两步电泳沉积制备TiO2光阳极用于高效染料敏化太阳能电池

采用不同沉积电压制备TiO₂光阳极,研究电压对薄膜沉积速率、厚度和形貌的影响。通过台阶仪、光学照片、扫描电子显微镜(SEM)、电化学交流阻抗谱、开路电压衰减曲线对光阳极和电池进行系统表征,并测试了染料敏化太阳能电池器件的电流密度-电压(J-V)曲线,计算其光电转换效率。结果表明,提高沉积电压时,光阳极薄膜的沉积速率加快,膜厚也增加,但是电压过高时,薄膜会有裂缝和覆盖不全的问题,这会对电池的效率造成负面影响。综合考虑低沉积电压条件下薄膜均匀无裂缝和高沉积电压条件下沉积速率快的优点,采用先30 V电压、后60 V电压的电泳沉积方式来制备光阳极,结果呈现协同效果,既降低了制备时间又得到高质量的薄膜,在无其他修饰的情况下,电池的光电转换效率可以达到7.29%。     

骨架结构多孔TiO2薄膜增强染料敏化太阳能电池性能

以空心球状TiO₂为基体、以片状TiO₂为骨架,采用刮刀法制备了染料敏化太阳能电池的多孔TiO₂光阳极薄膜。光电转化效率测试结果表明,当作为骨架支撑材料的片状TiO₂含量为20wt%时,光阳极薄膜组装成太阳能电池的光电转化效率达到最高值4.53%,比商业P₂₅制备的无孔无骨架TiO₂薄膜电池(4.06%)及无骨架结构的多孔TiO₂薄膜电池(4.17%)的性能均有显著提高。当片状TiO₂的最佳含量为20wt%电池薄膜厚度为33μm时,太阳能电池光电转化效率进一步提升为7.06%。光电性能增强的原因是骨架结构有利于快速传输电子并增大染料吸附量。本研究通过设计制备具有骨架结构的多孔TiO₂薄膜为提高染料敏化太阳能电池性能提供了新的思路。     

骨架结构多孔TiO2薄膜增强染料敏化太阳能电池性能

以空心球状TiO₂为基体、以片状TiO₂为骨架,采用刮刀法制备了染料敏化太阳能电池的多孔TiO₂光阳极薄膜。光电转化效率测试结果表明,当作为骨架支撑材料的片状TiO₂含量为20wt%时,光阳极薄膜组装成太阳能电池的光电转化效率达到最高值4.53%,比商业P25制备的无孔无骨架TiO₂薄膜电池(4.06%)及无骨架结构的多孔TiO₂薄膜电池(4.17%)的性能均有显著提高。当片状TiO₂的最佳含量为20wt%电池薄膜厚度为33 μm时,太阳能电池光电转化效率进一步提升为7.06%。光电性能增强的原因是骨架结构有利于快速传输电子并增大染料吸附量。本研究通过设计制备具有骨架结构的多孔TiO₂薄膜为提高染料敏化太阳能电池性能提供了新的思路。     

表面修饰的TiO2太阳能电池界面特性研究

用水热法制备了具有典型锐钛矿晶型的TiO₂纳米材料,采用Cr(NO₃)₃对TiO₂薄膜电极进行修饰改性。用X射线衍射(XRD)、扫描电子显微镜(SEM)和光电子能谱(XPS)测试电极的物相及表面结构,结果显示TiO₂薄膜表面包覆一层粒径较大的氧化铬颗粒,整个电极仍保持均匀的多孔结构。电流-电压(Ⅰ-Ⅴ)曲线测试结果显示,改性后最佳电极的短路电流和光电转换效率分别比改性前提高了31.1%和40.4%。用电化学阻抗谱(EIS)测试电池的界面特性,从测试结果可以看出,相同偏压下,改性后电池的TiO₂/染料/电解质界面电阻更大,说明氧化铬包覆层在一定程度上抑制了界面的电子复合,改善了电池的光电输出特性。     

