聚乙烯表面接枝聚合改性及抗凝血性的研究

聚乙烯(PE)膜经Ar等离子体预处理，无光引发剂紫外光照接枝甲基丙烯酸缩水甘油酯(GMA)，然后进行肝素化处理，以改善PE的抗凝血性能。用正交实验确定接枝反应的最优条件。通过X-射线光电子能谱(XPS)、衰减全反射红外光谱(ATR-FTIR)、扫描电子显微镜(SEM)和接触角测定PE膜接枝GMA前后表面性能和表面形貌。用复钙时间、凝血酶原时间、部分凝血活酶时间、凝血酶时间和血小板粘附实验对其抗凝血性能进行评价，结果表明，被修饰PE膜的抗凝血性能显著提高。     

一种新颖的抗血栓材料的研究

聚氨酯和肝素经低温等离子体表面处理后，直接以共价键形式结合，在聚氨酯管的内壁生成了光滑的聚氨酯－肝素接枝共聚体，经全血凝固时间的检测，新鲜人血注入聚氨酯－肝素接枝管后搁置５昼夜，电镜检查其管壁未见血栓痕迹，凝血酶时间等检测表明，接枝管起着抗血液凝固的功效，且肝素不脱落，经红外光谱测试，差谱中的新吸收谱带１１６５和１３３９ｃｍ＾－１表明聚氨酯和肝素分子之间生成了新共价健Ｎ－ＳＯ２或Ｏ－ＳＯ２的ＳＯ２     

等离子体引发HEMA的RAFT接枝聚合改性聚丙烯多孔膜

采用等离子体引发的可逆加成-断裂链转移(RAFT)接枝聚合法,以甲基丙烯酸羟乙酯(HEMA)为单体,对聚丙烯(PP)多孔膜表面作了亲水改性.研究了接枝聚合动力学,并以FT-IR、SEM、压汞、水通量等方法研究了改性膜的表面结构形态及孔结构.结果表明,等离子体引发的RAFT接枝聚合速率显著低于普通等离子体引发的接枝聚合速率.表面接枝率随着接枝聚合时间的延长呈线性增长趋势,同时改性膜的孔径和水通量随之减小.     

木材表面改性的XPS分析

利用微波等离子体对木材表面进行处理，并诱导引发接枝甲基丙烯酸甲酯；达到表面改性的效果以提高木质材料的性能，利用X射线光电子能谱(XPS)对木材表面改性前后的表面化学结构进行分析；结果表明：木材经微波等离子体处理，表面氧与碳的原子浓度比(no／nc)增加，产生大量的含氧官能团或过氧化物，从而引发木材与甲基丙烯甲酯单体产生接枝共聚反应。     

接枝丙烯酰胺改善聚乙烯膜表面亲水性的研究

利用等离子体技术和紫外照射接枝相结合在聚乙烯膜表面接枝丙烯酰胺(AAm)以改善其亲水性。通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)和接触角测定验证了在无光引发剂的条件下,将等离子体预处理和紫外照射接枝结合起来可以有效地提高AAm的接枝效果,很好地改善PE膜表面的亲水性。探讨了等离子体复合参数W/(FM)、等离子体预处理时间、AAm单体浓度以及紫外照射时间对改善PE膜表面亲水性的影响,确定改善PE膜表面亲水性的最佳实验条件。     

聚丙烯微孔膜表面的等离子体接枝

通过氢气氛等离子体处理，在聚丙烯微孔膜表面接枝了聚丙烯酸，改善了膜表面的亲水性。接枝率与等离子体放电功率、放电时间和溶液浓度有关，微孔膜内外表面及不同位置接枝效率有差别。接枝后微也膜的表面孔径减少了。     

溶剂对等离子体引发的衰减链转移接枝聚合动力学的影响

采用等离子体引发的衰减链转移(DT)接枝聚合法,以丙烯酸(AA)为单体,碘仿为链转移剂,对聚丙烯(PP)薄膜进行表面改性。研究了水和N,N-二甲基甲酰胺(DMF)对等离子体引发聚合及等离子体引发DT聚合动力学的影响。结果表明,采用等离子体引发的方法可以实现DT可控-活性聚合,DMF介质中的可控性优于水介质,等离子体引发DT聚合的溶剂效应明显减弱,接枝量与转化率成正比关系并与FT-IR、接触角的表征结果相符。     

利用等离子体技术研究聚苯乙烯表面的接枝聚合反应

用O₂等离子体对聚苯乙烯(PS)进行预处理, 再用Ar等离子体引发N-乙烯基吡咯烷酮(NVP)在其表面接枝聚合. 通过接触角(CA)及表面自由能(SE)分析, 探讨了O₂等离子体预处理条件对PS表面自由能的影响, 确定了预处理的最佳条件. 通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)和动态接触角(DCA)分析, 比较了O₂等离子体预处理前后和接枝聚合前后PS的表面组成及表面性能, 实验结果表明, 利用等离子体技术能成功地将NVP接枝聚合于PS表面, 接枝聚合后的PS表面由于极性高分子链和粗糙度的增加, 亲水性增强, 水滴易在其表面铺展. 由于接枝聚合后PS表面的高分子链在水中发生重构, 使后退角降低幅度较大, 接触角滞后现象明显.     

