Chemical synthesis, spectral characterization and stability of some electrically conducting polymers

<正>The synthesis,characterization,thermal degradation and stability of polyaniline(PANI),poly(m-nitroaniline), poly(m-chloroaniline) and poly(o-methylaniline) were reported.Different properties were measured and compared with PANI to find out the effect of electron donating groups(-CH_3) and electron withdrawing groups(-Cl,- NO_2).It was found that the presence of any type of substitution in the benzene ring of aniline increased the solubility but reduced the yield,thermal stability and electrical conductivity.Two probe methods were used to measure the electrical conductivity of these polymers.The structural properties of these polymers were characterized by using FTIR and UV-Vis spectroscopic methods.Thermal degradation and stability of these polymers were explained by using thermogravimetric analysis(TGA) and conductivity measurements.     

Graphene oxide‐induced polymerization and crystallization to produce highly conductive polyaniline/graphene oxide composite

Graphene oxide (GO)–polyaniline (PANI) composite is synthesized by in situ polymerization of aniline in the presence of GO as oxidant, resulting in highly crystalline and conductive composite. Fourier transform infrared spectrum confirms aniline polymerization in the presence of GO without using conventional oxidants. Scanning electron microscopic images show the formation of PANI nanofibers attached to GO sheets. X‐ray diffraction (XRD) patterns indicate the presence of highly crystalline PANI. The sharp peaks in XRD pattern suggest GO sheets not only play an important role in the polymerization of aniline but also in inducing highly crystalline phase of PANI in the final composite. Electrical conductivity of doped GO–PANI composite is 582.73 S m^?1, compared with 20.3 S m^?1 for GO–PANI obtained by ammonium persulfate assisted polymerization. The higher conductivity appears to be the result of higher crystallinity and/or chemical grafting of PANI to GO, which creates common conjugated paths between GO and PANI. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1545–1554     

Preparation,morphology and electrical conductivity of polyaniline/polyoxyalkylene–montmorillonite exfoliated nanocomposites

Polyaniline (PANI)/organoclay exfoliated nanocomposites containing different organoclay contents (14–50 wt%) were prepared. PANI emeraldine base (EB) and oligomeric PANI (o‐PANI) were intercalated into montmorillonite (MMT) modified by four types of polyoxyalkylene diamine or triamine (organoclay) using N‐methyl pyrolidinone (NMP) as a solvent in the presence of 0.1 M HCl. o‐PANI and EB have been synthesized by oxidative polymerization of aniline using ammonium peroxydisulfate (APS). Infrared absorption spectra (IR) confirm the electrostatic interaction between negatively charged surface of MMT and positively charged sites in PANI. X‐ray diffraction (XRD) studies disclosed that the d₀₀₁ spacing between interlamellar surface disappeared at low content of the organoclay. The morphology of these materials was examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Electrical conductivities of the PANI‐organoclay and o‐PANI‐organoclay nanocomposites were 1.5 × 10^?3–2 × 10^?4 and 9.5 × 10^?7–1.8 × 10^?9 S/cm, respectively depending on the ratio of PANI. Copyright © 2007 John Wiley & Sons, Ltd.     

Composite layers consisting of polyaniline and poly(o-phenylenediamine): Electrochemical deposition, electrochromic and electrocatalytic properties

The composite polymer layers consisting of polyaniline (PANI) and poly(o-phenylenediamine) (poly(o-PDA)) were electrodeposited on a platinum electrode by simultaneous electrochemical oxidation of corresponding monomers from aquaeous hydrochloric solutions. The growth of PANI and poly(o-PDA) occurs separately resulting in layers with two distinct, finely distributed phases. The first deposited layers are composed mainly of poly(o-PDA) and become richer in PANI as the electropolymerization proceeds. The aniline/o-PDA copolymer was not formed during electrodeposition, as evidenced by cyclic voltammetry and Fourier-transformed IR spectroscopy. It was demonstrated that the electrochromic properties of resulting composite layers are the combination of yellow/brown-reddish and green/dark blue observable color transitions which are characteristics of poly(o-PDA) and PANI, respectively. Electrocatalytic properties of the electrosynthesized composite layers were investigated on quinone/hydroquinone (Q/H₂Q) redox system and it was shown that the composite layers increase the heterogeneous electron transfer rate with a magnitudes ranging from those obtained on pure poly(o-PDA) to those obtained on pure PANI layer.     

