Mechanical and thermal properties of polypeptide modified hydroxyapatite/poly(L-lactide) nanocomposites

A new type of polypeptide(poly(-benzyl-L-glutamate)(PBLG))modified hydroxyapatite(HA)/poly(L-lactide)(PLLA)nanocomposites(PBLG-g-HA/PLLA)were prepared by the solvent-mixing method,and their mechanical and thermal properties were investigated.The tensile test showed that the mechanical properties of PBLG-g-HA/PLLA nanocomposites were better than that of PLLA,even a 0.3 wt%content of PBLG-g-HA in the nanocomposites could make the tensile strength 12%higher than that of the neat PLLA sample,and the tensile mod...     

Composites of poly(L‐lactide‐trimethylene carbonate‐glycolide) and surface modified SBA‐15 as bone repair material

This work aims to develop novel composites from a poly(L ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer and mesoporous silica (SBA‐15) nanofillers surface modified by post‐synthetic functionalization. SBA‐15 first reacts with a silane coupling agent, γ‐aminopropyl‐trimethoxysilane to introduce ammonium group. PLLA chains were then grafted on the surface of SBA‐15 through ammonium initiated ring‐opening polymerization of L ‐lactide. Composites were prepared via solution mixing of PLTG terpolymer and surface modified SBA‐15. The structures and properties of pure SBA‐15, γ‐aminopropyl‐trimethoxysilane modified SBA‐15 (H₂N‐SBA‐15), PLLA modified SBA‐15 (PLLA‐NH‐SBA‐15), and PLTG/PLLA‐NH‐SBA‐15 composites were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, N₂ adsorption‐desorption, differential scanning calorimetry, contact angle measurement, and mechanical testing. The results demonstrated that PLLA chains were successfully grafted onto the surface of SBA‐15 with grafting amounts up to 16 wt.%. The PLTG/PLLA‐NH‐SBA‐15 composites exhibit good mechanical properties. The tensile strength, Young's modulus, and elongation at break of the composite containing 5 wt.% of PLLA‐NH‐SBA‐15 were 39.9 MPa, 1.3 GPa, and 273.6%, respectively, which were all higher than those of neat PLTG or of the composite containing 5 wt.% of pure SBA‐15. Cytocompatibility tests showed that the composites present very low cytotoxicity.     

Investigating properties of poly (ether‐amide)/MWCNT nanocomposite films containing 2,7‐bis(4‐aminophenoxy)naphthalene and isophthalic segments

Three nanocomposite films based on aramid (poly (ether‐amide), PEA) and multiwall carbon nanotubes (MWCNT) were prepared via solution casting method using 2,7‐bis(4‐aminophenoxy)naphthalene (4) and isophthalic acid (5) containing various amounts of MWCNT (2, 3, 5 wt.%). To comprehensively analyze the properties of the cast films as well as the monomers, different techniques were employed, namely FT‐IR, ¹H NMR, X‐ray diffraction, and field emission scanning electron microscopy. Also, thermal and tensile properties of PEA (6) and nanocomposite films were investigated using thermogravimetric analysis and mechanical analysis, respectively. The morphology, thermal, and mechanical properties of nanocomposite films approved that MWCNT had well dispersion in the PEA matrix and showed a synergistic effect on improving all of the investigated properties. Based on the thermogravimetric analysis results, employing MWCNT caused to increase in the char yields from 61 (in the neat PEA) to 66 (in the PEA /MWCNT nanocomposite 5 wt.%) under the nitrogen atmosphere. In comparison to the pristine PEA (426°C), the temperature at 10 losses mass % (T₁₀) was increased from 530°C to 576°C, with 2 to 5 wt.% of MWCNT. Mechanical analysis revealed that the tensile strength and initial modulus were improved by incorporating MWCNT into PEA (81.70–93.40 MPa and 2.10–2.22 GPa, respectively). Electrical conductivity of the PEA/MWCNT nanocomposites was displayed maximum value in the 5 wt.%, showing satisfactory value in many application areas. The X‐ray diffraction technique was employed to study the crystalline structure of the prepared nanocomposite films as well as PEA. In addition, the electrochemical impedance spectroscopy study demonstrated that the prepared nanocomposites had significant impedance improvement in the presence of MWCNTs.     