等离子体引发聚合及其应用

系统介绍了等离子体引发聚合的方法，特点，着重介绍等离子体引发聚合在超高分子量聚合物的合成，嵌段聚合，接枝聚合及无机高分子，单晶聚合物合成等方面的应用研究成果。     

等离子体辐照的聚乙烯表面接枝交联共聚合

聚合物利用低温等离子体预辐照进行表面接枝共聚合已有报道.此方法的优点是接枝层被限制在聚合物表面,辐照过程对基材本体性质无影响,且整个过程对环境无污染. 用等离子体使聚合物表面产生自由基,不需要表面具有不饱和键或特殊官能团,因而适用于任何聚合物,甚至于一些无机物如玻璃等.利用等离子辐照后暴露于空气的聚合物表面上生成的过氧自由基或过氧化物进行接枝反应,一般接枝量不大.本工作中,我们自己设计了反应器,以超高分子量聚乙烯(UHMWPE)为基材,以甲基丙烯酸甲酯(MMA)为接枝单体,在无氧条件下利用等离子体辐照产生的表面自由基进行了接枝聚合,产物接枝量高达10％.还用顺磁共振技术对表面自由基性质及其在接枝过程中的行为进行了跟踪研究.     

多单体接枝聚丙烯对PBT/PP共混体系的形态结构及力学性能影响研究

研究了甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)多单体熔融接枝聚丙烯 (PP g (GMA co St) )对聚对苯二甲酸丁二酯 (PBT) 聚丙烯 (PP)共混物的形态结构和力学性能的影响 .利用双螺杆挤出机对PBT PP合金进行共混挤出 ,使用DSC、FT IR和SEM、TEM等手段对共混物进行了分析和相形态观察 ,并测试了力学性能 .实验证明 ,熔融共混过程中PP g (GMA co St)的环氧基团可以与PBT的端羧基发生化学反应 ,就地生成了PBT g PP共聚物 ,该共聚物可对PBT PP合金起到良好的增容剂作用 ,使共混物的相区尺寸显著减小 ,共混物的拉伸强度和冲击强度等力学性能同时得到明显改善 ,达到了弹性体系或小分子增容所难以达到的力学性能平衡的效果 .此外 ,TEM的研究还在PBT PP g (GMA co St)共混物中发现了特殊的微相分离结构     

GMA/苯乙烯多组分单体接枝聚丙烯结晶行为研究

使用差示扫描量热计 (DSC)研究了甲基丙烯酸缩水甘油酯 苯乙烯 (GMA St)多单体熔融接枝聚丙烯[PP g (GMA co St) ]的等温和非等温结晶行为 ,用偏光显微镜观察了结晶的形态 ,并利用Avrami方程对其结晶动力学进行了分析 .研究发现接枝聚丙烯的结晶模式与PP相似 ,属于异相成核控制的球晶三维生长 ;但接枝聚丙烯的结晶温度 (Tc)显著提高 ,幅度高达 16～ 19℃ ,总结晶速率与纯PP相比明显加快 .接枝聚丙烯上GMA co St支链的存在 ,降低了成核界面自由能 ,促进了聚丙烯结晶的异相成核 .在接枝率不太高的情况下 ,随着接枝率的提高 ,接枝聚丙烯的结晶温度升高 ,总结晶速率加快 .在高接枝率范围内 ,随着接枝率的提高 ,接枝PP的Tc 不再升高 ,且由于接枝链的增长严重阻碍了球晶生长 ,导致接枝PP的总结晶速率反而随接枝率的升高而下降     