TiO2纳米微球的制备及在染料敏化太阳能电池中的应用

以四氯化钛、盐酸为原料,制备出花状TiO₂纳米微球,利用扫描电子显微镜（SEM）、X射线衍射（XRD）等测试方法,对样品的结构和形貌进行了表征。为了提高TiO₂微球电池的光电性能,利用TiO₂微球作为反射层构造了双层结构的薄膜电极,结果表明,双层结构染料敏化太阳能电池在100 mW·cm^-2（1.5 G）光照条件下,短路光电流J_sc为17.64 mA·cm^-2,开路光电压Voc为0.74 V,填充因子FF为0.63和光电转化效率η为8.33%。相比TiO₂微球制备的太阳能电池,双层结构染料敏化太阳能电池光电转化效率提高至5.3倍。最后对电极中染料的吸附量、电极的光散射性能和电池的电化学阻抗做了进一步研究和分析,研究表明,双层结构电池增强光的捕获能力,从而提高光伏性能。     

表面活性剂对染料敏化太阳能电池光电性能的提高

在硝酸/醋酸(HNO₃/HAc)的水溶液中分别加入十二烷基苯磺酸钠(DBS)、十六烷基三甲基溴化铵(CTAB)、吐温20等不同类型的表面活性剂来水解钛酸四正丁酯制得前驱体溶液,通过水热法制备纳晶TiO₂,并组装成染料敏化太阳能电池(DSSC)。通过XRD、SEM和UV-Vis对纳晶TiO₂薄膜进行表征,并对DSSC进行光电流-光电压(I-V)曲线的测试,研究了不同类型的表面活性剂和不同浓度的CTAB对DSSC光电性能的影响。结果表明：加入阳离子表面活性剂CTAB时提高了DSSC的光电性能,而加入阴离子表面活性剂DBS和非离子表面活性剂吐温20时,DSSC的光电性能反而降低。随着CTAB浓度的增加,电池的光电性能先提高后下降,当c_CTAB=0.08 mol·L^-1时,DSSC的光电转化效率最高为5.76%,比不添加表面活性剂制备的纳晶TiO₂所组装的DSSC的光电转化效率提高了约18%。     

低温吸附制备Au-TiO2复合薄膜及其光电化学性质

在低温条件下将预先合成的Au溶胶吸附到TiO₂薄膜上以制备纳米Au-TiO₂复合薄膜,以超高分辨率场发射扫描电镜(FESEM)、X射线衍射(XRD)及X射线光电子能谱(XPS)表征Au-TiO₂膜,并在UV辐照下测定了Au-TiO₂薄膜电极的光电化学性质。纳米Au呈金属态,平均粒径为(4.3±1.2) nm,负载量高,均匀地沉积于TiO₂薄膜表面。光电化学测试表明,沉积纳米Au后,TiO₂电极的光生电流提高近5倍,光生电压明显向负值增大,说明纳米Au可增强光生载流子的分离效率,促进电荷在电极与溶液界面间的转移。Au-TiO₂电极的电荷传递法拉第阻抗(R_ct)是TiO₂电极的一半,说明负载的纳米Au粒抑制了光生电子-空穴的复合,提高了电极中载流子浓度。     

光电沉积Co-Pi对Ta3N5水分解性能的影响及机理

Co-Pi是一种低廉高效的氧化水产氧助催化剂,助催化剂担载方法及条件是光阳极太阳能水分解效率的提升的关键因素之一。以光阳极材料Ta₃N₅为基底,针对光电沉积担载助催化剂Co-Pi开展了一系列研究,研究表明光电沉积Co-Pi过程中,照射光强的影响较小,而外加偏压和担载电量的影响很大,是Co-Pi担载的关键因素;通过阻抗谱测试定量分析了Co-Pi担载条件对Ta₃N₅/电解液界面载流子输运的影响,表明Co-Pi担载电压和电量直接影响界面光生载流子的传输,进而决定了Ta₃N₅水分解性能的高低;发现最优担载偏压对不同的Ta₃N₅均适用,而最优担载电量和光阳极的表面粗糙度存在正相关关系,要针对光阳极表面粗糙度调节助催化剂担载条件。     