Thermal analysis of polyaniline poly(N-vinylpyrrolidone)-stabilized dispersions

The polyaniline dispersions stabilized with poly(N-vinylpyrrolidone) (PANI/PVP) were synthesized by oxidative polymerization with different mass ratios of PANI and PVP and different molar concentrations of the components in the polymerization mixture. The composite powders prepared from colloidal PANI/PVP dispersions were characterized by thermogravimetry and differential thermal analysis. The change in the ratio of PANI and PVP as well as the starting molar concentrations of aniline hydrochloride and oxidant has influence on the resulting properties of the dispersions. Concerning the doping, the results show that PANI/PVP powders are stable up to approximately 160 °C. Degradation of polymer chains starts at temperatures above 250 °C. The PANI/PVP composite powders with lower content of PANI exhibit slightly higher thermal stability. Further, colloidal PANI/PVP dispersions were screen-printed on aluminum foil for infrared spectroscopic characterization and on poly(ethylene terephthalate) foil for electrical measurements. The sheet resistance of printed layers measured by two-point probe was of the order of tens to thousands of kΩ sq^?1. The influence of both the change in the composition and the drying temperature is discussed.     

Synthesis and characterization of some new aromatic diamine monomers from oxidative coupling of anilines and substituted aniline with 4-amino-N,N-dimethyl aniline

New aromatic diamine monomers prepared from condensation reactions of aniline, p-chloroaniline, p-nitro aniline, p-chloro-m-nitro aniline with 4-amino-N,N-dimethylaniline (2:1) (aniline:reagent) in the presence of potassium dichromate in acidic media yielded new monomers of a highly colored violet and reddish-violet. Mechanism of the reaction of aniline with 4-amino-N,N-dimethylaniline in the presence of potassium dichromate as an oxidant is expected to proceed through nucleophilic substitution reaction, and the mechanism proceeds facilitated a nucleophilic attack of the substituted aniline ring on the –NH₂ group of the reagent; through partial protonation of their –NH₂ group, forming in diamine dye and their identification was confirmed by IR, ¹H NMR, and CHN analyses.     

Effect of aniline formaldehyde resin on the conjugation length and structure of doped polyaniline: Spectral studies

A DBSA (n‐dodecylbenzene sulfate)‐complexed aniline formaldehyde [AF(DBSA)_1.0] was successfully synthesized with excess aniline (compared with formaldehyde) in the presence of n‐dodecylbenzene sulfonic acid (HDBSA), which was complexed with aniline monomer before polymerization. The resin was carefully characterized with ¹H and ¹³C NMR, electron spectroscopy for chemical analysis, and Fourier transform infrared and was demonstrated to be a polymer in which anilines were all complexed with HDBSA and became anilinium salts. A drastic decrease of the maximum absorption wavelength (ultraviolet–visible spectra) of DBSA‐doped polyaniline [PANI(DBSA)_0.5] was found when AF(DBSA)_1.0 was mixed, and this resulted from the reduced conjugation length. A similar effect on PANI(DBSA)_0.5 was found when free HDBSAs were mixed with PANI(DBSA)_0.5. Visual inspection with an optical microscope revealed that PANI(DBSA)_0.5/AF(DBSA)_1.0 gave uniform morphologies in various compositions, showing possible miscibility for this system. X‐ray diffraction patterns of PANI(DBSA)_0.5/AF(DBSA)_1.0 showed that the layered structure of PANI(DBSA)_0.5 was still present but became shorter in the polyblend because of the presence of AF(DBSA)_1.0. Solid‐state ¹³C NMR spectra revealed that the reduced conjugation length was derived from the interaction of alkyl groups between HDBSA, complexed DBSA, and dopant DBSAs. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3116–3125, 2005     

模板合成H_4PMo_(11)VO_(40)/聚苯胺纳米线列阵及其聚合机理探讨

在氧化铝模板中制备了HPA/PANI纳米线列阵,SEM、TEM表明列阵中纳米线直径约为80 nm;XRD与FT-IR证明形成了有效掺杂;单根纳米线的导电率为16.2 S.cm-1;材料的TG-DTA表明PANI纳米线材料有三步失重过程,失去吸附水过程,多酸失去结晶水和PANI结构持续分解过程,多酸结构分解过程;在氧化聚合过程中H4PMo11VO40即为质子酸又为氧化剂和掺杂剂;聚合反应采用自由基机理进行,掺杂反应发生在形成醌二亚胺式自由基正离子和双苯胺式自由基正离子和醌二亚胺式自由基正离子偶联聚合成链结构时.     

