掺铝Co_3O_4的制备及其电容性能研究

以KOH作沉淀剂制备掺杂Al(Ⅲ)的Co3O4粉体.X射线衍射显示,掺Al的Co3O4不改变其晶型结构.循环伏安、恒流充放电等测试表明,化学掺Al后的Co3O4电极,其比容量提高,当Co(Ⅱ)与Al(Ⅲ)的摩尔比为1∶0.05时,在0~400 mV的电位区间内,5 mA/cm2电流密度下,单电极放电比容量可达518.07 F/g.     

锂钛复合氧化物锂离子电池负极材料的研究

采用 3种化学方法合成锂钛复合氧化物 .应用X -射线衍射分析对其结构进行表征以及电化学性能测试 ,结果表明 :由Li2 CO3、TiO2 高温合成的锂钛复合氧化物为尖晶石结构的Li4Ti5 O12 .Li4Ti5 O12 电极在 1 .5V左右有一放电平台 ,充放电可逆性良好 ,即充电电压平台与此接近 ,且电极的比容量较大 ,循环性能良好 .以 0 .30mA·cm- 2 充放电时 ,首次放电容量可达 30 0mAh·g- 1,可逆比容量为 1 0 0mAh·g- 1,经多次充放电循环后 ,其结构仍保持稳定性 .试验电池测试表明 ,Li4Ti5 O12 可选作Li4Ti5 O12 /LiCoO2 锂离子电池的负极材料 .     

锌掺杂提高LiNi1/3Co1/3Mn1/3O2正极材料的电化学稳定性

通过共沉淀法与固相法相结合制备了掺锌的高稳定性Li(Ni1/3Co1/3Mn1/3)1-xZnxO2(x=0,0.02,0.05)正极材料.循环伏安(CV)曲线表明Zn掺杂使氧化峰与还原峰的电势差减小到0.09 V,电化学阻抗谱(EIS)曲线表明Zn掺杂使电极的阻抗从266Ω减小到102Ω. Li+嵌入扩散系数从1.20×10-11 cm2·s-1增大到2.54×10-11 cm2· s-1. Li(Ni1/3Co1/3Mn1/3)0.98Zn0.02O2正极材料以0.3C充放电在较高的截止电压(4.6 V)下比其他两种材料的电化学循环性能更稳定,其第二周的放电比容量为176.2 mAh·g-1,室温下循环100周后容量几乎没衰减;高温(55°C)下充放电循环100周,其放电比容量平均每周仅衰减0.20%,远小于其他两种正极材料(LiNi1/3Co1/3Mn1/3O2平均每周衰减0.54%;Li(Ni1/3Co1/3Mn1/3)0.95Zn0.05O2平均每周衰减0.38%). Li(Ni1/3Co1/3Mn1/3)0.98Zn0.02O2正极材料以3C充放电时其放电比容量可达142 mAh·g-1,高于其他两种正极材料.电化学稳定性的提高归因于Zn掺杂后减小了电极的极化和阻抗,增大了锂离子扩散系数     

锂离子正极材料Li(Ni_(1/3)Co_(1/3)Mn_(1/3))_(1-x)Al_xO_2的制备及电化学性能

以化学法合成Li(Ni1/3Co1/3Mn1/3)1-xAlxO2系列正极材料(0≤x≤0.1);用X射线衍射仪、扫描电子显微镜和充放电仪研究系列产物的晶体微观结构、表面形貌以及电化学性能,研究不同Al含量参杂对材料性能的影响。结果表明,合成的材料均属于六方晶系,R3m空间群,保持α-NaFeO2层状结构相;Li(Ni1/3Co1/3Mn1/3)0.95Al0.05O2的首次放电容量166.30 mA·h/g,在2.5~4.5 V区间60次循环后比容量衰竭率为4.43%。通过对比Li(Ni1/3Co1/3Mn1/3)0.95Al0.05O2和Li(Ni1/3Co1/3Mn1/3)O2的电极阻抗,分析它们的电化学循环机理,可知掺杂Al后的正极材料适合大倍率放电。     

液相法合成锂离子电池正极材料Li_(1+x)Mn_2O_4

采用柠檬酸络合和溶液浸渍两种方法制备Li1+xMn2 O4正极材料 ,用XRD和BET测试了材料晶体结构和比表面积 ,考察焙烧温度、Li/Mn比、起始原料对产物结构和电化学性能的影响 ,结果表明 ,焙烧温度与Li/Mn比是影响材料电化学性能的关键因素 ,确定了制备Li1+xMn2 O4材料最佳条件为 0≤x≤ 0 .0 5 ,焙烧温度 75 0°C ,所得电池材料首次充放电容量达到 1 2 0mAh/g .循环 5 0次后 ,其充放电容量为 1 1 5mAh/g .     

