溴代烷烃与活性氮的反应发光研究

在流动余辉装置上, 利用N₂空心阴极放电制备活性氮, 研究了活性氮与溴代烷烃(CHBr₃、CH₂Br₂、C₂H₅Br、C₄H₉Br) 反应的化学发光.上述所有反应中, 在550～750 nm波段均观察到了较强的NBr (b¹Σ+→X³Σ^-)跃迁发射谱. 同时在活性氮与CHBr₃和CH₂Br₂的反应中, 在流动管下游还观察到了CN (A²π, B²π→X²Σ⁺)的发射谱. 验证性的实验表明, 激发态NBr (b¹Σ⁺)是由二步过程形成: N(⁴S)与溴代烷烃反应生成NBr (X³Σ^-), 再通过N₂ (A ³Σ_u⁺)分子能量转移到激发态NBr (b¹Σ⁺); 而激发态的CN是通过N(⁴S) + CBr→CN(A, B) + Br过程形成的.     

不同温度下VUV光激发的Pr3+离子的发光性质

The luminescent properties of Pr³⁺-doped LaB₃O₆, SrAl₁₂O₁₉, SrB₄O₇ and NaYF₄ in the vaccum ultraviol-et (VUV) range at different temperatures were investigated under the excitation of high-energetic synchrotron radiation. For Pr³⁺ ions in LaB₃O₆, SrAl₁₂O₁₉ and SrB₄O₇, only the parity-forbidden ¹S₀→4f² transitions were observ-ed in the emission spectra at relatively low temperature; but the parity-allowed 4f5d→4f² transitions appeared simultaneously when the temperature was high enough. And the intensity of broad 4f5d→4f² emission increased relative to the intensity of ¹S₀→4f² emissions with increasing temperature. Then the thermal equilibrium model of energy levels was employed to the lowest 4f5d state and ¹S₀ state of Pr³⁺ in the three hosts. The calculated curves were in good agreement with the experimental values, indicating the occurrence of the thermal excitation from ¹S₀ state to 4f5d states at high temperatures when the lowest 4f5d state lies higher than ¹S₀ state and the photon energy is high enough.     

新半金属Fe2LaO4磁电性能的第一性原理计算

利用基于密度泛函理论的第一性原理赝势法设计并优化了含稀土元素的新半金属Fe₂LaO₄。详细计算了其电荷分布,分子磁矩等磁电性能，并结合配位场理论分析了其电子结构。结果表明，Fe₂LaO₄是一种含稀土元素的铁磁性的新ⅡB型半金属；它的稳定相晶格常数约为0.623 nm，分子磁矩约为1.0μ_B；Fe₂LaO₄属软铁磁性半金属；La较多的外层电子增强了Fe₂LaO₄内部的库仑斥力,导致了配合物ML₄和ML₆均受强场作用,从而使Fe₂LaO₄具有软铁磁性；考虑自旋分布后ML₄和ML₆的电子结构分别为a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓e_g²↑e_g²↓t_2g³↑t_2g³↓和a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓t_2g³↑t_2g³↓e_g²↑e_g²↓e_g^*1↑,这些电子属于分子轨道。     

白光LED用Sr0.955Al2Si2-xTixO8：Eu2+荧光粉的晶体结构和光谱特性

由高温固相反应制得Sr_0.955Al₂Si_2-xTi_xO₈：Eu²⁺（x=0~1.0）系列试样,研究了Ti⁴⁺置换Si⁴⁺对其晶体结构和光谱特性的影响。Ti⁴⁺以类质同相替代Si⁴⁺进入晶体晶格中,形成了连续固溶体,其晶胞参数a,b,c,β和晶胞体积V随Ti⁴⁺置换量呈线性递增。Ti⁴⁺置换Si⁴⁺对晶胞参数c的影响显著,b其次,a最小。荧光激发谱为宽带,位于230~400nm,由267nm、305nm、350nm和375nm 4个峰拟合成,表观峰值位于351nm;随着Ti⁴⁺置换量的增加,半高宽（FWHM）从105nm减小到93nm。发射光谱位于380~600nm,表观峰值位于407nm,可由406nm和441nm两峰拟合而成并且随Ti⁴⁺置换量增加线性红移,Ti⁴⁺进入晶格对长波长发射中心影响较少;Ti⁴⁺置换量为1.0时,表观发射峰位从407nm红移至417nm;利用试样荧光光谱和VanUitert经验公式,得出SrAl₂Si₂O₈：Eu²⁺中Sr²⁺的配位数为9。随着Ti⁴⁺置换量Si⁴⁺进入基质晶格,造成Eu-O距离变小,使得Eu²⁺所处的晶体场强度增强,发光中心Eu²⁺的5d能级分裂增大,造成Eu²⁺最低发射能级重心下移,两拟合谱峰峰位均呈线性红移。     