Chemical and electrochemical grafting of polyaniline onto poly(vinyl chloride): synthesis,characterization, and materials properties

We have designed and developed a new strategy for the chemical and electrochemical graft copolymerization of aniline onto poly(vinyl chloride). For this purpose, first phenylamine groups were incorporated into poly(vinyl chloride) via a nucleophilic substitution reaction in the presence of a solvent composed of 4‐aminophenol, potassium carbonate, and dry N,N‐dimethylformamide at room temperature, in order to avoid cross‐linking. The macromonomer obtained was used in chemical and electrochemical oxidation copolymerization with aniline monomer to yield a poly(vinyl chloride)‐g‐polyaniline (PVC‐g‐PANI) graft copolymer. The chemical structures of samples as representatives were characterized by means of Fourier transform infrared and ¹H nuclear magnetic resonance spectroscopies. The electroactivity behaviors of the synthesized samples were verified under cyclic voltammetric conditions. The electrical conductivity and electroactivity measurements showed that the PVC‐g‐PANI graft copolymer has lower electrical conductivity as well as electroactivity than those of the pure PANI. However, the lower electrical conductivity and electroactivity levels in this material can be improved at the price of solubility and processability. Moreover, the thermal behavior and chemical composition of the synthesized graft copolymer were investigated. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation and characterization of PVC/PANI conductive composite with extremely low percolation threshold

Aniline was polymerized in the presence of poly(vinyl chloride) (PVC) powders in hydrochloric acid to in situ prepare poly(vinyl chloride)/polyaniline (PVC/PANI) composite particles. UV‐vis spectra and FT‐IR spectra indicate PANI in PVC/PANI composite particles possessed a higher oxidation state with decreased aniline content in reactants. Both conductivity and impact strength of the dodecylbenzenesulfonic acid (DBSA) doped PANI composites (PVC/PANI‐DBSA), which were compression molded from the in situ prepared PVC/PANI particles, increase with the pressing temperature and decrease with the increase of DBSA doped PANI (PANI‐DBSA) loading. An excellent electric conductivity of 5.06 × 10^?2 S/cm and impact strength of 0.518 KJ/m² could be achieved for the in situ synthesized and subsequently compression molded composite. Copyright © 2004 John Wiley & Sons, Ltd.     

Polymerization of aniline derivatives by K2Cr2O7 and production of Cr2O3 nanoparticles

Oxidative polymerization of aniline, anthranilic acid, and aniline‐co‐anthranilic acid by potassium dichromate Cr(VI) as an oxidant in acidic medium was investigated. In this study, the polymerization process of aniline, o‐anthranilic acid as well as aniline/o‐anthranlic acid using K₂Cr₂O₇ produced, coordinated Cr(III)/polyaniline (PANI), Cr(III)/polyanthranilic acid (PAA) and Cr(III)/poly aniline‐co‐anthranilic acid (PANAA). The mechanism of polymerization reaction in the presence of dichromate was hypothesized. The precursor chromium doped polymers were characterized by TGA, FT‐IR, UV‐visible, XRD analyses. Cr₂O₃ nanoparticles size were determined using TEM analysis. The calcinations process of synthesized chromium doped PANI, PAA and PANAA yields Cr₂O₃ nanoparticles 26%, 31%, and 34% wt. respectively. Rhombohedral phase of Cr₂O₃ particles in the range from 33 to 61 nm was produced from chromium/polyanthranilic acid (PAA) and chromium/poly(aniline‐co‐anthranilic acid) PANAA. UV‐ visible analysis showed that optical band gaps (E_g) of doped poly aniline and its derivatives are in the range from1.55 to 1.80 using Tacu's law. The band gap values reveal that the doped chromium emeraldine base can be used as semiconductor materials. Copyright © 2016 John Wiley & Sons, Ltd.     

Conductive composite of polyaniline and tungsten carbide

Conductive polyaniline/tungsten carbide (PANI/TC) composite was synthesized via polymerization of the aniline monomer by (NH₄)₂S₂O₈/H₂SO₄ oxidant system in the presence of an aqueous suspension of TC. The structure, thermal stability and conductivity of PANI/TC composite were studied and the results were also compared with the pure PANI. The results showed that there was a strong interaction between the TC particles and PANI molecular chains. The crystalline structure of TC remained undisturbed upon with interaction with PANI chains. The thermal stability of PANI/TC composite was better than that of pure PANI. The direct current conductivity values of PANI/TC composite decreased slowly as the temperature increased from 25 to 165°C and PANI/TC composite exhibited significantly higher conductivity than the pure PANI.     