Al掺杂尖晶石LiMn2O4正极材料的性能

尖晶石LiMn2O4作为锂离子电池正极可大电流放电,且成本低、环境友好.采用溶胶-凝胶法制备尖晶石LiMn2O4及Al掺杂材料.使用X-射线衍射(XRD)和扫描电子显微镜(SEM)观察材料结构与形貌.结果表明,复合材料颗粒尺寸300-500 nm,呈类球形.电化学恒流充放电测试表明,Al掺杂尖晶石LiMn2O4电极的循环性明显提高,Al掺杂5%LiMn2O4(by mass,下同)正极在1C倍率充放电100周期循环后的容量保持率为98.2%,1C倍率充电、5C倍率放电下,100周期循环后其容量保持率为99.0%,表现出较优的电化学循环性能.     

LiNi_(0.8)Co_(0.2)O_2的络合法合成及其电化学性能研究

采用络合法制备了锂离子电池的活性正极材料LiNi0.8Co0.2O2粉体,该合成材料结晶良好,层状结构发育完善.电池充放电测试表明,作为锂离子电池正极,其电化学性能与LiNi0.8Co0.2O2粉体的合成温度有关,其中以900℃下合成得到的材料性能最优:第1次放电比容量高达142mAh/g,循环30次后可逆比容量仍高达122mAh/g,容量损失为14.5%.文中对容量退化的原因进行了分析.     

锂离子电池正极材料LiV3-xAlxO8的水热合成与性能

采用水热法制备了Al掺杂的锂二次电池正极材料LiV3-xAlxO8,并用X射线衍射和扫描电镜对材料的晶体结构和形貌进行了表征.以50 mA·g-1进行恒流充放电测试,结果表明Al掺杂能够明显改善材料的电化学性能.在掺杂改性的LiV3-xAlxO8材料中,LiV2.93Al0.07O8的初始容量最高,达到325 mAh·g-1.当掺杂量为x=0.04时,材料的循环性能最佳.LiV2.96Al0.04O8经20次循环后仍保持179 mAh·g-1的比容量,且充放电效率始终维持在98%左右.     

锂离子电池正极材料Li_(1.2)Mn_(0.54-x)Ni_(0.13)Co_(0.13)Zr_xO_2的制备及电化学性能

为了改善富锂锰基正极材料Li1.2Mn0.54Ni0.13Co0.13O2的循环性能,采用燃烧法合成了正极材料Li1.2Mn0.54-xNi0.13Co0.13ZrxO2(x=0.00,0.01,0.02,0.03,0.06).通过X射线衍射(XRD)和扫描电镜(SEM)对其结构与形貌进行了表征,利用恒电流充放电测试,循环伏安(CV)及电化学交流阻抗谱(EIS)技术对其电化学性能进行测试.结果表明,Li1.2Mn0.54-xNi0.13Co0.13ZrxO2(x=0.00,0.01,0.02,0.03,0.06)正极材料均具有α-NaFeO2型层状结构;在室温,2.0-4.8 V电压范围,以0.1C和1.0C(充放电电流以1.0C=180 mA·g-1计算)倍率充放电进行测试,样品Li1.2Mn0.52Ni0.13Co0.13Zr0.02O2的首次放电比容量分别为280.3和206.4 mAh·g-1.其中,在1.0C倍率下,100次循环后容量保持率由原来的73.2%提高到88.9%;以5.0C倍率充放电进行测试,经50次循环后,掺杂正极材料的放电比容量为76.5 mAh·g-1,而未掺杂材料仅有15.0 mAh·g-1.在50、25和-10°C,2.0C倍率条件下,掺杂正极材料的电化学性能均得到有效改善,其中,在-10°C经过50次循环后正极材料Li1.2Mn0.52Ni0.13Co0.13Zr0.02O2比未掺杂的正极材料相比,其放电比容量提高了61.1%.     

YF3包覆Li(Li0.22Ni0.17Mn0.61)O2正极材料的性能

富锂层状氧化物作为锂离子电池正极材料具有高比容量优势.采用草酸盐共沉淀法制备Li(Li0.22Ni0.17Mn0.61)O2,并用YF3包覆电极.采用X射线衍射(XRD)、扫描电子显微镜(SEM)和X射线能谱分析(EDS)表征材料结构、观察材料形貌.结果表明,材料颗粒尺寸在100～200 nm范围,YF3包覆不会改变材料结构和形貌.电化学恒流充放电测试表明,YF3包覆Li(Li0.22Ni0.17Mn0.61)O2电极的比容量,尤其倍率比容量明显提高.60 mA·g-1电流密度下包覆电极材料30周循环后其比容量保持在220 mAh·g-1以上,1500 mA·g-1电流密度下其比容量仍可达150 mAh·g-1.电化学阻抗谱(EIS)测试结果表明,YF3包覆电极电荷转移电阻和扩散阻抗均明显降低,有利于电化学性能改善.     

