Seeded-growth approach to fabrication of silver nanoparticle films on silicon for electrochemical ATR surface-enhanced IR absorption spectroscopy

Ag nanoparticle films (simplified as nanofilms hereafter) on Si for electrochemical ATR surface enhanced IR absorption spectroscopy (ATR-SEIRAS) have been successfully fabricated by using chemical deposition, which incorporates initial embedding of Ag seeds on the reflecting plane of an ATR Si prism and subsequent chemical plating of conductive and SEIRA-active Ag nanofilms. Two alternative methods for embedding initial Ag seeds have been developed: one is based on self-assembly of Ag colloids on an aminosilanized Si surface, whereas the other the reduction of Ag+ in a HF-containing solution. A modified silver-mirror reaction was employed for further growth of Ag seeds into Ag nanofilm electrodes with a theoretically average thickness of 40-50 nm. Both Ag seeds and as-deposited Ag nanofilms display island structure morphologies facilitating SEIRA, as revealed by AFM imaging. The cyclic voltammetric feature of the as-prepared Ag nanofilm electrodes is close to that of a polycrystalline bulk Ag electrode. With thiocyanate as a surface probe, enhancement factors of ca. 50-80 were estimated for the as-deposited Ag nanofilms as compared to a mechanically polished Ag electrode in the conventional IRAS after reasonable calibration of surface roughness factor, incident angles, surface coverage, and polarization states. As a preliminary example for extended application, the pyridine adsorption configuration at an as-deposited Ag electrode was re-examined by ATR-SEIRAS. The results revealed that pyridine molecules are bound via N end to the Ag electrode with its ring plane perpendicular or slightly tilted to the local surface without rotating its C2 axis about the surface normal, consistent with the conclusion drawn by SERS in the literature.     

Single‐Nanoparticle Collision Events: Tunneling Electron Transfer on a Titanium Dioxide Passivated n‐Silicon Electrode

Single‐nanoparticle collisions were observed on an n‐type silicon electrode (600 μm diameter) passivated by a thin layer of amorphous TiO₂, where the current steps occurred by tunneling electron transfer. The observed collision frequency was in reasonable agreement with that predicted from theory. The isolated electrode, after a collision experiment, with a Pt/TiO₂/n‐Si architecture was shown to retain the photoelectrochemical properties of n‐Si without photocorrosion or current decay. The Pt/TiO₂/n‐Si electrode produced 19 mA cm^?2 of photocurrent density under 100 mW cm^?2 irradiation from a xenon lamp during oxygen evolution without current fading for over 12 h.     

Epitaxy‐like orientation of nanoscale Ag islands grown on air‐oxidized Si(110)‐(5 × 1) surfaces

Growth of Ag islands under ultra‐high vacuum condition on air‐oxidized Si(110)‐(5 × 1) surfaces has been investigated by in situ reflection high energy electron diffraction and ex situ scanning electron microscopy and cross‐sectional transmission electron microscopy. A thin oxide is formed on Si via exposure of the clean Si(110)‐(5 × 1) surface to air. The oxide layer has a short range order. Deposition of Ag at different thicknesses and at different substrate temperatures reveal that the crystalline qualities of the Ag film are almost independent of the thickness of the Ag layer and depend only on the substrate temperature. Ag deposition at room temperature leads to the growth of randomly oriented Ag islands while preferred orientation evolves when Ag is deposited at higher temperatures. For deposition at 550 °C sharp spots in the reflection high energy electron diffraction pattern corresponding to an epitaxial orientation with the underlying Si substrate are observed. The presence of a short range order on the oxidized surface apparently influences the crystallographic orientation of the Ag islands. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis and characterization of Co/CdSe core/shell nanocomposites: bifunctional magnetic-optical nanocrystals

