镁铜合金储氢材料的制备及对高氯酸铵热分解过程的影响

采用置换-扩散法制备了镁铜合金储氢材料(Mg2Cu-H), 并对其结构进行了表征. 结果表明, Mg2Cu经过氢化得到的镁铜合金储氢材料不是单一晶相, 而是MgCu2和MgH2的混合物. 用热分析法(DSC)研究了镁铜合金储氢材料对固体火箭推进剂常用氧化剂——高氯酸铵(AP)热分解过程的影响. 结果表明, 镁铜合金储氢材料可以显著促进AP的热分解过程, 加快热分解速率, 降低高温热分解温度, 使DSC表观分解热明显增大. Mg2Cu-H对AP热分解过程的促进作用明显强于Mg2Cu. 随着加入量增加, 镁铜合金储氢材料对AP热分解的催化促进作用增强. 探讨了镁铜合金储氢材料促进AP热分解过程的作用机制.     

纳米NdCoO3催化高氯酸铵热分解的DSC/TG-MS研究

采用微乳液法制备了立方晶系的NdCoO3纳米晶.利用DSC/TG-MS研究了NdCoO3对AP热分解的催化作用.结果表明,在NdCoO3的催化作用下,AP的热分解反应峰值温度下降了113℃,表观分解反应热从655 J·g-1增加到1 363 J·g-1,分解的气相产物主要有NH3,H2O,O2,HCl,N2O,NO,NO2和Cl2.在金属氧化物表面吸附生成超氧化离子(O2-)和氧离子(O-,O2-),这是加速AP分解反应的主要原因.加入NdCoO3催化AP热分解,由于对氨的氧化深度不同而导致分解放热量的增加.     

干燥方式对高氯酸铵/石墨烯复合材料的结构和热分解行为的影响

通过溶胶-凝胶法制备了石墨烯水凝胶, 并将其与高氯酸铵(AP)复合, 然后分别采用自然干燥、冷冻干燥和超临界CO₂干燥三种干燥方式制备了AP/石墨烯复合材料, 并通过扫描电镜(SEM)、元素分析、X射线衍射(XRD)、差示扫描量热仪(DSC)和热重-红外联用技术(TG-FTIR)研究了不同干燥方式对其结构和热分解行为的影响. 结果表明, 干燥方式对AP/石墨烯复合材料的形貌具有明显影响, 其中通过超临界CO₂干燥制备的AP/石墨烯复合材料基本能保持与石墨烯气凝胶相似的外观和多孔结构. 通过自然干燥、冷冻干燥和超临界CO₂干燥制备的AP/石墨烯复合材料中AP的质量分数分别为89.97%、92.41%和94.40%, 其中通过超临界CO₂干燥制备的复合材料中AP的粒径尺寸为69 nm. DSC测试结果表明, 石墨烯对AP的热分解过程具有明显的促进作用, 能使AP的低温分解过程大大减弱, 高温分解峰温明显降低. 三种干燥方式相比, 通过超临界CO₂干燥制备的AP/石墨烯复合材料中石墨烯的促进作用最明显. 与纯AP相比, 其高温分解峰温降低了83.7℃, 表观分解热提高到2110 J·g^-1. TG-FTIR分析结果表明, AP/石墨烯复合材料的热分解过程中, AP分解产生的氧化性产物与石墨烯发生了氧化反应, 生成了CO₂.     

含能钴配合物的催化燃烧性能研究

水热条件下合成了一个四唑含能配合物[Co(pzta)(H_2O)_2](pzta=5-吡嗪基四唑)。运用TG-DSC热分析仪研究了配合物的热分解行为;在非等温条件下,采用Kissinger's和Ozawa-Doyle's两种方法,对配合物进行了非等温动力学研究,得到它的表观活化能(E=153.63 k J mol-1)。利用DSC技术分析了配合物对AP和HMX热分解行为的影响,结果表明:配合物的加入对于HMX的放出的热量和峰温影响不大;使AP的分解峰温提前不多,但是加入配合物后呈现出的剧烈放热过程,放热量增加,因此配合物对AP具有较好的催化燃烧效果。     