锌掺杂提高LiNi1/3Co1/3Mn1/3O2正极材料的电化学稳定性

通过共沉淀法与固相法相结合制备了掺锌的高稳定性Li(Ni_1/3Co_1/3Mn_1/3)_1-xZn_xO₂ (x=0, 0.02, 0.05)正极材料. 循环伏安(CV)曲线表明Zn掺杂使氧化峰与还原峰的电势差减小到0.09 V, 电化学阻抗谱(EIS)曲线表明Zn掺杂使电极的阻抗从266 Ω减小到102 Ω. Li⁺嵌入扩散系数从1.20×10^-11 cm²·s^-1增大到 2.54×10^-11 cm²·s^-1. Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以0.3C充放电在较高的截止电压(4.6 V)下比其他两种材料的电化学循环性能更稳定, 其第二周的放电比容量为176.2 mAh·g^-1, 循环100周后容量几乎没衰减; 高温(55 °C)下充放电循环100周, 其放电比容量平均每周仅衰减0.20%, 远小于其他两种正极材料(LiNi_1/3Co_1/3Mn_1/3O₂平均每周衰减0.54%; Li(Ni_1/3Co_1/3Mn_1/3)_0.95Zn_0.05O₂平均每周衰减0.38%). Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以3C充放电时其放电比容量可达142 mAh·g^-1, 高于其他两种正极材料. 电化学稳定性的提高归因于Zn掺杂后减小了电极的极化和阻抗, 增大了锂离子扩散系数.     

Detailed studies of a high-capacity electrode material for rechargeable batteries, Li2MnO3-LiCo(1/3)Ni(1/3)Mn(1/3)O2

Lithium-excess manganese layered oxides, which are commonly described by the chemical formula zLi(2)MnO(3)-(1-z)LiMeO(2) (Me = Co, Ni, Mn, etc.), are of great importance as positive electrode materials for rechargeable lithium batteries. In this Article, Li(x)Co(0.13)Ni(0.13)Mn(0.54)O(2-δ) samples are prepared from Li(1.2)Ni(0.13)Co(0.13)Mn(0.54)O(2) (or 0.5Li(2)MnO(3)-0.5LiCo(1/3)Ni(1/3)Mn(1/3)O(2)) by an electrochemical oxidation/reduction process in an electrochemical cell to study a reaction mechanism in detail before and after charging across a voltage plateau at 4.5 V vs Li/Li(+). Changes of the bulk and surface structures are examined by synchrotron X-ray diffraction (SXRD), X-ray absorption spectroscopy (XAS), X-ray photoelectron spectroscopy (XPS), and time-of-flight secondary ion mass spectroscopy (SIMS). SXRD data show that simultaneous oxygen and lithium removal at the voltage plateau upon initial charge causes the structural rearrangement, including a cation migration process from metal to lithium layers, which is also supported by XAS. This is consistent with the mechanism proposed in the literature related to the Li-excess manganese layered oxides. Oxygen removal associated with the initial charge on the high voltage plateau causes oxygen molecule generation in the electrochemical cells. The oxygen molecules in the cell are electrochemically reduced in the subsequent discharge below 3.0 V, leading to the extra capacity. Surface analysis confirms the formation of the oxygen containing species, such as lithium carbonate, which accumulates on the electrode surface. The oxygen containing species are electrochemically decomposed upon second charge above 4.0 V. The results suggest that, in addition to the conventional transition metal redox reactions, at least some of the reversible capacity for the Li-excess manganese layered oxides originates from the electrochemical redox reaction of the oxygen molecules at the electrode surface.     

