焙烧温度对Nb2O5/α-Al2O3催化剂结构及催化性能的影响

 制备了Nb2O5/α-Al2O3催化剂并用于环氧乙烷水合反应制乙二醇,采用X射线衍射,热重-差热分析,红外光谱,吸附氨的程序升温脱附,吸附环氧乙烷的程序升温脱附,扫描电镜和透射电镜研究了焙烧温度对催化剂物理化学性质及催化性能的影响. 结果表明,焙烧温度明显影响氧化铌催化剂的结构、酸量及酸强度. 催化剂的结构不同,环氧乙烷在催化剂表面的吸附强度存在明显差别,而催化剂的酸量和酸强度影响其催化性能.     

具有不同层间距、比表面和孔径大小的氧化硅柱层状铌酸的制备

层柱金属氧化物是近年来被开发的新型无机多孔材料［１～６］．水合铌酸是一类独特的固体酸催化剂,通常是非孔性的,且经较高温度热处理后比表面和酸性均很小,从而限制了其在催化领域中的应用［７］．我们［３］曾报道了氧化硅柱层状铌酸的制备,本文则通过进一步改变制备过程中所用氨基丙基三乙氧基硅烷（ＡＰＳ）溶液的浓度、反应温度和时间,获得了一系列具有不同层间距、比表面和孔径的氧化硅柱层状铌酸．１　实验部分ＨＮｂ３Ｏ８·Ｈ２Ｏ的制备见文献［８］．将１ｇＨＮｂ３Ｏ８·Ｈ２Ｏ加入７０ｍＬ不同浓度的ＡＰＳ水溶液中,所得…     

稻壳碳基固体酸催化剂的制备及在木糖脱水制备糠醛反应中的催化性能

以工业生产中碱法溶硅剩余的稻壳残渣为碳源,采用硫酸磺化法制备稻壳碳基固体酸催化剂,考察了其催化木糖脱水制备糠醛的性能.采用红外光谱、元素分析及表面酸浓度测定等手段对催化剂进行了表征.对固体酸催化剂的制备条件进行了优化,所得催化剂的表面酸浓度可达1.03 mmol/g.以木糖脱水制备糠醛为模型反应,考察了溶剂类别、反应温度和反应时间对固体酸催化剂催化性能的影响.实验结果表明,以二甲基亚砜(DMSO)为反应溶剂效果优于水,并且随着反应温度的升高和反应时间的延长,反应产率逐渐增加,最高可达75.8%.此外,还对催化剂的循环性能进行了研究,探讨了其失活原因和再生方法.     

烷基化催化剂表面酸性及催化性能的动力学研究

在确定关联升温速率、脱附峰温和脱附峰覆盖率的程序升温脱附动力学模型的基础上，通过TPD实验和模型参数估值，建立了表征催化剂酸密度、酸强度及强度分布情况的方法。研究表明，随着活化温度的提高，固体酸催化剂表面酸中心强度分布先变宽后趋于均匀，350?℃活化催化剂的强度分布最宽；催化剂表面酸强度和酸密度随活化温度提高均呈先增大后降低、分别在350 ℃和250 ℃活化温度达到极大值的变化规律。催化剂酸性与催化性能关联的结果表明，随着活化温度的提高，烷基化反应速率常数与总脱附量的变化趋势相同，而催化剂失活速率常数与脱附活化能变化趋势相同；催化剂活性稳定性随其酸强度的增大而变差，催化剂活性与催化剂酸量和酸强度有关。     

固体铌酸催化下甲苯的硝化

在不同焙烧温度下制备了一系列固体铌酸催化剂。测定了固体铌酸催化剂的比表面积、表面酸强度及表面酸量。研究了催化剂焙烧温度、硝化反应时间、硝化反应温度、有无醋酐存在、硝酸浓度、催化剂的重复使用等因素对甲苯硝化反应影响。实验结果表明,当反应温度为40℃,反应时间为60 min时,以CCl4为溶剂,以质量分数为95%的硝酸为硝化剂,在醋酐存在条件下,以经300℃焙烧3 h后的铌酸作为催化剂,甲苯硝化产物中异构体的邻对比达1.26,较硝硫混酸的1.67显著降低,产物得率达99.3%。且该催化剂循环使用5次,催化活性基本不变,是一种极具应用前景的绿色硝化反应催化剂。     

脱铝丝光沸石表面酸性及其对α—蒎烯烷氧基化反应的催化作用

以盐酸水热处理方法制备了一系列脱铝丝光沸石催化剂,测定了其表面酸度和酸强度分布：考察了α－蒎烯与脂肪醇的烷氧基化反应中催化表面酸性、脂肪醇分子性质的影响规律;确定了催化剂的适宜酸强度范围,探讨了催化剂内、外表面酸中心对反应活性的贡献。     