Preparation and properties of the biodegradable graded blend of poly(L‐lactic acid) and poly(ethylene oxide)

We prepared biodegradable poly(ethylene oxide) (PEO)/poly(L ‐lactic acid) (PLLA) graded blends by the dissolution–diffusion process, and discussed the biodegradability and tensile strength of the graded blends by comparing isotropic blend and PLLA only. All the graded blends were degraded more largely than the PLLA only and isotropic blend (PEO: 37.5 wt %), which had the same content as the total content of those graded blends. The graded blend having most excellent wide compositional gradient was degraded most largely with the enzyme. Thus, graded structure of the blends promoted their biodegradabilities large. It was considered that the dissolution of PEO with water increased the surface area attacked by the enzyme, while PEO caught PLLA oligomers to promote the biodegradation of PLLA. Then, the biodegradabilities of the graded blends were suppressed by the increasing crystallinity of PLLA. Furthermore, the strengths of all the graded blends were larger than those of the isotropic blend. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2972–2981, 2007     

Nanocomposites of poly(l-lactide) and surface-grafted TiO2 nanoparticles: Synthesis and characterization

A new method of surface modification of TiO₂ nanoparticles by surface-grafting l-lactic acid oligomer was developed. The surface-grafting reaction was evaluated by Fourier transformation infrared (FTIR) and thermal gravimetric analysis (TGA). The results showed that l-lactic acid oligomer could be easily grafted onto the TiO₂ nanoparticles surface in the presence of stannous octanoate and the highest amount of grafted polymer was about 8.5% in weight. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) results showed that grafted TiO₂ (g-TiO₂) in chloroform or PLLA matrix approximated to uniform, while unmodified TiO₂ nanoparticles tended to aggregate. The tensile strength of this material was greatly improved by the addition of g-TiO₂ nanoparticles in poly(l-lactide) (PLLA) matrix. The tensile strength of the g-TiO₂/PLLA nanocomposite containing 5 wt.% of g-TiO₂ was 72 MPa, which was 23.1% higher than that of pure PLLA. Even though the incorporation of the TiO₂ nanoparticles into PLLA led to the deterioration of its elongation at break, the g-TiO₂/PLLA nanocomposite also exhibited better ductility than that of TiO₂/PLLA nanocomposite.     

接枝改性POSS对PLLA结晶行为的影响*

以二氯甲烷为溶剂,利用溶液共混法将三种聚笼形多面体倍半硅氧烷(POSS)分别与聚左旋乳酸(PLLA)进行共混,制备了不同POSS含量的单氨基POSS(POSS-NH₂)/PLLA、POSS接枝聚乙二醇(POSS-PEG)/PLLA和POSS接枝聚乳酸(POSS-g-PLLA)/PLLA复合材料。利用差示扫描量热仪(DSC)、热重分析仪(TGA)、偏光显微镜(POM) 分别对复合材料的本体结晶行为、热稳定性及结晶形貌和生长速率进行了观察。结果表明当加入不同质量分数(1 wt%, 5 wt%, 10 wt%)的POSS-PEG时,PLLA的结晶能力均得到改善,而POSS-NH2和POSS-g-PLLA仅在质量分数较低(1wt%)时对PLLA起成核剂的作用,具有较高质量分数时会阻碍PLLA分子链段的运动,从而限制其结晶。三种复合材料中仅POSS-PEG在一定程度上提高了PLLA的热稳定性,利用POM观察球晶生长过程发现POSS-PEG的加入提高了PLLA的球晶生长速率。     

Poly(L‐lactide)/layered double hydroxides nanocomposites: Preparation and crystallization behavior

Novel nanocomposites from poly(L ‐lactide) (PLLA) and an organically modified layered double hydroxide (LDH) were prepared using the melt‐mixing technique. The structure and crystallization behavior of these nanocomposites were investigated by means of wide‐angle X‐ray diffraction (WAXD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), and polarized optical microscopy (POM). WAXD results indicate that the layer distance of dodecyl sulfate‐modified LDH (LDH‐DS) is increased in the PLLA/LDH composites, compared with the organically modified LDH. TEM analysis suggests that the most LDH‐DS layers disperse homogenously in the PLLA matrix in the nanometer scale with the intercalated or exfoliated structures. It was found that the incorporation of LDH‐DS has little or no discernable effect on the crystalline structure as well as the melting behavior of PLLA. However, the crystallization rate of PLLA increases with the addition of LDH‐DS. With the incorporation of 2.5 wt % LDH‐DS, the PLLA crystallization can be finished during the cooling process at 5 °C/min. With the addition of 5 wt % LDH‐DS, the half‐times of isothermal melt‐crystallization of PLLA at 100 and 120 °C reduce to 44.4% and 57.0% of those of the neat PLLA, respectively. POM observation shows that the nucleation density increases and the spherulite size of PLLA reduces distinctly with the presence of LDH‐DS. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2222–2233, 2008     

A DSC study of effect of carbon nanotubes on crystallisation behaviour of poly(ethylene oxide)

Crystallisation behaviour of poly(ethylene oxide) (PEO)/multi-walled carbon nanotubes (MWCNT) and PEO/chemically modified MWCNT nanocomposites were investigated by means of differential scanning calorimetry. Non-isothermal crystallisation experiments showed that incorporation of MWCNT and chemically modified MWCNT reduced the crystallinity and restricted the spherical crystal growth of PEO. The nucleation sites decrease and spherical crystal size increased compared to the neat PEO. Change of crystal structure from spherical to disk-like was revealed by Avrami equation when MWCNT was added up to 1 wt.%.     