室温下制备以{211}晶面为主的Ti1-xVxO2薄膜及其可见光催化性能

以金属Ti和V作为靶材,采用直流反应共溅射技术在室温下制备了以{211}晶面为主的锐钛矿相Ti_1-xV_xO₂薄膜,研究了不同V靶功率对Ti_1-xV_xO₂薄膜的薄膜成分、晶相结构和可见光催化性能的影响。研究表明,Ti_1-xV_xO₂薄膜的晶相结构为锐钛矿相,择优取向为(211),而结晶度受V靶功率的影响。随着V靶功率的增加,薄膜中V元素含量逐渐增加,同时,晶粒和沉积速率也逐渐增加。另外,当V靶功率为150 W时,薄膜的表面粗糙度值有一个最大值。V的掺杂导致薄膜的能带间隙变窄,对光的吸收向可见光区偏移,从而有效地改善了薄膜的可见光催化能力。当V靶功率为150 W时,Ti_1-xV_xO₂薄膜的能带间隙值为 2.82 eV,其在2 h的可见光照射下分解了80%的RhB染料。这被归结于能带间隙窄,高能晶面{211}和结晶度高的共同作用。     

室温下制备以{211}晶面为主的Ti1-xVxO2薄膜及其可见光催化性能

以金属Ti和V作为靶材,采用直流反应共溅射技术在室温下制备了以{211}晶面为主的锐钛矿相Ti_1-xV_xO₂薄膜,研究了不同V靶功率对Ti_1-xV_xO₂薄膜的薄膜成分、晶相结构和可见光催化性能的影响。研究表明,Ti_1-xV_xO₂薄膜的晶相结构为锐钛矿相,择优取向为(211),而结晶度受V靶功率的影响。随着V靶功率的增加,薄膜中V元素含量逐渐增加,同时,晶粒和沉积速率也逐渐增加。另外,当V靶功率为150W时,薄膜的表面粗糙度值有一个最大值。V的掺杂导致薄膜的能带间隙变窄,对光的吸收向可见光区偏移,从而有效地改善了薄膜的可见光催化能力。当V靶功率为150W时,Ti_1-xV_xO₂薄膜的能带间隙值为2.82eV,其在2h的可见光照射下分解了80%的RhB染料。这被归结于能带间隙窄,高能晶面{211}和结晶度高的共同作用。     

Cathodic electrophoretic deposition of manganese dioxide films

Cathodic electrophoretic deposition (EPD) method has been developed for the deposition of manganese dioxide films. It was shown that phosphate ester (PE) is an effective charging additive, which provides stabilization of manganese dioxide nanoparticles in suspensions. The influence of PE concentration and deposition voltage on the deposition efficiency has been studied. EPD has been utilized for the fabrication of porous nanostructured films with thickness in the range of 0.5–20 μm for application in electrochemical supercapacitors (ES). Cyclic voltammetry and chronopotentiometry data for the films tested in the 0.1 M Na₂SO₄ solutions showed capacitive behavior in the voltage window of 1 V. The highest specific capacitance (SC) of 377 F g⁻¹ was obtained at a scan rate of 2 mV s⁻¹. The SC decreased with increasing film thickness and increasing scan rate in the range of 2–100 mV s⁻¹. The deposition mechanism, kinetics of deposition and charge storage properties of the films are discussed.     

Development of dye-sensitized solar cells based on visible-light-responsive TiO2 thin films with a unique columnar structure

A visible-light-responsive TiO₂ thin film (Vis-TiO₂), possessing a unique columnar structure oriented perpendicular to the substrate, has been prepared by using a radio-frequency magnetron sputtering deposition method. The unique TiO₂ thin film was used as a key component of N719 dye-sensitized solar cells (DSSCs). The rough morphology caused by the columnar structure leads to enhanced photovoltaic performances of these DSSCs as a consequence of increased amounts of adsorbed dyes and facilitated diffusion of the electrolyte into Vis-TiO₂ film. Additionally, photovoltaic performances of the DSSCs were found to depend strongly on the thickness of the Vis-TiO₂ film, which can be readily controlled by adjusting the sputtering time conducted for deposition. Consequently, a solar-to-electric energy conversion efficiency of 2.6 % under AM 1.5 illumination was observed for an optimally performing DSSC that has a Vis-TiO₂ film thickness of 6.9 μm, prepared by employing a sputtering time of 700 min.     

