表面活性剂对染料敏化太阳能电池光电性能的提高

在硝酸/醋酸(HNO₃/HAc)的水溶液中分别加入十二烷基苯磺酸钠(DBS)、十六烷基三甲基溴化铵(CTAB)、吐温20等不同类型的表面活性剂来水解钛酸四正丁酯制得前驱体溶液,通过水热法制备纳晶TiO₂,并组装成染料敏化太阳能电池(DSSC)。通过XRD、SEM和UV-Vis对纳晶TiO₂薄膜进行表征,并对DSSC进行光电流-光电压(I-V)曲线的测试,研究了不同类型的表面活性剂和不同浓度的CTAB对DSSC光电性能的影响。结果表明：加入阳离子表面活性剂CTAB时提高了DSSC的光电性能,而加入阴离子表面活性剂DBS和非离子表面活性剂吐温20时,DSSC的光电性能反而降低。随着CTAB浓度的增加,电池的光电性能先提高后下降,当c_CTAB=0.08 mol·L^-1时,DSSC的光电转化效率最高为5.76%,比不添加表面活性剂制备的纳晶TiO₂所组装的DSSC的光电转化效率提高了约18%。     

电泳沉积法制备介孔TiO2/单壁碳纳米管薄膜

采用电泳沉积法, 在FTO/介孔TiO2薄膜上制备了介孔TiO2/单壁碳纳米管(SWCNTs)薄膜电极, 用Raman和SEM等手段对薄膜电极进行了表征. 结果表明, SWCNTs已沉积到介孔TiO2薄膜上. 分别用四羧基苯基卟啉(TCPP)和联吡啶钌化合物N719对其进行敏化, 并组装成太阳能电池. 研究结果表明, 与单纯的TiO2粒子膜相比, 介孔TiO2和SWCNTs的紧密结合可使得光生电子更容易传输, 光电转换效率显著提高.     

介孔碳-碳纳米管-硫化铜复合材料对电极的制备及其在量子点敏化太阳能电池中的应用

首先研究了介孔碳(MC)、碳纳米管(CNT)和不同MC/CNT质量比(m_(MC)/m_(CNT))制备的MC-CNT二元复合材料对电极的光电转换效率(PCE),进一步加入预先水热合成的CuS纳米材料,制备出MC-CNT-CuS三元复合材料对电极,同时探讨了CuS添加量和膜厚对对电极PCE的影响。实验结果表明,当m_(MC)/m_(CNT)=3/2时,2种碳材料能最大程度地发挥协同作用,使电池性能最好,PCE达12.69%。再加入0.4 g CuS时PCE可进一步提高,且对电极印刷5层时最优,此时所组装的电池获得的PCE最高(13.18%)。     

骨架结构多孔TiO2薄膜增强染料敏化太阳能电池性能

以空心球状TiO₂为基体、以片状TiO₂为骨架,采用刮刀法制备了染料敏化太阳能电池的多孔TiO₂光阳极薄膜。光电转化效率测试结果表明,当作为骨架支撑材料的片状TiO₂含量为20wt%时,光阳极薄膜组装成太阳能电池的光电转化效率达到最高值4.53%,比商业P25制备的无孔无骨架TiO₂薄膜电池(4.06%)及无骨架结构的多孔TiO₂薄膜电池(4.17%)的性能均有显著提高。当片状TiO₂的最佳含量为20wt%电池薄膜厚度为33 μm时,太阳能电池光电转化效率进一步提升为7.06%。光电性能增强的原因是骨架结构有利于快速传输电子并增大染料吸附量。本研究通过设计制备具有骨架结构的多孔TiO₂薄膜为提高染料敏化太阳能电池性能提供了新的思路。     

骨架结构多孔TiO2薄膜增强染料敏化太阳能电池性能

以空心球状TiO₂为基体、以片状TiO₂为骨架,采用刮刀法制备了染料敏化太阳能电池的多孔TiO₂光阳极薄膜。光电转化效率测试结果表明,当作为骨架支撑材料的片状TiO₂含量为20wt%时,光阳极薄膜组装成太阳能电池的光电转化效率达到最高值4.53%,比商业P₂₅制备的无孔无骨架TiO₂薄膜电池(4.06%)及无骨架结构的多孔TiO₂薄膜电池(4.17%)的性能均有显著提高。当片状TiO₂的最佳含量为20wt%电池薄膜厚度为33μm时,太阳能电池光电转化效率进一步提升为7.06%。光电性能增强的原因是骨架结构有利于快速传输电子并增大染料吸附量。本研究通过设计制备具有骨架结构的多孔TiO₂薄膜为提高染料敏化太阳能电池性能提供了新的思路。     

