氧化还原低温引发MMA/BA超浓乳液薄层共聚合的研究

以甲基丙烯酸甲酯-丙烯酸丁酯(MMA-BA)作为混合单体、以乳化剂十二烷基硫酸钠(SDS)和共乳化剂十六烷醇(CA)作为复合乳化剂体系、聚乙烯醇(PVA)为液膜增强剂,制备了稳定的超浓乳液.以过氧化二苯甲酰(BPO)和N,N′-二甲基苯胺(DMA)为氧化还原引发体系,用一种新的超浓乳液薄层技术,在较低温度下引发共聚合.探讨了液膜增强剂种类和聚合环境对聚合稳定性影响;研究了薄层厚度,薄层面积,聚合温度和加热方式对体系(包括单体和水)挥发性和转化率的影响.比较了薄层和试管聚合的速率.用透射电子显微镜观察了水浴与烘箱加热方式下聚合物乳胶粒的形态,得到了在水浴中反应后的聚合物粒子平均粒径和分散度都减小的结果.     

PU-St超浓乳液聚合动力学及聚合物性质的研究

采用一步法制备聚氨酯预聚体 ( PU)苯乙烯 ( St)超浓乳液 ,探讨了稳定的超浓乳液的 NCO/OH和 St/PU最佳比例范围。研究了乳化剂和引发剂浓度对超浓乳液聚合的稳定性及聚合动力学的影响 ,并制得了用 PU改性的聚苯乙烯 ( PS)粉状树脂。测定了乳胶粒子大小、粒径分布、分子量和聚合物膜的动态力学性质。发现乳胶粒子大小及其单分散性随聚合转化率的增加而增加 ;与本体聚合比较 ,聚合物的分子量有明显增大 ;PU- PS复合聚合物具有优良性能。     

苯乙烯—甲基丙烯酸超浓乳液的制备及聚合

超浓乳液聚合有着良好的应用前景［１，２］．但文献报道的超浓乳液研究多集中于苯乙烯体系，而对于在此基础上引入功能基单体制备超浓乳液，研究得较少［３］．本文研究了影响苯乙烯（Ｓｔ）与甲基丙烯酸（ＭＡＡ）制备（Ｓｔ－ＭＡＡ）超浓乳液稳定性的因素．探讨了其聚...     

反相乳液共聚合制备两性丙烯酰胺共聚物的研究

采用Span80-Tween80复合乳化剂和AIBA引发剂,进行丙烯酸钠(NaAA)/丙烯酰胺(AM)/丙烯酰氧基乙基三甲基氯化铵(DAC)反相乳液共聚合.研究了聚合温度、引发剂用量、单体浓度、共聚单体中DAC和AM含量、乳化剂用量及其HLB值、水/油比和水相pH值等聚合反应工艺条件或参数对聚合反应单体转化率和聚合物特性粘度的影响,聚合物特性粘度随引发剂用量和单体浓度的增大而增大的实验结果证实了该两性丙烯酰胺共聚物反相乳液制备过程中凝胶效应的存在.傅立叶红外光谱组成分析表明了两性丙烯酰胺共聚物的成功合成,扫描电镜观测乳胶粒粒径范围在0.6~8.0μm.     

具有疏水核/亲水壳的双亲胶体粒子的制备

制备了具有疏水性聚苯乙烯核/亲水性聚丙烯酰胺壳的双亲粒子.疏水核通过超浓乳液聚合制备,亲水壳层通过过氧化羟基异丙苯和硫酸亚铁的界面引发制备.控制条件可得到网孔(半包覆)、褶皱(全包覆)两种形态的壳层.壳层孔的存在使得核层聚合物能够与外界接触.粒子的双亲性通过吸水吸油率进行表征.     

浓乳液双相聚合方法制备异形聚合物粒子

采用浓乳液双相聚合方法,成功制备了聚丙烯酸丁酯(PBA)的异形粒子,通过在连续相中引入聚合物隔层,大大提高了浓乳液聚合过程中的稳定性,探讨了隔层种类对浓乳液稳定性的影响,并研究了浓乳液分散相体积分数和交联剂用量对PBA粒子异形程度的影响,并结果表明,浓乳液双相聚合过程中,分散相体积分数越高,交联剂用量越高,PBA粒子的异形程度越大。     

反相浓乳液方法制备聚苯乙烯/二乙烯基苯结构型泡孔聚合物

通过反相浓乳液聚合方法制备了系列聚苯乙烯/二乙烯基苯(PS/DVB)泡孔聚合物.水作为分散相,其分散相体积分数可达90%;苯乙烯单体作为连续相,聚合后构成PS/DVB泡孔聚合物的结构骨架.用扫描电镜系统研究了乳化剂的浓度、分散相体积分数、添加不同沸点的溶剂等对泡孔聚合物断面形态的影响,并考察了泡孔聚合物对水和柴油的吸附情况.结果表明,不同工艺条件下可以制备出不同孔径的泡孔聚合物,加入不同沸点溶剂使得泡孔壁也形成了多孔结构.     