多孔纳米CoFe2O4的制备及其对高氯酸铵的热分解催化性能

采用胶晶模板法制备出具有三维多孔结构的纳米CoFe₂O₄。利用X射线衍射仪(XRD)、傅里叶变换红外(FT-IR)光谱仪、扫描电镜(SEM)、透射电镜(TEM)和N₂吸附-脱附对样品的晶型和形貌结构等进行表征,采用差示扫描量热法(DSC)对比研究多孔纳米CoFe₂O₄和球形纳米CoFe₂O₄对高氯酸铵(AP)的热分解性能的影响,并考察这两种催化剂对AP催化热分解的动力学参数。结果显示,制备出的多孔纳米CoFe₂O₄样品具有典型的尖晶石结构,孔径约200 nm;比表面积明显高于40 nm球形CoFe₂O₄,达到55.646 m²·g^-1。DSC测试结果表明：多孔纳米CoFe₂O₄的加入促进了AP的热分解,最高使AP的高温分解峰温降低91.46℃,能量释放最高达1120.88 J·g^-1,是纯AP分解放热量的2.3倍;多孔纳米CoFe₂O₄具有较高的比表面积,能提高催化反应的接触面积,使AP的高温分解峰温度更低,反应活化能较小,从而表现出比球形纳米CoFe₂O₄更高的催化活性。此外,对多孔纳米CoFe₂O₄催化AP的热分解机理进行初步探索,纳米多孔催化剂对气态中间产物的作用促进了AP的热分解。     

纳米Co-B非晶态合金对高氯酸铵分解的催化性能

 利用化学还原法制备了纳米 Co-B 非晶态合金,并用透射电镜、X射线衍射、差示扫描量热和N2吸附表面积测试等技术对样品进行了表征. 运用差热分析研究了纳米 Co-B 非晶态合金对高氯酸铵(AP)分解的催化性能. 结果表明,加入 Co-B 非晶态合金后AP的高低温放热峰相连,合并成一个高而大的放热峰,且峰温有很大程度的降低, 这说明纳米 Co-B 非晶态合金对AP热分解有很好的催化活性. 同时, Co-B 非晶态合金能使AP的表观分解热显著增大.     

化学计量比和放氢背压对LiBH4+xMg2NiH4体系放氢性能的影响

研究了不同化学计量比(x=0.25, 0.5, 0.75, 1.0, 1.25)和放氢背压(1×10-4和0.4 MPa)对LiBH4+xMg2NiH4复合体系吸放氢性能的影响. 结果表明, 随着化学计量比(x)的增加, 复合体系的放氢温度逐渐降低, 放氢动力学性能得到提高, 但放氢容量逐渐降低; 其中, 在1×10-4和0.4 MPa初始放氢背压下, LiBH4+0.75Mg2NiH4体系具有最佳放氢动力学性能和较高的储氢容量. 结果表明, 放氢背压和化学计量比均会对高温下液相LiBH4 与固态Mg2NiH4 的润湿性产生影响, 进而影响复合体系的放氢路径和放氢动力学性能.     

纳米Fe2O3/高氯酸铵复合粒子的制备及其热分解性能研究

用溶剂-非溶剂法制备了纳米Fe2O3／高氯酸铵(AP)复合粒子，并用TEM，SEM，XRD和ICP对其进行了表征．为了研究纳米复合粒子中纳米Fe2O3对AP热分解的催化性能，将相同比例的微米Fe2O3和纳米Fe2O3与AP分别简单混合后作对比，并用DTA对三种样品进行了热分析．结果表明，三种样品中的Fe2O3粒子都能催化AP的热分解；但纳米Fe2O3粒子的催化性能优于微米Fe2O3粒子，纳米Fe2O3／AP复合粒子中纳米Fe2O3对AP的催化性能优于纳米Fe2O3与AP简单混合物．与纳米Fe2O3与AP简单混合的样品相比，纳米复合粒子中的AP高温分解峰温降低20．1℃，低温分解峰几乎消失，表观分解热由850．2J／g提高到1080．8J／g．证明纳米Fe2O3与AP的复合处理能显著提高纳米Fe2O3对AP热分解的催化性能．并用不同样品中AP热分解的动力学参数对所得结果进行了理论分析．     