简易合成Cu2SnSe3作染料敏化太阳能电池对电极

采用简易溶剂热法合成直径为150-250 nm的Cu2SnSe3纳米颗粒.以Cu2SnSe3"墨水"为前驱体采用滴落涂布法在掺氟二氧化锡基板上沉积Cu2SnSe3薄膜作为染料敏化太阳能电池(DSSC)对电极.利用场发射扫描电镜(FESEM)、透射电镜(TEM)、X射线衍射(XRD)、拉曼光谱(Raman)、能谱仪(EDS)等对Cu2SnSe3纳米颗粒的形貌、结构和组成进行表征.结果表明:产物纯净无杂项且符合化学计量比.以Cu2SnSe3为对电极的DSSC转化效率为7.75%,与铂对电极DSSC效率相当(7.21%).研究表明,DSSC的光电流密度和影响因子与Cu2SnSe3薄膜厚度密切相关,这是由于不同厚度的Cu2SnSe3薄膜作对电极所对应的催化位置数目和电阻值不同.电化学阻抗谱研究说明,Cu2SnSe3因具有类似铂良好的电催化性能而适合用作染料敏化太阳能电池对电极材料.本文以Cu2SnSe3代替贵金属铂,提供了一种廉价制备高效染料敏化太阳能电池对电极的新方法.     

ZnO纳米管有序阵列与Cu2O纳米晶核壳结构的光电化学性能及全固态纳米结构太阳电池研究简

采用电化学方法在铟锡氧化物(ITO)导电玻璃基底上制备了高度有序的ZnO纳米管阵列,然后在ZnO纳米管阵列上电化学沉积Cu2O纳米晶颗粒,获得了一维有序Cu2O/ZnO核壳式纳米阵列结构,通过控制Cu2O纳米晶的沉积电量得到不同厚度的Cu2O壳层,并对该核壳式纳米阵列的形貌和结构进行了分析. 以Cu2O/ZnO一维核壳式纳米阵列结构为光电极组装全固态纳米结构太阳电池,研究了Cu2O壳层厚度对光电极光吸收性能、光电性能以及组装电池光伏性能的影响,优化了电池中对电极材料的喷金厚度. 结果表明,以Cu2O沉积电量为1.5 C的Cu2O/ZnO为光活性层,以4 mA电流下真空镀金20~25 min的铜基底为对电极组装的简易太阳电池最高可获得0.013%的光电转换效率.     

MnWO4/生物质衍生碳纳米复合催化剂的制备及催化性能

通过共沉淀法合成了双金属氧化物MnWO₄镶嵌生物质衍生碳（MnWO₄/BC）纳米复合催化剂,并将其作为对电极（counter electrode,CE）催化剂组装了染料敏化太阳能电池（dye-sensitized solar cell,DSSC）,探究了MnWO₄/BC在非碘体系中的催化性能和光伏性能。结果表明：在铜氧化还原（Cu²⁺/Cu⁺）电对DSSC中获得的光电能量转换效率（power conversion efficiency,PCE）为3.57%（D35）和1.59%（Y123）,高于Pt电极的PCE（3.12%,1.16%）;50次连续循环伏安测试表明,MnWO₄/BC催化剂具有较好的电化学稳定性。     

Self-Assembled Graphene/MWCNT Bilayers as Platinum-Free Counter Electrode in Dye-Sensitized Solar Cells

We describe the preparation and properties of bilayers of graphene- and multi-walled carbon nanotubes (MWCNTs) as an alternative to conventionally used platinum-based counter electrode for dye-sensitized solar cells (DSSC). The counter electrodes were prepared by a simple and easy-to-implement double self-assembly process. The preparation allows for controlling the surface roughness of electrode in a layer-by-layer deposition. Annealing under N₂ atmosphere improves the electrode's conductivity and the catalytic activity of graphene and MWCNTs to reduce the I₃⁻ species within the electrolyte of the DSSC. The performance of different counter-electrodes is compared for ZnO photoanode-based DSSCs. Bilayer electrodes show higher power conversion efficiencies than monolayer graphene electrodes or monolayer MWCNTs electrodes. The bilayer graphene (bottom)/MWCNTs (top) counter electrode-based DSSC exhibits a maximum power conversion efficiency of 4.1 % exceeding the efficiency of a reference DSSC with a thin film platinum counter electrode (efficiency of 3.4 %). In addition, the double self-assembled counter electrodes are mechanically stable, which enables their recycling for DSSCs fabrication without significant loss of the solar cell performance.     