Studies on Synthesis and Electrochemical Performance of Li1+δNi1-xCoxO2-yFy Cathode Materials for Lithium-ion Rechargeable Batteries

It is a technological problem of LiNiO2 cathode material for lithium-ion secondary batteries because of the difficult preparation and hard purification, instable performance, remarkable capacity fading at initial discharge, worse thermal stability and safety of Ni-series cathode materials,and it is also the key factor of hindering LiNiO2 cathode material from practical applications.Recently, by doping some metal cations such as Co, Mn, Mg, Al, Cr and so on[1-5] into LiNiO2, the preparation difficulty and the purification hardness can be obviously improved, and the initial irreversible discharge capacity can be reduced, and the ratio of the initial discharge to charge capacity can be enhanced. But the cyclic stability, thermal stability and safety of LiNiO2 are not enough to satisfy the demand of commercial use.At present, the synthesis of LiNiO2 cathode material must be sintered under oxygen atmosphere in most cases, and the improved effect of fluoride doping on the electrochemical properties of LiNiO2 has seldom been reported in the literatures.In this paper, the cobalt cation and fluorine anion co-doping cathode materials Li1+δNi1-xCoxO2-yFy( 0≤δ≤0.2, 0≤x≤0.5, 0≤y≤0.1 ) were synthesized by solid state reaction method at 650℃ ～750℃ under air atmosphere, and characterized by XRD、 SEM、 TEM、 BET、 laser particle-size distribution measurement and electrochemical performance testing, the effect of different nickel sources on the properties of as-synthesized cathode materials was investigated. The results demonstrated that the cobalt and fluorine ions co-doping cathode materials Li1+δNi1-xCoxO2-yFy have complete layered structure, uniform surface morphology and better particle-size distribution as well as excellent electrochemical performances. At 20～25℃, 0.15～0.25mA charge and discharge current,4.25～2.70V cut-off voltage, 0.2～0.5C charge and discharge rate and 0.2～0.5 mA/cm2 current density,LiNi0.8Co0.2O1.95F0.05 cathode material has higher initial charge and discharge capacity and better cyclic properties which can be mainly attributed to the doping of the higher electronegativity fluorine which improves the structural stability and the synergistic reaction of cobalt and fluorine ions co-doping on the cathode materials. Under the above conditions, the initial charge and discharge capacity of LiNi0.8Co0.2O1.95F0.05 is 165.70mAh/g and 146.10mAh/g, respectively. After 50 cycles, it has more than 140mAh/g of discharge capacity and displays preliminary application possibility in the future.     

钼掺杂Li3V2（PO4）3/C正极材料的制备及其电化学性能研究

以Li2CO3、NH4H2PO4、V2O5和MoO3为原料,柠檬酸为络合剂和碳源,采用溶胶-凝胶法制备了锂离子正极材料Li3MoxV2-x(PO4)3/C(x=0.01,0.02,0.03).X射线衍射(XRD)表明,合成的材料具有单一的单斜晶系结构,空间群为P21/n.扫描电镜(SEM)显示Li3Mo0.02V1.98(PO4)3/C具有均一的表面形貌.恒流充放电测试表明,当x=0.02时,掺杂后的Li3Mo0.02V1.98(PO4)3具有最佳的电化学性能.在1C倍率下,3.0～4.3 V电位区间,Li3Mo0.02V1.98(PO4)3/C的首次放电比容量达到122.3 mAh.g-1,循环50周之后,容量没有衰减的迹象;而当x=0、0.01和0.03时,首次放电比容量仅分别为117.1、115.1和116.0 mAh.g-1.在3C和5C倍率下,样品Li3Mo0.02V1.98(PO4)3/C仍能保持优异的循环稳定性.     

钼掺杂磷酸钒锂正极材料的制备及其电化学性能研究

以Li2CO3,NH4H2PO4,V2O5和MoO3为原料,柠檬酸为络合剂和碳源,采用溶胶凝胶法制备了锂离子正极材料Li3MoxV2-x(PO4)3/C (x = 0.01, 0.02和0.03). X射线衍射（XRD）表明,合成的材料具有单一的单斜晶系结构,空间群为P21/n. 扫描电镜（SEM）显示Li3Mo0.02V1.98(PO4)3/C具有均一的表面形貌。恒流充放电测试表明,当x = 0.02时,掺杂后的Li3Mo0.02V1.98(PO4)3具有最佳的电化学性能. 在1C倍率下,3.0 ~ 4.3 V电位区间,Li3Mo0.02V1.98(PO4)3/C的首次放电比容量达到122.3 mAh?g-1,循环50周之后,容量没有衰减的迹象;而当x = 0, 0.01和0.03时,首次放电比容量仅分别为117.1 mAh?g-1,115.1 mAh?g-1和116.0 mAh?g-1. 在3C和5C倍率下,样品Li3Mo0.02V1.98 (PO4)3/C仍能保持优异的循环稳定性.     