Ni-Co双金属催化剂上沼气重整制氢机理

用传统湿式浸渍法制备了La₂O₃掺杂的商业γ-Al₂O₃负载的沼气重整催化剂Ni-Co/La₂O₃-γ-Al₂O₃, 并用程序升温加氢(TPH)、程序升温氧化(TPO)、程序升温表面反应(TPSR)、程序升温脱附(TPD)及脉冲实验对催化剂进行了表征. 结果表明, 沼气重整过程中Ni-Co/La₂O₃-γ-Al₂O₃催化剂上的表面碳物种主要来源于CH₄的裂解, CO₂的贡献很小. CH₄裂解能够产生三种活性不同的碳物种, 即C_α、C_β与C_γ. 随着反应的进行, C_α物种减小而C_β与C_γ物种增加, 且C_γ物种能够转变为惰性的石墨碳. 重整反应过程中CH₄与CO₂的活化能相互促进. 催化剂表面的O物种与C反应生成CO或与CH_x反应生成CH_xO再分解为CO与吸附态的H物种, 可能是Ni-Co/La₂O₃-γ-Al₂O₃催化剂上沼气重整的速率控制步骤.     

VB2n-(n=8~12)团簇几何结构、电子及热力学特性的理论研究

基于卡里普索结构预测程序和密度泛函理论的第一性原理计算,搜索确定了VB_2n^-（n=8~12）团簇的基态和亚稳态结构。结果发现,V原子的掺杂完全改变了原硼团簇的结构并提高了原体系的稳定性。掺杂体系基态结构分别呈现高对称性的鼓状（VB₁₆^-：C_2v）、管状（VB₁₈^-：C_2v和VB₂₀^-：C_s）及笼状（VB₂₂^-：C₂和VB₂₄^-：D_3h）结构。基于基态结构,研究了体系的电荷转移和极化率,拟合出了光电子能谱、红外和拉曼谱图,分析了流变键和芳香特性。最后,研究了体系的热力学特性,讨论了温度对热力学参数的影响。     

Tm3+/Er3+/Ho3+共掺SiO2-Bi2O3-AlF3-BaF2玻璃发光性能

采用高温熔融法制备了Tm³⁺/Er³⁺/Ho³⁺共掺的铋硅酸盐50SiO₂-40Bi₂O₃-5AlF₃-5BaF₂玻璃。研究了在808 nm激光器（Laser Diode）激发下Tm³⁺/Er³⁺/Ho³⁺共掺的铋硅酸盐在2 060 nm处的发光性能,同时测试及分析了该铋硅酸盐玻璃的差热特性、吸收光谱及荧光光谱。根据吸收光谱以及Judd-Oflet理论,计算了Ho³⁺的Judd-Oflet强度参数Ω_t（t=2,4,6）以及Tm³⁺/Er³⁺/Ho³⁺相应的吸收截面。铋硅酸盐玻璃中,Tm₂O₃、Er₂O₃和Ho2O3掺杂浓度分别为0.75%、1.0%和0.5%时,2 060 nm处Ho³⁺∶⁵I₇→⁵I₈发射峰强度达到最大。对Tm³⁺/Er³⁺/Ho³⁺ 3种离子的光谱性质和离子间可能存在的能量传递也做了分析。Ho³⁺在1 953 nm处的最大吸收截面σ_abs为9.08×10^-21 cm²,在2 060 nm处的最大发射截面σem为11.68×10^-21 cm²,辐射寿命τ_mea为2.75 ms,具有良好的增益效应σ_emτ（3.212×10^-20 cm^-2·ms）。     

(Zn1-xMnx)C2O4·2H2O在空气中的热分解动力学研究

用热分析（TG-DTG/DTA）、X射线衍射（XRD）技术和透射电镜（TEM）研究了固态物质Zn_1-xMn_xC₂O₄•2H₂O在空气中热分解的过程。热分析结果表明，Zn_1-xMn_xC₂O₄•2H₂O在空气中分两步分解，其失重率与理论计算失重率相吻合。 XRD和TEM结果表明，Zn_1-xMn_xC₂O₄•2H₂O分解的最终产物为Zn_1-xMn_xO,其颗粒大小约为10-13 nm。在非等温条件下对Zn_1-xMn_xC₂O₄•2H₂O的热分解动力学进行了分析。用Friedman法和Flynn-Wall-Ozawa(FWO)法求取了分解过程的活化能E，并用多元线性回归给出了可能的机理函数。Zn_1-xMn_xC₂O₄•2H₂O两步热分解的活化能分别为155.7513 kJ/mol 和215.9397 kJ/mol。     