氧化-还原低温引发甲基丙烯酸甲酯/丙烯酸丁酯超浓乳液聚合研究

以乳化剂十二烷基硫酸钠 (SDS)和共乳化剂十六烷醇 (HD)作为复合乳化体系 ,过氧化二苯甲酰(BPO)和N ,N 二甲基苯胺 (DMA)作为氧化还原引发体系 ,甲基丙烯酸甲酯 丙烯酸丁酯 (MMA BA)作为混合单体 ,制备了分散相占 83 %以上的稳定的超浓乳液 ,然后在低温下引发聚合 .探讨了引发剂浓度、氧化剂与还原剂的摩尔比、乳化剂的浓度、液膜增强剂的种类、聚合温度等因素对聚合稳定性和聚合速率的影响 ,测定并计算得到了聚合速率的公式 ;用激光散射粒度分布仪测定了聚合物乳胶粒子的大小及粒径分布 ,用透射电子显微镜观察了聚合物乳胶粒的形态 ,讨论了乳化剂浓度、聚合温度等对乳胶粒形态、大小的影响     

基于氧化淀粉的新型Pickering苯丙乳液表面施胶剂的合成

以苯乙烯、丙烯酸丁酯为单体,过硫酸铵为引发剂,氧化淀粉作固体粒子乳化剂,采用无皂乳液聚合的方法来制备Pickering苯丙聚合物乳液,考察了不同含量的氧化淀粉对乳液固含量、转化率、卡伯值以及稳定性的影响,并对制备的Pickering苯丙聚合物乳液进行了粒径、红外光谱表征,当氧化淀粉的含量为2%时,制备的Pickering苯丙聚合物乳液转化率为96%,粒径为264.4nm,卡伯值为71.4g/m~2,抗水性和稳定性较好.     

氧化-还原引发剂引发苯乙烯超浓乳液聚合的研究

以过氧化羟基二异丙苯(CHPO)和四乙烯五胺(TEPA)为氧化-还原引发剂,以十二烷基硫酸钠(SDS)为乳化剂,十六醇(CA)为共乳化剂,通过超浓乳液聚合方法制备了聚苯乙烯乳胶粒子.探讨了乳化剂浓度及配比、分散相体积分数、引发剂种类、引发剂浓度及配比和温度等各因素对乳液稳定性、聚合速率、乳胶粒子大小、形态及分布的影响.用透射电子显微镜(TEM)观察了乳胶粒子的形态,用粘度法测定了聚苯乙烯的粘均分子量.考察了苯乙烯进行超浓乳液聚合的反应动力学,求得在30℃时聚合速率方程为Rp=K[M]^0.36[I]^0.49[E]^0.72,表观活化能为19.72kJ/mol.所得乳胶粒子的直径在0.1～0.3μm之间,粘均分子量在2×10⁶～4×10⁶之间.为低温下实现超浓乳液薄层聚合提供了参考数据.     

无皂乳液聚合制备含铕荧光共聚物乳液的研究及其表征

以丙烯酸(AA)为第一配体、邻菲罗啉(Phen)为第二配体、Eu3+为中心离子,合成了一种可聚合的稀土铕配合物.以配合物单体、甲基丙烯酸甲酯、丙烯酰胺和对苯乙烯磺酸钠为共聚单体,通过无皂乳液聚合的方法,制备了含铕荧光共聚物乳液.采用红外光谱对共聚物的结构进行了表征,并探讨了配合物单体含量对共聚物乳液性能的影响.透射电子显微镜(TEM)和激光光散射粒度仪(PCS)测试结果表明,共聚物乳液形成了相对均一的球状结构,但随着配合物单体含量增加,共聚物微球粒径逐渐增大、分散性变差.采用荧光分光光度计测试了共聚物乳液的荧光性能,在594和619 nm处出现Eu3+的特征发射光谱,且荧光强度随着配合物单体含量增加而增强.     