Enhancement of the efficiency of dye-sensitized solar cell with multi-wall carbon nanotubes/polythiophene composite counter electrodes prepared by electrodeposition

For the purpose of increasing the energy conversion efficiency of dye-sensitized solar cells (DSSCs), multi-wall carbon nanotube (MWCNT)/polythiophene (PTh) composite film counter electrode has been fabricated by electrophoresis and cyclic voltammetry (CV) in sequence. The morphology and chemical structure have been characterized by transmission electron microscopy (TEM), scanning electron microscope (SEM), and Raman spectroscopy respectively. The overall energy conversion efficiency of the DSSC employing the MWCNT/PTh composite film has reached 4.72%, which is close to that of the DSSC with a platinum (Pt) counter electrode (5.68%). Compared with a standard DSSC with MWCNT counter electrode whose efficiency is 2.68%, the energy conversion efficiency has been increased by 76.12% for the DSSC with MWCNT/PTh counter electrode. These results indicate that the composite film with high conductivity, high active surface area, and good catalytic properties for I₃⁻ reduction can potentially be used as the counter electrode in a high-performance DSSC.     

金属-有机框架薄膜衍生的CoSe2/N共掺杂碳膜作DSSC对电极

针对粉体MOF衍生材料存在制备工艺复杂、薄膜厚度难以控制等问题,我们通过液相外延分步生长法制备了一种金属有机框架薄膜(PIZA-1),然后以其作牺牲模板,在惰性氛围中制备了一种CoSe_2和N共掺杂的碳膜(CoSe_2/N-CF),并用作DSSC对电极,其具有制备简单、粘结力强、厚度可调等优势。系统表征了CoSe_2/N-CF形貌特点、结构性质及电化学性能,并深入研究了不同厚度薄膜、CoSe_2颗粒大小对DSSC的光伏性能的影响。结果表明,CoSe_2/N-CF-15电极具有优异的催化活性,所组装的DSSC获得了8.68%的光电转化效率(PCE),高于相同条件下Pt电极组装电池的PCE(7.97%)。     

TiO2纳米片/巢状分级结构纳米阵列薄膜的制备及其在染料敏化太阳能电池中的应用

采用水热合成法在氟掺杂二氧化锡(FTO)导电玻璃基底上得到TiO2纳米阵列薄膜,并进一步通过NaOH溶液水热处理制备了由巢状纳米阵列及纳米片覆盖层构成的TiO2纳米阵列分级结构一体化薄膜.采用场发射扫描电镜(FE-SEM),X射线衍射(XRD),紫外-可见(UV-Vis)漫反射光谱和吸收光谱技术对TiO2薄膜的结构和性质进行表征.FE-SEM结果表明:分级结构TiO2薄膜膜厚为1.5μm,薄膜由一层纳米片覆盖层(约0.2μm高)和一层巢状纳米阵列层(约1.3μm高)组成.XRD谱图表明TiO2薄膜为锐钛矿相.UV-Vis光谱显示分级结构TiO2薄膜具有较强的光捕获能力和染料吸附能力.TiO2纳米片/巢状分级结构纳米阵列薄膜作为光阳极,可有效地提高染料敏化太阳能电池的光电转换效率,其短路电流(Jsc)为7.79mA·cm-2,开路电压(Voc)为0.80V,填充因子(FF)为0.40,光电转换效率(η)为2.48%,其光电转换效率较TiO2纳米阵列薄膜提高了近10倍.     

Anode-supported solid oxide fuel cell with electrophoretic deposition-derived electrolyte operated under single-chamber conditions and a methane–air mixture

In this study, samaria-doped ceria (Sm_0.2Ce_0.8O_1.9, SDC) thin film is deposited on the Ni-SDC support by employing the electrophoretic deposition technique. Various factors are considered for the deposition of SDC films. The corresponding microstructure of the deposited SDC film is examined and correlated to the electrochemical performance as a single-chamber solid oxide fuel cell (sc-SOFC). It is found that the microstructure of the SDC film mainly relates to the particle size of SDC. After heat treatment, highly dense SDC film is obtained with the deposition condition of 5 g L⁻¹ of the SDC suspension (average grain size of SDC, 248 nm), 60 V as the applied potential, and the deposition time of 1 min (18 μm in thickness). For the Ni-SDC/SDC/SSC cell, an open circuit potential of 0.92 V and peak power density of 155 mW cm⁻² can be obtained at the furnace temperature of 500 °C.     