Eu3+离子在Ca2PbO4一维结构基质中的发光研究

A Eu³⁺-doped Ca₂PbO₄ with one-dimensional structure was prepared with a solid-state reaction method and its characteristics were investigated. The XRD results show that the substitution of Ca²⁺ by Eu³⁺ has no influence on the structure of Ca₂PbO₄. Under the excitation of ultraviolet light， the Ca₂PbO₄:Eu³⁺ phosphor exhibits strong red emission at about 618 nm which is assigned to the ⁵D₀- ⁷F₂ electric-dipole transition. The compounds Sr₂CeO₄ and Ca₂SnO₄ have the same crystal symmetry as that of Ca₂PbO₄ and it is found that the emission intensity of Ca₂PbO₄∶Eu³⁺ is higher than that of Sr₂CeO₄∶Eu³⁺ and lower than that of Ca₂SnO₄∶Eu³⁺. The excitation spectrum of Ca₂PbO₄∶Eu³⁺ appears to be a broad band with two peaks at about 289 nm and 340 nm. The former peak is attributed to the Eu³⁺-O₂- charge transfer transition， while the latter one may be related to the absorption of Ca₂PbO₄ host or its crystal defects.     

双钙钛矿型Ca2Gd1-xTaO6：xTb3+绿色荧光粉的合成与荧光性质

通过高温固相法合成了双钙钛矿型Ca₂Gd_1-xTaO₆：xTb³⁺（CGTO：xTb³⁺）绿色荧光粉。采用X射线衍射、扫描电镜、荧光光谱、荧光衰减曲线、量子效率（η）测试分别表征了CGTO： xTb³⁺荧光粉的物相、形貌和荧光性质。在紫外光激发下,CGTO： xTb³⁺荧光粉实现了较强的绿光发射,绿光为Tb³⁺离子的⁵D₄-⁷F₅跃迁。通过变温发射光谱研究发现CGTO：0.15Tb³⁺荧光粉的热猝灭活化能为0.181 9 eV。在255 nm的激发下,最佳Tb³⁺掺杂浓度的CGTO：0.15Tb³⁺荧光粉的量子效率为32.32%。     

Studies on the micropolarities of bmimBF4/TX-100/toluene ionic liquid microemulsions and their behaviors characterized by UV-visible spectroscopy

Ionic liquids (ILs), 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4), were substituted for polar water and formed nonaqueous microemulsions with toluene by the aid of nonionic surfactant TX-100. The phase behavior of the ternary system was investigated, and microregions of bmimBF4-in-toluene (IL/O), bicontinuous, and toluene-in-bmimBF4 (O/IL) were identified by traditional electrical conductivity measurements. Dynamic light scattering (DLS) revealed the formation of the IL microemulsions. The micropolarities of the IL/O microemulsions were investigated by the UV-vis spectroscopy using the methyl orange (MO) and methylene blue (MB) as absorption probes. The results indicated that the polarity of the IL/O microemulsion increased only before the IL pools were formed, whereas a relatively fixed polar microenvironment was obtained in the IL pools of the microemulsions. Moreover, UV-vis spectroscopy has also shown that ionic salt compounds such as Ni(NO3)2, CoCl2, CuCl2, and biochemical reagent riboflavin could be solubilized into the IL/O microemulsion droplets, indicating that the IL/O microemulsions have potential application in the production of metallic or semiconductor nanomaterials, and in biological extractions or as solvents for enzymatic reactions. The IL/O microemulsions may have some expected effects due to the unique features of ILs and microemulsions.     