Preparation of poly(vinyl chloride) latexes by polymerization of stabilized monomer droplets

Poly(vinyl chloride) latexes have been prepared by polymerization in micron and submicron sized monomer droplets. Monomer emulsions with excellent long time stability were obtained by diffusional swelling of vinyl chloride monomer into preformed, stable polydisperse pre-emulsions of water-insoluble oils or monodisperse, oligomer styrene seed particles. It was found that the size and size distribution of the final latex particles were determined by those of the parent monomer emulsions. Except for the secondary particles formed during polymerization, the size and size distributions of the latex particles were found to be com-parable to those of the monomer emulsions employed, indicating a complete nucleation of the parent emulsion droplets. The extent of secondary particle formation was found to be very dependent upon the emulsifier concentration as well as on the type and amount of initiator used. © 1995 John Wiley & Sons, Inc.     

Synthesis and Characterization of Nano-silica/Polyacrylate Composite Emulsions by Sol-gel Method and in-situ Emulsion Polymerization

Organic nano-silica was firstly synthesized by sol-gel method with methyl methacrylate (MMA) and butyl acrylate (BA) in the micelles as dispersing media, tetraethoxysilicate (TEOS) as precursor, hydrochloric acid as catalyst and methacryloylpropyl trimethoxysilane (A174) as modifier. Subsequently, the nano-silica/polyacrylate composite emulsions were directly prepared by in-situ emulsion polymerization under the action of the initiator. The structure and properties were characterized by Fourier transform infrared spectroscopy (FTIR), dynamic light-scattering (DSL), thermogracvimetry (TG) and transmission electron microscopy (TEM). The results showed that A174-modified nano-silica was successfully synthesized in the acrylate-based emulsions by the sol-gel method. The nano-silica was encapsulated by polyacrylate, and the composite latex particles exhibited an apparent core-shell structure. The A174 could improve the lipophilicity of nano-silica and increase the grafting efficiency of polyacrylate on nano-silica particles. The nano-silica/polyacrylate composite latex film had better thermal stability, and the composite latex particles had greater average size and broader size distribution in contrast to those of pure polyacrylate emulsions.     

Elaboration of hydrophilic aminodextran containing submicron magnetic latex particles

Aminodextran containing submicron magnetic latex particles were prepared in two steps: (a) transformation of oil-in-water magnetic emulsion into structured magnetic latex particles via combination of seed and miniemulsion-like polymerization process and (b) immobilization (adsorption and chemical grafting) of prepared aminodextran onto negatively charged seed magnetic latex particles. The elaborated magnetic latex particles were characterized in terms of particle size, size distribution, morphology, surface charge density, chemical composition, magnetic properties, and also colloidal stability. The results showed that the morphology of the prepared seed magnetic latex is core–shell like and the cationic latex particles are hydrophilic and of high colloidal stability, irrespective of the aminodextran immobilization process.     

Synthesis of polystyrene/poly[2-(dimethylamino)ethyl methacrylate-stat-ethylene glycol dimethacrylate] core-shell latex particles by seeded emulsion polymerization and their application as stimulus-responsive particulate emulsifiers for oil-in-water emulsions

Surfactant-stabilized polystyrene (PS) latex particles with a mean hydrodynamic diameter of 155 nm were prepared by aqueous emulsion polymerization using 2,2'-azobis(2-amidinopropane) hydrochloride as a cationic radical initiator. Seeded aqueous emulsion copolymerizations of 2-(dimethylamino)ethyl methacrylate (DMA) and ethylene glycol dimethacrylate (EGDMA) were conducted in the presence of these PS particles to produce two batches of colloidally stable core-shell latex particles, in which the shell comprised a cross-linked P(DMA-stat-EGDMA) overlayer. Both the PS and PS/P(DMA-stat-EGDMA) latexes were characterized in terms of their particle size, morphology, and composition using dynamic light scattering, electron microscopy, and FT-IR spectroscopy, respectively. Using the PS/P(DMA-stat-EGDMA) latex particles as a pH-responsive particulate ('Pickering'-type) emulsifier, polydisperse n-dodecane-in-water emulsions were prepared at pH 8 that could be partially broken (demulsified) on lowering the solution pH to 3. These emulsions were characterized in terms of their emulsion type, mean droplet diameter, and morphology using electrical conductivity and Mastersizer measurements, optical microscopy, and scanning electron microscopy (using critical point drying for sample preparation).     

