CO气体分子在金属氧化物SrO(001)表面吸附和脱附机理

研究了高纯度金属氧化物SrO粉末表面吸附C¹⁸O后在程序升温热脱附过程中的脱附反应规律,讨论了CO气体分子在SrO(100)表面吸附和脱附之间的关系及机理.SrO吸附C¹⁸O后,在升温过程中可通过氧的同位素交换生成C¹⁶O而脱附,同时伴随少量C¹⁸O的直接脱附,并与C¹⁶O具有相近的脱附活化能.C¹⁶O的脱附量随C¹⁸O气体暴露量增加而增加,但当气体覆盖度超过一定值后,脱附量趋于定值.脱附峰值温度随气体暴露量的增加而下降.     

MIL-101(Cr)/GO复合吸附剂的O2/N2分离性能研究

变压吸附（PSA）制取O₂的核心是吸附剂.近年来,金属有机骨架（MOFs）被认为是一种具有广阔应用前景的新型吸附剂.通过水热法制备了MIL-101（Cr）/氧化石墨烯（GO）.结果表明,MIL-101（Cr）/GO-15具有更高的比表面积（3486 m²·g^-1）和更大的孔体积（2.39 cm³·g^-1）,因此也表现出更高的O₂吸附量（0.54 mmol·g^-1）.进一步根据理想吸附溶液理论（IAST）预测了其在O₂/N₂体积比为1：4混合气体中的O₂/N₂选择性为1.2,相比MIL-101（Cr）提高了17.65%.同时,MIL-101（Cr）/GO-15的循环利用性能更佳,经过三次O₂吸脱附循环后,依然拥有高达80%的O₂吸附量,具有较好的循环再生性能.     

SiO2-Al2O3玻纤载体负载CuO-CeO2对挥发性有机化合物催化燃烧性能研究

采用等体积共浸渍法制备了CuO-CeO₂整体式催化剂,评价了催化剂对乙酸乙酯、异丙醇及甲苯的催化燃烧性能。采用N₂吸附-脱附、X射线衍射（XRD）、氢气程序升温还原（H₂-TPR）、氨气程序升温脱附（NH₃-TPD）以及挥发性有机化合物脱附等手段对催化剂进行了表征。表征数据显示,氧化铜以高分散态均匀分散存在于载体表面,氧化铈则是小的纳米颗粒,氧化铈颗粒粒径随着Cu/Ce物质的量比的减小而增大。添加铈氧化物会显著增加总酸量,特别是路易斯酸酸位的量,同时增强了乙酸乙酯和异丙醇的吸附量,吸附量的增加提高了催化剂对乙酸乙酯和异丙醇的催化燃烧性能。从甲苯的催化燃烧实验可以看出,大量添加CeO₂稍微增加了甲苯的吸附容量,减弱了催化剂的还原性、降低了活性氧的含量,最终导致甲苯的低转化率。催化行为由氧化铜、氧化铈以及载体三者之间的共同作用决定,这三者的协同作用不仅影响着表面氧的活性同时影响着催化剂对甲苯的吸附能力。     

四乙烯五胺修饰介孔硅胶吸附CO2性能的研究

采用浸渍法将四乙烯五胺(TEPA)负载到介孔硅胶(SG)上,制备了一系列胺功能化的CO₂吸附材料(TEPA-SG).利用傅里叶变换红外光谱(FT-IR)、热重分析(TGA)和N₂吸脱附等分析方法对样品进行了表征,并在固定床反应器中考察了TEPA负载量、吸附温度对CO₂吸附性能的影响,同时通过添加不同质量分数的聚乙二醇(PEG)考察了羟基对吸附性能及再生性能的促进作用.结果表明,当TEPA负载量为40%(质量分数)、吸附温度为70 ℃时,TEPA-SG的吸附量高达2.21 mmol/g;PEG的加入改变了氨基与CO₂的相互作用机理,当TEPA与PEG的质量比为3:1,总负载量为40%时,CO₂的吸附量为2.70 mmol/g,且经过10次吸脱附循环实验后,CO₂吸附量仍保持在2.66 mmol/g,表现出较好的循环稳定性.Clausius-Clapeyron方程计算得该过程的等量吸附热为30~40 kJ/mol,且随吸附量的增大等量吸附热逐渐减小,表明TEPA30/PEG10-SG吸附剂表面存在能量不均匀性.     

NO气体在TiO2表面的吸附行为

采用TPD (Temperature Programmed Desorption)试验方法测定了NO在TiO₂表面吸附后的脱附谱, 揭示了气体脱附量的变化规律. 结果表明, NO在TiO₂表面吸附后可在两个峰值温度450和980 K脱附出N₂气体, 其活化能分别是0.48 和2.5 eV. TiO₂表面经预覆氧处理后, N₂的脱附量降低. N₂的脱附量随NO气体暴露量增加而增加, 但当气体覆盖度超过一定值后, 脱附量趋于定值. 脱附峰值温度随气体暴露量的增加而降低.     