锂离子电池正极材料xLi2MnO3·(1-x)Li[Ni1/3Mn1/3Co1/3]O2的制备及表征

以过渡金属乙酸盐和乙酸锂为原料,柠檬酸为螯合剂,通过溶胶-凝胶法结合高温煅烧法制备了锂离子电池富锂锰基正极材料xLi2MnO3·(1-x)Li[Ni1/3Mn1/3Co1/3]O2,采用X射线衍射(XRD),扫描电子显微镜(SEM)和电化学性能测试对所得样品的结构,形貌及电化学性能进行了表征.结果表明:x=0.5时,在900°C下煅烧12h得到颗粒均匀细小的层状xLi2MnO3·(1-x)Li[Ni1/3Mn1/3Co1/3]O2材料,并具有良好的电化学性能,在室温下以20mA·g-1的电流密度充放电,2.0-4.8V电位范围内首次放电比容量高达260.0mAh·g-1,循环40次后放电比容量为244.7mAh·g-1,容量保持率为94.12%.     

新型锂离子电池正极材料Li0.86V0.8O2的水热合成及性质

采用两步反应制备了新型锂离子电池正极材料Li0.86V0.8O2. 该材料具有六方层状结构, 空间群为R3m. 研究了在水热条件下溶液的碱度对于钒酸锂盐形成的影响, 在低碱度的条件下, 前驱体V2O3和LiOH·H2O并未发生反应, 只有在碱度达到2.5 mol/L时, 才能形成单相的Li0.86V0.8O2材料. X射线光电子能谱分析发现, V2p的结合能位于516.4 和523.1 eV, 分别对应于四价钒离子的V2p3/2 和V2p1/2, 这说明在Li0.86V0.8O2中V离子主要价位为+4价. 在电流密度为7.4 mA/g的充放电中, Li0.86V0.8O2初始充电容量达到163 mA·h/g, 首次放电容量也能达到113 mA·h/g, 20次循环后放电容量仍然可以达到80 mA·h/g, 表现出较好的循环性能.     

A feasibility study on the use of Li(4)V(3)O(8) as a high capacity cathode material for lithium-ion batteries

Li(4)V(3)O(8) materials have been prepared by chemical lithiation by Li(2)S of spherical Li(1.1)V(3)O(8) precursor materials obtained by a spray-drying technique. The over-lithiated vanadates were characterised physically by using scanning electron microscopy (SEM) and X-ray diffraction (XRD), and electrochemically using galvanostatic charge-discharge and cyclic voltammetry measurements in both the half-cell (vs. Li metal) and full-cell (vs. graphite) systems. The Li(4)V(3)O(8) materials are stable in air for up to 5 h, with almost no capacity drop for the samples stored under air. However, prolonged exposure to air will severely change the composition of the Li(4)V(3)O(8) materials, resulting in both Li(1.1)V(3)O(8) and Li(2)CO(3). The electrochemical performance of these over-lithiated vanadates was found to be very sensitive to the conductive additive (carbon black) content in the cathode. When sufficient carbon black is added, the Li(4)V(3)O(8) cathode exhibits good cycling behaviour and excellent rate capabilities, matching those of the Li(1.1)V(3)O(8) precursor material, that is, retaining an average charge capacity of 205 mAh g(-1) at 2800 mA g(-1) (8C rate; 1C rate means full charge or discharge of a battery in one hour), when cycled in the potential range of 2.0-4.0 V versus Li metal. When applied in a non-optimised full cell system (vs. graphite), the Li(4)V(3)O(8) cathode showed promising cycling behaviour, retaining a charge capacity (Li(+) extraction) above 130 mAh g(-1) beyond 50 cycles, when cycled in the voltage range of 1.6-4.0 V, at a specific current of 117 mA g(-1) (C/3 rate).     

Layered manganese oxide with O2 structure,Li(2/3)+x(Ni1/3Mn2/3)O2 as cathode for Li-ion batteries

Using LiI as the reducing agent, the compound O2-Li_(2/3)+x(Ni_1/3Mn_2/3)O₂, x∼1/3 (O2(Li+x)) has been prepared from the O2-Li_2/3(Ni_1/3Mn_2/3)O₂ (O2(Li)). Cyclic voltammetry and voltage-capacity profiles of the O2(Li+x) phase are qualitatively different from that of O2(Li) phase. The first extraction capacity of O2(Li+x) at C/10 rate is 190 mAh/g corresponding to the removal of 2/3 mole of Li from the compound. At C/5 rate it delivers a reversible capacity of 158 mAh/g at 25 °C and 184 mAh/g at 50 °C (vs Li metal; voltage window 2.5–4.6 V). In Li-ion cells, with MCMB anode and O2(Li+x) as cathode, a discharge capacity of 140 mAh/g was obtained at C/5 rate in the voltage window 2.5–4.5 V (25 °C). The charge–discharge cycling performance and the cyclic voltammograms reveal that O2(Li) and O2(Li+x) do not convert to the spinel structure.