新型磁性纳米固体酸催化剂ZrO2/Fe3O4的制备及表征

根据将磁性一材料和固体酸进行组装的设想，成功制备了磁性纳米固体酸催化剂。纳米级样性前体-磁基体(Fe3O4)的磁性、粒子尺寸受到Fe^2^+/Fe^3^+投料比和用于沉淀的NaOH浓度的显著影响；不同复合方法也对磁性固体酸催化剂ZrO2/Fe3O4的酯化催化性能影响显著。XRD，XPS，TEM，比表面积测定，元素组成分析及磁学性能测定等表征结果证实，新型催化剂以磁性材料为核，固体酸催化剂活性组分包覆在其外部形成包覆型的磁性纳米催化剂。该系列催化剂均具有较小的粒子尺寸、较强的磁性及较高的酯化催化活性；并且易于通过磁场进行回收，使用寿命较长。它们对乙酸与正丁醇酯化反应的催化活性随着ZrO2含量增加而提高。催化剂中ZrO2的晶化温度因为Fe3O4的存在而升高，有利于催化剂活性的保持，热处理温度会对催化剂的磁性及催化活性产生影响。     

硼改性Hβ-沸石上FCC轻汽油的醚化反应性能

研究了β－沸石对FCC轻汽油醚化反应的催化性能，考察了硼改性对Hβ－沸石的催化性能及表面酸性的影响，并用NH3－TPD和IR表征了改性后Hβ－沸石的表面酸性。实验结果表明，适量硼改性改善了催化剂的性能，提高了醚化反应活性；调变了催化剂的表面酸性，使得催化剂上弱酸中心的强度有所增加，强酸中心的强度略有下降，总酸量增加，且以L酸为主，L酸中心有利行醚化反应。     

焙烧温度对镧改性HZSM-5表面性质及乙醇脱水制乙烯反应性能的影响

采用浸渍法将稀土金属La负载在HZSM-5分子筛上,考察了在450~600℃范围内焙烧温度对La改性HZSM-5(La/HZSM-5)表面性质及催化乙醇脱水制乙烯性能的影响。X射线衍射和N2吸附-脱附分析分别表明焙烧温度对La/HZSM-5的晶体结构和孔结构影响不大,而NH3程序升温脱附测试则表明随着焙烧温度的升高La/HZSM-5的表面酸量和酸强度均有明显下降的趋势,相应的催化性能测试表明催化剂的活性和寿命也随之下降,这可归结于不同焙烧温度下La物种形态差异的结果。以450℃下焙烧制备的3%La/HZSM-5为优选催化剂,在最佳的反应条件下,其单程使用寿命可达108天。     

硅胶负载磷钼杂多酸催化氧化糠醛制顺丁烯二酸酐

采用浸渍法制备负载型磷钼杂多酸催化剂,分析了催化剂的比表面积、分散性、结构特征、稳定性以及再生温度等性质.通过固定床微反应器考察杂多酸催化剂催化氧化糠醛生成顺丁烯二酸酐的催化性能.研究了焙烧温度、负载量对催化剂性能的影响,以及反应温度对顺丁烯二酸酐收率的影响.结果表明:通过浸渍制备的杂多酸催化剂具有杂多酸催化剂的Keggin结构,具有较好的稳定性和酸性;活性组分能较好的分布于载体SiO2上;催化剂的再生温度和活化温度均为400℃;在钼磷原子比为0.85,负载量为48.6%时催化性能较好,催化剂的表面酸量为0.646 mmol/g;反应温度控制在365℃附近时,顺丁烯二酸酐收率可达到57.2%,选择性为62.7%.     

电堆集富集非水毛细管电泳同时测定水杨酸、肉桂酸、阿魏酸和香草酸

建立了同时分离测定水杨酸、肉桂酸、阿魏酸和香草酸的电堆集富集-非水毛细管电泳(NACE)的新方法。运行缓冲溶液为40mmol/L乙酸钠-2.5mmol/L氢氧化钠甲醇溶液,电压-25kV,在225nm波长下紫外检测。对电压、乙酸钠浓度、氢氧化钠浓度、进样时间、样品溶液等因素对电堆集及分离的影响做了系统的研究。水杨酸、肉桂酸、阿魏酸和香草酸分别在1.4~28mg/L、0.40~8.0mg/L、0.7~18mg/L和0.7~30mg/L范围内线性关系良好(r=0.9999、r=0.9997、r=0.9994、r=0.9997);回收率分别为95.8~99.6%、96.2~98·2%、95.7~105%和98.9~103%,基于3倍信噪比(S/N=3),4种有机酸的检出限分别为0.069、0.051、0.107和0.089mg/L。     

离子色谱法测定乙醛酸中的顺丁烯二酸和乙二酸

采用抑制电导离子色谱法测定高浓度乙醛酸基体中痕量的顺丁烯二酸和乙二酸。将乙醛酸样品稀释至1 000倍体积后,采用高浓度的淋洗液,以高容量色谱柱对样品进行分析。实验结果表明,顺丁烯二酸和乙二酸最低检出限分别为12.7,19.6μg/L,重现性(n=5)分别为1.13%,1.11%,回收率分别为97.9%,94.7%。该方法具有较高的灵敏度,适用于乙醛酸的例行检测。     