Synthesis, characterization and thermal analysis of polyaniline/ZrO2 composites

Conducting polyaniline-zirconium dioxide (PANI/ZrO₂) composites were synthesized by ‘in situ’ deposition technique in the presence of hydrochloric acid (HCl) as dopant by adding the fine grade powder (average particle size of approximately 20 nm) of ZrO₂ into the polymerization reaction mixture of aniline. The composites obtained were characterized by infrared spectra (IR) and X-ray diffraction (XRD) and thermogravimetric analysis (TGA). TG curves and DTG curves of the composites suggest that the thermal degradation process of PANI/ZrO₂ composites proceeds in two-steps and the composites are more thermally stable than that of the pure PANI. The improvement in the thermal stability for the composites is attributed to the interaction between PANI and ZrO₂, which restricts the thermal motion of PANI chains and shields the degradation of PANI in the composites.     

Synthesis and Characterization of Novel Nanophase Hexagonal Poly(2,5‐dimethoxyaniline)

Novel nanophase hexagonal structured polyaniline (PANI) and poly(2,5‐dimethoxyanilines) (PDMA) were synthesized by oxidative polymerization involving the respective anilines and a mixture of ferric chloride and ammonium persulfate. The morphological, spectral and electrochemical characteristics of the polymers were determined from the results of SEM, FTIR, UV‐vis, TGA and cyclic voltammetry experiments. The hexagonal PANI and PDMA nanorods (15–200 nm diameter) exhibited very good thermal stabilities, losing only 10% of their weight on heating to 400 °C. Electrochemical data indicated a pernigraniline state of the polymers with formal potential, E°′, values of 394±6 mV and 400±1 mV, for PANI (conductance, C=0.37×10^?3 S) and PDMA (conductance, C=2.02×10^?3 S), respectively. The pernigraniline state was confirmed by sharp FTIR pernigraniline quinoidic peaks (PANI: 1414 cm^?1; PDMA: 1157 cm^?1), and UV‐vis absorption maxima at 340–370 nm (PANI) and 450–650 nm (PDMA) which are characteristic of charge transfer excitons of the quinoid structures of pernigraniline.     

Metal Complexes of Aniline: Infrared and Raman Spectra

Abstract

The literature for the years 1965–1987 has been searched for all significant papers which refer to the vibrational spectra of metal complexes of aniline and substituted anilines. These papers have been reviewed with particular reference to isotopic labelling and metal ion substitution studies as assignment techniques and to the structural and bonding information which can be derived from the spectra. Compounds of the following classes are included: [M(an)₂X₂] (M = Mn, Co, Ni, Cu, Zn, Cd, Hg; an = aniline, X - Cl, Br, I, NCS); cis- and trans-[Pt(an)₂X₂] (X = Cl, Br, I, NO₂); [M(R-an)₂X₂] (M = Mn, Co, Ni, Cu, Zn; R-an = o-, m- and p-toluidine and other substituted anilines; X = Cl, Br, I); aniline adducts of metal β-ketoenolates; the complexes trans-[PtL(R-an)X₂] (L = CH₂?CH₂ or CO, R-an = aniline or a substtuted aniline, X = Cl, Br); and other miscellaneous systems comprising aniline as a ligand.     

Optimization of the thickness of a conducting polymer, polyaniline, deposited on the surface of poly(vinyl chloride) membranes: a new way to improve their potentiometric response

Repeated depositions of polyaniline (PANI) have been used to control the thickness of the polymeric film deposited on poly(vinyl chloride) (PVC) membrane surface. The oxidation of aniline was carried out in a dispersion mode, i.e. in the presence of poly(N-vinylpyrrolidone) (PVP). Two kinds of PVC were used for this purpose: a non-plasticized PVC for the study of PANI deposition and PVC, plasticized with nitrophenyl octyl ether (NPOE), as a prototype of a liquid membrane electrode. The results of UV-visible and FTIR spectroscopies and electron microscopy showed that (1) the film thickness increased by about equal increments of ∼40 nm after each polymerization, and (2) the interface with PVC was constituted by PANI film and adhering PANI-PVP colloidal particles.The various thicknesses of the deposited PANI films affected the potentiometric response of the NPOE/PVC membrane with and without an anion-exchanger. The potentiometric anionic response was observed with a minimal thickness of PANI film on the blank NPOE/PVC membrane. Sensitivity of the PANI film to pH occurred only with a blank NPOE/PVC membrane coated with a thick polymeric film, while it was strongly suppressed by the presence of a lipophilic anion-exchanger, tridodecylmethylammonium chloride (TDDMACl), in the membrane, regardless of the thickness of the polymer film. The thickness of the PANI film did not affect the anionic selectivity pattern of TDDMACl-based membranes to any great extent, but its presence improved and stabilized their potentiometric characteristics (sensitivity, linear-response range).     