Interfacial properties of emulsions stabilized with surfactant and nonsurfactant coated boehmite nanoparticles

The properties of emulsions stabilized with surface-modified boehmite particles of 26 and 8 nm in diameter have been investigated. The surface-modified particles were prepared by mixing aqueous dispersions of cationic boehmite particles with aqueous solutions of the surfactant p-dodecylbenzenesulfonic acid (DBSA) or the nonsurfactant p-toluenesulfonic acid (TSA). For the 26 nm particles, interfacial tension measurements indicate that p-dodecylbenzenesulfonic acid partitions between the particle surface and the oil-water interface, while p-toluenesulfonic acid remains on the particle surface. The partitioning of p-dodecylbenzenesulfonic acid supports the formation of emulsions, although in the absence of the particles the same surfactant concentration is not sufficient for emulsion stabilization. Due to the fast exchange kinetics, p-dodecylbenzenesulfonic acid is gradually replaced by particles. At equilibrium, the interfacial tension in the presence of the surface-modified particles is between the values for the pure particles and the pure surfactant solutions. However, the interfacial tension is independent of the surfactant concentration used in the preparation of the particles. Reducing the particle size to 8 nm leads to increased emulsion stability, and thus, the minimum particle concentration required to prepare stable emulsions was reduced to 0.1 g/L. However, above approximately 3.5 mmol/L of the sulfonic acids, the small particles dissolve slowly, and the emulsion stability is lost. This mechanism can be used to trigger the collapse of the emulsions.     

Carboxylic‐group distribution of carboxylated acrylate copolymer latexes with their properties in the presence of acrylic acid and monobutyl itaconate

A series of carboxylated acrylate copolymer latexes were prepared via two different emulsion polymerization technologies with different carboxylic‐group distribution and morphologies. The effects of the emulsifier, the initiator, and the carboxylic monomers [acrylic acid (AA) or monobutyl itaconate (MBI)] on the total conversion of the monomers and the properties of acrylate latexes and films have been investigated. The distribution of carboxylic groups (?COOH) measured by conductometric titration shows that the concentration of surface –COOH (C_s) and embedded –COOH (C_b) both increase with the increase of the amount of carboxylic monomers. For the latexes containing AA, –COOH tends to distribute on the surface of latex particles and in the aqueous phase, whereas –COOH tends to concentrate inside the core of latex particles for the latexes containing MBI. Transmission electron microscopy demonstrates that the latex particles are regular with narrow size distribution and have significant differences in morphologies when different carboxylic monomers and polymerization technologies were used. The stability of latex is satisfactory through the results of common stability and zeta potential tests. Moreover, the water absorption and contact angle experiment tests also revealed that the water resistance of the latex films is good. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of Emulsifier Type on the Characterization of O/W Emulsions Using a Spectroscopy Technique

The droplet size distribution (DSD) of emulsions is the result of two competitive effects that take place during emulsification process, i.e., drop breakup and drop coalescence, and it is influenced by the formulation and composition variables, i.e., nature and amount of emulsifier, mixing characteristics, and emulsion preparation, all of which affect the emulsion stability. The aim of this study is to characterize oil-in-water (O/W) emulsions (droplet size and stability) in terms of surfactant concentration and surfactant composition (sodium dodecyl benzene sulphonate (SDBS)/Tween 80 mixture). Ultraviolet-visible (UV-vis) transmission spectroscopy has been applied to obtain droplet size and stability of the emulsions and the verification of emulsion stability with the relative cleared volume technique (time required for a certain amount of emulsion to separate as a cleared phase). It is demonstrated that the DSD of the emulsions is a function of the oil concentration and the surfactant composition with higher stability for emulsions prepared with higher SDBS ratio and lower relative cleared volume with the time. Results also show that smaller oil droplets are generated with increasing Tween 80 ratio and emulsifier concentration.     

纳米粘土对硅丙乳液的改性

采用原位乳液聚合方法,以纳米粘土改性硅丙乳液,并对所得复合乳液及其涂膜性能进行了研究,结果表明:复合乳液的储能模量、损耗因子和复合粘度较纯硅丙乳液均有明显提高,且其涂膜的耐热性能增强并具有优良的综合性能。     

Study of emulsion polymerization stabilized by amphiphilic polymer nanoparticles

Submicron-sized polystyrene (PS) microspheres with a relatively narrow particle size distribution can be easily produced through emulsion polymerization induced by γ-ray at room temperature using a new type of amphiphilic cross-linked poly(stearyl methacrylate-co-acrylamide-co-acrylic acid) particles as stabilizer. The properties of these amphiphilic particles were described, including morphology, size, ζ potential, and contact angles. The effect of the pH value and the content of amphiphilic particles on the formation and stability of emulsions were also investigated. Meanwhile, the obtained PS microspheres were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy. In addition, through observing the morphology and size of emulsion droplets at different times under an optical microscope, we found it is interesting that Pickering emulsions formed initially disappeared gradually, which is different from the common Pickering emulsions stabilized by inorganic particles. Thus, the mechanism was further discussed.