Nanocomposite materials provide the possibility for multifunctional properties in contrast with their more-limited single-component counterparts. Here, we report the synthesis and characterization of the first all-inorganic core/shell hybrid magnetic-optical nanoparticle, cobalt/cadmium selenide. The core/shell nanocrystals are prepared in a facile one-pot reaction, and their microstructure is analyzed using low- and high-resolution transmission electron microscopy. Using magnetic and optical characterization, we demonstrate bifunctional behavior, whereby the core retains the magnetic properties of the starting Co nanoparticle, and the shell emits similarly to a single-component CdSe nanoparticle. Interestingly, while the coercivity was found to be unchanged by shell formation, the blocking temperature for the composite structure was observed to be substantially lower (Co: >350 K; Co/CdSe: 240 K). In addition, we observed that at low temperatures (20 K) shell CdSe photoluminescence (PL) decay was very rapid (<1 ns). In contrast, nanocrystalline CdSe PL decay is typically much slower at such temperatures (>50 ns). Finally, we propose possible explanations for the unusual magnetic and optical behavior of the core/shell hybrid nanostructures.     

Probing of porphyrin surface chemistry in systems with laser-ablated Ag nanoparticle hydrosol: role of thiosulfate anions

The influence of sodium thiosulfate (THS) concentration in Ag colloid/THS/H(2)TMPyP and Ag colloid/H2TMPyP/THS systems (H2TMPyP = 5,10,15,20-tetrakis(1-methyl-4-pyridyl)porphyrin) was investigated by a combination of surface-enhanced resonance Raman scattering (SERRS) spectroscopy, surface plasmon extinction (SPE) measurements, and transmission electron microscopy (TEM). THS was found to have a strong impact on Ag nanoparticle surface structure and aggregation state and on interaction with H2TMPyP probe molecules, as evidenced by variations of the SERRS spectrum. In the Ag colloid/THS/H2TMPyP system, when laser-ablated Ag colloid was THS pretreated prior to the porphyrin addition, a critical threshold THS concentration (4 x 10(-5) M) was discovered. At concentrations below the threshold, THS mainly reduces the number of Ag+ adsorption sites. This leads to increased Ag nanoparticle aggregation prior to the porphyrin addition and significant weakening of the overall SERRS signal. Dominant contributions in the SERRS spectrum correspond to free base H2TMPyP and Ag+ containing the AgTMPyP form. At concentrations above the threshold, THS mediates also the formation and stabilization of new adsorption sites, probably Ag(0) sites. This induces a turn in the aggregation state of the pretreated Ag-c/THS system, an increase of the overall SERRS signal, and the appearance of a new spectral form of Ag metalated porphyrin.     

An Arrayed Micro‐glutamate Sensor Probe Integrated with On‐probe Ag/AgCl Reference and Counter Electrodes

Complete all‐in‐one multi‐arrayed glutamate (Glut) sensors have been constructed on a silicon‐based micromachined probe composed of micro‐platinum (Pt) working electrodes, a micro‐silver/silver chloride (Ag/AgCl) reference electrode (RE), and a micro‐Pt counter electrode (CE). The OCP shift of the electrodeposited Ag/AgCl on‐probe micro‐reference electrode compared with a Ag/AgCl wire is <0.1 mV/h. The composition ratio of Ag, Cl, and Pt on the electrodeposited on‐probe micro‐reference electrode is observed to be 1.00 : 0.48 : 0.02 analyzed by EDS. The miniaturized amperometric Glut biosensors were constructed on working electrode sites (electrode area: ∼8.5×10⁻⁵ cm²) of the microprobe modified with glutamate oxidase (GlutOx) enzyme layers for the selective, fast, and continuous detection of L‐glutamate. The sensor selectivity towards common electroactive interferents has been improved significantly by coating the electrode surface with perm‐selective polymer layers, overoxidized polypyrrole (PPY) and Nafion®. The sensitivity, detection range, and response time of the proposed all‐in‐one Glut biosensors are 204.7±5.8 nA μM⁻¹ cm⁻² (N=5), 4.99–109 μM, and 2.7±0.3 sec, respectively and no interferent signals of AA and DA were observed. The sensor can be reused over 19 times of continuous repetitive operation (total measurement time: ∼4 hours) and the sensor sensitivity can retain up to four weeks of storage.     