两个2,6-二氨基-3,5-二硝基吡嗪-1-氧化物含能配合物的合成、晶体结构及催化性能(英文)

合成了2,6-二氨基-3,5-二硝基吡嗪-1-氧化物(LLM-105)2种含能配合物[Cu4O2(C4N6O5H2)2(CH3COO)2(DMF)2]·DMF(1)((C4N6O5H2)2-为配体LLM-105失去2个H+)和[Co(C4N6O5H3)3]·7H2O(2)((C4N6O5H3)-为LLM-105失去1个H+),用X射线单晶衍射法测定了其分子结构。配合物1属正交晶系,空间群为Pbca,配合物2属三斜晶系,空间群为R3。用DSC,TG-DTG技术对配体和2个配合物的热分解进行了研究。用Kissinger法和Ozawa-Doyle法对配合物热分解过程中放热峰的表观活化能进行了计算。同时研究了2种配合物对AP热分解催化效果的影响,结果表明,2种配合物使AP的高温分解峰温分别提前117.42和71.85℃,分解放热量增加1 916.97和1 433.76 J·g-1,对AP热分解具有非常显著的催化效果。     

La-H化合物对LaMg2Ni合金中Mg2Ni相吸氢过程的影响

采用感应熔炼技术在Ar气氛保护下制备得到LaMg2Ni与Mg2Ni合金。X射线衍射(XRD)图表明LaMg2Ni合金在吸氢过程中分解为LaH3相和Mg2NiH4相,放氢过程中LaH3相转化为La3H7相。与Mg2Ni合金相比,LaMg2Ni合金显示出优良的吸氢动力学性能,这是由于镧氢化合物的存在及其在吸氢过程中所发生的相转变所造成的。LaMg2Ni合金280 s内吸氢即可达到最大储氢量的90%以上,而Mg2Ni合金则需要1200 s才能达到,且在相同温度下LaMg2Ni合金的吸氢反应速率常数大于Mg2Ni合金速率常数。镧氢化合物不仅有利于改善动力学性能,而且可以提高热力学性能。LaMg2Ni合金中的Mg2Ni相氢化反应焓与熵分别为-53.02 kJ.mol-1和84.96 J.K-1.mol-1(H2),这一数值小于单相Mg2Ni氢化反应焓与熵(-64.50 kJ.mol-1,-123.10 J.K-1.mol-1(H2))。压力-组成-温度(P-C-T)测试结果表明在603 K至523 K温度范围内,LaMg2Ni合金储氢容量保持稳定为1.95wt%左右,然而Mg2Ni合金的储氢容量则由4.09wt%衰减为3.13wt%,Mg2Ni合金的储氢容量在523K低温下仅为603 K时的76.5%,表明镧氢化合物能够改善Mg2Ni合金低温下的吸放氢性能。     

Pure CuCr2O4 nanoparticles: Synthesis,characterization and their morphological and size effects on the catalytic thermal decomposition of ammonium perchlorate

In the present paper a pure phase of the copper chromite spinel nanoparticles (CuCr₂O₄ SNPs) were synthesized via the sol–gel route using citric acid as a complexing agent. Then, the CuCr₂O₄ SNPs has been characterized by field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). In the next step, with the addition of Cu–Cr–O nanoparticles (NPs), the effects of different parameters such as Cu–Cr–O particle size and the Cu/Cr molar ratios on the thermal behavior of Cu–Cr–O NPs + AP (ammonium perchlorate) mixtures were investigated. As such, the catalytic effect of the Cu–Cr–O NPs for thermal decomposition of AP was evaluated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA/DSC results showed that the samples with different morphologies exhibited different catalytic activity in different stages of thermal decomposition of AP. Also, in the presence of Cu–Cr–O nanocatalysts, all of the exothermic peaks of AP shifted to a lower temperature, indicating the thermal decomposition of AP was enhanced. Moreover, the heat released (ΔH) in the presence of Cu–Cr–O nanocatalysts was increased to 1490 J g⁻¹.     