聚乙烯吡咯烷酮存在时反相微乳液中水的状态

运用傅立叶变换红外光谱（FTIR）研究不同分子量的聚乙烯吡咯烷酮（PVP）存在时,十二烷基甜菜碱(C12BE)/正庚烷 /正戊醇 /水（Ⅰ）及二（2 乙基）己基磺化琥珀酸钠（AOT）/正庚烷 /水（Ⅱ） 反相微乳液中水的存在状态.采用计算机分峰技术将微乳液中水分子的O－H伸缩振动进行曲线拟合, （Ⅰ）得到三个子峰,分别位于(3560±20)cm－1,(3430±10)cm－1,(3280±10)cm－1附近; （Ⅱ）得到四个子峰,分别位于3618 cm－1, 3550 cm－1, 3446 cm－1和3292 cm－1处.尽管PVP均增溶于W/O型微乳液中表面活性剂分子的极性基团附近,却没有引起长链间自由水的变化.但由于两体系的差异,PVP的存在,导致微乳液（Ⅰ）的本体水减少,结合水增多,却使体系（Ⅱ）的结合水减少,本体水增多.由于W/O型微乳液中水与生物膜中水相似,这些研究有助于理解生物膜界面上的生物化学和生物物理现象.     

Structural studies of 1-butyl-3-methylimidazolium tetrafluoroborate/TX-100/ p-xylene ionic liquid microemulsions.

The ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) forms nonaqueous microemulsions with p-xylene, with the aid of the nonionic surfactant TX-100. The phase behavior of the ternary system is investigated, and three microregions of the microemulsions-ionic liquid-in-oil (IL/O), bicontinuous, and oil-in-ionic liquid (O/IL)-are identified by conductivity measurements, according to percolation theory. On the basis of a phase diagram, a series of IL/O microemulsions are chosen and characterized by dynamic light scattering (DLS). The size of aggregates increases on increasing the amount of added polar component (bmimBF(4)), which is a similar phenomenon to that observed for typical water-in-oil (W/O) microemulsions, suggesting the formation of IL/O microemulsions. The microstructural characteristics of the microemulsions are investigated by FTIR and 1H NMR spectroscopy. The results indicate that the interaction between the electronegative oxygen atoms of the oxyethylene (OE) units in TX-100 and the electropositive imidazolium ring may be the driving force for the solubilization of bmimBF4 into the core of the TX-100 aggregates. In addition, the micropolarity of the microemulsions is investigated by using methyl orange (MO) as a UV/Vis spectroscopic probe. A relatively constant polarity of the microemulsion droplets is obtained in the IL microemulsion. Finally, a plausible structure for the IL/O microemulsion is presented.     

Application of surfactants and microemulsions to the extraction of pyrene and phenanthrene from soil with three different extraction methods

In the present work, the use of surfactants and oil-in-water (O/W) microemulsions as alternative extractants in accelerated solvent extraction (ASE) for the extraction of polycyclic aromatic hydrocarbons (pyrene and phenanthrene) from soils was investigated. In particular, the effect of each individual component within the microemulsions, i.e., oil phase, surfactant and co-surfactatnt, and extraction conditions on the percentage recovery was systematically studied. When compared to the water and organic solvent, the important findings were that the common surfactant solutions at the concentrations above their critical micelle concentrations (CMC) were shown to enhance the percentage recovery at the lower extraction temperature. Moreover, the highest percentage recovery can be obtained using microemulsion as the extractant. The chemical component within the microemulsions and relative amounts of the oil phase appeared to play a much more significant role in ensuring high percentage recovery. Finally, an overall comparison between the percentage recoveries obtained with ultrasound-assisted extraction (UAE), microwave-assisted extraction (MAE) and ASE using organic solvents, surfactants and microemulsions as extractants was exhibited.     

SDBS／正辛烷／正丁醇／盐水体系中相微乳液微观结构的研究

利用冷冻蚀刻电镜、ＦＴ－ＩＲ、ＥＳＲ和ＮＭＲ方法研究了ＳＤＢＳ／ｎ－Ｃ４Ｈ９ＯＨ／ｎ－Ｃ８Ｈ１８盐水体系中相微乳液微观结构。四种方法均表现随着体系含盐度的增加，中相微乳液微观结构经历了从Ｏ／Ｗ型到Ｂ．Ｃ型，再到Ｗ／Ｏ型的转变。     

Comparison of microstructures of microemulsion and swollen micelle in electrokinetic chromatography