多组分单体接枝聚丙烯/尼龙6反应共混物结晶行为研究

用多组分熔融接枝的方法将甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)共同接枝到聚丙烯 (PP)上 ,制得具有较高GMA接枝率的多单体接枝聚丙烯 ,PP g (GMA co St) .将PP g (GMA co St)与尼龙 6 (PA6 )进行共混 ,利用扫描电镜 (SEM) ,差示扫描量热计 (DSC)和广角X射线衍射 (WAXD)对共混物的形态和结晶进行了研究 .在共混过程中 ,PP g (GMA co St)与PA6反应原位生成了PP g PA6 ,有效改善了共混物的相容性 ,分散相尺寸明显减小 .在PP g (GMA co St) PA6为 3 7的体系中 ,PP g (GMA co St)出现分级结晶现象 ,其在较低温度下的结晶属于均相成核结晶 .在PP g (GMA co St) PA6为 7 3的体系中 ,由于PA6相分散细微 ,在通常结晶温度下不结晶 ,而是在低温下均相成核与PP g (GMA co St)同时结晶 .WAXD证实体系中接枝PP ,PA6为分别结晶 ,无共晶或新的晶型产生     

Grafting of glycidyl methacrylate onto polypropylene using supercritical carbon dioxide

Free-radical grafting of glycidyl methacrylate (GMA) onto polypropylene (PP) films has been studied using supercritical carbon dioxide (SC-CO₂) as a solvent and a swelling agent. As the reaction temperature was below the melting point, PP was modified in the solid phase. The PP film was first soaked with the monomer GMA and benzoyl peroxide (BPO) as an initiator using SC-CO₂ at different experimental conditions of pressure, temperature, and thermal treatment time. After releasing CO₂, film GMA molecules were grafted onto PP in different times. Using this method, the degree of grafting and the morphology could be controlled through the combination of pressure, temperature, and soaking time. FTIR spectra confirmed that GMA had been grafted onto PP and that polypropylene-graft-glycidyl methacrylate (PP-g-GMA) presented a high surface reactivity for conductive polyaniline anchoring. DSC measurements and TG analyses showed that the thermal profiles of the graft copolymer and virgin PP are quite similar and that the graft PP does not exhibit changes in terms of thermal degradation profile and melting temperature, respectively. X-ray data showed that a high degree of grafting leads to a lower degree of crystallinity of polypropylene.     

Preparation of fully cross‐linked CNBR/PP‐g‐GMA and CNBR/PP/PP‐g‐GMA thermoplastic elastomers and their morphology,structure and properties

Binary CNBR/PP‐g‐GMA and ternary CNBR/PP/PP‐g‐GMA thermoplastic elastomers were prepared by reactive blending carboxy nitrile rubber (CNBR) powder with nanometer dimension and polypropylene functionalized with glycidyl methacrylate (PP‐g‐GMA). Morphology observation by using an atomic force microscope (AFM) and TEM revealed that the size of CNBR dispersed phase in CNBR/PP‐g‐GMA binary blends was much smaller than that of the corresponding CNBR/PP binary blends. Thermal behavior of CNBR/PP‐g‐GMA and CNBR/PP blends was studied by DSC. Comparing with the plain PP‐g‐GMA, T_c of PP‐g‐GMA in CNBR/PP‐g‐GMA blends increased about 10 °C. Both thermodynamic and kinetic effects would influence the crystallization behavior of PP‐g‐GMA in CNBR/PP‐g‐GMA blends. At a fixed content of CNBR, the apparent viscosity of the blending system increased with increasing the content of PP‐g‐GMA. FTIR spectrum verified that the improvement of miscibility of CNBR and PP‐g‐GMA was originated from the reaction between carboxy end groups of CNBR and epoxy groups of GMA grafted onto PP molecular chains. Comparing with CNBR/PP blends, the tensile strength, stress at 100% strain, and elongation at break of CNBR/PP‐g‐GMA blends were greatly improved. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1042–1052, 2004     

甲基丙烯酸缩水甘油酯/苯乙烯固相接枝聚丙烯

以苯乙烯(St)为共单体，过氧化苯甲酰(BPO)为引发剂，采用固相接枝反应将甲基丙烯酸缩水甘油酯(GMA)接枝到聚丙烯(PP)大分子链上。研究了反应时间、单体用量、引发剂用量等因素对接枝率的影响。采用凝胶渗透色谱(GPE)测定了PP和接枝物PP-g-(GMA-St)的分子量和分子量分布。结果 表明固相接枝PP反应条件为[GMA／[St]=2，反应3．5h，加入GMA 10份，BPO 5份。St的加入有助于GMA与PP的接枝，同时在一定程度上抑制了PP的降解。     

Plasma polymerization and deposition of glycidyl methacrylate on Si(100) surface for adhesion improvement with polyimide