Poly(L-lactide) (PLLA)/multiwalled carbon nanotube (MWCNT) composite: characterization and biocompatibility evaluation

Much effort has been directed at the fabrication of carbon nanotubes (CNTs)/polymer composites and the characterization of their physical properties. Among them, composites comprising CNTs and the biocompatible polymers are of special interest due to their potential for specific biomedical applications. we report the preparation of the MWCNT/poly(L-lactide) composite and the corresponding spectroscopic (Raman) and the microscopic (SEM, TEM) characterization. The electronic transport, thermal properties, and biocompatibility of this composite have also been investigated. The Raman spectroscopic analysis suggests the interaction between PLLA and MWCNT occurs mainly through the hydrophobic C-CH3 functional groups. The DC conductivity of the composite increases as the MWCNT loading is increased. Such behavior can be described by a percolation mechanism in which a percolation threshold at about 14 wt % MWCNT loading is observed with the maximum end conductivity of 0.1 S x cm(-1). The DSC study of the PLLA/MWCNT composite reveals that the MWCNTs in the composite have the effect of inducing crystallization and plasticizing the polymer matrix. The results from the cell culture test suggest that the presence of MWCNT in the composite inhibits the growth of the fibroblast cells.     

Electrospun Aligned Poly(L-lactide)/Poly(ϵ-caprolactone) /Poly(ethylene glycol) Blend Fibrous Membranes

Aligned poly(L-lactide) (PLLA)/poly(?-caprolactone) (PCL)/poly(ethylene glycol)(PEG) fibrous membranes were fabricated by electrospinning. Their morphology, thermal stability, mechanical properties, hydrophilic properties and in vitro degradation behaviors were investigated. With increasing the content of PEG, the PLLA/PCL/PEG blend fibers become thinner due to the increment in solution conductivity and decrease in solution viscosity. The thermal stability, hydrophilic properties, the tensile strength and elongation-at-break of PLLA/PCL/PEG blend fibrous membranes were improved, but porosity were decreased with the content of PEG changing from 10 wt% to 30 wt%. Furthermore, the incorporation of PEG enhanced the degradation of the PLLA/PCL/PEG fibrous membranes due to the better hydrophilic properties. In addition, the PLLA/PCL/PEG fibrous membranes have no toxic effect on proliferation of adipose-derived stem cells.     

High strength toughened epoxy nanocomposite based on poly(ether sulfone)‐grafted multi‐walled carbon nanotube

Hydroxyl terminated poly(ether sulfone) (PES) has been grafted on multi‐walled carbon nanotube (MWCNT). The grafting reaction was confirmed by different characterization techniques such as Fourier transform infrared spectroscopy, Raman spectroscopy, thermogravimetric analysis, and transmission electron microscopy. The extent of the grafting was found to be around 58 wt%. Hybrid nanocomposite of epoxy with the modified MWCNT was also prepared. Effect of grafting on the mechanical, thermal, and viscoelastic properties was studied. Dynamic mechanical studies show an increase in the storage modulus for the nanocomposite prepared using PES‐grafted MWCNT compared with neat epoxy system. PES‐grafted MWCNT–epoxy nanocomposite induces a significant increase in both tensile strength (26%) and fracture toughness (125%) of the epoxy matrix. Field emission scanning electron micrographs of fractured surfaces were examined to understand the toughening mechanism. Copyright © 2015 John Wiley & Sons, Ltd.     

