硝基化合物的吸附伏安法研究 I: 5-硝基-1, 10-邻菲咯啉的吸附伏安特性

本文用线性扫描技术对氨性溶液中, 低浓度, 5-硝基-1,10-邻菲咯啉的吸附伏安特性进行了研究.     

镓(Ⅲ)-茜素红体系的吸附伏安法

本文对镓(Ⅲ)与茜素红络合物在悬汞电极上的吸附伏安法作了研究,确定了电极过程.在HAc-NH_4Ac(pH4.06)缓冲溶液中茜素红存在下,用1.5阶微分吸附伏安法测定镓,其线性范围是1×10~(-10)～1×10~(-7)mol/L,其检测限为1×10~(-10)mol/L,并用此法测定了中草药中的痕量镓.     

微量铁的吸附伏安法测定

在NH_3-NH_4Cl-三乙醇胺底液中用5-Br-PADAP催化极谱法测定铁的检测下限为2.8×10~(-8)mol/L。本文利用吸附伏安法,先进行吸附富集,形成的Fe-5-Br-PADAP在HAc-NaAc介质中产生灵敏的络合吸附峰,将检测下限提高到4.0×10~(-10)mol/L。 实验采用悬汞电极、铂电极和饱和甘汞电极组成的三电极体系。1.0×10~(-2)mol/L含     

尼莫地平的吸附伏安行为

在NH_3-NH_4Cl底液中,尼莫地平(nimodipine,NMD)在汞电极上有一线性扫描还原峰,峰电位E_(pc)=-0.62V(vs.Ag/AgCl).该峰具有明显的吸附性,吸附粒子为NMD中性分子.测得NMD在汞电极上的饱和吸附量为1.49 ×10~(-10)mol/cm~2,每个NMD分子所占电极面积为1.11nm~2,NMD在悬汞电极上的吸附符合Frumkin等温式.测得吸附系数β=4.32×10~5,吸附因素γ=0.46;吸附自由能△G°=-32.14kJ/mol;电子转移数n=4;不可逆吸附的动力学参数αn_α为1.10.探讨了NMD在汞电极上的还原机理,并建立了吸附溶出伏安法测定NMD的最佳条件,检测限为1.0×10~(-9)mol/L.     

阿西美辛的吸附伏安特性

在乙酸 -乙酸钠 ( p H 4.2 0 )底液中 ,阿西美辛 ( ACE)在汞电极上有一线性扫描还原峰 ,峰电位 Epc=- 1 .1 8V( vs.Ag/Ag Cl) ,该峰具有明显的吸附性。吸附粒子为 ACE中性分子 ,测得 ACE在汞电极上的饱和吸附量为 1 .1 9× 1 0 - 10 mol/cm2 ,每个 ACE分子所占电极面积为 1 .43nm2 ,ACE在悬汞电极上的吸附符合 Frumkin等温式。测得吸附系数β =1 .2 9× 1 0 6 ,吸引因素γ =1 .0 4 ,电子转移数 n为 2 ,不可逆吸附的电子转移系数α为 0 .86,表面电极反应速率常数 ks=0 .32 /s。建立了吸附伏安法测定 ACE的最佳条件 ,检出限为 1 .0× 1 0 - 9mol/L     

碳糊电极吸附溶出伏安法测定游离钙

基于Ca(Ⅱ)-茜素红S(ARS)络合物在碳糊电极上的还原波,建立了吸附溶出伏安测定游离钙的新方法。在1.5×10-2mol/LKOH-2.0×10-5mol/LARS介质中,Ca(Ⅱ)-ARS络合物在碳糊电极上于-0.89V处产生一吸附还原波。当富集电位为.0.1V,富集时间90s,扫描速度为100mV/s时,该络合物单扫描阴极溶出峰的二阶导数峰电流与游离钙离子浓度在3.0×10-8~2.0×10-6mol/L范围内呈线性关系;检出限为9.4×10-9mol/L。在0.2mol/LHCl中清洗2min,该电极重现性良好。该方法可用于血清、牛奶和自来水中游离钙的测定。     