Recently, 1-butanol modified MEKC was proven to be similar to MEEKC in separation performance. In the present work, typical microemulsion containing 0.8% n-octane/3.3% SDS/6.6% 1-butanol/20 mM borax buffer and corresponding swollen micelle without n-octane were used to compare their microdroplet structures including hydrodynamic radius, electrokinetic potential ζ and charge density at the hydrodynamic shear surface, as well as microenvironment polarity in the interior of the microdroplets. Three kinds of corticosteroids were separated with MEEKC and 1-butanol modified MEKC to assess their separation performances. The experiment results showed that both microstructure and separation performance in microemulsion and in swollen micelle systems were alike, no matter whether oil phase n-octane was present. The environment polarity in the core of swollen micelle was slightly higher than in the microemulsions, and both of them were higher than in n-octane medium. Furthermore, the influences of SDS and 1-butanol concentration on microstructures were measured in details. Increasing the amount of SDS, hydrodynamic radius decreased in microemulsion but increased in swollen micelle. On the contrary, ζ and shear surface charge density changed in the reverse trends. With increment of 1-butanol concentration, the hydrodynamic radius increased dramatically in microemulsions, whereas decreased slightly in swollen micelle. Even though using n-octane as oil core was not a key factor, microemulsions and swollen micelle as pseudostationary phase in EKC should not be exactly the same.     

微乳液结构的研究

测定了十二烷基磺酸钠／正丁醇／２０％苯乙烯／水体系的相平衡，用冷冻刻蚀、ＥＳＲ、ＦＴ－ＩＲ研究了上述体系微乳液的结构，研究表明，苯乙烯含量恒定时，随着体系中水含量增加，电导确定的双连续结构的微乳液经历着从油包水到以连续再到水包油变化，ＦＴ－ＩＲ测定表明，Ｗ／Ｏ微乳兴较Ｏ／Ｗ微乳液的ＯＨ伸缩振动和弯曲振动频率有显著减小，说明Ｗ／Ｏ微乳兴中氢键缔合要比Ｏ／Ｗ强得多。ＥＳＲ测定表明Ｏ／Ｗ微乳液的旋转相关     

Phase Behavior and Dielectric Spectroscopy of the Sodium Dodecyl Trioxyethylene Sulfate／n－Butanol／Water System

Introduction　　Itiswellknownthatsurfactantsinanaqueoussolu tioncouldformmicellesataconcentrationhigherthanthecriticalmicelleconcentration (cmc) .Knowledgeofalcoholsolubilizationinaqueousmicellesolutionsisimportantinunderstandingtheaggregationbehaviorofsuchsystemsandisrelevanttoseveralindustrialprocesses .1Manystudieshavebeenreportedonphasebehaviorofternarysystemsofionicsurfactant,alcohol,andwater.2 7Generally ,inthecaseofshortchainalcohol,atransparent,isotropic ,andlow viscosityphaseappearse…     

Microemulsion polymerization of acrylamide and styrene: Effect of the structures of reaction media

Isothermal phase diagrams of the system cetyltrimethylammonium bromide (CTAB)/n‐butanol/n‐octane/water were constructed, and the effect of the oil (n‐octane) contents on the microemulsions was studied at 40 °C. We determined the microemulsion structures of two systems, CTAB/n‐butanol/10% n‐octane/water and sodium dodecyl sulfonate (As)/n‐butanol/20% styrene/water, by conductivity measurements to investigate the polymerization of acrylamide and styrene in the two microemulsion systems. The polymerization kinetics of the water‐soluble monomer acrylamide in CTAB micelles and the different CTAB/n‐butanol/10% n‐octane/water microemulsion media [water‐in‐oil (W/O), bicontinuous (BC), and oil‐in‐water (O/W)] were studied with water‐soluble sodium bisulfite as the initiator. The maximum polymerization rate in CTAB micelles was found at the second critical micelle concentration. A mechanism of polyacrylamide formation and growth was proposed. A connection between the structures of the microemulsions and the polymerization rates was observed; the maximum polymerization rate occurred at two transition points, from W/O to BC and from BC to O/W, and the polyacrylamide molecular weights, which depended on the structures of the microemulsions, were also found. A square‐root dependence of the polymerization rates on the initiator concentrations was obtained in CTAB micelles and O/W microemulsion media. The polymerization of the oil‐soluble monomer styrene in different As/n‐butanol/20% styrene/water microemulsion media (W/O, BC, and O/W) was also investigated with different initiators: water‐soluble potassium persulfate and oil‐soluble azobisisobutyronitrile. A similar connection between the structures of the microemulsions and the conversions of styrene in CTAB/n‐butanol/10% n‐octane/water for the polymerization of acrylamide was observed again. The structures of the microemulsions had an important role in the molecular weights and sizes of polystyrene. The polystyrene particles were 10–20 nm in diameter in BC microemulsion media and 30–60 nm in diameter in O/W microemulsion media according to transmission electron microscopy. We determined the solubilization site of styrene in O/W microemulsion drops by ¹H NMR spectra to analyze the results of the microemulsion polymerization of styrene. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3320–3334, 2001