Surface‐modified hydroxyapatite linked by L‐lactic acid oligomer in the absence of catalyst

A new surface modification method of hydroxyapatite nanoparticles (n‐HA) by surface grafting reaction of L ‐lactic acid oligomer with carboxyl terminal (LAc oligomer) in the absence of any catalyst was developed. The LAc oligomer with a certain molecular weight was directly synthesized by condensation of L ‐lactic acid. Surface‐modified HA nanoparticles (p‐HA) were attested by Fourier transformation infrared spectroscopy, ³¹P MAS‐NMR, and thermal gravimetric analysis (TGA). The results showed that LAc oligomer could be grafted onto the n‐HA surface by forming a Ca carboxylate bond. The grafting amount of LAc oligomer was about 13.3 wt %. The p‐HA/PLLA composites showed good mechanical properties and uniform microstructure. The tensile strength and modulus of the p‐HA/PLLA composite containing 15 wt % of p‐HA were 68.7 MPa and 2.1 GPa, respectively, while those of the n‐HA/PLLA composites were 43 MPa and 1.6 GPa, respectively. The p‐HA/PLLA composites had better thermal stability than n‐HA/PLLA composites and neat PLLA had, as determined by isothermal TGA. The hydrolytic degradation behavior of the composites in phosphate buffered saline (PBS, pH 7.4) was investigated. The p‐HA/PLLA composites lost their mechanical properties more slowly than did n‐HA/PLLA composites in PBS because of their reinforced adhesion between the HA filler and PLLA matrix. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5177–5185, 2005     

Morphology,rheological and crystallization behavior in thermoplastic polyurethane toughed poly(l-lactide) with stereocomplex crystallites

Melt-blending poly(l-lactide) (PLLA) with elastomers has been well demonstrated to improve toughness of PLLA. Here, we show a poly(d-lactide) (PDLA) grafted thermoplastic polyurethane (TPU) (TPU-g-PDLA) toughed PLLA with simultaneous formation of few amount stereocomplex crystallites (SCs) which exhibited higher efficient toughening than that of PLLA with TPU. The TPU-g-PDLA was prepared by the in-situ melt-reaction of TPU and PDLA with 4, 4’-diphenylmethane diisocyanate (MDI). A comparative study on morphology, rheological and crystallization behavior was also carried in PLLA/TPU, PLLA/TPU-g-PDLA and PLLA/TPU/PDLA samples. The PLLA/TPU-g-PDLA samples show the highest crystallization rate, complex viscosity, impact strength and tensile strength among PLLA/TPU, PLLA/TPU-g-PDLA and PLLA/TPU/PDLA samples, indicating that the higher interfacial interaction between TPU-g-PDLA and PLLA. Furthermore, TPU chains in TPU-g-PDLA were thought to break the intermolecular interaction of PLLA and rapid its crystallization and increase crystallinity.     

In situ polymerization of methyl methacrylate/multi-walled carbon nanotube composites using cationic stearyl methacrylate copolymers as dispersants

Novel water-soluble amphiphilic copolymers (poly[(stearyl methacrylate)-stat-([2-(methacryloyloxy)ethyl] trimethyl ammonium iodide)]) for dispersing multi-walled carbon nanotubes (MWCNTs) were used to carry out in situ methyl methacrylate (MMA) polymerization. The morphology of the poly(methyl methacrylate)/MWCNT composites and the dispersion of the MWCNTs were analyzed by transmission electron microscopy. The dispersion of multi-walled carbon nanotubes in the composites was excellent for cationic SMA (stearyl methacrylate) copolymers, even at high MWCNT loading (6.0 wt.%). The mechanical properties and electrical and thermal conductivities of the composites were also analyzed. Mechanical properties were improved by MWCNTs; the strain at break values remained stable up to 6.0 wt.% MWCNT loading. Both electrical and thermal conductivities were improved by the addition of MWCNTs.     

Cellulose Nanocrystals-mediated Phase Morphology of PLLA/TPU Blends for 3D Printing

Incorporation of nanoparticles into polymer blend to obtain finely dispersed morphology has been considered as an effective strategy to prepare nanocomposites. Owing to the renewable and degradable characters, cellulose nanocrystals(CNCs) have been proposed to tailor the phase morphology of poly(L-lactic acid)(PLLA) blend for producing high-performance fused deposition modeling(FDM) consumables. However,the main challenge associated with the ternary systems is the dispersion of the highly hydrophilic CNCs in non-polar PLLA blend by industrial melt blending without involving solution. Herein, with poly(vinyl acetate)(PVAc) modified CNCs powder(a mixture of PVAc grafted from CNCs and PVAc homopolymer latex), the selective dispersion of CNCs in PLLA has been achieved by simple melt processing of PLLA/TPU(polyether polyurethane)/CNCs blend. This results in the ultra-fine TPU droplets at nanoscale in PLLA and improves the melt processibility of composites in FDM due to the decreased viscosity ratio of the dispersed/matrix and the enhanced melt elasticity of PLLA. Combined with the intensive shear and continuous stretch effect during FDM, aligned TPU nanofibers(TNFs) were in situ formed along the elongational flow direction during deposition, which in turn contributed to the improvement of PLLA/TPU/CNCs with 5 wt% filler loading in tensile ductility by 418%, inter-layer adhesion strength and notched impact toughness by 261% and 210%, respectively, as well as achieved good dimensional accuracy and very fine surface quality.     

