Synthesis, characterization and photoluminescence properties of CaSiO3:Eu3+ red phosphor

CaSiO3:Eu3+ (1-5 mol%) red emitting phosphors have been synthesized by a low-temperature solution combustion method. The phosphors have been well characterized by powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and optical spectroscopy. PXRD patterns reveal monoclinic CaSiO3 phase can be obtained at 900°C. The SEM micrographs show the crystallites with irregular shape, mostly angular. Upon 254 nm excitation, the phosphor show characteristic fluorescence 5D0→7FJ (J=0, 1, 2, 3, 4) of the Eu3+ ions. The electronic transition located at 614 nm corresponding to 5D0→7F2 of Eu3+ ions, which is stronger than the magnetic dipole transition located at 593 nm corresponding to 5D0→7F1 of Eu3+ ions. Different pathways involved in emission process have been studied. Concentration quenching has been observed for Eu3+ concentration>4 mol%. UV-visible absorption shows an intense band at 240 nm in undoped and 270 nm in Eu3+ doped CaSiO3 which is attributed to oxygen to silicon (O-Si) ligand-to-metal charge-transfer (LMCT) band in the SiO3(2-) group. The optical energy band gap is widened with increase of Eu3+ ion dopant.     

YAl3（BO3）4∶Eu3+荧光粉的化学沉淀法制备研究

以化学沉淀法制备单相的铕离子掺杂硼铝酸盐红色荧光粉YAl3(BO3)4∶Eu3+,考察了焙烧温度、掺铕量等因素对材料性能的影响,用X射线衍射、扫描电镜、激发光谱和发射光谱对荧光粉的结构、形貌和发光性能进行了表征.以尿素为沉淀剂,900℃焙烧沉淀前驱体可得到单相荧光粉YAl3(BO3)4∶Eu3+,反应温度比传统高温固相法降低了300℃;沉淀法制备的荧光粉粒径分布范围小,无团聚现象,粒径约300nm.掺铕量为10%(物质的量比)时发光强度最大.在260nm的紫外光激发下,Eu3+的5 D0→7 F2的电偶极跃迁最强,发射光为618nm的红光.     

橙红色荧光粉BaZnP2O7∶Eu3+的制备与发光特性

采用高温固相法合成了BaZnP2O7∶Eu3+荧光粉, 并对其发光性质进行了研究.     

CaF_2微晶玻璃的一步法制备及Eu~(3+)离子探针特性

以组成为n(SiO_2)∶n(Al2O3)∶n(CaO)∶n(CaF_2)∶n(NaF)∶n(B_2O_3)=40∶20∶10∶10∶15∶5的微晶发光玻璃为基质,采用一步析晶法制备了CaF_2析晶相.利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、X射线能量散射谱仪(EDS)和荧光分光光度计等对样品结构、组成及光谱性能进行分析,探讨了Eu3+掺杂浓度和析晶温度对微晶玻璃发光性能的影响.实验结果表明,在850℃下处理可获得分布均匀、粒径尺寸为200 nm的CaF_2析晶相,微晶玻璃的发光强度是基质玻璃的1.7倍.微晶玻璃的发射光谱在590,614,652和700 nm出现发射峰,分别对应Eu3+的5D0-7FJ(J=1,2,3,4)跃迁.通过对5D0-7F1和5D0-7F2跃迁强度的分析以及Judd-Ofelt理论参数Ω2值的计算可知Eu3+周围晶体场在析晶前后对称性发生变化.机理分析表明,析晶处理后Eu3+从高声子能量的Si-O环境进入低声子能量的Ca-F环境中,说明Eu3+可作为荧光探针研究微晶玻璃晶体结构的变化.     

Hydrothermal synthesis and fluorescence of YF3: Eu3+

<正>Europium(Ⅲ)-doped YF_3 is prepared by a hydrothermal process at 200℃.X-ray diffraction(XRD) pattern identifies the formation of YF_3 phase without detectable impurity.Environment scanning electron microscopy(ESEM) image shows the even size distribution of the samples with cubic morphology.The excitation and emission spectra of the rare earth ions doped YF_3 are investigated by fluorescence spectrophotometer.The excitation spectrum for 591 nm emission has several excitation bands at 320, 365,386,397 and 467 nm,and the main peak value was 397 nm.Typical Eu~(3+) emission peaks at 591 nm(~5D_0→~7F_1) and 612 nm (~5D_0→~7F_2) are observed when excited by 397 nm,and the strongest emission is 591 nm,demonstrating that the rare earth ions occupy the centrosymmetrical sites in YF_3.     