Effect of catocene on the thermal decomposition of ammonium perchlorate and octogen

Simultaneous TG/DSC-FT-IR was employed to study the effect of catocene with a high concentration (5, 15, and 25 %) on the thermal decomposition of ammonium perchlorate (AP) and octogen (HMX) with different particle sizes. The experimental results show that catocene has effect on the thermal decomposition of AP and HMX, but the role that catocene playing changes with the concentration of catocene and the particle size of AP and HMX. High concentration of catocene (more than 15 %) benefits the decomposition of fine AP and HMX at low temperature, but has little effect on the decomposition of median and coarse AP. The thermal decomposition of HMX is affected by catocene mainly through increasing the heat release of the first decomposition step, while through both increasing the heat release and decreasing the decomposition temperature of the first decomposition step for the thermal decomposition of AP.     

Preparation of NdCrO3 nanoparticles and their catalytic activity in the thermal decomposition of ammonium perchlorate by DSC/TG-MS

Orthorhombic structural perovskite NdCrO₃ nanocrystals with size of 60 nm were prepared by microemulsion method, and characterized by XRD, TEM, HRTEM, SEM, EDS and BET. The catalytic effect of the NdCrO₃ for thermal decomposition of ammonium perchlorate (AP) was investigated by DSC and TG-MS. The results revealed that the NdCrO₃ nanoparticles had effective catalysis on the thermal decomposition of AP. Adding 2% of NdCrO₃ nanoparticles to AP decreased the temperature of thermal decomposition by 87° and increased the heat of decomposition from 590 to 1073 J g⁻¹. Gaseous products of thermal decomposition of AP were NH₃, H₂O, O₂, HCl, N₂O, NO, NO₂ and Cl₂. The mechanism of catalytic action was based on the presence of superoxide ion O₂ ⁻ on the surface of NdCrO₃, and the difference of thermal decomposition of AP with 2% of NdCrO₃ and pure AP was mainly caused by the different extent of oxidation of ammonium.     

Al 掺杂对Mg2Ni 合金的电子结构及贮氢性能的影响

采用基于密度泛函理论(DFT)的平面波赝势(PW-PP)方法, 计算Mg_2-xAl_xNiH₄ (x=0, 0.125, 0.25)合金的晶胞体积、电子态密度、键序、电荷布居、生成焓, 分析原子间成键和结构的稳定性, 研究Al 部分替代Mg 对Mg₂Ni 合金及其氢化物的结构和储氢性能的影响. 结果表明: 随着Al 含量的增加, Mg₂Ni 合金晶胞体积减小, 不利于氢原子进入合金中, 导致合金的储氢容量降低. 在Mg_2-xAl_xNiH₄ (x=0, 0.125, 0.25)中, Mg-H和Al-H相互作用远小于Ni-H的相互作用, 随着Al 含量的增加, 氢化物生成焓减少以及Ni-H的相互作用减弱, 氢化物的结构稳定性降低, Al 部分替代Mg能有效改善Mg₂Ni 合金释氢动力学性能.     

Enhanced Thermal Decomposition Properties and Catalytic Mechanism of Ammonium Perchlorate over CuO/MoS2 Composite

In this report, CuO/MoS₂ composites were successfully prepared by the hydrothermal method where nano‐sized CuO was uniformly distributed on the surface of hierarchical MoS₂ substrates (CuO/MoS₂ composites). Their physicochemical properties and catalytic performance in ammonium perchlorate (AP) decomposition were investigated and characterized by XRD, SEM, TEM, BET, XPS, TG/DSC and combustion measurement. The results showed that it could decrease AP decomposition temperature at high decomposition stage from 416.5 °C to 323.5 °C and increase the heat release from 378 J/g (pure AP) to 1340 J/g (AP with catalysts), which was better than pure CuO nanoparticles (345.5 °C and 1046 J/g). Meanwhile, it showed excellent performance in combustion reaction either in N₂ or air atmosphere. The results obtained by photocurrent spectra, photoluminescence spectra and time‐resolved fluorescence emission spectra indicated that loading CuO mediated the generation rate and combination rate of electrons and holes, thus tuning the catalytic performance on AP decomposition. This study proved that employing the supports that can synergistically interact with CuO is an efficient strategy to enhance the catalytic performance of CuO.