The fabrication of TiO<Subscript>2</Subscript> nanoparticle/ZnO nanowire arrays bi-filmed photoanode and their effect on dye-sensitized solar cells

Porous TiO₂ nanoparticles coated on ZnO nanowire arrays (TiO₂ NP/ZnO NW) as photoanode for dye-sensitized solar cell (DSSC) has been fabricated and investigated to improve the power conversion efficiency. The TiO₂ NP/ZnO NW photoanode consists of single crystalline ZnO NWs synthesized via hydrothermal method and porous TiO₂ NP film covered on the surface of ZnO NW arrays by screen printing technique. The effect of TiO₂ NPs thickness of the bi-filmed photoanode on the cell performance has been investigated, and TiO₂ NP/ZnO NW DSSC with NP thickness of ~5 μm exhibits the best efficiency of 4.68%, higher than 1.16% of ZnO NW DSSC and 3.18% of TiO₂ NPs DSSC, prepared and tested under identical conditions. The efficiency increase is attributed to the enlarged photocurrent, due to the greatly enhanced surface area for dye absorption and light harvesting efficiency resulted from TiO₂ NPs, and improved open-circuit voltage, due to reduced electron recombination by providing direct conduction pathway along ZnO NWs.     

Preparation and properties of SiO2-TiO2 thin films from silicic acid and titanium tetrachloride

The preparation of SiO₂-TiO₂ thin films by the sol-gel method using silicic acid and titanium tetrachloride as starting materials was studied. The homogeneous sols were obtained by the condensation reaction of silicic acid with titanium tetrachloride in methanol-tetrahydrofuran. The dipcoating of slide glasses and silicon wafers followed by heat treatment gave oxide thin films of 88–93% transmittance, 3000–4500 Å thickness, and 1.45–1.80 refractive index, depending on heat-treatment temperature and TiO₂ content. FT-IR measurement showed that the Si-O-Ti bond is formed even in the sol and films. The variations of film thickness and refractive index on transformation from the gels into the oxides were found to be quite low.     

基于TiO2纳米管阵列的高效正面透光型染料敏化太阳能电池的制备及其光电性能

报道了一种基于TiO2纳米管(TNT)阵列正面透光型光阳极的高效染料敏化太阳能电池.将TNTs在450°C烧结后能避免其有序结构在HF处理过程中被破坏,使膜内高速电子传输通道被保留,有利于染料敏化太阳能电池(DSSC)实现高速电荷传输.再用HF、TiCl4、HF和TiCl4混合等溶剂对TNTs进行处理,提高其表面粗糙度以吸附更多染料.染料吸附量的增加能提高光阳极在300-570 nm波段光子捕获效率,该波段是染料吸收光子的主要区域.然而,在染料吸收光子较弱的长波段区域(570-800 nm)光子捕获效率的增加主要源于光阳极光散射率的提高.光阳极光子捕获效率的提高使DSSC的内外量子效率在全波段(300-800 nm)均有所增加,从而使短路电流明显提高.从电化学阻抗数据可知,与电子传输性能密切相关的电化学参数如电荷传输电阻、界面电荷复合电阻、电容、电子寿命、电子扩散长度和电子收集效率等在含处理过的TNTs光阳极DSSC中均有所改善,从而提高电池光电转换效率.含HF和TiCl4混合溶剂处理TNTs光阳极的DSSC最高光电转换效率能达到7.30%,比未处理的DSSC(5.38%)提高35.69%.     

Engineering the Electrical Conductivity of Lamellar Silver‐Doped Cobalt(II) Selenide Nanobelts for Enhanced Oxygen Evolution

Precisely engineering the electrical conductivity represents a promising strategy to design efficient catalysts towards oxygen evolution reaction (OER). Here, we demonstrate a versatile partial cation exchange method to fabricate lamellar Ag‐CoSe₂ nanobelts with controllable conductivity. The electrical conductivity of the materials was significantly enhanced by the addition of Ag⁺ cations of less than 1.0 %. Moreover, such a trace amount of Ag induced a negligible loss of active sites which was compensated through the effective generation of active sites as shown by the excellent conductivity. Both the enhanced conductivity and the retained active sites contributed to the remarkable electrocatalytic performance of the Ag‐CoSe₂ nanobelts. Relative to the CoSe₂ nanobelts, the as‐prepared Ag‐CoSe₂ nanobelts exhibited a higher current density and a lower Tafel slope towards OER. This strategy represents a rational design of efficient electrocatalysts through finely tuning their electrical conductivities.     