The fabrication of TiO<Subscript>2</Subscript> nanoparticle/ZnO nanowire arrays bi-filmed photoanode and their effect on dye-sensitized solar cells

Porous TiO₂ nanoparticles coated on ZnO nanowire arrays (TiO₂ NP/ZnO NW) as photoanode for dye-sensitized solar cell (DSSC) has been fabricated and investigated to improve the power conversion efficiency. The TiO₂ NP/ZnO NW photoanode consists of single crystalline ZnO NWs synthesized via hydrothermal method and porous TiO₂ NP film covered on the surface of ZnO NW arrays by screen printing technique. The effect of TiO₂ NPs thickness of the bi-filmed photoanode on the cell performance has been investigated, and TiO₂ NP/ZnO NW DSSC with NP thickness of ~5 μm exhibits the best efficiency of 4.68%, higher than 1.16% of ZnO NW DSSC and 3.18% of TiO₂ NPs DSSC, prepared and tested under identical conditions. The efficiency increase is attributed to the enlarged photocurrent, due to the greatly enhanced surface area for dye absorption and light harvesting efficiency resulted from TiO₂ NPs, and improved open-circuit voltage, due to reduced electron recombination by providing direct conduction pathway along ZnO NWs.     

Optimization of the electrophoretic deposition of YBa2Cu3O7−x superconducting large area coatings

Large area coatings (>10cm²) of the high temperature superconductor YBa₂Cu₃O_7–x (x = 0.1 – 0.2) (YBCO) have been prepared by scale up an electrophoretic deposition technique using silver sheets and Si-wafers coated with Ag or Au as substrates. Several parameters, like the kind of the solvent, the applied voltage, the distance between the electrodes, the initial concentration of the suspension and the temperature during the electrophoresis were investigated in order to attain high deposition rates, as well as uniform YBCO coatings with the proper stoichiometry. To obtain a strongly adherent and dense coating a subsequent appropriate sintering and annealing procedure has been developed. The coatings obtained were characterized for their stoichiometry and superconducting properties by X-ray diffraction (XRD), Raman spectroscopy and magnetic measurements. The homogeneity and thickness of the films and the average grain size of the deposited particles have been investigated by optical and scanning electron microscopy (SEM).     

Effects of Nanocrystalline Porous TiO2 Films on Interface Adsorption of Phthalocyanines and Polymer Electrolytes in Dye-Sensitized Solar Cells

Summary: We have synthesized three kinds of titanylphthalocyanines with different crystal structures (TiOPcs; PcT2000R, PcT3000R, and PcT1100S) and analyzed their crystal structure by X-ray Diffraction (XRD), Fourier transfer IR (FT-IR) spectroscopy, and Transmission Electron Microscope (TEM). From experimental results, we have confirmed that PcT2000R was estimated to be alpha-form; PcT3000R was beta-form, and PcT1100S was gamma-form. Quasi-solid state dye-sensitized solar cell (DSSC) devices were prepared with a polymer electrolyte using TiOPcs as a co-adsorbent. The DSSC device using TiOPc has higher power conversion efficiency than without TiOPc, due to decrease of electron transfer distance by the interface adsorption between TiO₂ film and polymer electrolyte. Also, we have studied the effects of the crystal structures of TiOPcs on the property of polymer electrolyte and the performance of the DSSC device. The best result on power conversion efficiency was 7.13% in DSSC device using PcT3000R having its highest stability. The open-circuit voltage (V_oc) was 0.69 V, the short-circuit current density (J_sc) was 20.02 mA/cm², and the Fill Factor (FF) was 0.52. the addition of TiOPc as co-adsorbent is useful for improve to the performances of DSSC devices such as V_oc, J_sc, and power conversion efficiency.