GdF3∶Eu3+/NaGdF4∶Eu3+纳米晶的水热合成及发光性质

采用水热法,以聚乙二醇(400)为分散剂,以NaOH和HNO3溶液调节初始溶液pH值,合成GdF3∶Eu3+和NaGdF4∶Eu3+纳米晶。XRD和SEM结果表明:在酸性溶液(pH=3,5)、中性溶液(pH=7)和碱性溶液(pH=9)中,分别获得具有正交结构的GdF3∶Eu3+纳米晶,GdF3∶Eu3+和NaGdF4∶Eu3+混合晶,六方结构NaGdF4∶Eu3+棒状微米晶。根据Scherrer公式估算pH=3和pH=5时制备纳米晶的一次性粒径分别为49和28 nm。样品的发射光谱结果表明:特征发射峰来自于5D2、5D1、5D0到7FJ跃迁。在主晶相为GdF3样品中,主发射峰来自于Eu3+的5D0→7F1的磁偶极跃迁;晶相为NaGdF4样品的主发射峰来自于Eu3+的5D0→7F2电偶极跃迁。5D0→7F1和5D0→7F2跃迁发射相对强度比值显示:Eu3+在NaGdF4晶体中的格位对称性下降。激发光谱显示出Gd3+和Eu3+具有较好的能量传递。     

TiO2对ZnO/ZnS:Eu3+荧光粉发光性能的影响

采用溶胶-凝胶-沉淀法制备ZnO/ZnS/2TiO2:Eu3+荧光粉,并采用X射线衍射(XRD)、红外光谱(IR)、透射电镜(TEM)以及荧光光谱技术对其结构、组成、形貌和发光性能进行表征,探讨其发光机理。结果显示,ZnO/ZnS/2TiO2:Eu3+荧光粉的结构在温度高于600℃时趋于稳定状态,呈不规则结构,由ZnO、TiO2和ZnS构成。IR谱图表明,Ti-O-Ti桥氧键网络结构有利于Eu3+之间的能量传递。荧光光谱分析表明,引入TiO2使Eu3+光谱选律禁阻解除,提高了ZnO/ZnS/2TiO2:Eu3+荧光粉的发光性能,且当nZn(NO3)2:nTiO2=1:2时荧光粉的发光性能最好,612 nm处的5D0→7F2电偶极跃迁为最强发射峰,最佳退火温度为600℃。     

Bifunctional Mixed-Lanthanide Cyano-Bridged Coordination Polymers Ln(0.5)Ln'(0.5)(H(2)O)(5)[W(CN)(8)] (Ln/Ln' = Eu(3+)/Tb(3+), Eu(3+)/Gd(3+), Tb(3+)/Sm(3+))

A new family of mixed-lanthanide cyano-bridged coordination polymers Ln(0.5)Ln'(0.5)(H(2)O)(5)[W(CN)(8)] (where Ln/Ln' = Eu(3+)/Tb(3+), Eu(3+)/Gd(3+), and Tb(3+)/Sm(3+)) containing two lanthanide and one transition metal ions were obtained and characterized by X-ray diffraction, photoluminescence spectroscopy, magnetic analyses, and theoretical computation. These compounds are isotypical and crystallize in the tetragonal system P4/nmm forming two-dimensional grid-like networks. They present a magnetic ordering at low temperature and display the red Eu(3+) ((5)D(0) → (7)F(0-4)) and green Tb(3+) ((5)D(4) → (7)F(6-2)) characteristic photoluminescence. The Tb(0.5)Eu(0.5)(H(2)O)(5)[W(CN)(8)] compound presents therefore green and red emission and shows Tb(3+)-to-Eu(3+) energy transfer.     