Synthesis,characterization and thermal analysis of polyaniline (PANI)/Co<Subscript>3</Subscript>O<Subscript>4</Subscript> composites

Conducting polyaniline/Cobaltosic oxide (PANI/Co₃O₄) composites were synthesized for the first time, by in situ deposition technique in the presence of hydrochloric acid (HCl) as a dopant by adding the fine grade powder (an average particle size of approximately 80 nm) of Co₃O₄ into the polymerization reaction mixture of aniline. The composites obtained were characterized by infrared spectra (IR) and X-ray diffraction (XRD). The composition and the thermal stability of the composites were investigated by TG-DTG. The results suggest that the thermal stability of the composites is higher than that of the pure PANI. The improvement in the thermal stability for the composites is attributed to the interaction between PANI and nano-Co₃O₄.     

Preparation and characterization of polyaniline films in the presence of N-phenyl-1,4-phenylenediamine

The chemical oxidation of aniline to form polyaniline (PANI) films was made in the presence of N-phenyl-1,4-phenylenediamine (PPDA) in aqueous hydrochloric acid medium. The PANI films were monitored by using the quartz crystal microbalance (QCM) technique. The effect of PPDA and its concentration on the film formation was investigated. It was found that PPDA decreases the yield of the PANI film, the induction period and the depletion time of the polymerization. However, the growth rate of the film formation was found to increase by increasing PPDA concentration. These results were justified by measuring the UV-VIS absorption spectra for the in situ PANI films and the in situ UV-VIS absorption spectra for the polymer in the bulk during the polymerization. The conductivity for the PANI films at different concentrations of PPDA was measured. Also, the IR spectra, X-ray and the thermal gravimetric analysis for the PANI powder formed in the bulk in the presence of PPDA were measured and discussed.     

Polyaniline/CoFe2O4 nanocomposite inhibits the growth of Candida albicans 077 by ROS production

In recent years, polyaniline/CoFe₂O₄ nanocomposites have gained attention because of their wide utilization in optoelectronics and biomedical studies. However, very limited research has been carried out on the anticandidal activity of polyaniline/CoFe₂O₄ nanocomposite against Candida spp. Thus, the study was designed to investigate the anticandidal potential of PANI/CoFe₂O₄ nanocomposite against Candida albicans 077. PANI/CoFe₂O₄ nanocomposite (denoted as “cfPNCs”) was synthesized by polymerization of aniline in the presence of CoFe₂O₄ nanoparticles. The structural and thermal properties of the synthesized PANI/CoFe₂O₄ nanocomposite were investigated. It was noteworthy that PANI/CoFe₂O₄ nanocomposite showed promising anticandidal activity in a dose-dependent manner. Results also showed that the protection of histidine (a ROS quencher) against ROS clearly suggested the implication of ROS in anticandidal activity of PANI/CoFe₂O₄ nanocomposite. It is encouraging to conclude that PANI/CoFe₂O₄ nanocomposite bears the potential of their applications in biomedicine, especially nanotherapy for diseases caused by C. albicans.     

Synthesis and characterization of C60/polyaniline composites from interfacial polymerization

C₆₀/polyaniline (PANI) nanocomposites have been synthesized by the oxidative polymerization of aniline with ammonium peroxydisulfate in the presence of C₆₀ by using an interfacial reaction. When compared with the pure PANI nanofibers from the similar process, the diameter of the obtained C₆₀/PANI nanofibers was increased because of the encapsulation of C₆₀ into PANI during aniline polymerization, which resulted from the charge‐transfer interactions between C₆₀ and aniline fragment in PANI. In addition, the resulting C₆₀/PANI nanocomposites synthesized from the low initial C₆₀/aniline molar ratio (less than 1:25) showed the homogenous morphology composed of fiber network structures, which has an electrical conductivity as high as 1.1 × 10^?4 S/cm. However, the C₆₀/PANI nanocomposites from the higher initial C₆₀/aniline molar ratio (more than 1:15) showed the nonuniformly distributed morphology, and the electrical conductivity was decreased to 3.5 × 10^?5 S/cm. Moreover, the C₆₀/PANI nanocomposites from the interfacial reaction showed a higher value of electrical conductivity than the mechanically mixed C₆₀/PANI blends with the same C₆₀ content, because of the more evenly distributed microstructures. FTIR, UV–vis, and CV data confirmed the presence of C₆₀ and the significant charge‐transfer interactions in the resultant nanocomposites, which was responsible for the morphology development of the C₆₀/PANI and the variation of the electrical conductivity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012