吸附伏安法测定痕量镍

镍是人体所必需的微量元素,当镍元素缺乏时,往往会引起血红蛋白和红细胞的减少,然而镍在人体内积累过量时,又会导致肺癌,所以在生态化学研究中测定微量镍是十分重要的。 文献[1]报道在氯化铵—亚硫酸钠介质中用镍—锌试剂(Zincon)示波极谱测定微量镍,检出下限为2.7×10~(-7)·L~(-1)。本文用79—1型伏安分析仪对Ni(Ⅱ)—Zincon—NH_3·NH_4Cl体系做了线性扫描吸附伏安法的研究,发现在氨—氯化铵介质中Ni(Ⅱ)—Zincon有一明显的吸附还原峰,用常规法检出下限降低了两个数量级,可达2.5×10~(-9)mol·L~(-1),用于测定人发中的痕量镍,结果满意。     

硝基化合物的吸附伏安法研究 Ⅰ.5-硝基-1,10-邻菲咯啉的吸附伏安特性

吸附伏安法是一种高灵敏度的简单的电分析化学方法。对不可逆过程的线性变势技术,灵敏度比无吸附时大3—4个数量级。利用配合物的吸附,可以测定痕量无机离子。配位体的吸附伏安特性是一个十分重要的因素。5-硝基-1,10-邻菲咯啉(Phen-NO_2)是一种常用的配位体,它的吸附伏安特性还未见报道。本文用线性扫描技术对氨性溶液中,低浓度Phen-NO_2的吸附伏安特性进行了研究。     

舒乐安定吸附伏安法的研究

Jimenez曾研究了舒乐安定的性质,但灵敏度较低,本文提出了测定痕量舒乐安定的吸附伏安法,在0.1 mol/L NH_3-NH_4Cl溶液(pH 9.3)中,富集电位—0.80 V(us. Ag/AgCl)得一灵敏的舒乐安定还原峰,Ep=—1.05 V,i_p与舒乐安定浓度在3.0×10~(-9)～5.0×10~(-6) mol/L范围内呈线性关系,检测限达1.0×10~(-9)mol/L,并用于试样的测定,用循环伏安法和恒电     

碳糊电极阳极吸附伏安法测定洛美沙星

报道了碳糊电极阳极吸附伏安法测定洛美沙星的新方法。在0.096mol L的KHP NaOH(pH5.4)缓冲液中,用碳糊电极为工作电极,在0.3V(vs.SCE)富集一定时间,然后从0.3～1 3V以300mV s扫速线性扫描,记录其在1 02V的二次导数阳极溶出峰。溶出峰电流与洛美沙星浓度在8.0×10-9～8.0×10-8mol L(富集90s)和8.0×10-8～8.0×10-7mol L(富集30s)范围内呈良好的线性关系,相关系数分别为0.9844和0.9967,检出限为9.0×10-10mol L(S N=3)。探讨了洛美沙星在碳糊电极上的伏安性质和电极反应机理,并且成功地应用于人体尿液中洛美沙星的测定,结果与紫外光度法基本吻合。     

Cathodic adsorptive stripping voltammetric studies on lamivudine: an antiretroviral drug

The electrochemical reduction and adsorption of lamivudine, a systemic antiviral drug, were studied in a phosphate buffer medium at a hanging mercury drop electrode (HMDE). Cyclic voltammetry studies showed one well-defined reduction peak in the potential range from -1.2 to -1.8 V under different pH conditions, but the best results were obtained at pH 3.4. The reduction was irreversible and exhibited diffusion-controlled adsorption. The response was evaluated with respect to preconcentration time, pH effect, accumulation potential, accumulation time, and scan rate. The number of electrons transferred in the reduction process was calculated and the probable reduction mechanism was proposed. A systemic study of the experimental parameters that affect the square-wave stripping response was carried out and experimental conditions were optimized.     

Differential pulse cathodic stripping voltammetry of the copper complexes of glycyl-L-histidyl-glycine at a hanging mercury drop electrode

The behaviour of the copper complexes of glycyl-L-histidyl-glycine (GHG) was investigated using cyclic voltammetry and differential pulse voltammetry after their adsorptive accumulation on the surface of a hanging mercury drop electrode (HMDE). The nature of the observed cathodic and anodic peaks was established and optimum conditions were found for the differential pulse cathodic stripping voltammetric detemination of GHG at the 1 x 10(-8)M concentration level using adsorptive accumulation at -0.20 V vs. Ag/AgCl reference electrode and the cathodic stripping peak around -0.4 V (pH 8.3). This peak corresponds to the reduction of the Cu(I)-GHG complex formed at the HMDE surface as an intermediate in the reduction of Cu(II)-GHG to Cu(O)amalgam.     