新型双钼酸盐红色荧光粉的制备及发光性能研究

采用高温固相法合成了一种新型的白光LED用双钼酸盐红色荧光粉,利用XRD,F-4500等对其进行了研究。结果表明:该系列荧光粉可以被近紫外光(396 nm)和蓝光(466 nm)有效激发,发射峰值位于615 nm(Eu3+离子的5D0→7F2跃迁)的红光;而且在钾铕双钼酸盐荧光粉KEu(MoO4)2中引入适量的钨酸能加强其发光强度,而不改变样品的发射光谱的形状和发射峰的位置。此外,在确定WO24-/MoO42最佳比值的前提下,文章还详细探讨了碱金属离子相互置换对样品发光性能影响的机制。     

绿色荧光粉KNaCa2（PO4）2:Tb3+的制备及发光性能研究

采用高温固相法成功制备了KNaCa2(PO4)2:Tb3+绿色荧光粉,并研究了其发光性质。测量了其激发和发射光谱,样品发射峰位于418,440,492,545,586,622 nm,分别对应Tb3+的5 D3→7 F5,5 D3→7 F4,5 D4→7 F6,5 D4→7 F5,5 D4→7 F4,5 D4→7 F3能级跃迁,主发射峰位于545 nm。主激发峰位于350～390 nm之间,属于4f→4f电子跃迁吸收,与InGaN管芯匹配。确定了在KNaCa2(PO4)2基质中Tb3+浓度对其发光强度的影响及其自身浓度猝灭机制。研究了不同电荷补偿剂对KNaCa2(PO4)2:Tb3+材料发光的影响,其中Li+离子改善其发光强度最为明显。     

Gd3Ga5O12∶Eu3+发光纳米晶的燃烧合成及性质

以尿素为燃烧剂,乙二醇为分散剂采用燃烧法制备了Gd3Ga5O12∶Eu3+纳米晶。利用X射线衍射、电镜和荧光光谱对前驱体和热处理后样品的结构、形貌和发光性能进行了表征。XRD结果表明:700℃热处理2 h即可获得立方结构Gd3Ga5O12∶Eu3+纳米晶。根据Scherrer公式估算经700℃和900℃热处理2 h获得的纳米晶的一次性粒径分别为28 nm和42 nm。发射光谱和激发光谱的结果表明:特征发射峰来自于5D0-7FJ跃迁,而来自于Eu3+的5D0→7F1的磁偶极跃迁发射最强;宽激发带主要来自于Eu-O电荷迁移带和Gd3Ga5O12基质吸收。发射强度和激发强度随热处理温度的提高而增强。     

Luminescent properties of pure cubic phase Y2O3/Eu3+ nanotubes/nanowires prepared by a hydrothermal method

One-dimensional pure cubic Y(2)O(3)/Eu(3+) nanocrystals (NCs) were synthesized by a hydrothermal method at various temperatures. The NCs prepared at 130 degrees C yielded nanotubes (NTs) with wall thickness of 5-10 nm and outer diameter of 20-40 nm. The NCs prepared at 170 and 180 degrees C yielded nanowires (NWs) with diameters of approximately 100 and approximately 300 nm, respectively. Their luminescent properties, including electronic transition processes, local environments surrounding Eu(3+) ions, electron-phonon coupling, and UV light irradiation induced spectral changes have been systematically studied and compared. The results indicate that the Y(2)O(3)/Eu(3+) NTs and NWs have strong red (5)D(0)-(7)F(2) transitions. The fluorescence lifetime of (5)D(1)-(7)F(1) hardly changes in different samples, while that of (5)D(0)-(7)F(2) decreases a small amount in Y(2)O(3)/Eu(3+) NTs. The (5)D(0)-(7)F(2) lines originate from the emissions of Eu(3+) ions occupying one C(2) site, like that in the bulk powders. The phonon sideline with a frequency shift of 40-50 cm(-1) appears at the low-energy side of the (7)F(0)-(5)D(0) zero phonon line. The relative intensity of the sideline to zero phonon line increases by varying from NTs to NWs, and the spectral position of the phonon sideline shifts red. The UV light irradiation induced spectral change in the charge-transfer band was studied. The results indicate that the spectral change is dependent on sample size and is wavelength selective. A detailed model was proposed to explain the light-induced spectral change.     