The new Micro‐set for Adsorptive Stripping Voltammetric Simultaneous Determination of Nickel and Cobalt Traces in Aqueous Media

This article the first reports on a fabrication and application of an electrochemical three electrode micro‐set containing: in situ plated lead film on carbon fiber working microelectrode, Ag/AgCl reference electrode and a platinum wire counter electrode placed in one casing for simultaneous Ni(II) and Co(II) traces determination by square wave adsorptive stripping voltammetry (SW AdSV). Ni(II) and Co(II) in forms of their complexes with nioxime were accumulated on the lead film plated on a carbon fibers microelectrode during standard procedure of measurement. Thanks to the fact that measurements were performed in micro‐vessel of a volume of 200 μl small amounts of reagents were used to prepare samples for measurements. In addition, because of the use of microelectrode, sample solutions were not mixed during accumulation step of measurements. This fact creates the possibility of conducting fields analysis. The experimental parameters (composition of the supporting electrolyte, potential and time of accumulation) and possible interference effects were investigated. The linear calibration graphs for Ni(II) and Co(II) were in the range from 2×10^?9 to 1×10^?7 mol L^?1 and from 2×10^?10 to 1×10^?8 mol L^?1 for Ni(II) and Co(II), respectively. The correctness of the proposed method was checked by determining Ni(II) and Co(II) in the certified reference material (SPS‐SW1) with satisfactory results.     

The effect of magnetic fields on the electrodeposition of iron

The effect of a uniform magnetic field with flux density up to 1 T on the electrodeposition of Fe from sulphate electrolyte has been investigated under different field configurations relative to the electrode surface. Voltammetric and chronoamperometric experiments have been carried out coupled with an electrochemical quartz crystal microbalance for in situ mass change measurements. The structure and morphology of the deposited films were determined by scanning electron microscopy, atomic force microscopy and X-ray diffraction measurements. Results show that, when the magnetic field is applied parallel to the electrode surface, the limiting current density and the deposition rate are increased due to the magnetohydrodynamic effect. The nucleation process is also affected in parallel configuration; the current density of the maximum on the chronoamperograms is decreased, and an additional nucleation step might be observed. This effect is attributed to the hydrodynamic response of the electrochemical system. No significant influence on the electrochemical reaction was observed when a magnetic field was applied perpendicular to the electrode. But in this configuration, the morphology of deposited layers is changed by the magnetic field. The morphology changes are discussed. No effect of the magnetic field on the crystallographic structure was observed.     

A general method for the rapid synthesis of hollow metallic or bimetallic nanoelectrocatalysts with urchinlike morphology

We have reported a facile and general method for the rapid synthesis of hollow nanostructures with urchinlike morphology. In-situ produced Ag nanoparticles can be used as sacrificial templates to rapidly synthesize diverse hollow urchinlike metallic or bimetallic (such as Au/Pt) nanostructures. It has been found that heating the solution at 100 degrees C during the galvanic replacement is very necessary for obtaining urchinlike nanostructures. Through changing the molar ratios of Ag to Pt, the wall thickness of hollow nanospheres can be easily controlled; through changing the diameter of Ag nanoparticles, the size of cavity of hollow nanospheres can be facilely controlled; through changing the morphologies of Ag nanostructures from nanoparticle to nanowire, hollow Pt nanotubes can be easily designed. This one-pot approach can be extended to synthesize other hollow nanospheres such as Pd, Pd/Pt, Au/Pd, and Au/Pt. The features of this technique are that it is facile, quick, economical, and versatile. Most importantly, the hollow bimetallic nanospheres (Au/Pt and Pd/Pt) obtained here exhibit an area of greater electrochemical activity than other Pt hollow or solid nanospheres. In addition, the approximately 6 nm hollow urchinlike Pt nanospheres can achieve a potential of up to 0.57 V for oxygen reduction, which is about 200 mV more positive than that obtained by using a approximately 6 nm Pt nanoparticle modified glassy carbon (GC) electrode. Rotating ring-disk electrode (RRDE) voltammetry demonstrates that approximately 6 nm hollow Pt nanospheres can catalyze an almost four-electron reduction of O(2) to H(2)O in air-saturated H(2)SO(4) (0.5 M). Finally, compared to the approximately 6 nm Pt nanoparticle catalyst, the approximately 6 nm hollow urchinlike Pt nanosphere catalyst exhibits a superior electrocatalytic activity toward the methanol oxidation reaction at the same Pt loadings.     