Structure and properties of (1−x)(0.6Pb(Zn1/3Nb2/3)O3-0.4Pb (Mg1/3Nb2/3)O3)-xPbTiO3 thin films with perovskite phase promoted by polyethylene glycol

The preferential formation of a pyrochlore structure is a knotty problem in the preparation of Pb(Zn_1/3Nb_2/3)O₃ (PZN)-based thin film materials and its presence is significantly detrimental to the dielectric and piezoelectric properties. In this study, 40 mol% of PZN was replaced with Pb(Mg_1/3Nb_2/3)O₃ (PMN) for obtaining a perovskite composition around a morphotropic phase boundary (MPB), (1−x)(0.6PZN-0.4PMN)-xPT ((1−x)PZMN-xPT, PT: PbTiO₃) where x = 0.23. The thin films with this composition were prepared with a polyethylene glycol (PEG) modi-fied sol-gel method on LaAlO₃ substrates. The microstructural evolution of the films on heat treatment was examined with X-ray diffraction. With the aid of PEG, the formation of the pyrochlore phase was suppressed and the perovskite phase formed directly from the amorphous gel film. The multilayer films with a thickness around 0.25 μm showed a single perovskite phase without any detectable pyrochlore structure. Microscopic images showed uniform grain size of a few tens of nanometers. The role of the polymer dramatically promoting the perovskite phase was investigated with the aid of X-ray photoelectron spectroscopy and thermal analysis. The dielectric constant of the obtained film was 4160 at 1 kHz. The film demonstrated typical ferroelectric hysteresis loops and exhibited excellent piezoelectric performance.     

纯相Li2MnO3薄膜的制备及作为锂离子电池正极材料的电化学行为

采用固相烧结法制备了纯相Li₂MnO₃正极材料及靶材,采用脉冲激光沉积（PLD）法在氧气气氛、不同温度下沉积了Li₂MnO₃薄膜. 通过X射线衍射（XRD）和拉曼（Raman）光谱表征了薄膜的晶体结构,采用扫描电镜（SEM）观察薄膜形貌及厚度,利用电化学手段测试了Li₂MnO₃薄膜作为锂离子电池正极材料性能. 结果表明,PLD 方法制备的纯相Li₂MnO₃薄膜随着沉积温度升高薄膜结晶性变好. 25 ℃沉积的薄膜难以可逆充放电,400 ℃沉积的薄膜具有较高的电化学活性和循环稳定性. 相对于粉末材料,400与600 ℃制备的Li₂MnO₃薄膜电极平均放电电位随着循环次数的衰减速率明显低于相应的粉体材料.     

Controllable preparation of nanosized TiO<Subscript>2</Subscript> thin film and relationship between structure of film and its photocatalytic activity

TiO₂ nano-crystalline film and fixed bed photocatalytic reactor were prepared by the sol-gel process using tetrabutylorthotitanate as a precursor and glass tube as the substrate. XRD, AFM, SEM and thickness analysis results indicate that the preparation of nano-crystalline film can be controlled by optimizing experiment process. Under the optimized process, the phase of TiO₂ in film is anatase, and the grain size is 3–4 nm. The size of particles, which is about 20-80 nm, can be controlled. The thickness of monolayer film is in nanometer grade. The thickness and particles size in films growing on nanometer film can also be controlled in nanometer grade. As a result, the crack of film can be effectively avoided. Rhodamine degradation results using UV-Vis spectrophotometer show that the activity of nano-crystalline film in the photocatalytic reactor has a good relation with the diameter of TiO₂ particles, that is, the film shows high activity when the size is 20 –30 nm and greatly reduced when the size is above 60 nm. The activity of film does not decrease with the increase of film thickness, and this result indicates that nano-crystalline film has no ill influence on the transmissivity of ultraviolet light.     

Preparation of TiO2 nanocrystalline films controlled by acetylacetone/polyethylene glycol and their photoelectric properties

TiO₂ nanocrystalline films were prepared from titanium tetra-n-butoxide modified with double hydrolysis inhibitors, acetylacetone and polyethylene glycol (PEG), in mixture of methanol and ethanol. The correlation among surface structure of the TiO₂ films, preparation conditions, and photovoltaic properties of the solar cells using the TiO₂ films was investigated. The particle size of the obtained TiO₂ films was decreased as the PEG content increased. The nanostructured films with the narrow distribution of particle size could be prepared. The amounts of adsorbed dyes for these TiO₂ films were larger than that without PEG. The performance of the solar cell fabricated using the TiO₂ film improved as the amount of the PEG increased, and the solar cell using the TiO₂ film prepared from the solution with 30 wt% PEG exhibited the highest performance.