PTMG-Modified MWCNT/PTMG-based polyurethane nanocomposites: Strong interaction and homogeneous dispersion

Soft and flexible chains of poly(tetramethylene glycol) (PTMG) were covalently grafted with multi-walled carbon nanotubes (MWCNT). FE-SEM images showed that the polyether PTMG formed a surrounding shell around the nanotubes with about 5 nm in thickness. The modified nanotubes (MWCNT-PTMG) were then loaded into an in situ prepared polyurethane elastomer (PUE) with different loading contents below 1 wt %. In addition to the modifier of MWCNT, polyether PTMG was also used for preparing the polyurethane matrix. Thermal analyses (TG/DTG and DTA) showed two endothermic phase transitions in associated with the two main thermo-degradations of the resulting PUE nanocomposites. Moreover, DMA technique exhibited an appreciable increase in the T _g values due to a strong interaction between PTMG-modified MWCNT and PTMG-based PUE matrix.     

Improvement of thermal conductivity of poly(dimethyl siloxane) using silica-coated multi-walled carbon nanotube

In order to enhance the thermal conductivity of MWCNT filled poly(dimethyl siloxane) (PDMS) composites, the MWCNT was coated with silica layer by three step reactions. The composites filled with raw and silica-coated MWCNTs were prepared and the properties were investigated in terms of the curing characteristics, mechanical properties, and thermal conductivity. Due to the poor compatibility between raw MWCNT and PDMS, raw MWCNT showed poor dispersion uniformity and wettability in PDMS. On the other hand, due to the chemical affinity between silica/MWCNT and PDMS throughout the hydrogen bonding, the silica-coated MWCNT filled PDMS showed improved mechanical properties in terms of tensile strength and 100% modulus, and good interfacial compatibility than raw MWCNT incorporated PDMS. Finally, the good wettability of silica/MWCNT in PDMS resulted in higher thermal conductivity caused from the facile phonon movement at the interface even with the smaller MWCNT contents.     

Synthesis,stereocomplex crystallization and properties of poly(l‐lactide)/four‐armed star poly(d‐lactide) functionalized carbon nanotubes nanocomposites

Functionalized carbon nanotubes (F‐CNTs) were synthesized through the nucleophilic substitution reaction between four‐armed star poly(d ‐lactide) (4PDLA) and acryl chloride of carbon nanotubes and were characterized using Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy and thermogravimetric analysis. The results indicated that the 4PDLA was successfully grafted onto carbon nanotubes, and it contained 45.5 wt% of 4PDLA. Poly(l ‐lactide) (PLLA) nanocomposites with different F‐CNTs content were prepared by solution casting. Optical microscopy and scanning electron microscopy results showed that F‐CNTs were uniformly dispersed in the nanocomposites. Crystallization behavior and crystal structure of PLLA nanocomposites were investigated using differential scanning calorimetry, polarizing microscope and X‐ray diffraction. The results found that poly(lactide) stereocomplex crystal could be formed between PLLA and F‐CNTs. F‐CNTs played different roles in the process of solution casting and melting crystallization. Polarizing microscope also revealed that crystallization temperature had a significant effect on the nucleation and spherulites growth of PLLA. Thermal stability and mechanical properties of the nanocomposites were also investigated by thermogravimetric analysis, dynamic mechanical analysis and tensile testing. These results demonstrated that the addition of F‐CNTs obviously improved thermal stability and tensile strength of PLLA. The results showed that PLLA/F‐CNTs would have potential values in engineering fields. Copyright © 2015 John Wiley & Sons, Ltd.     

Antiflaming poly(L-lactide) by synthesizing polyurethane with phosphorus and nitrogen

A novel polyurethane containing phosphorus and nitrogen (PU) was synthesized and characterized with ¹H-NMR, FTIR, and GPC. It was served as flame retardant to blend with poly(L-lactide) (PLLA) through solution casting technique. PU particle dispersed in PLLA substrate irregularly and improved the crystallinity of PLLA. The initial decomposition temperature of PLLA composite was significantly lower, but char residue increased. Flame retardancy and mechanical properties of PU/PLLA blends were evaluated. When the blend ratio of PU/PLLA was 10 wt%, LOI was 26.8%, and UL94 test reached V-2 grade. The inflaming retarding mechanism was outlined. The tensile strength of PLLA blend was 42.8 MPa, while its elongation at break was only 2%. By adjusting PU and adding compatilizer, the balance between flame retardancy and good mechanical properties of PLLA would be controlled.