Investigation of the effect of forming gas annealing on front silver electrodes of c‐Si solar cells

Forming gas annealing (FGA) is an effective process to repair low efficiency crystalline silicon (c‐Si) solar cells with overfired screen‐printed paste electrodes. An experimental study was performed to investigate the effect and mechanism of FGA treatment on front silver electrodes of c‐Si cells. To facilitate the FGA mechanistic study, special simulation samples were prepared to magnify the FGA effects on glass frit and overfired electrodes. The micro‐morphology (from cross‐sectional X‐SEM) and elemental composition (from energy‐dispersive X‐ray spectroscopy) data revealed few Ag crystallites in the paste/Si interface because of the thick glass layer from the paste overfiring. The FGA treatment induced phase crystallization (from X‐ray diffraction) in the paste and increased the glass wettability on both Si and Ag substrates, thus resulting in a thinner glass layer, which expedited the precipitation of more pyramidal Ag crystallites at the Ag/Si interface. The wetting angle data of glass samples measured before and after FGA confirmed the mechanism of FGA and concluded that the improvement of glass wettability benefited to reduce the glass layer thickness. As a result, more Ag crystallites diffused toward and precipitated at the Si interface contributing to a lower contact resistance between the paste electrode and the Si matrix and thus improved electrical properties for overfired c‐Si cells. Copyright © 2012 John Wiley & Sons, Ltd.     

Synthesis of gradient polymer by using polysiloxane‐based photoinitiator

This paper reported a polysiloxane‐based photoinitiator (184‐AC‐Si), which was synthesized basing on traditional photoinitiator 1‐hydroxy‐cyclohexyl phenyl ketene (184) and polysiloxane. Its structure was confirmed by Hydrogen‐1 nuclear magnetic resonance (¹H NMR), real‐time infrared spectroscopy and gel permeation chromatography (GPC). Ultraviolet (UV) absorption spectra of 184‐AC‐Si showed a red‐shifted maximum absorption compared with 184. The kinetics of photopolymerization was studied by real‐time infrared spectroscopy. More importantly, because of the polysiloxane‐based photoinitiator had good ability to float up, which could be proved by X‐ray photoelectron spectroscopy, mapping energy dispersive spectroscopy, UV absorption, and GPC measurements, a convenient and simple method for preparing gradient polymer initiated by 184‐AC‐Si was successfully developed. Copyright © 2011 John Wiley & Sons, Ltd.     

Quantized Double‐Layer Charging of Iron Oxide Nanoparticles on a‐Si:H Controlled by Charged Defects in a‐Si:H

Sequential single‐electron charging of iron oxide nanoparticles encapsulated in oleic acid/oleyl amine envelope and deposited by the Langmuir‐Blodgett technique onto Pt electrode covered with undoped hydrogenated amorphous silicon film (a‐Si:H) is reported. Quantized double‐layer charging of nanoparticles is detected by cyclic voltammetry as current peaks and the charging effect can be switched on/off by the excess of negative/positive charged defect states in the a‐Si:H layer. The particular charge states in a‐Si:H are created by the simultaneous application of a suitable bias voltage and illumination before the measurement.     