NO气体在TiO2表面的吸附行为

采用TPD (Temperature Programmed Desorption)试验方法测定了NO在TiO₂表面吸附后的脱附谱, 揭示了气体脱附量的变化规律. 结果表明, NO在TiO₂表面吸附后可在两个峰值温度450和980 K脱附出N₂气体, 其活化能分别是0.48 和2.5 eV. TiO₂表面经预覆氧处理后, N₂的脱附量降低. N₂的脱附量随NO气体暴露量增加而增加, 但当气体覆盖度超过一定值后, 脱附量趋于定值. 脱附峰值温度随气体暴露量的增加而降低.     

MnOx/SAPO-11催化剂的制备、表征及其低温NH3-SCR活性

分别采用浸渍法、柠檬酸络合法以及沉淀法在SAPO-11分子筛上负载MnO_x,制备了一系列MnO_x/SAPO-11催化剂。考察了催化剂的低温NH₃选择性催化还原(SCR) (NH₃-SCR) NO_x的性能。结果表明,沉淀法制备的负载量为20%(w)的MnO_x/SAPO-11催化剂表现出最优异的低温NH₃-SCR性能及N₂选择性。通过X射线衍射(XRD)、扫描电镜(SEM)、能量散射谱(EDS)、原子吸收光谱(AAS)、N₂吸附-脱附、X射线光电子能谱(XPS)、H₂程序升温还原(H₂-TPR)、NH₃程序升温脱附(NH₃-TPD)以及NO/O₂程序升温脱附-质谱(NO/O₂-TPD-MS)等多种表征手段对催化剂的结构及表面性质进行分析。表征结果显示,采用不同方法制备催化剂时,其表面MnO_x的存在形式和晶相结构不同。沉淀法制备的催化剂表面存在无定型态MnO_x以及MnO₂晶型,具有较大的介孔及外表面积、更多比例的Mn⁴⁺和化学吸附氧,同时表面存在对反应有利的中强酸以及强酸。因此,催化剂在低温SCR反应阶段能够生成重要中间产物NO₂,从而表现出最佳低温活性。同时,三种制备方法均能使MnO_x相对均匀分散在SAPO-11表面。SAPO-11对催化剂表面MnO_x物种的形成具有一定的影响,从而影响催化剂的酸性,拓宽了MnO_x的活性温度窗口,提高了催化剂的N₂选择性。     

浓凝胶转换法制备纳米SAPO-34及其CH4/N2吸附分离性能研究

通过浓凝胶转换法合成了一种厚度约为50 nm, 大小约为200 nm的纳米片状SAPO-34分子筛, 经XRD, SEM, ICP和氮气(77 K)吸附-脱附等方法对其进行了表征, 结果显示, 相比于微米级立方体形的SAPO-34 (2 μm), 本文合成的纳米片状SAPO-34表现出更高的比表面积(818.68 m²/g)和孔容(0.57 cm³/g). 比表面和孔容积的增大使其气体吸附容量得到较大的提升, 其中CH₄的吸附容量达到25.74 cm³/g, 提升了60%, 高于绝大多数分子筛吸附剂, 同时CH₄/N₂的吸附选择性未出现明显下降(3.1), 且达到商用吸附剂水平(＞3.0). 通过CH₄/N₂(体积比1∶1, 298 K)混合气体穿透测试证明所合成的纳米SAPO-34是一种有效的CH₄/N₂分离吸附剂, 在煤层气富集脱氮工业中具有极大的应用潜力.     

不同WO3含量对CeO2-ZrO2-WO3催化剂在NH3选择性催化还原NO中的影响

采用水热法制备了CeO₂-ZrO₂-WO₃(CZW)催化剂,考察了WO₃含量对CZW催化剂上NH₃选择性催化还原NO_x性能的影响,并利用X射线衍射、N₂吸附-脱附、H₂程序升温还原、NH₃和NO程序升温脱附等方法对其进行了表征。结果表明,WO₃以无定形的形式存在于催化剂中,添加WO₃后显著提高了催化剂的表面酸性,并且在CZW催化剂上出现了强吸附的NO物种,从而有利于提高催化剂的活性。另外,适量的WO₃引入将增大催化剂的比表面积,促进催化剂的氧化还原性能,这将有利于提高SCR的催化活性。和CeO₂-ZrO₂催化剂相比,当WO₃的含量为20%时,CZW催化剂表现出良好的抗硫性能。此外,当空速为60 000 h^-1时,在200~463 ℃,该催化剂显示出了大于90% NO_x转化率。     

铈掺杂氧化锌（1000）晶面的SO2吸附性能研究

基于密度泛函理论,仿真建立了铈（Ce）掺杂氧化锌ZnO（1000）晶面的SO₂分子吸附模型,并计算了其吸附能、电荷转移量、吸附距离、电子态密度及脱附时间以探究吸附及脱附特性.计算得到Ce掺杂ZnO（1000）晶面的SO₂吸附结构有较大的吸附能（-1.66 eV）,且在温度为398 K时,该体系具有符合实际传感检测过程的脱附时间（1.433×10³ s）.结果表明Ce掺杂ZnO（1000）晶面对SO₂分子显示出优异的吸脱附性能.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。