃空心球,并用作锂硫电池的载硫基底材料。测试结果表明载硫量为51%的Mn₂O₃-S复合材料显示了较高的比容量,良好的循环稳定性和倍率性能。循环100圈后,最终可逆容量仍保持657 mA·g^-1,证明该Mn₂O₃空心球是一种有潜力的载硫基底材料。     

硫与Mn2O3空心球的复合结构及其在锂硫电池中的应用

在水热条件下,以碳球为模板合成了Mn₂O₃空心球,并用作锂硫电池的载硫基底材料。测试结果表明载硫量为51%的Mn₂O₃-S复合材料显示了较高的比容量,良好的循环稳定性和倍率性能。循环100圈后,最终可逆容量仍保持657 mA·g^-1,证明该Mn₂O₃空心球是一种有潜力的载硫基底材料。     

镧钴镍复合氧化物催化剂的制备及催化甲烷燃烧活性研究

采用共沉淀法制备LaNi_1-xCo_xO₃系列催化剂(x=0,0.2,0.4,0.6,0.8,1.0),研究B位离子Co的掺杂对单钙钛矿LaNiO₃催化甲烷燃烧性能的影响。通过X射线衍射(XRD)、比表面积测定(BET)、程序升温还原(H₂-TPR)、扫描电镜(SEM)、热重分析(TG-DSC)等实验技术对催化剂的结构和性能进行考察,以催化甲烷燃烧为目标,考察其对催化剂性能的影响。研究结果表明：Co离子的掺杂会改变单钙钛矿的晶型结构,改善催化活性,当x=0.8时,LaNi_0.2Co_0.8O₃的催化甲烷燃烧活性最好,其比表面积为22.4 m^₂.g^_-1,T_10%(起燃温度)为475℃,T_90%(完全转化温度)为610℃,反应活化能最小,为91.4KJ/mol。     

g-C3N4/双钙钛矿复合材料的制备及氧催化性能

通过溶胶-凝胶法制备出不同Ni掺杂比例的双钙钛矿Sr_2Ni_xCo_(2-x)O_6(x=0.2,0.4,0.6,0.8),通过热分解法制备出具有层状结构的纳米颗粒g-C_3N_4,并制备其复合物催化剂。将双钙钛矿和g-C_3N_4分别制备成双功能电极片,用于测试其对氧还原(ORR)和氧析出(OER)的催化活性,然后选取具有最佳氧催化活性的Ni掺杂比例x=0.4的双钙钛矿与一定重量比例的g-C_3N_4进行复合,测试复合催化剂的氧催化活性。结果表明,复合后的催化剂催化效果明显优于单一催化剂,当g-C_3N_4添加量占双钙钛矿的30%(w/w)时复合催化剂催化氧还原反应的最大电流密度为395.7 mA·cm~(-2)(-0.6 V vs Hg/HgO),氧析出反应的最大电流密度为372.0mA·cm~(-2)(1 V vs Hg/HgO),这表明g-C_3N_4与Sr_2Ni_(0.4)Co_(1.6)O_6复合后协同催化能够提高双钙钛矿的氧催化活性。     

Chirally Functionalized Hollow Nanospheres Containing L‐Prolinamide: Synthesis and Asymmetric Catalysis

Chirally functionalized hollow nanospheres with different surface properties were successfully synthesized by co‐condensation of (2S,1′R,2′R)‐N‐tert‐butyloxycarbonylpyrrolidine‐2‐carboxylic acid [2′‐(4‐trimethoxysilylbenzylamide)cyclohexyl] amide with 1,2‐bis(trimethoxysilyl)ethane or tetramethoxysilane using F127 (EO₁₀₆PO₇₀EO₁₀₆) as surfactant in water. The TEM and N₂ sorption characterizations show that the particle size of the hollow nanosphere is 15–21 nm with a core diameter of 10–16 nm. These L ‐prolinamide‐functionalized hollow nanospheres are highly efficient solid catalysts for the direct asymmetric aldol reaction between cyclohexanone and aromatic aldehydes. It was found that the addition of water in the reaction system not only enhanced the catalytic activity but also increased the enantioselectivity, which is probably due to the enhanced hydrogen bond between the amide oxygen atom and the hydroxyl group of water. Moreover, the catalytic activity increases sharply as the surface hydrophobicity of the hollow nanospheres increases. These hollow nanospheres are quite stable and can be reused with almost the same enantioselectivity and only a slight decrease in catalytic activity.     

多孔朵状Fe_3O_4纳米微球的制备及其性能研究

<正>众所周知,纳米材料的尺寸大小、晶型、形貌构型等结构特征对材料的化学物理性能有重要的影响[1],由于特殊形貌的新材料所具有独特、新颖、高效的化学物理等方面的性质以及在众多领域中的潜在应用[2],特别是3D花状空心纳米结构新物质[3-4],新形貌物质的纳米材料的制备方法和应用特性已经吸引了世界上材料领域的广泛兴趣和关注[5]。目前为止,合成3D纳米结构的方法有自组装法、三维导向连接法以及水热法等,即通过使用有     

Effect of the support on cobalt carbide catalysts for sustainable production of olefins from syngas