Luminescence and microstructures of Eu(3+)-doped Ca9LiGd(2/3)(PO4)7

A red-emitting phosphor, Eu(3+)-doped Ca(9)LiGd(2/3)(PO(4))(7), was synthesized by the conventional high-temperature solid-state reaction. X-ray powder diffraction (XRD) analyses confirmed the pure crystalline phase of Whitlockite-type structure. The excitation spectra of Eu(3+) doped Ca(9)LiGd(2/3)(PO(4))(7) were measured in the VUV and UV region indicating an efficient energy transfer process from the host and Gd(3+) to Eu(3+) ions. Upon excitation with VUV and UV radiation, the phosphor showed strong red emission around 611 nm corresponding to the forced electric dipole (5)D(0)→(7)F(2) transition of Eu(3+) ions. The VUV- and UV-excited luminescence spectra of Ca(9)LiGd(2/3)(PO(4))(7):Eu(3+) together with the dependence of the integrated emission intensities on the doping levels were investigated. The Eu(3+) ions were investigated by a tunable laser as an excitation source. The excitation spectra of (7)F(0)→(5)D(0) transitions suggest that there are two families of inequivalent sites for Eu(3+) in this host. The concentration quenching and crystallographic site-occupancy of Eu(3+) ions in Ca(9)LiGd(2/3)(PO(4))(7) host were discussed on the basis of the site selective excitation and emission spectra, the luminescence decay and its crystal structure.     

Preparation, characterization and photoluminescence properties of BaB2O4: Eu3+ red phosphor

A new red emitting BaB2O4: Eu3+ phosphor was synthesized by solid-state reaction method. X-ray powder diffraction (XRD) analysis confirmed the monoclinic formation of BaB2O4. Field-emission scanning electron-microscopy (FE-SEM) observation indicated that the microstructure of the phosphor consisted of irregular grains with heavy agglomerate phenomena. Upon excitation with 394 nm light, the BaB2O4: Eu3+ phosphor shows bright red emissions with the highest photoluminescence (PL) intensity at 611 nm due to 5D0→7F2 transitions of Eu3+ ions. The CIE chromaticity coordinates are calculated from the emission spectrum to be x=0.64, y=0.35. The effects of the Eu3+ concentration on the PL were investigated. The results showed that the optimum concentration of Eu3+ in BaB2O4 host is 6 mol% and the dipole-dipole interaction plays the major role in the mechanism of concentration quenching of Eu3+ in BaB2O4: Eu3+ phosphor. The effect of charge compensation on the emission intensity was also studied. The charge compensations of Li+, Na+ and K+ anions all increased the luminescent intensity of BaB2O4: Eu3+. K+ anion gave the best improvement to enhance the intensity of the emission, indicating K+ is the optimal charge compensator. All properties show that this phosphor could serve as a potential candidate for application as a red phosphor for NUV chip LED.     

A single red InGaN-based light-emitting diode with a europium (III) ternary complex as mono-phosphor

A novel europium (III) ternary complex, Eu(TPBDTFA)(3)Phen, was designed and synthesized. Photoluminescence measurements show that the energy absorbed by the organic ligands was efficiently transferred to the central Eu(3+) ions, and the complex exhibits strongly red emission due to the (5)D(0)-(7)F(j) transitions of Eu(3+) ions with appropriate CIE (Commission Internationale de l'Eclairage, International Commission on Illumination) chromaticity coordinates (x=0.66, y=0.33) under 310-420 nm light excitation. The luminescence quantum yield for the Eu(3+) complex is 0.18. Thermogravimetric analysis (TGA) confirms a high thermal stability of the complex with a decomposition temperature of 341 degrees C. All the characteristics indicate that the Eu(3+) complex is a highly efficient red phosphor suitable to be excited by near UV light. An intense red-emitting LED was fabricated by combining the mono-phosphor Eu(TPBDTFA)(3)Phen with a approximately 395 nm emitting InGaN chip.     

YBO3:Eu荧光粉的水热法制备及形貌控制

用水热法在低于300℃成功地制备出具有不同形貌的YBO3:Eu3+荧光粉,其反应温度比固相反应了约800℃.研究了初始原料、pH值、反应温度、反应溶剂和催化剂等条件对目的产物形貌及粒度的,得到了具有Vaterite结构、粒度分布均匀的球形荧光粉的最佳合成工艺.在254nm激发下,水热法的球形Y0.95Eu0.05BO3荧光粉最强发射峰位于598nm处,属于Eu3+的5D0→7F1的跃迁,是固相反应所品的1.5倍.这些结果表明,在PDP和荧光灯等显示和照明用荧光粉的制备中水热法具有潜在的应用.     