Thin polymer films were deposited on Si(100) surfaces by plasma polymerization of glycidyl methacrylate (GMA) under different glow discharge conditions. The FT‐IR, X‐ray photoelectron spectroscopy (XPS), and amine treatment results suggested that the epoxide functional groups of the deposited films had been preserved to various extents, depending on the plasma deposition conditions. The use of a low radio frequency power (～ 5 W) and a relatively high system pressure (100–400 Pa) readily resulted in the deposition of thin films having nearly the same composition of the epoxide functional groups as that of the GMA homopolymer. The plasma‐polymerized GMA (PP‐GMA) thin films deposited on the Ar plasma‐pretreated Si(100) surfaces were retained to a large extent after acetone extraction, suggesting the presence of covalent bonding between the PP‐GMA layer and the Si surface. Thermal imidization of the poly(amic acid) precursor of polyimide on the GMA plasma‐polymerized Si(100) surface resulted in a strongly adhered polyimide film. The adhesion results further suggested that the GMA polymer had been grafted on the Si(100) surface and the epoxide functional groups had undergone reactive interaction (curing) with the carboxylic and amine groups of the poly(amic acid) during thermal imidization. Copyright © 2001 John Wiley & Sons, Ltd.     

Surface modification of polymers. V. Biomaterial applications

Polyethylene films were surface grafted with glycidyl methacrylate (GMA) by UV irradiating the film for 5 min together with benzophenone. Poly(ethylene glycol) (PEG) was attached to the grafted surface through reaction with the epoxy groups. This yielded a surface which consisted of 95% PEG as measured with ESCA. The adsorption of human transferrin onto this film was significantly reduced as compared with a pure polyethylene film. Heparin was also reacted with a GMA grafted PE surface. ESCA showed that heparin was grafted to the surface, and in vitro blood clotting tests on the heparinized PE surface showed a reduced thrombus formation. GMA grafted polystyrene wells were reacted with carbohydrazide, to the formed carbohydrazide surface a rabbit antibody raised against mouse urinary protein (RaMUP) was covalently coupled. The RaMUP coupled surfaces was used in the detection of mouse urinary protein (MUP) at low concentrations (ca. 1 ng/mL) with an ELISA technique.     

Reactive compatibilization of blends of PET and PP modified by GMA grafting

The melt radical grafting of glycidyl methacrylate (GMA) onto isotactic polypropylene (PP) was carried out in Brabender internal mixer and the influence of reaction procedure, radical initiator concentration and addition of co-monomer (styrene) on the grafting efficiency was examined. The viscosity, the thermal behaviour and melt rheology of PP-g-GMA samples was then analysed as a function of grafted GMA content. Blends of poly(ethylene terephthalate) (PET) with PP and PP-g-GMA (5.2 wt% GMA), prepared in internal mixer, were characterised by SEM, DSC and melt viscosimetry. The morphological analysis of PET/PP-g-GMA blends (80/20, 50/50 w/w) pointed out a marked improvement of phase dispersion (with particle size of about 0.6 μm for 80/20 blend) and interfacial adhesion, as compared to non-compatibilized PET/PP blend. The results of mixing torque and thermal analysis supported the occurrence of in-situ compatibilization reaction between epoxy groups of GMA modified PP and carboxyl end-groups of PET in the melt.     

Effect of novel compatibilizers on the properties and morphology of PP/PC blends

A series of compatibilizers, including polypropylene (PP) grafted with 2‐tertbutyl‐6‐(3‐tertbutyl‐ 2‐hydroxy‐5‐methylbenzyl)‐4‐methylphenyl acrylic ester (BPA), glycidyl methacrylate (GMA), GMA/styrene (GMA‐st), and 2‐allyl bisphenol A (2A) were investigated for the purpose of improving the compatibility of PP/polycarbonate (PC) blends. PP‐g‐BPA shows a remarkable compatibilizing effect on PP/PC blends since it has similar group‐benzene ring with PC, and it is a sort of heat‐resistant antioxidant in the meantime, which can reduce the molecular degradation of PP during grafting and blending under high temperatures. Its compatibilizing effect was examined in terms of the mechanical, thermal properties, and morphologies. PP/PC blends show a decreasing and much more homogeneous size of dispersed PC particles through addition of a small amount of PP‐g‐BPA, and dynamic mechanical analysis (DMA) reveals a noticeable approach of T_g between PP and PC, indicating the improvement of the compatibility of PP/PC blends. Furthermore, styrene‐ethylene‐butylene‐styrene (SEBS) as a toughening rubber and a compatibilizer was applied to PP/PC blends. Around 25 wt% SEBS and 20 wt% PC lead to high toughness and strength of PP. Copyright © 2008 John Wiley & Sons, Ltd.