Determination of Cyanuric Acid or Trichloroisocyanuric Acid in Air

Abstract

An analytical procedure for measurement of cyanuric acid or trichlor oisocyanuric acid in air has been developed. The procedure involves air sampling with a 37-mm PVC membrane filter, recovery with a phosphate buffer, and analysis by high performance liquid chromatography with a UV detector at 225 nm. The interior surface of the front piece of the cassette filter holder also is analyzed. Average recoveries were 0.98 to 1.00 after fortification of PVC filters with 12- to 412-μg quantities of cyanuric acid. Average recoveries of trichloroisocyanuric acid were 0.83 to 0.98 after fortification of glass surfaces with 12- to 424-μg quantities (these are reasonable approximations for recoveries of trichloroisocyanuric acid from PVC filters). The analyst should ascertain which analyte is present at the sampling site because trichloroisocyanuric acid reacts with water in the phosphate buffer to form cyanuric acid in high yield.     

对氨基苯甲酸的合成研究进展

综述了以对硝基苯甲酸为原料合成对氨基苯甲酸的近期研究进展。并从技术和经济角度讨论了各种合成方法的优点与不足。     

Surface Functionalization of Magnetite Nanoparticles with Sulfonic Acid and Heteropoly Acid: Efficient Magnetically Recoverable Solid Acid Catalysts

New magnetically recoverable solid acid catalysts for acid‐catalyzed reactions were designed via the surface chemical functionalization of silica‐coated magnetite nanoparticles (SCMNPs) with sulfonic acid groups. First, the SCMNPs were covalently functionalized with 3‐aminopropyl groups to achieve Amp‐SCMNPs. Then, reaction of the Amp‐SCMNPs with 1,4‐butane sultone followed by acidification with phosphotungstic acid (HPW) or diluted sulfuric acid produced magnetically recoverable solid acid catalysts, HPW‐ampsul‐SCMNPs and H‐ampsul‐SCMNPs, respectively. Both catalysts were characterized by various physicochemical analyses such as Fourier transform infrared (FT‐IR) and inductively coupled plasma‐optical emission (ICP‐OES) spectroscopies, vibrating sample magnetometry (VSM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), and energy‐dispersive X‐ray (EDX) analyses. Finally, the catalytic activities of the prepared catalysts were examined in the esterification of acetic acid with butanol and acetalization of benzaldehyde with ethylene glycol. Excellent catalytic efficiencies were obtained in both cases. The catalysts were consecutively recovered and reused five times without significant loss of their activities.     

以对甲基苯磺酸作为淋洗液用离子色谱法测定酸雨中的有机酸

本文研究了用对甲基苯磺酸作为淋洗液测定液相中HCOO~-和CH_3COO~-的离子色谱条件,该方法对HCOO~-和CH_3COO~-的最低检出限分别为48ppb和93ppb。该方法与用进口的辛磺酸作为淋洗液的方法进行了对比实验,并用于两广实际酸雨样品中甲酸和乙酸的测量。     

Mechanochemical Complexation between Deoxycholic Acid and Salicylic Acid

A complex between deoxycholic acid (DCA) and salicylic acid (SA) was prepared by grinding and coprecipitation methods. The resultant complex was characterized by means of powder X-ray diffractometry, IR spectroscopy and thermal analysis. The stoichiometry (DCA : SA 1 : 1) of the complex obtained by grinding was identical to that obtained by coprecipitation. The powder X-ray diffraction pattern of the DCA–SA complex differed from the typical pattern of DCA–guest complexes such as DCA–camphor and DCA–phenanthrene complexes. IR spectra suggested that a different kind of hydrogen bonding was formed in the crystal of the DCA–SA complex, compared with the other DCA–guest complexes. This was in good agreement with data from the crystal structure.     

硝酸氧解法提高泥炭中黄腐酸的产率

硝酸氧解法提高泥炭中黄腐酸的产率;腐植酸;硝酸氧化降解     

Determination of Monochloroacetic Acid and Dichloroacetic Acid for Quality Control of Acetic Acid Chlorination Industry by Ion Chromatography

An ion chromatographic method is described for the purpose of quality control in the process of monochloroacetic acid production. Using 2.5 mM NaOH–10% methanol as eluent, the simultaneous determination of acetic acid, monochloroacetic acid, dichloroacetic acid, and Cl⁻ was obtained in a single run. Monochloroacetic acid and dichloroacetic acid showed good linearity in the range 0.1–20 and 0.15–20 μg/ml and correlation coefficients were 0.9999 and 0.9998, respectively. The detection limits (signal-to-noise ratio 3:1) of monochloroacetic acid and dichloroacetic acid were 17 and 25 ng/ml. This simple, sensitive, and time-saving method can be applied for composition analysis in acetic acid chlorination production.