Electrochemical stripping detection of DNA hybridization based on cadmium sulfide nanoparticle tags

We report on the detection of DNA hybridization in connection to cadmium sulfide nanoparticle tracers and electrochemical stripping measurements of the cadmium. A nanoparticle-promoted cadmium precipitation is used to enlarge the nanoparticle tag and amplify the stripping DNA hybridization signal. In addition to measurements of the dissolved cadmium ion we demonstrate solid-state measurements following a ‘magnetic’ collection of the magnetic-bead/DNA-hybrid/CdS-tracer assembly onto a thick-film electrode transducer. The new protocol combines the amplification features of nanoparticle/polynucleotides assemblies and highly sensitive stripping potentiometric detection of cadmium, with an effective magnetic isolation of the duplex. The low detection limit (100 fmol) is coupled to good reproducibility (RSD=6%). Prospects for using binary inorganic colloids for multi-target detection are discussed.     

Anisotropic magnetoresistance and piezoresistivity in structured Fe3O4-silver particles in PDMS elastomers at room temperature

Magnetorheological elastomers, MREs, based on elastic organic matrices displaying anisotropic magnetoresistance and piezoresistivity at room temperature were prepared and characterized. These materials are dispersions of superparamagnetic magnetite forming cores of aggregated nanoparticles inside silver microparticles that are dispersed in an elastomeric polymer (poly(dimethylsiloxane), PDMS), curing the polymer in the presence of a uniform magnetic field. In this way, the elastic material becomes structured as the application of the field induces the formation of filaments of silver-covered inorganic material agglomerates (needles) aligned in the direction of the field (parallel to the field). Because the magnetic particles are covered with silver, the MREs are not only magnetic but also electrical conductors. The structuration induces elastic, magnetic, and electrical anisotropic properties. For example, with a low concentration of particles in the elastic matrix (5% w/w) it is possible to obtain resistances of a few ohms when measured parallel to the needles or several megaohms in the perpendicular direction. Magnetite nanoparticles (Fe(3)O(4) NP) were synthesized by the coprecipitation method, and then agglomerations of these NPs were covered with Ag. The average size of the obtained magnetite NPs was about 13 nm, and the magnetite-silver particles, referred to as Fe(3)O(4)@Ag, form micrometric aggregates (1.3 μm). Nanoparticles, microparticles, and the MREs were characterized by XRD, TEM, SEM, EDS, diffuse reflectance, voltammetry, VSM, and SQUID. At room temperature, the synthesized magnetite and Fe(3)O(4)@Ag particles are in a superparamagnetic state (T(B) = 205 and 179 K at 0.01 T as determined by SQUID). The elastic properties and Young's modulus of the MREs were measured as a function of the orientation using a texture analysis device. The magnetic anisotropy in the MRE composite was investigated by FMR. The electrical conductivity of the MRE (σ) increases exponentially when a pressure, P, is applied, and the magnitude of the change strongly depends on what direction P is exerted (anisotropic piezoresistivity). In addition, at a fixed pressure, σ increases exponentially in the presence of an external magnetic field (H) only when the field H is applied in the collinear direction with respect to the electrical flux, J. Excellent fits of the experimental data σ versus H and P were achieved using a model that considers the intergrain electron transport where an H-dependent barrier was considered in addition to the intrinsic intergrain resistance in a percolation process. The H-dependent barrier decreases with the applied field, which is attributed to the increasing match of spin-polarization in the silver covers between grains. The effect is anisotropic (i.e., the sensitivity of the magnetoresistive effect is dependent on the relative orientation between H and the current flow J). In the case of Fe(3)O(4)@ Ag, when H and J are parallel to the needles in the PDMS matrix, we obtain changes in σ up to 50% for fields of 400 mT and with resistances on the order of 1-10 Ω. Magnetoresistive and magnetoelastic properties make these materials very interesting for applications in flexible electronics, electronic skins, anisotropic pressure, and magnetic field sensors.     