高温固相法合成R_(2-x)(MoO_4)_3∶xEu~(3+)(R=Y,Gd)红色荧光粉的研究

采用高温固相法合成R2-x(MoO4)3∶xEu3+(R=Y,Gd)系列红色荧光粉.研究了煅烧温度、助熔剂的含量和Eu3+的掺杂量对样品发光性能的影响,并对样品的物相组成、激发和发射光谱进行分析.结果表明,样品Gd0.6(MoO4)3∶1.4Eu3+在800℃左右煅烧时呈单斜晶结构,当煅烧温度提高到950℃左右,呈正交斜晶结构;样品Y0.2(MoO4)3∶1.8Eu3+在800℃左右煅烧时已经完全形成了正交结构,当煅烧温度升高到1000℃左右时,其正交结构得到保持,没有发生相变.其中,助熔剂NH4Cl的含量占样品总量的3%,煅烧温度为1000℃,保温3h得到的样品Gd0.6(MoO4)3∶1.4Eu3+和Y0.2(MoO4)3∶1.8Eu3+的发光性能达到最佳.另外,由激发和发射光谱分析表明,该荧光粉可以被近紫外光(395nm)和蓝光(465nm)有效激发,发射峰值位于612nm的红光,对应于Eu3+离子的5 D0→7 F2跃迁,是一种可应用在紫外光和蓝光芯片激发产生白光LED的红色荧光粉.     

LED用Sr(1-1.5x)Mo0.8Si0.2O3.8:Eu3+x红色荧光粉的制备及其荧光性能

通过高温固相法合成了LED用红色荧光粉Sr(1-1.5x)Mo0.8Si0.2O3.8∶Eu3+x（x=0.1,0.2,0.3,0.4,0.5）。 通过XRD、激发光谱和发射光谱测试了材料的物相组成以及发光性能。 x=0.1样品的XRD谱与JCPDS 08-0482(SrMoO4)的标准卡片相同。 Eu3+代替晶格中Sr2+的位置成为发光中心。 随着Eu3+含量x的增加,593 nm处的5D0-7F1跃迁和614 nm处的5D0-7F2跃迁发射强度会相互转换：当x≤0.4时,以磁偶极5D0-7F1跃迁为主,发射橙色光;而当x=0.5时,以电偶极5D0-7F2跃迁发射为主,发射红光。 可能是过量掺杂的Eu3+离子,只能存在于晶格空位形成缺陷,无法占据SrMoO4中Sr2+的格位中,Eu3+在晶格中占据非对称中心的格位,导致电偶极跃迁变成允许跃迁,从而增加了5D0-7F2跃迁,减弱了5D0-7F1跃迁。 因此,可以通过调节激活剂的含量获得不同发光色的荧光粉。 Eu3+掺杂的硅钼酸锶体系,614 nm激发下,在368 nm处出现宽的基质吸收峰和467 nm处7F0-5D2的跃迁峰,且这2处的吸收峰在x=0.5时比x=0.4时强3倍左右。 材料能非常好的吸收368 nm波长的光,产生颜色可调的橙红色。 与近紫外光LED芯片匹配良好。     

纳米稀土磷酸盐红色荧光粉的合成及性能

以Gd,Y和Eu的硝酸盐与(NH4)2HPO4为原料,采用室温固相反应合成出前驱体,再经过900℃煅烧2h得到(Gd,Y,Eu)PO4纳米荧光粉,运用TG-DTA、XRD、TEM、固体荧光等技术,研究了荧光粉的形成过程、晶体尺寸、形貌及发光性能.结果表明:荧光粉属于单斜晶系,独居石结构的正磷酸盐,空间群为P21/n,平均粒径为60 nm,分散性好,有较高的热稳定性.在396 nm紫外光激发下,纳米荧光粉发出Eu3+的特征红色荧光,发射主峰在613nm,归属于Eu3+离子的5D0→7F2跃迁,该纳米粉体是一种性能优良的荧光材料.     

YTao4：Nb，Eu的发光性能研究

用高温固相反应法合成了铌酸根NbO^3-4和Eu^3 共掺杂的正钽酸盐化合物Y1－xEuxTa1-yNbyO4,研究该体系中紫外光和X射线激发下的发光性能,研究表明,在紫外光激发下,YTaO4:Nb,Eu是一种比较有效的红色发光材料,激发能可以通过NbO^3 4离子传递给Eu^3 ,随钽酸盐中NbO^3-4基团浓度的增中,化合物的结构从M'型YTaO4变成褐钇铌型YNbO4结构,它的发光性质也随之改变。