Determination of ketorolac in human serum by square wave adsorptive stripping voltammetry

The adsorption behavior of ketorolac on a hanging mercury drop electrode (HMDE) was explored by square-wave and cyclic voltammetry. The square wave voltammetric response of ketorolac depends on the parameters of the square wave voltammetry excitation signal as well as on the pH of the medium and the accumulation time. The drug was accumulated at HMDE and a well-defined peak was obtained at -1.41 V versus. Ag/AgCl (saturated KCl) in acetate buffer of pH 5.0. A square-wave adsorptive stripping voltammetric method for the quantitative determination of ketorolac was developed. The linear concentration range was 1x10(-10)-1x10(-8) when using 300 s accumulation at -0.8 V. The detection limit of ketorolac was 1.0x10 (-11)M . The precision was excellent with relative standard deviation of 3.85% at concentration of 5x10 (-8)M after 60 s accumulation time. Applicability to serum samples was illustrated. A detection limit of 14 ng per ml of serum was obtained.     

Direct determination of molybdenum in seawater by adsorption cathodic stripping square-wave voltammetry

A reliable and very sensitive procedure for the determination of trace levels of molybdenum in seawater is proposed. The complex of molybdenum with 8-hydroxyquinoline (Oxine) is analyzed by cathodic stripping square-wave voltammetry based on the adsorption collection onto a hanging mercury drop electrode (HMDE). This procedure of molybdenum determination was found to be more favorable than differential pulse cathodic stripping voltammetry because of inherently faster scan rate and much better linearity obtained through the one-peak (instead of one-of-two peaks) calibration. The variation of polarographic peak and peak current with a pH, adsorption time, adsorption potential, and some instrumental parameters such as scan rate and pulse height were optimized. The alteration of polarographic wave and its likely mechanism are also discussed. The relationship between peak current and molybdenum concentration is linear up to 150 mug l(-1). Under the optimal analytical conditions, the determination limit of 0.5 mug l(-1) Mo was reached after 60 s of the stirred collection. The estimated detection limit is better than 0.1 mug l(-1) of Mo. The applicability of this method to analysis of seawater was assessed by the determination of molybdenum in two certified reference seawater samples (CASS-2 and NASS-2) and the comparison of the analytical results for real seawater samples (study on a vertical distribution of Mo in the seawater column) with the results obtained by Zeeman-corrected electrothermal atomization atomic absorption spectrometry (Zeeman ETAAS). A good agreement between two used methods of molybdenum determination was obtained.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily     

Cathodic adsorption voltammetry of palladium(II)

The electrochemical behavior of palladium(II) was studied by differential pulse, linear sweep, and alternating-current square-wave voltammetry in HC1, HNO₃, H₂SO₄, and HC1O₄ solutions in the presence of dimethylglyoxime. A peak with a height linearly depending on the concentration of palladium(II) was observed in voltammograms. Typical relationships between the height and potential of a peak and pH, dimethylglyoxime concentration, the potential and time of adsorption accumulation suggested that the observed peak was due to the hydrogen liberation catalyzed by palladium(II) dimethylglyoximate adsorbed on the electrode surface. The detection limits for palladium(II) accumulated for 120 s at -0.2 V were 2 x 10^-8, 5 x 10^-9, and 8 x 10^-10 M for differential pulse, linear sweep, and alternating-current square-wave voltammetry, respectively.     

Cathodic adsorptive stripping square-wave voltammetry of the anti-inflammatory drug meloxicam

The adsorptive behavior of the anti-inflammatory drug meloxicam was studied by cyclic, differentia-pulse and square-wave voltammetry on a hanging mercury drop electrode (HMDE). The drug was accumulated at HMDE and a well-defined stripping peak current was obtained at -1.42 V vs. Ag/AgCl (saturated KCl) electrode in acetate buffer solution (pH 5.0). A voltammetric procedure was developed for the determination of meloxicam using square-wave cathodic adsorptive stripping voltammetry (SW-CASV). The optimum working conditions for the determination of the drug were established. The analysis of meloxicam in human plasma was carried out satisfactorily.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily Received: 10 July 1997 / Revised: 1 April 1998 / Accepted: 6 April 1998