Ethane‐Bridged Periodic Mesoporous Organosilicas Functionalized with High Loadings of Carboxylic Acid Groups: Synthesis,Bifunctionalization, and Fabrication of Metal Nanoparticles

Well‐ordered periodic mesoporous organosilicas (PMOs) functionalized with high contents of carboxylic acid (?COOH) groups, up to 85 mol % based on silica, were synthesized by co‐condensation of 1,2‐bis(triethoxysilyl)ethane (BTEE) and carboxyethylsilanetriol sodium salt (CES) under acidic conditions by using alkyl poly(oxyethylene) surfactant Brij 76 as a structure‐directing agent. A variety of techniques including powder X‐ray diffraction (XRD), nitrogen adsorption/desorption, Fourier‐transformed infrared (FTIR), transmission electron microscopy (TEM), ¹³C‐ and ²⁹Si solid‐state nuclear magnetic resonance (NMR) were used to characterize the products. The materials thus obtained were used as an effective support to synthesize metal nanoparticles (Ag and Pt) within the channel of 2D hexagonal mesostructure of PMOs. The size and distribution of the nanoparticles were observed to be highly dependent on the interaction between the carboxylic acid functionalized group and the metal precursors. The size of Pt nanoparticles reduced from 3.6 to 2.5 nm and that of Ag nanoparticles reduced from 5.3 to 3.4 nm with the increase in the ?COOH loading from 10 to 50 %.     

Reversible adsorption change of 2‐amino‐4,5‐imidazoledicarbonitrile on Ag electrode surfaces by potential‐dependent surface‐enhanced Raman scattering

The potential‐induced adsorption change of 2‐amino‐4,5‐imidazoledicarbonitrile (AIDCN) on Ag electrode surfaces has been examined by surface‐enhanced Raman scattering (SERS) in an applied potential range between ?1.0 and 0.2 V. Upon adsorption, AIDCN has a substantial interaction with the Ag metal surfaces via its two nitrile groups. The CN stretching peaks at ～2200 cm^?1 appeared to be more intensified and redshifted at a negative potential. The deconvolution peak analysis of the CN bands at various voltages suggests that there should be a change in binding modes of AIDCN on Ag surfaces. This potential‐dependent orientation change appeared to be reversible. The density functional theory (DFT) calculation of AIDCN on Ag cluster atoms is used to explain its potential‐dependent adsorption. Copyright © 2010 John Wiley & Sons, Ltd.     

N‐Doped Sub‐3 nm Co Nanoparticles as Highly Efficient and Durable Aerobic Oxidative Coupling Catalysts

A nano‐coating associated with sulfuric acid leaching protocol was developed to prepare N‐doped sub‐3 nm Co‐based nanoparticle catalyst (Co?N/C) using melamine–formaldehyde resin as the N‐containing precursor, active carbon as the support, and Co(NO₃)₂ as the Co‐containing precursor. By thermal treatment under nitrogen atmosphere at 800 °C and leached with sulfuric acid solution, a stable and highly dispersive Co?N coordination structure was uniformly dispersed on the formed Co?N/C catalyst with a Co loading of 0.47 wt % and Co nanoparticle size of 2.55 nm. The Co?N/C catalyst was characterized with XRD, XPS, Raman, SEM, TEM, ICP, and elemental analysis. The Co?N/C catalyst showed extremely high catalytic efficiency with a TON of 257 for the aerobic oxidative coupling of aldehydes with methanol to directly synthesize methyl esters with molecular oxygen as the final oxidant. The Co?N/C catalyst also showed broad substrate range and stable recyclability. After recycling for 7 times, no obvious deactivation was detected. It was confirmed that the sub‐3 nm Co?N coordination structure formed between metallic Co nanoparticles and pyridinic nitrogen doping into graphitic layers functions as the active site to activate molecular oxygen for the β‐H elimination from generated hemiacetal intermediates to produce methyl esters. The nano‐coating associated with acid leaching protocol provides a novel strategy to prepare highly efficient non‐precious metal‐based catalysts.     