Co₂C-based catalysts with SiO₂, γ-Al₂O₃, and carbon nanotubes (CNTs) as support materials were prepared and evaluated for the Fischer-Tropsch to olefin (FTO) reaction. The combination of catalytic performance and structure characterization indicates that the cobalt-support interaction has a great influence on the Co₂C morphology and catalytic performance. The CNT support facilitates the formation of a CoMn composite oxide during calcination, and Co₂C nanoprisms were observed in the spent catalysts, resulting in a product distribution that greatly deviates from the classical Anderson-Schulz-Flory (ASF) distribution, where only 2.4 C% methane was generated. The Co₃O₄ phase for SiO₂- and γ-Al₂O₃-supported catalysts was observed in the calcined sample. After reduction, CoO, MnO, and low-valence CoMn composite oxide were generated in the γ-Al₂O₃-supported sample, and both Co₂C nanospheres and nanoprisms were identified in the corresponding spent catalyst. However, only separated phases of CoO and MnO were found in the reduced sample supported by SiO₂, and Co₂C nanospheres were detected in the spent catalyst without the evidence of any Co₂C nanoprisms. The Co₂C nanospheres led to a relatively high methane selectivity of 5.8 C% and 12.0 C% of the γ-Al₂O₃- and SiO₂-supported catalysts, respectively. These results suggest that a relatively weak cobalt-support interaction is necessary for the formation of the CoMn composite oxide during calcination, which benefits the formation of Co₂C nanoprisms with promising catalytic performance for the sustainable production of olefins via syngas.     

Effects of the partial replacement of La by M (M=Ce, Ca and Sr) in La2-xMxCuO4 perovskites on catalysis of the water-gas shift reaction

The performance of La2-xMxCuO4 perovskites (where M = Ce, Ca or Sr) as catalysts for the water-gas shift reaction was investigated at 290 ℃ and 360 ℃. The catalysts were characterized by EDS, XRD, N2 adsorption-desorption, XPS and XANES. The XRD results showed that all the perovskites exhibited a single phase (the presence of perovskite structure), suggesting the incorporation of metals in the perovskite structure. The XPS and XANES results showed the presence of Cu²⁺ on the surface. The perovskites that exhibited the best catalytic performance were La2-xCexCuO4 perovskites, with CO conversions of 85%-90%. Moreover, these perovskites have higher surface areas and larger amounts of Cu on the surface. And Ce has a higher filled energy level than the other metals, increasing the energy of the valence band of Ce and providing more electrons for the reaction. Besides, the La1.80Ca0.20CuO4 perovskite showed a good catalytic performance.     

La2−xCexCu1−yZnyO4 perovskites for high temperature water-gas shift reaction

The performance of La_2−xCe_xCu_1−yZn_yO₄ perovskites as catalysts for the high temperature water-gas shift reaction (HT-WGSR) was investigated. The catalysts were characterized by EDS, XRD, BET surface area, TPR, and XANES. The results showed that all the perovskites exhibited the La₂CuO₄ orthorhombic structure, so the Pechini method is suitable for the preparation of pure perovskite. However, the La_1.90Ce_0.10CuO₄ perovskite alone, when calcined at 350/700 °C, also showed a (La_0.935Ce_0.065)₂CuO₄ perovskite with tetragonal structure, which produced a surface area higher than the other perovskites. The perovskites that exhibited the best catalytic performance were those calcined at 350/700 °C and, among these, La_1.90Ce_0.10CuO₄ was outstanding, probably because of the high surface area associated with the presence of the (La_0.935Ce_0.065)₂CuO₄ perovskite with tetragonal structure and orthorhombic La₂CuO₄ phase.     

BaTiO3 and PbTiO3 perovskite as catalysts for methane combustion

Unsupported and γ-Al₂O₃-supported Ba and Pb titanate catalysts were prepared, characterized and studied in the combustion of methane, as a test reaction for VOCs’ catalytic combustion. They present good catalytic activities, and after dispersion (5%) on γ-Al₂O₃ the specific activity of the supported perovskite phase increased 25 and 30 times, respectively, compared with the unsupported samples. PbTiO₃/γ-Al₂O₃ shows the best catalytic properties among the tested samples.     

Preparation of carbon supported Pd–Pb hollow nanospheres and their electrocatalytic activities for formic acid oxidation

Pd–Pb hollow nanospheres dispersed on carbon black were developed by a galvanic replacement reaction between sacrificial cobalt nanoparticles and Pd²⁺, Pb²⁺ ions. The as-prepared catalysts were characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). The electrochemical measurements show that the as-prepared catalysts have excellent catalytic activity for formic acid electrooxidation, which is attributed to the large surface area caused by the hollow structure and the lead doping effect which might modify the electronic structure of the catalysts.     

反应条件对乳液法自组装合成氧化锰纳米粒子结构、形貌和尺寸的影响

通过改变反应物物质的量比、分散相与连续相体积比、反应体系温度和煅烧后处理温度,研究了反应条件对乳液法自组装合成氧化锰纳米粒子结构、形貌和尺寸的影响.结果表明:当高锰酸钾与油酸物质的量比在1∶5～1∶1之间时,形成蜂窝状纳米粒子和空心纳米粒子;当分散相(油酸)与连续相(水)的体积比为4∶200时,形成良好的空心球纳米结构;反应体系温度升高不利于产物的洗涤;不同温度的煅烧后处理不仅影响氧化锰纳米粒子的形貌,而且影响其结晶度和晶型.