银纳米颗粒的合成及用于抗癌药氟他胺的电化学检测（英文）

Ag nanoparticles were synthesized on the surface of a glassy carbon electrode modified with p‐tert‐butylcalix[4]arene and p‐tert‐butylcalix[6]arene by the deposition of Ag+ at an open circuit potential followed by the electrochemical reduction of the Ag+.The presence of the calixarene layer on the electrode surface controlled the particle size and prevented agglomeration.Cyclic voltam‐metry showed that the Ag nanoparticles on the modified glassy carbon electrode had good catalytic ability for the reduction of flutamide.The effects of calixarene concentration,potential applied for the reduction of Ag+,number of calixarene layers,and p H value on the electrocatalytic activity of the Ag nanoparticles were investigated.The modified electrode had a linear range in differential pulse voltammetry of 10-1000 μmol/L with a detection limit of 9.33 μmol/L for flutamide at an S/N = 3.The method was applied to the detection of flutamide in practical samples.     

Ag(I)与Co(II)离子对阳极析氧过程的电催化作用

Influence of Ag(Ⅰ), Co(Ⅱ) and Ni(Ⅱ) ions on oxygen anodic evolution at Pt and Ti/Pt/PbO2 electrodes was investigated in surphuric acid solutions. The oxygen evolution reaction at Ti/Pt/PbO2 electrode in surphuric acid solutions is characterized by two linearφ~ lgi relationships. At low c.d. it is close to 2.303RT/(1+β)F, whereas at high c.d. it is close to 2.303RT/βF. In the presence of Ag(Ⅰ) or Ni(Ⅱ) ions in the electrolytic solution the Tafel slope of oxygen evolution tends to be low, 2.303RT/(1+β)F (withβ=0.5). However, the oxygen evolution reaction at Pt electrodes in H2SO4 or CoSO4﹢H2SO4 solutions is characterized by one linearφ~ lgi relationship. The Tafel slope is close to 2.303RT/βF. In the presence of Ag(Ⅰ) or Ni(Ⅱ) ions in the electrolytic solution the Tafel slope of oxygen evolution tends to be low, 2.303RT/(1+β)F. The oxygen anodic evolution reactions are catalyzed by Ag(Ⅰ), Co(Ⅱ) and Ni(Ⅱ) ions in the electrolytic solution. When Ag(Ⅰ) or Ni(Ⅱ) was mixed with Co(Ⅱ), a promising catalyst for oxygen anodic evolution with higher catalyst activity than either of them alone was found. A comparison of the PbO2 electrode and the Pt electrode has also been given.     

Green Synthesis of Silver Nanoparticles Using Ionic Liquid and Application for the Detection of Dissolved Oxygen

The electrochemical synthesis of silver nanoparticles (nano‐Ag) has been successfully carried out on glassy carbon electrode (GCE) and indium tin oxide electrode (ITO) using 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMT) as green electrolytes. Further the electrodeposited nano‐Ag modified ITO electrode has been examined using atomic force microscopy (AFM), and X‐ray diffraction studies (XRD). The electrodeposited Ag nanoparticles on ITO were found in the size range of 5 to 35 nm. The nano‐Ag film modified GCE was further coated with nafion (Nf) and BMT (1 : 1 ratio) mixture and found to be stable in BMT and in pH 7 phosphate buffer solution (PBS). The nano‐Ag/BMT‐Nf film modified GCE successfully applied for the oxygen reduction reaction in neutral pH (pH 7.0 PBS). The proposed film modified GCE successfully reduces the over potential and show well defined reduction peaks for the detection of dissolved oxygen using cyclic voltammetry (CV) and rotating disc voltammetry (RDE). The film also applied for the detection of dissolved oxygen using electrochemical impedance spectroscopic studies (EIS).